User Manual
Contents
1. nae 2 Press 3 The indicator 1 The administrator password 3 Enter the group ID of is authenticated Iengibeses anaimakesia M password Group IDs 1 8 7 Exit Press the indicator 6 Registration succeeds 4 Enter the password twice turns red and makes a long q The indicator turns green The password is consists of beep then automatically exit and makes a long beep four digits Note 1 When a password is changed to be 0 00 000 or 0000 the password is disabled 2 When a password is successfully changed you can immediately change the next password by entering another group ID 1 4 User Authentication Card Fingerprint Password Authentication When the device is power on it enters user authentication state Succeed 3 User authentication 1 The device is in user 2 Swipe user card or enter succeeds The indicator turns authentication state password followed by green and makes a long beep Fail The indicator turns red and makes two beeps Note Press after entering a password for authentication The door opens if the entered password is identical with one of the 8 passwords The initial eight passwords for opening the door are empty 1 5 User Deletion Delete one multiple or all registered user s Deleting One User2. ni 2 Press 0 3 Press 3 i m oaa password The indicator turns green gt The indicator turns green and i and makes a long beep makes a long beep 6 Exit 5 Configuration succeeds 4 Configure the concealed The indicator turns red and The indicator turns green mode makes a long beep and makes a long beep 0 enable 1 disable Note When user is authenticating the card or fingerprints or password under Concealed Mode the indicator will still blink correspondingly to denote process status 2 4 Door Sensor Mode Configuration The door sensor has three modes e NONE The door sensor is disabled e NO Normally Open The door sensor will send an alarm signal if it detects the door is closed e NC Normally Close The door sensor will send an alarm signal if it detects the door is open Fo 2 Press 0 3 Press 5 L as amera password The indicator turns green N The indicator turns green and and makes a long beep makes a long beep 6 Exit 5 Conflagration succeeds The indicator turns red and _ The indicator turns green RST OONG NG oiNGre makes a long beep again and makes a long beep eed Aa ad E 2 5 Alarm Configuration Note If an alarm is triggered it can be terminated after the user is authenticated Configuring Alarm Switch Only if the alarm switch is set to be ON will the Failed A
3. User Manual X7 Access Control System Version 1 2 1 Equipment Installation 1 Remove the screw on We banana odeve 3 Fix the back cover on the wall according to the mounting paper 4 Fix the device to the back cover 5 Fix the screw Tamper Alarm Button Structure and Function Access Control System Function 1 When a registered user s identity is verified the Access Control device will send out signal to unlock the door 2 The door sensor will detect the status of the lock If the door is unexpectedly opened or improperly closed the alarm will be triggered 3 It supports the exit button for opening the door from inside 4 It supports door bell 5 If the Access Control device is dismantled the alarm will be triggered 3 Lock Connection AN Warning No operation when power on 1 The system supports NO LOCK and NC LOCK The NO LOCK normally open at power on is connected with NO terminal and the NC LOCK is connected with NC terminal 2 To prevent the generation of self inductance EMF which would affect the system when the electrical lock is linked to the Access Control System it is required to connect one FR107 diode equipped in the package do not reverse the polarities in parallel in order to release the self inductance EMF 1 Device shares
4. 1 Press 2 Press 3 Enter the administrator The indicator is off and makes Enter step of password m gt password a long beep authentication The default password is 1234 5 Exit Press or do not operate the device within 20 seconds The indicator turns red and makes a long beep then automatically exit 4 Authentication succeeds m The indicator turns green Note The default administrator password is 1234 You are advised to change the initial password at the beginning Change Administrator Password 3 Enter a new administrator password 1 The administrator password is authenticated 2 Press 8 Fail The indicator turns red and makes three beeps Succeed 6 Exit The indicator turns red and makes a long beep 5 Password is successfully changed The indicator turns green and makes a long beep 4 Enter the new administrator password again for authentication Note Four digit passwords are automatically verified If passwords less than four digits press to confirm Open Door by Entering Administrator Password Roe 2 Press 0 or 3 Press 0 or ie pe edn eratey password The indicator turns green The indicator turns green and i and makes a long beep makes a long beep 5
