USERS MANUAL - Empirical Labs Inc.
Contents
1. aA Pp TT Features amp Specs What Is The Fatso Using for the First Time Example Settings The Compressor Four Types Recall Sheet The Saturation amp Warmth Circuits The Tranny Block Diagram Basic Wiring and Stereo Linking Troubleshooting Fuse Replacement AC Voltage Select User Notes Customer Comments Warranty BACK TO TABLE OF CONTENTS Features Soft clip features modeled after broadband tape saturation WITHOUT THE NOISE Smooth clipping up to 20 THD User programmable high frequency saturation simulating the softening for which analog tape and phonographs are known This is the Warmth control on FATSO Switchable transformer circuits which can add the musical artifacts generated by classic devices like NEVE API etc These artifacts include frequency rounding low order clipping amp intermodular distortion transient clipping and some other very musical non linearities Four compression modes One for tracking one general purpose one bus compressor and SPANK see below All LINKABLE Classic knee compressor sound that really grabs SPANKI An additional limiter that musically smashes the dynamic range can be used to stop clipping before digital recorders There is a subtle knee followed by hard limiting Huge DISTRESSOR knobs with high resolution numbering For easy readability and repeatable settings They also to 10 1 2 Distortion indicator l2. To sum up the musical results of our Tranny circuit there will be a little more edge in the midrange and the super low frequencies will have been harmonically altered in a way that allows them to sound louder even though the peaks are less than the original Playback on small speakers will show an improved audibility of low end from the result of the psycho acoustically pleasing distortion the Tranny adds Something really interesting we noticed even though fundamentals below 100Hz cannot show up on the little speakers because of the natural way a transformer saturates the harmonics give your ears enough clues that your mind somehow fills in the fundamental If you have the time try this experiment put 40 Hz sine wave tone into the Fatso and match the Tranny level to the bypassed level then put the output thru a small speaker A B the processed Tranny signal with the bypassed signal in the small speaker You will probably smile Fatso Block Diagram Main Audio Path Active Outputs Input Drs 1 4 Phone Filter 8 7 ge Vv 1 4 Phone Master XLR Gain Bypass One of two channels shown Control Voltage Warmth Envelope Gen Compressor Envelope Gen Normalled To Front Panel Bargraph To Front Panel Insert Digital Bargraph Controls Detector Circuits Digital DC Link to other Controls channel and External Li
3. You will probably find so many uses for the Fatso as we did but let s just go over a couple quick scenarios here Let s say you have a vocal either live or in the studio that seems lifeless or needs presence and intensity First lets set the compressor fact you should always set the compressor up first because it interacts with the other processors in the Fatso For excessively dynamic vocals would go right to the TRACKING compressor type with both the green and yellow LEDs lit in the compressor select area Adjust the input til you get 5 dB of GR to start with and adjust the output knob until there s not a great difference between the bypassed and un bypassed levels Remember the Bypass switch is multiplexed and to cycle in and out of bypass click twice quickly Next decide if the vocal has a brittle edge on the top end If so you have two other ways to soften The most subtle is the Tranny which engages a specially tweeked transformer circuit that enhances the midrange while softening extreme transients and fattens 200 hz and below That may not be what you need on vocs tho Try the Warmth control for less subtle high end softening This circuit is a wierd dynamic filter not too far removed from de essing except it is above most sibilant freqs and works on a different principle and filter type ok so it is far removed This circuit is really useful on vocs that are bright or have 10KHz and above boosted heavily with EQ In fact w
4. 9 The Tranny The Tranny is short for transformer In the old days to interconnect between audio components with low impedance cabling i e noise resistant the audio engineer used transformers on the input and outputs Transformers isolate two signals using wire coils wound close to each other but not actually touching They were never that linear and often introduced saturation and LF distortion as well as changing the frequency response Transformer design and use was an art hats off to Rupert NEVE and there were always tradeoffs However it has been widely known that a good audio transformer circuit can do wonderful things to an audio signal This was the goal of our TRANNY circuit We have tried to emulate the desirable characteristics of the good old input output transformers in a consistent musical way and in a selectable fashion Many of the older transformers had certain low frequency characteristics that some of our newer and more linear circuits and transformers have overcome As frequency goes down the audio signal gets more like DC i e slower moving Transformers don t pass DC current thru them so strange things start happening as the audio goes deeper The addition of harmonics and peak saturation along with frequency and phase changes on the low frequencies occurs We found that we could capture the low frequency effects of large and now expensive older output transformers in a weird internally buffered switchable design
5. Complete mastering facilities in a double height rack mount unit Contact Eventide Inc at 201 641 1200 4 Three dimensional software for the Eventide DSP4000 and H3000 Contact Eventide Inc
