Christie E400 LED Display Control System Software User Manual
Contents
1. 1 Launch the Christie E400 LED Display Controller software and login as the administrator a Click User gt Advanced Login b Login with the password admin 2 To confirm the display is connected and recognized by the control unit in the Local System Info area ensure Control System has a value of 1 3 Switch to the Display Control tab 4 To confirm the control unit is communicating with all tiles select a color from the Self Test list and click Send Ifthe control unit is communicating with all the tiles each display changes to the selected color 5 Reset the Self Test to Normal and click Send 6 Close the Screen Control dialog Reviewing and modifying the tile configuration 1 Click Screen Config 2 Select Config Screen and click Next 3 On the Sending Board tab of the Screen Config dialog select the resolution of the video source and click Set e The native display resolution is 320 px by 240 px e Change the X and Y coordinates to move the 320 x 240 window as long as the source size is not exceeded 4 Click Save 5 Switch to the Screen Connection tab 6 Click Read from HW Christie E400 LED Display Control System Software User Manual 7 020 101756 01 Rev 1 02 2015 CHAISTIE Configure the array 7 Review the configuration of the tiles in the array and modify as needed The cable layout for the tiles in the array is identified with an S where the first CAT 5 cable starts and the green line sho2. Software User Manual 020 101756 01 Christie E400 LED Display Control System CHRISTIE NOTICES COPYRIGHT AND TRADEMARKS Copyright 2015 Christie Digital Systems USA Inc All rights reserved All brand names and product names are trademarks registered trademarks or trade names of their respective holders GENERAL Every effort has been made to ensure accuracy however in some cases changes in the products or availability could occur which may not be reflected in this document Christie reserves the right to make changes to specifications at any time without notice Performance specifications are typical but may vary depending on conditions beyond Christie s control such as maintenance of the product in proper working conditions Performance specifications are based on information available at the time of printing Christie makes no warranty of any kind with regard to this material including but not limited to implied warranties of fitness for a particular purpose Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material Canadian manufacturing facility is ISO 9001 and 14001 certified WARRANTY Products are warranted under Christie s standard limited warranty the complete details of which are available by contacting your Christie dealer or Christie In addition to the other limitations that may be specified in Christie s standard li
3. e pictures on the screen 1 From the main menu rotate the button to select Advanced Setting and press the button From the Advanced Settings submenu to display the parameters rotate the button Rotate the button to select Offset gt Horizontal X 2 3 4 Set the Horizontal offset 5 Rotate the button to select Vertical Offset Y 6 Set the vertical offset Adjust image quality 1 From the Tools menu select Brightness 2 In the Gamma Adjustment section of the Display Adjustment dialog use the slider to adjust the darker and lighter tones of the source video 3 Click Save To Hardware Set the redundancy backup If the connection to one tile is lost the redundancy backup passes information to the other tiles so the display continues to work normally 1 From the main screen select Screen Config 2 From the Screen Config dialog select Config Screen Christie E400 LED Display Control System Software User Manual 6 020 101756 01 Rev 1 02 2015 CHAISTIE Configure the array 3 Switch to the Sending Board tab 4 In the Hot Backup Setting section click Add Only tiles in the same cascade chain can have a master slave redundancy backup relationship 5 Setthe master board and port number 6 Setthe slave board and port number A slave tile can not be set as a master if it is part of a redundancy backup relationship 7 Click Add 8 Click Save Testing the communication between the control unit and tiles
4. es set all brighness values to zero and raise them to the desired brigtness to resync the tiles Click Save To Hardware Set the input resolution Set the resolution for the home page display of interface which must be consistent with the output resolution of the video source 1 From the main screen select Screen Config 2 From the Screen Config dialog select Config Screen 3 4 In the Sending Board Display Mode section select the resolution of the video source from the Switch to the Sending Board tab Resolution list Click Save Christie E400 LED Display Control System Software User Manual 020 101756 01 Rev 1 02 2015 CHAISTIE Configure the array Load a cabinet configuration file After the screen is powered on if the tile fails to display normally you must load the cabinet files The cabinet files are sent to the control unit through the Christie E400 Controller software 1 From the main screen select Screen Config 2 From the Screen Config dialog select Config Screen 3 Switch to the Scan Board tab 4 Users accessing the Scan Board tab must accept the warnings that changes on the tab can cause issues with the LED panels In the first confirmation dialog click OK In the second confirmation dialog click OK Click Load File In the Open dialog navigate to the rcfg file and click Open Click Send To HW onou Adjust initial picture coordinates Adjust the initial coordinates of th
5. mited warranty and to the extent relevant or applicable to your product the warranty does not cover a Problems or damage occurring during shipment in either direction b Projector lamps See Christie s separate lamp program policy c Problems or damage caused by use of a projector lamp beyond the recommended lamp life or use of a lamp other than a Christie lamp supplied by Christie or an authorized distributor of Christie lamps d Problems or damage caused by combination of a product with non Christie equipment such as distribution systems cameras DVD players etc or use of a product with any non Christie interface device e Problems or damage caused by the use of any lamp replacement part or component purchased or obtained from an unauthorized distributor of Christie lamps replacement parts or components including without limitation any distributor offering Christie lamps replacement parts or components through the internet confirmation of authorized distributors may be obtained from Christie f Problems or damage caused by misuse improper power source accident fire flood lightening earthquake or other natural disaster g Problems or damage caused by improper installation alignment or by equipment modification if by other than Christie service personnel or a Christie authorized repair service provider h Problems or damage caused by use of a product on a motion platform or other movable device where such product has no