5. Exit 4 The door is opened The indicator turns red and The indicator turns green and makes a long beep makes a long beep Note This function can be used to open the door Forgot Administrator Password If administrator password is lost you may reset the password to default through tamper switch Dismantle the device and wait for 30 seconds until a short beep is heard then press the Tamper Switch three times to reset to the initial administrator password this operation must be done within 30 seconds Note The default administrator password is 1234 1 2 Adding Users Register the fingerprint or card of a user or register cards in batches Adding a User 4 Register fingerprint or card Press fingers three times or swipe the card once 1 The administrator is 2 Press 1 authenticated 3 Input user ID twice 4 Register fingerprint or The indicator turns card Press fingers three green and makes a gt times or swipe the long beep card once 5 Registration succeeds The indicator turns green and makes a long beep 6 Exit Press the indicator L_ turns red and makes a m long beep Note 1 Five digits user ID is automatically verified if user ID is less than five digits press to confirm 2 If the user ID is not available the ID number increases automatically It continu
6. a 4 2 Press 2 1 The administrator password is TRC reler Tae aioe LN 3 Enter a user ID press the authenticated a makes a long bash M fingerprint or swipe the card Fail The indicator turns red Succeed and makes three beeps 6 Exit 4 Determine whether the user Press or do not operate the S Vear daeta SUISSE is authentic The indicator device within 20 seconds the The indicator turns green m ume cean UI metes a lon indicator turns red and makes a and makes a long beep eE 9 long beep 2 Note 1 You can either swipe the card press fingerprint or input user ID to delete a user Five digits user ID will be automatically verified if user ID is less than five digits press to confirm 2 After successful deletion the device will automatically enter the process of deleting next user Press to exit Deleting All Users Fe 2 Press 9 3 Press 9 a E password gt The indicator turns green m gt The indicator turns green and i and makes a long beep makes a long beep nt EEEO E TO 4 Deletion of all users succeeds makes a long beep then B a turns green and automatically exit makes a long beep Note In step 3 Press 9 for automatic confirmation Other numbers are considered invalid If an invalid number is entered the device indicator turns red and makes three short beeps then makes a long beep and exits the pr
7. e indicator turns green i 3 4 di is authenticated and makes a long beep Switch 0 enable 1 disable 5 Exit 4 Configuration succeeds The indicator turns red and kK The indicator turns green and makes a long beep makes a long beep Configuring Door Sensor Delay When the door is not closed well after a time period the Door Sensor Delay will raise an alarm to alert users Its configured value is the time period denoting how long after the door is opened will the alarm ring iat 2 Press 0 3 Press 4 is ape ea eae password The indicator turns green The indicator turns green and i and makes a long beep makes a long beep 6 Exit 5 Configuration succeeds 4 Configure the Door Sensor The indicator turns red and The indicator turns green Delay range 1s to 254s makes a long beep and makes a long beep Note 1 Three digit values will be automatically verified For values with less than three digits press to confirm Values greater than 254 are considered invalid 2 When an alarm is triggered the device interior alarm will be triggered first 30 seconds later the device exterior alarm will be triggered Copyright 2015 ZKTeco Inc ZKTeco Logo is a registered trademark of ZKTeco or a related company All other product and company names mentioned are used for