6. put a finger on one warmth button while pressing the other warmth simultaneously The orange link LED will lite on both channels Let up on both buttons simultaneously There are two main link effects 1 The compressors are linked and their gain reduction will match provided both are enabled 2 The Channel 1 Bypass control now controls both channels Bypass Tranny It is usually best to match all front panel settings on the two left and right units to maintain imaging However unlike most units the user has the option to treat the left and right channels differently Sometimes for room mics keeping the units unlinked actually makes them sound more stereo This is due to unique left and right ambient envelopes widening the stereo image For 5 1 surround where multiple units must be locked together chain one unit to the next with a short phone plug cable in the External Link jacks match controls and put units in Link mode Two interchangeable External Link jacks are provided to go to and from each Fatso The gain reduction will now match on all units linked this way For standard 5 1 processing three Fatsoes will be used The compressor bargraphs on the bottom will indicate that the two channels are responding together Due to the high resolution of the bargraph there may be slight differences in the left right bargraph response mostly on the first few LED s i e 1dB 2dB 3dB of gain reduction A note on Bypass and the Multiple
7. STEREO or AUDIOPHILE applications like CD players Ram Recorders etc don t use any compression unless you really want to change the dynamics drastically Buss Type compression is going to be subtle but won t keep your dynamics within a narrow range The GP will be useful for noisy parties or a noisy environment where low level music will be brought up closer to the level of the loud parts Verrrrrry useful on dynamic classical music My copy of Beethoven s 3 Symphony had quiet sections that would get lost behind my computers fan noise without GP on FOR MAKING TAPE COPIES LOUDER ETC Use the same rules as above unless you want to really smash something like radio stations do In that case try the Tracking or even the SPANK type compressors Otherwise use the Buss compressor for very gentle gain control or no compression 6 5 0 zey 5 037 Aue 1 2 yndu y IM UOISSeS LSNIMIOVYL ag L 5 ok 0g 4 yoq 1 55910 yul OL 05 Wd i mo 6 gt l syuuem yoq aoe ul oL 5 se OANNWHL peuuld O d 9 ab
8. ae e 2 910 as LSNIMOVYL a ArT OTOT z y 0 OZ 6 0 6 909 o 6 40 TJ SS 84 ne 10 nao 5 OssvdAg dwog sO ao Oannyy Pad L Ossvaag M0 O O gna dwog 209 super 49 OANNWHL 04666 6 see L 1NdLNO z s YUE 0 z si 910 14015595 LSNI MOVYEL s mo 1 OL 02 O 97 07 07 CO oann sedas i JNYdS Ossvdag S as Ossvasa 5 Supon S sna OANNWHL gna D 01 sm Zi mem sie than L Om i z s oF 19945 11e99y 1f 05174 BACK TO TABLE OF CONTENTS Saturation and Distortion Generator The old sought after vintage gear is not anywhere near as accurate or linear as devices made today but certain faults or non linearities are exactly the reason some sell today at 100 time
9. lights that indicate some reference operating levels A 0 VU yellow LED light indicates around 1 THD and the red Pinned LED indicates 5 THD or more These LED s are an excellent guide to where the user is in the Grunge Department and can help to avoid turning the music into an overwell mess You will find that the harmonic distortion is generally more obvious on overall mixes and complex programs On individual instruments sometimes 10 distortion sounds fat and analog and isn t heard as distortion at all Warmth Processor The Warmth circuit is by far the most complex part of the Fatso Basically it is a very strange high frequency HF gain control circuit or High Frequency limiter It operates very fast and should be very unobtrusive in operation since it gets in and out of the way very quickly The desired result is akin to the HF saturation that analog tape exhibits when the high frequency amplitude interacts with the tape recorder bias to produce self erasure of the certain frequencies We provide a very accurate display of the HF attenuation with the upper FATSO bargraph showing the gain reduction at 20KHZ The nature of the filter allows the corner frequency to move as attenuation occurs We provide just one control for the warmth but there are other ways to control the overall action of this circuit If you do decide to use the compressor set it up first because it affects the operation of the warmth There is heavy interaction
10. lower fundamental Great on direct bass The Fatso compressors are fabulous on bass too The buss compressor is good for an already compressed or very evenly played bass since it will leave the transients and remaining dynamics in It will also allow you to use varying amounts of grunge since it is such a gentle compressor that wont really nail the bass level in place Just by turning the input up one can add or remove distortion The GP is another compressor that may allow the dynamics to come thru but due to the long release excessive pops or plucks may create holes in an overly dynamic bass part The Tracking compressor is a favorite again for bass both the green and yellow LED lit It is the most Distressor like compressor in the Fatso with a fast attack and release along with a smooth knee SPANK is useful for a more aggressive level control on Bass As you can see there are lots of options here The warmth control may be useful for some trebly over eq d basses but generally it may find limited use here Again watch for over smashing or grunging Caution should be observed if you are going to tape You cannot un distort Elec guitar Awide range of settings can be used To get rid of edgy attacks use the quick attack fast release of the tracking compressor If the guitar is too dynamic the compressor combined with the saturator and tranny circuits may be the answer Sometimes the guitar just needs a touch of fatness without losing at
11. pretty safe LN1176 Type knee compressor with a pretty quick attack and release That might be all you need Using up to 10 dB of compression should be fine with really dynamic vocs Alternately you can try one of the other compressor types even SPANK to grab occasional peaks and then quickly get out of the way 3 SKAMPLE SETTINGS part 2 If the top end is too sizzly or spitty you can try the warmth control maybe adding up to 6dB of warmth on the peaks This is not a de essing function since it affects freqs above the most trouble some sibilant freqs nonetheless you may find it helps take some of the hissy sound out of a source Tranny may be useful on exceptionally low vocals as it will warm the low tones to some degree It will also roll the super subs off but generally Tranny will not radically affect most vocal sources Various Instruments Bass Fatso is gonna be really useful here Bass is notoriously hard to round out and clarify sometimes but the Fatso has many ways to help First if a low bass tone is too pure and sine wave like it will fall off on small speakers By this we mean it will not be audible because most of the bass frequencies are below the range of the speakers The Tranny is the solution combined with the saturator circuits These will generate upper harmonics that will be musically related These harmonics will be reproduced on small speakers and the human ear and mind will psycho acoustically fill in the