6. rce Pixel A group of one red one green and one blue dot Subpixel A pixel is comprised of three subpixels one for each color red green and blue Each subpixel in LED display technology is an LED chip Pixel pitch Specifies the shortest distance from the center of one pixel to the center of the next pixel SMD package size A technical supplier specification related to the pixel size and denotes the size of the surface mounted diode SMD itself for example the 2 5 mm LED tile has a 2121 SMD package size 2121 2 1 mm by 2 1 mm Fill factor Indicates the ratio between the area covered by pixels and the area not covered by pixels Related documentation e Christie 2 5 mm LED Display System Installation Manual P N 020 101412 xx Christie E400 LED Display Control System Software User Manual 4 020 101756 01 Rev 1 02 2015 CHAISTIE Configure the array Perform the following tasks to configure the array 1 Cr Oe Re N Adjust the screen brightness on page 5 Adjust the screen brightness on page 5 Set the input resolution on page 5 Load a cabinet configuration file on page 6 Adjust initial picture coordinates on page 6 Adjust image quality on page 6 Set the redundancy backup on page 6 Restore factory settings on page 8 Adjust the screen brightness From the Tools menu select Brightness From the Display Adjustment page use the slider to adjust the brightness If the brightness is uneven across the til
7. t been designed modified or approved by Christie for such use i Problems or damage caused by use of a projector in the presence of an oil based fog machine or laser based lighting that is unrelated to the projector j For LCD projectors the warranty period specified in the warranty applies only where the LCD projector is in normal use which means the LCD projector is not used more than 8 hours a day 5 days a week k Except where the product is designed for outdoor use problems or damage caused by use of the product outdoors unless such product is protected from precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature set forth in the specifications for such product l Image retention on LCD flat panels m Defects caused by normal wear and tear or otherwise due to normal aging of a product The warranty does not apply to any product where the serial number has been removed or obliterated The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless i Christie has an office in the country where the end user is located or ii the required international warranty fee has been paid The warranty does not obligate Christie to provide any on site warranty service at the product site location PREVENTATIVE MAINTENANCE Preventative maintenance is an important part of the contin
8. tems for used electrical and electronic products Please help us to conserve the environment we live in CHAISTIE Table of Contents Product DOREN abend Terminol0gY un ka eeen A ent de mede ie Pee Ae eke RE ee ae Be i 4 Related documentation 2 2 m m men 4 Consultant iind Adjust the screen brightness eeen 5 Set the input resolution eee 5 Load a cabinet configuration file ee 6 Adjust initial picture coordinates ee 6 Adjust image quality 2 22 ee 6 Set the redundancy backup ee 6 Testing the communication between the control unit and tiles 0005 7 Reviewing and modifying the tile configuration 0 000020 eee 7 Restore factory settings uaaa aaa 8 Christie E400 LED Display Control System Software User Manual 3 020 101756 01 Rev 1 02 2015 CHAISTIE Product overview Christie LED display systems LEDO25 M are modular high quality image display units that can be configured into any size or shape The low energy consumption and the long service life of LED technology create display walls that last LED display systems can be quickly and easily deployed into small display configurations while providing the additional features required for larger and more complex installations Terminology Term Definition Tile A cabinet containing several LED modules Array A group of connected tiles forming a larger display Control unit Controls the LED display system array and video input sou
9. ued and proper operation of your product Please see the Maintenance section for specific maintenance items as they relate to your product Failure to perform maintenance as required and in accordance with the maintenance schedule specified by Christie will void the warranty REGULATORY The product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment The product generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense CAN ICES 3 A NMB 3 A 0 ZS BFS AT LE AAAS SSS IT 2U Bayt SE ASAE OAS FSANZ Betsy 718 ARTEN ARS SHE AS zee Hd Environmental The product is designed and manufactured with high quality materials and components that can be recycled and reused This symbol XK means that electrical and electronic equipment at their end of life should be disposed of separately from regular waste Please dispose of the product appropriately and according to local regulations In the European Union there are separate collection sys
10. ws the path of the daisy chain of cables E identifies the end of the daisy chain Restore factory settings From the main screen select Screen Config From the Screen Config dialog select Config Screen Switch to the Sending Board tab Click Factory Restore E AE a At the confirmation dialog click OK The system is returned to its factory settings 6 At the completion dialog click OK Christie E400 LED Display Control System Software User Manual 020 101756 01 Rev 1 02 2015 Corporate offices Worldwide offices USA Cypress ph 714 236 8610 Canada Kitchener ph 519 744 8005 Consultant offices Italy ph 39 0 2 9902 1161 Australia ph 61 0 7 3624 4888 Brazil ph 55 11 2548 4753 China Beijing ph 86 10 6561 0240 China Shanghai ph 86 21 6278 7708 Eastern Europe and Russian Federation ph 36 0 1 47 48 100 France ph 33 0 1 41 21 44 04 Germany ph 49 2161 664540 India ph 91 080 6708 9999 Japan Tokyo ph 81 3 3599 7481 Korea Seoul ph 82 2 702 1601 Republic of South Africa ph 27 0 11 5100094 For the most current technical documentation please visit www christiedigital com Singapore ph 65 6877 8737 Spain ph 34 91 633 9990 United Arab Emirates ph 971 43206688 United Kingdom ph 44 0 118 977 8000 CHRISTIE
Download Pdf Manuals
Related Search