8. es to register new one once a user is successfully registered 3 The registration fails if the user ID fingerprint or the card has been registered the 2 indicator turns red and makes three short beeps When the indicator turns green you can register the user again If you fail to swipe card press fingerprint or enter user ID for three times the device will enter in idle status Registering Cards in Batches 1 The administrator password N 2 Press 6 __ 3 Swipe the first card once is authenticated M Register cards in batches i A Fail The indicator turns red Succeed and makes three beeps 6 Exit The indicator turns red and t 5 Cards are successfully 4 Enter the total number of makes a long beep then m registered in batches cards automatically exit Note 1 In the process of entering the total number of cards three digit numbers are automatically verified For numbers with less than three digits press to confirm Press to enter the total number of cards again 2 You must clear all the registered users before registering cards in batches IDs of the to be registered cards must be consecutive numbers 1 3 Register Access Passwords This device supports 8 passwords each password has a Group ID ranged from 1 8 The default password value is 0 for all groups which means those passwords are disabled
9. ocess 2 Access Control Management 2 1 Unlocking Duration Configuration 2 Press 4 3 Enter the unlockin The indicator turns green EA 0M9 and makes a long beep m gt duration range 1s to 10s 4 Modification of the unlocking duration succeeds The indicator turns green and makes a long beep 1 The administrator password is authenticated 5 Exit The indicator turns red and lt makes a long beep again Note Press 10 for automatic confirmation For values with less than 10 press to confirm Values greater than 10 will be considered invalid 2 2 Authentication Mode Configuration a 2 Press 5 i ee ee password gt The indicator turns green 3 Enter authentication mode and makes a long beep 5 Exit 4 Configuration succeeds The indicator turns red and lt The indicator turns green and makes a long beep makes a long beep Note Details about authentication modes are as follows 4 fingerprint or password or RF Card verification FP PW RF a RE amp PW 5 RF Card and password verification swipe card before entering password FP amp PW Nge and password verification fingerprinting before entering password 2 3 Concealed Mode Configuration Under standby mode when the Concealed Mode is on the indicator will be turned off
10. power with the lock 2 Does not share power with the lock Device does not share power with the lock When Device share power with the lock A When Utock 12V Fliock 1A ULocx 12V I lLock gt 1A B When ULock 12V and the lock is near to the device C When the lock is far apart from the device I device output current ULock lock voltage ILock lock current 3 One device controls one lock Access Control Device 4 Connected with Other Devices mbh Sensor Bell Power zAF Bell Only devices with an alarm lt DC 12V can be connected 5 Connect with Power DC12V Input DC 12V 500mA 50mA in idle status Positive is connected with 12V negative is connected with GND do not reverse the polarities Instructions Step 1 Power on after the device is completely installed on the wall Step 2 Authenticate administrator password and change it immediately Adjust access control parameters which include changing passwords for door opening and setting unlocking duration authentication mode concealed mode door sensor mode and alarm etc Step 3 You may register and authenticate user accounts cards or passwords Operation Instructions 1 User Management 1 1 Administrator Operation To ensure data security of the device users can operate the device only after the administrator password is authenticated Administrator Authentication
11. uthentication Alarm and Door Sensor Alarm be effective The default status of the alarm switch is ON ini 2 Press 0 3 Press 1 E m ron password The indicator turns green The indicator turns green and and makes a long beep makes a long beep 6 Exit 5 The genfiguiaten is The indi successful 4 Configure the alarm setting To m The indicator turns green m 0 enable 1 disable g pagam and makes a long beep Note The Temper Alarm is still effective even if the alarm switch is OFF Configuring Failed Authentication Alarm If the administrator fails in authentication in 3 attempts Failed Authentication Alarm will be triggered No authentication can be made within 20 seconds frat 2 Press 0 3 Press 2 l La neta password The indicator turns green A The indicator turns green and and makes a long beep makes a long beep 6 Exit 5 Configuration succeeds i ieis The indicator turns red and The indicator turns green Ki Failed Authentication Alarm makes a long beep again and makes a long beep itch 0 enable 1 disable Configuring Tamper Alarm If this function is enabled alarms will be raised when the device is dismantled from the wall 1 The administrator password 2 Press 7 3 Configure Tamper Alarm m Y Th
Download Pdf Manuals
Related Search