12. CD 16 bit quality However if you are compressing a noisy signal the noise is pushed up along with the soft signals If you have 20 dB of gain reduction on a room mic that has a 90 dB S N the noise floor will be raised 20 dB in quiet areas bringing the noise floor up to 70 dB Since the FATSO is capable of lots of compression without sounding unnatural you can often bring hiss levels up undesirably Remember your current input level and then ensure that the noise is coming from outside the unit by turning the input knob off to 0 All noise should disappear Try gating before compressing Changing the fuse Caution Always unplug unit before removing cover Pull out the power plug from the AC outlet open unit and ensure fuse closest to rear of the unit is blown Note The fuse closer to the front panel is a spare fuse and is not connected to anything Gently pry out one end of the fuse and then the other replacing it with extra fuse provided near battery holder in front of unit A small screwdriver may be helpful Before putting cover on plug in unit keeping hands out of the box ensure that the fuse doesn t blow again indicating a possibly more serious problem see troubleshooting If OK unplug unit screw down top cover and return the unit to normal use Any fuse from 3 to 6A should be safe but 3A 1 3A is what is specified and used at factory Replace spare fuse in front if available We went to the expense to keep an extra fuse
13. aked first The fast attack of the Tracking Compressor can help get a glassy full sound since the pick noise will be attenuated and the sustain lengthened Also the threshold of the warmth circuits were lowered so they could grab the transient picked edges easier This allowed a solo instrument to be louder without the sharp attacks hurting Sometimes you may want to keep the dynamic range of a plucked instrument but need to smooth out just the hard front edge of the attack Warmth processing is perfect here Adjust the warmth until you have a smoother more natural sound usually 3 10 dB of HF attenuation is enough In addition to your normal monitoring levels listen very softly and very loudly to the adjusted track to make sure it isn t too dull or still in need of softening Acoustic guitars can be so creamy Many times you will have an acoustic part that is very even and you can nicely brighten it up with a top end EQ high frequencies except for that one part where he really bangs it Use the Warmth control to grab those clangy brash freqs Usually 1 5 dB is enough but on really brittle parts 10 15 dB on peaks may be ok on extreme peaks Again don t over do it especially during tracking Listen really softly and really loudly to test evenness 4 SKAMPLE SETTINGS part 3 Piano Keys Acoustic pianos often need less attack amp more sustain to fit into a mix but there are millions of exceptions As far as the compression par
14. al Labs for its FATSO processor Craig Anderton LIL FREQ Hey Dave so got the box plugged it in on an Etta James vocal that was having problems with and it 4 amp rocks This is a great box my friend can see anybody with a DAW wanting to use this thing am using the shelving DS ing and transformer out and am just thrilled Congratulations It absolutely complements the digital crap that am forced to use wooo hooo Ed Cherney I finally got to hear Empirical Labs Lil FrEQ a monster that will destroy the way you think about EQ This single channel unit has two shelving bands tunable low cut four parametric bands dynamic EQ for de essing and direct box input all noiseless and distortion free Best of all its smooth processing is absolutely addictive Sweet George Peterson Mix Magazine Rev4 3 14 Warranty and Factory Service All Empirical Labs Inc products are covered by a limited warranty which covers full parts and labor for one year from the purchase date The warranty is only effective if the owner has returned his or her warranty card See warranty card for further details Should problems arise call your dealer or distributor to determine the state of your warranty and if it becomes necessary pack the unit up well enclose a note explaining the problem and return to Empirical Labs for repair Include your name address phone and the date of purchase Send the unit with freight pr
15. armth is really useful used in conjunction with high freq eq boost as it will only grab the parts that are excessively bright or plasticky and get out of the way in less than a millisecond Use it as an EQ tamer As you progress from 1 7 on the warmth control more and more high freguencies will be grabbed and eventually you will start muffling the signal DON T DO THAT Be very careful not to overuse the warmth control 1 5 dB of Warmth is a lot By now that distant thin vocal should be HOT and in your face When using the compressor and warmth together remember the interaction Apply this same type of thinking to other sources instruments Don t be afraid to use the warmth without any other processing or just the compressor or just the Tranny to fatten low end Also remember the unit is always passing the signal through the saturation circuits with no LED s on whatsoever Don t feel like you have to use all the processing within the unit because that will surely get you in trouble sooner than later SEE EXAMPLE SETTINGS ON NEXT PAGE 2 EXAMPLE SETTINGS The Fatso was designed essentially to integrate frequencies in a musical manner and provide some fool proof vintage sounding compression Generally it is difficult to make the unit sound unnatural due to its vintage topology But it is possible to overdo things Let s go over the four types of processing the Fatso provides and describe what they do and generally when they would
16. ast release 1 4 dB of compression is usual for this compressor type Very soft knee Five or more dB of Buss compression is hitting it hard 2 General Purpose A medium attack slow release type that sounds pretty invisible while able to maintain a consistent RMS level The slow release will not pull things into your face unnaturally 3 Tracking Compressor when both top LED s are lit an 1176 type compressor is enabled that is great for tracking instruments and vocals during the recording process or during mixdown 4 SPANK This is a radical limiter type compressor that was specifically designed to emulate the nice squeeze of the older SSL talkback compressors from the 70 s amp 80 s Quite a bit higher fidelity though as you will notice By combining SPANK with any of the other 3 types of compressors one really has 7 compressor types or ratios although the SPANK s aggressive nature will tend to dominate when combined The release curve of all types is logarithmic meaning it lets off quickly at first and then slows This release curve is a big part of the FATSO s compressor sound Just what is a soft knee A soft knee is a compression curve where the first few dB of gain reduction occur at very low ratios gradually increasing as the signal increases gets louder This makes the onset of compression very hard to detect The knee usually extends for a few dB and gradually flattens out toward a final ratio All the Fatso co
17. be used Fatso s Four Types of Processing 1 Harmonic Generation and Soft clipper Basically this is a distortion generator Anytime you pass a signal thru the Fatso it passes thru this part except in bypass This processing is useful to softly but instantly clip peaks and transients allowing more average level 2 High Frequency Saturation WARMTH This circuit is meant to simulate the softening of the high end that occurs with analog tape Basically as the warmth is increased overly bright signals and transients will be quickly attenuated The time constants are very nearly instant so the high freqs return very quickly after a loud burst 3 Transformer amp Tape Head Emulation This is a simulation of the effect of input and output transformers of older devices and adds the low frequency harmonics that characterize analog tape This is extremely useful on pure low frequency type tones that don t cut thru small speakers It adds upper warm harmonics to frequencies below 150Hz especially those even lower such as 40Hz the low string on a bass guitar helping it to cut thru on smaller speakers 4 Classic Knee Compression Empirical Labs Style This is your typical automatic leveling device that you find used on just about every instrument and vocal track as well as on the overall buss Only its Empirical Labs compression smooth sweet but in your face Reminds me of an old girl friend See the compression guide on page 6 for description
18. between the compressor and warmth settings The warmth control is a step control with 8 ranges no warmth action no LEDs lit on up thru the highest setting of 7 Perhaps the best way to think of the settings is as compressor threshold with 7 having the lowest threshold and the most warmth responding quickly and often to high frequency content Just remember that instead of controlling the overall level this warmth compressor threshold only affects the high frequencies Thousands of hours of experimentation were involved in developing the filter to make it capable of large gain reduction at 20Khz without really dulling all the freqs frequencies STILL ONE MUST BE CAREFUL NOT TO OVER DUE THE AMOUNT OF WARMTH USED The temptation is to say oh wow that s great so fat and warm let s warm DON T GO THERE Trust the meters when doubt 2 5 dB is quite a bit of warmth on most signals There may be times where 10 dB does the perfect job but trust us that if you see all the LED s light on the warmth bargraph you are being very naughty You will find the warmth to be useful all by itself many times without the compressor or Tranny or much saturation Originally the FATSO was only going to have the saturation and this warmth circuit but as our research went on we decided the extra circuitry of the Tranny and compressor would provide some of the other important nonlinear elements of tape compression and vintage gear as well
19. d probably get away with just using that Mitchell Froom sold a couple of 1176 s and have replaced them with the Distressors which do a great job of emulating the 1176 s Michael Wagener Ozzy Osbourne Extreme Metallica In general really like where Dave Derr s ear leads him one of pro audios truly independent thinkers I m a huge fan of the box the Distressor use it for bringing up the goosh on ambient sources and for saturating snares toms and kicks George Massenburg Comments About the FATSO Jr In a word the FATSO is a very good answer to what a lot of people loathe about digital recording It smoothes out the sharp brittle edges to exactly the extent you choose and fills in the hairline cracks just right use one on almost every mix do could easily use one and possibly two more George Massenburg People used to have to hunt for old expensive gear to get the kind of sounds that the FATSO gives me Ed Cherney The Rolling Stones Bonnie Raitt Bob Dylan Eric Clapton Jackson Browne Susan Tedeschi Etta James et al Best new Signal Processor EQ AES Awards Empirical Labs Fatso took this category despite the introduction of a variety of cool new processors Who can resist the best aspects of analog tape combined with great compression EQ Magazine The winner of the highly coveted I m going to write you a check right after the show award was picked up by Empiric
20. epaid to the address below and mark it Attn Service EMPIRICAL LABS 41 Beverwyck Rd Lake Hiawatha NJ 07034 Phone 973 541 9447 Also see our website at www EmpiricalLabs com Additional Contact and E mail Information can be found there Please pack the unit in original carton if possible Otherwise pack with bubble pack and or foam in a thick corrugated box Shipping companies are absolutely brutal with large packages and you must take every precaution against constant dropping throwing and crushing We are not liable for products damaged during shipping Do not attempt to modify or make adjustments to your FATSO until you have notified Empirical Labs and been sent the necessary information There are a number of critical adjust ments that cannot be made properly without the calibration tools we have here at the factory Any sign of internal adjustment by the user will void your warranty with the exception of changing the fuses or line voltage selection Empirical Labs Inc takes no responsibility for the safety of anyone opening the FATSO for any reason There are dangerous voltages present when the unit is plugged in Refer unit to properly qualified service center or return to factory Other Empirical Labs Products 1 The Distressor Classic Knee Compressor Found on thousands of major records 2 Lil FrEQ The Ultimate Analog Equalizer amp De esser with built in DI Box 3 Masderring Lab for Eventide DSP4000
21. ights A 0 VU LED and a Pinned 5 LED No hard clipping until a few dB past Pinned Sidechain output and input for eq ing control signals Locked calibrated output level Allows speed in setting tape and live mix levels Foolproof operation it s almost impossible to get a bad sound Single height and light weight Two channels of classic sound in a small extremely reliable package Discrete and integrated combination the best of speed linearity with repeatability Hand tested amp selected components All metal film and Roederstein resistors in the audio path top quality components most being high temperature military spec parts Q Switchable 115 230 volt operation Extra fuse provided inside unit True bypass Know what it s really doing All contacts doubled up for maximum reliability No internal audio connectors XLR and 1 4 phone ins and outs XLR fully balanced transformerless design pin 2 hot Changeable by user to pin 3 hot Q No internal connectors high reliability parts and military grade switches and relays Three year unlimited warranty Interface and features found nowhere else Allows processing not readily available in our current digital domain New life for analog processing Hand wired calibrated in USA Shipping weight 13 25Lbs Freq Response is 2 Hz to 60 kHz in clean audio mode 0 3 dB Dynamic Range 110 dB from max
22. imum output 20 THDsoft clipping to minimum output Greater than 100 dB signal to noise Distortion Ranges between 06 and 20 depending on mode and settings DC coupled Input and Outputs High quality audio caps used internally Compressor Time Constants Attack range 1mS 200mS Release range 05 sec to 3 5 seconds Attack and Releases are fixed by the compression type selected Power Consumption 35 Watts Max typically 115 Empirical Labs Something Old Something New 1 BACK TO TABLE OF CONTENTS Wat 15 tHe Fatso HM SUCH AN EASY QUESTION The EL7 FATSO is a modern digitally controlled analog device that offers many of the musical non linearities exhibited by the older tube class A discrete and magnetic tape mediums This two channel audio processor will musically integrate frequencies and transients and increase the apparant volume without actual increase in peak levels In addition two channels of famous Empirical Labs compression are provided There are several compressor types with fixed attacks and releases if you want a fully controllable compressor you will need the Empirical Labs Distressor Users can enhance amp soften the sound of mediums such as modular digital multitracks MDM s HD recorders Dat recorders Ram Recorders etc Mixdown engineers will have an option not to use bulky expensive and often flaky analog tape recorders to get the warmth and sweet high end they ve come to re
23. ink In of the same channel The sidechain must not have appreciable delay nor be out of phase since it will affect the response time and possibly comb filter the control signals when in Stereo 3 To set quick 4 tape levels try setting output at 8 and drive input knob until compression occurs For ADAT s try 6 to 7 output level 4 Remember you can combine different compressors with SPANK Type compressor 11 Troubleshooting Unit forgets where it was when power was shut off Non Volatile memory cap has become defective or possibly some other type of logic failure has occurred Contact the factory for servicing No sign of life Check power cord for firm connection If still no life unplug unit and open top cover by removing all top screws and check fuse toward rear next to transformer If it is blown pry it out and replace it with extra fuse provided in fuse holder toward front of chassis If fuse is OK make sure your Voltage select switch is set to current wall outlet voltage 115 230 VAC Unit keeps blowing fuses Check internal voltage select switch for proper settings 115 230 Otherwise suspect a short or power supply problem Try to make sure there is nothing trapped under the PC board shorting to the metal case Attentive visual inspection is still the most effective troubleshooting tool available See below Unit runs hot Leave a space above or below it or mount in cooler rack Unit is on but not doing anythi
24. inside you should too Line Voltage Select Changing the voltage for 230 or 115 operation also involves unplugging the unit and removing top cover Inside on the right as the front of the unit faces you is a switch with 115 or 230V showing on its face Select the desired voltage by sliding the switch until it indicates that voltage and you re done Replace cover and screws 12 5 BACK TO TABLE OF CONTENTS Customer Comments Comments About the DISTRESSOR Every once in a while a product comes along with classic written all over it Andina certain sense of the word this product actually is a classic already Mix Magazine Dear Empirical I m LA based producer and an owner of a Distressor The unit is really awesome I ve used it on guitars bass room mics vocals it works great on everything I ve used it on records I ve made with Beck U2 Etta James Hole and lots of others Joe Chicarelli After buying a Distressor had an epiphany Having used software plug ins for years often didn t hear or understand the affects of various controls After getting my Distressor and using it and hearing the obvious affects of the attack and release controls was able to go back and use the Plug ins with a new understanding Email One piece of gear definitely recommend is a compressor called the Distressor It s really great for just about everything and if you had to use just one compressor you coul
25. ly on for so many decades Owners of Adats MDM s RAM and modern hard disk recorders can finally put a stop to complaints about the coldness and brittle edge of their mixes and instruments with the rounded and musically non linear elements of vintage analog Finally audiophiles can bring back the warmth and cuddly sound of LP s and tapes to their CD players and other digital reproduction mediums Fatso s Four Types of Processing See next page for detailed description 1 Harmonic Generation and Soft Clipper Distortion generation 2 High Frequency Saturation WARMTH 3 Transformer amp Tape Head Emulation 4 Classic Knee Compression Empirical Labs Style Using the Fatso for the first time Hookup is straightforward Either the XLR s or phone jacks can be used In relation to the phone jack tips pin 2 is wired hot on the XLR s But if you re using the XLR s in and out it doesn t matter which pin is hot as long as you re cabling is in phase If you use a single ended XLR output leave unused pin floating Connecting all input pins is preferred but the unit will operate fine if unused pins aren t tied to ground Hookup directions are also located on the rear panel of unit near the connectors See page 11 for more detailed wiring instructions It s advisable to mount in a cool rack position as the Fatso Jr tends to run quite warm Fatso is ideal for sources that sound brittle bright or pointy or have excessive dynamic range
26. mpressor types have dominant knees The Buss Type Compressor has a knee that can be as long as 15 dB depending on the source VINTAGE COMPRESSOR EMULATION Since the unit is based on the oldest compressor topology the unit can be made to sound similar to older classics The nonlinear nature of the older gain control elements of opto couplers FET s pentode or triode tube bias or mu modulation etc can be closely emulated if proper settings are used Some Examples Opto VCA tube models To simulate the old light controlled units the LA2 LA4 DeMaria Meek units try the GP general purpose compressor with the Tranny on Adjust input and outputs to your taste Remember our LED metering deflects much faster than the old VU s so don t be afraid to hit the unit quite hard 10 20 dB of compression on peaks This emulation is not as close as the Distressors OPTO mode however DBX160 2 1 for over easy Try BUSS GP Type Compressor no Tranny LN1176 Use the Tracking Type compressor that lights both the green and yellow LED s in the compressor section SSL type buss compression Use the Buss type Compressor Tranny SSL Talk back compressor Use SPANK Spank that mix dang it Unlike the older units the FATSO is uniform and predictable from one unit to the next Precise factory calibration assures that if you go from one FATSO to the next these settings will all sound the same FOR HOME
27. ng The unit may be bypassed or operating subtly If bypassed you need to press the BY PASS button so red LED goes off The input and output levels should always affect it unless bypassed Bargraph shows gain reduction but very little or none is actually occurring The unit is possibly severely out of adjustment We use very stable trim pots and high quality components but it is possible that long term component aging or failure may require factory re calibration Also dampness or something spilled into the Fatso can cause this phenomenon At present you will have to return the FATSO to factory for re calibration In the future there will be local dealers and or service centers to help Distorted output If there is severe un musical distortion chances are you re hard clipping Check that the output cable is properly wired and any unused output pins 2 or 3 on XLR are floating left unconnected Shorting an output pin will not harm the unit but can show up as distortion in the output driver The distortion this unit is meant to impart is harmonic and should not sound like crackly distortion caused by hard clipping If the pinned LED stays on you must turn down the input No output level Make sure there is audio getting to the unit and that the input and output levels are turned up Unit pops or unnaturally pumps with low frequencies Try a different compressor TYPE Unit seems noisy The dynamic range of the FATSO is greater than
28. nics to the low fregs while rolling off some of the subsonics Overhead Mics Also for over dynamic and brash cymbals the warmth processing can be a real sweetener To soften the edge of cymbals try Warmth on 4 or 5 setting and turn the input up to control the amount of warmth Watch anything over 5 dB of warmth as this is really attenuating a lot of high end But if it is just the front edge of the cymbals it can be verrrrrry pleasing Of course compression may be used but if itis set it up first Room mics Again the most gentle compressor for the room mics will be the BUSS compressor However radical room compression is currently in style The Tracking compressor Green and Yellow compressor LED s lit will be useful over a wide range from 1 dB of GR to 10 dB depending on what you are going for and what the tracks will allow But for over the top treatment try SPANK The SPANK is not the NUKE of the Distressor yet it can add some of the same sustain and intense size to it The bargraph can be run right offscale with the SPANK type compressor and still be a very useful sound Fifteen to twenty dB of compression is starting to have that John Bonham thing that the Distressor can do Watch over heating the tracks though Also any loud cymbal playing will become annoying with lots of compression on the room mic Sometimes it may help to feed a compressed room signal back to the drummer while tracking to give him a feel for balancing his cymbals and d
29. nk Stereo Link Note the position of the Warmth and Tranny circuits after the Compressor accounting for the large interaction between their controls 10 Basic Wiring Wiring is straightforward Connect AC line cord to 3 prong jack plug in XLR or phone plug ins and outs and you re wired The phone and XLR input jacks are differential at the output only the XLR is differential balanced The output phone jack tip is wired to pin 2 of the XLR out and therefore is in phase with that pin The only possible problem is if you attach one of the XLR output pins 2 or 3 to ground A separate amplifier drives each of these pins so grounding one of them will short the associated amplifier out Therefore if you only use pin 2 on your output cable leave pin 3 floating unconnected and vice versa The phone jack ins and outs will be out of phase with pin 3 since the unit is wired pin 2 hot from the factory see note below Pin 1 should almost always be grounded on the XLR cables but there are times where a buzz can be introduced thru chassis grounds Note It is possible to change the wiring of the connectors inside since they are hand wired A user can therefore make XLR pin two or three hot in relation to the phone jacks Always unplug unit before making any changes Our company cannot be responsible for damage to unit or electric shock to anyone trying any modifications Stereo Operation amp 5 1 Surround Use To put the Fatso into Stereo mode
30. oal is to make that CD player have the warmth and softness of the old tape recorders and records If you were going to use compression set it up first since it interacts with the other settings But for now let s not use any compression here First adjust unity gain thru the Fatso Set the input until the OVU LED glows on peaks from time to time This will set up the saturation to emulate some nominal tape like distortion Next if you want the low end to have more bite the tranny may be useful but for most digital recordings try messing with the warmth control Allow 1 5 dB of warmth to occur on peaks When AB ing it to the original signal new softness and fatness will be noticed immediately You will be able to listen to things a little louder than usual DJ level controller and master PUMP device Place the Fatso before your power amps or at the output of your DJ mixer to level out or fatten up the whole show The Buss compressor can level out volume differences while keeping the smack intact You can then add some top EQ and have the warmth hold back the brittle edges The Tranny may help on smaller systems to get the low freqs clearer but if you have lots of subsonic info you may want to keep Tranny out of line since it will roll off the exceptionally low low stuff Vocals There so many ways to use Fatso here During tracking turn on the Tracking Compressor which lites the green and yellow LED in the compressor area This is a
31. of the 4 compressor types CD Player amp Buss Fattening This was almost the original intent of the Fatso That is it was a two channel device that could make a stereo digital signal sound analog and integrate the different frequencies in a musical way It could be used as a stereo device thru which one could mix or transfer to or from a digital medium to make it sound very analog tape like For those who aren t used to the Jargon A BUSS is usually a pair of channels that have pre mixed instruments or stereo music on them The Left amp Right outputs of your CD player could be considered a 2 channel buss In the recording studio it is more often applied to the final left and right channel mix or to something such as all the drums mixed down to 2 tracks a submix so that instead of moving 12 faders at once to move drums up or down you only have to grab those two MIXDOWN PRE PROCESSOR Again of the original intended uses By placing the Fatso immediately before a digital mixdown recorder such as a DAT CD HD or RAM recorder the recording engineer should be able to get the sweet high end and low frequency fatness that he could mixing to an analog tape recorder Compression should usually be the Buss type use the warmth to soften the high end and the Tranny to add some edge and warm harmonics to the Low frequencies CD PLAYERS amp Other Digital Recorders Take the output of the CD player into the Fatso input Our first g
32. rums Distortion device The Fatso has very smooth clipping up until about 20 Folks have already used the Fatso as a distortion box with great effectiveness and musicality The warmth provides another way to roll off some harsh distortion grit as well fattening up the lower harmonics The Tranny will drastically distort sub frequencies below around 50Hz but it is adding the 2 and 3 harmonics that sound very ballsy on those low tones You may even find that plugging a guitar and bass directly in can work although the impedance and gain structure are more suited to line level or a Direct box output Effects warmer Try using the Fatso as a tape delay simulator by putting it after a digital delay Turn the compression on BUSS compression and the warmth on little Use the Tranny to roll off subs and pump harmonics into the low frequencies Similarly try the Fatso on a digital reverb to simulate the plate reverb non linearites and magnetic transducers It works great 5 BACK TO TABLE OF CONTENTS The Compressor and ts Ratios Each Fatso compressor or compressor TYPE as we have termed it sets the threshold the ratio in the standard sense of the word the attack and decay This was done to provide an easy to set yet versatile group of curves There are essentially 4 discrete compressors with the fourth able to be combined with the other three THE FOUR FATSO COMPRESSOR TYPES 1 Buss very gentle 2 1 type ratio with Slow attack and f
33. s their original value They color the sound with distortion and frequency response shaping Getting the frequency response flat to 20kHz and having distortion below 5 used to be an achievement Today in 2000AD a 35 cent op amp is flat to 3 MHz and produces distortion below 002 Getting things accurate in the digital age is relatively cheap and easy but getting a piece of gear to be musical and fun to use is something else It is well known that the triode distortion in tube circuits produces lots of 2nd and 3rd harmonics in somewhat varying ratios These lower order harmonics form the octave and the octave and a fifth to the fundamental musical tones They are actually musical distortion Harmonics above the 2nd and 3rd get increasingly harsh and unmusical and therefore should be lower in amplitude lt 60 dB to keep with our line of thinking Second harmonic is considered to be the warmest and most consonant harmonic distortion The 3rd harmonic is perceived more easily and often is the BITE that is added to midrange and the warmth to the low freqs by tube gear Analog tape also saturates in this manner The 3rd harmonic is induced in the FATSO by increasing level thru the distortion circuits It is usually the result of flattening the tops and bottoms of waveforms Second harmonic is also added especially while compressing in the Fatso 10 of second harmonic can sometimes be hard to perceive We have provided distortion indicator
34. t Bruce Hornsbyish pianos are often real or samples of real pianos with medium attack and medium release that achieve a bite followed by sustained body If you find the Buss type compressor a bit gentle and too hot and distorting some of the peaks try the Tracking Compressor with a fast release etc The GP type compressor may work depending on how even the piano partis If you have a dense mix and really need to make it take up a finite spot in the mix go for the SPANK This will slap the dynamic range down smoothly and quickly It won t be an unfamiliar sound Old Beatle records started using drastic amounts of compression to keep a piano sitting inside a busy arrangement The saturator or soft clip part of the Fatso will be very useful also on piano and keys Pianos and synths can have quite a peaky transient and the instantaneous nature of the saturator can often give you 6 db more peak headroom before your ear detects clipping Synthesizers and samplers can benefit enormously since their envelope generators often create huge front peaks The Warmth is also very useful here since it can soften the edges and also take care of the sharp trebly plastic edge without affecting the low frequency amplitude Again watch over using the Warmth you will find subtle use of the Fatso on keys to be extremely pleasing once they are dropped back in the mix Often you can take a thin lifeless keyboard part and bring warmth and reality to it Drums without an
35. tack try the buss compressor to maintain transients Watch over warming guitars with the saturators and the warmth circuits Crunchy guitars which are full of harmonics are notoriously sensitive to tonal changes Over saturating or warming can take away the clarity or bite needed to cut thru Other times it s just what s needed to let the guitar be louder in a mix and stay out of the way of vocs because the upper spiky harmonics are flattened a bit When you are dealing with an occasional peaky guitar where certain chords or notes take your head off the dynamic action of the warmth control can be sooooo useful Don t overdue this though especially while tracking The Tranny may also actually seem to add midrange focus because of the harmonic generation on the low and low mid To smooth out solos try the tracking compressor with tranny and warmth REMEMBER TO SET UP COMPRESSOR FIRST The warmth really interacts with the compressor Plucked Instruments amp Acoustic Guitar Plucked instruments can benefit greatly from the Fatso s processing Back in 1998 the Fatso was taken to Greece and used on many very troublesome ethnic plucked instruments At Grammys a club in ATHENS some bizarre FATSO behavior was immediately noticed when the extremely transient acoustic instruments swamped several internal circuits The compressor needed a heavier knee with more sponge in the attack The tracking compressor green and yellow LEDs on was twe
36. xed Controls The Fatso uses a hardwired bypass relay enabling the user to compare processed and unprocessed signals accurately When comparing the original signal from the processed signal matching the output level with bypassed signal makes it very easy to hear the processing changes The bypass on the Fatso is multiplexed with the Tranny control so a double press is necessary while comparing the processed signal to input signal To change compressor types warmth ratio and the Tranny bypass press the associated button and cycle through the options These step function controls are sometimes inconvenient when trying to compare two settings but if it was the only way we could fit all the controls on a front panel without an LCD display It was very important to fit it all in the single height 1 75 cabinet The color encoded indicator LED s were arranged in an easy to read pattern with Red LED s usually indicating radical or distorted settings The trade off of stepped controls vs the small size and power of the Fatso seems well worth it fatso Pet Tricks 1 You can alter the standard thresholds of the Fatso by inserting a level control in the Insert point By turning the gain down there the threshold will move higher elevating operating distortion Adding gain there will lower the threshold and lower Distortion 2 It is also possible to sidechain process Take the Link Out of a unit go to an EQ and or preamp then return it to the L
37. y processing activated the saturator which is always inline will pack those peaks down smoothly giving you 3 6 dB more avg level Distortion indicator LEDs the O VU and the Pinned Red LED give you a good idea of what s going on On percussion peaks can lite up the RED Pinned LED without any nasty distortion if they are short enough Analog tape can not handle all the top end and will round out the sound as will the FATSO s warmth processor and saturator Don t use more than 5 10 dB of warmth on drums though or you are probably asking for a dull sound Try putting digitally recorded tambourines etc through the Fatso and listen to the difference That clacky front edge will become warm and easy to listen to like the old analog tape and vinyl Snares Kicks Toms If you don t want to lose the basic sound try setting the compressor to buss compressor first This is a very gentle slow compressor that will leave the transients untouched If there are areas with over eq d highs or unnatural transients get into the warmth processing On snares that have had 8 10K added and have some really overly dynamic hits 5 10 dB of warmth may fold the highs back attenuate them and smooth out the tonality Use the High Frequency saturation that the warmth control provides on Kick drums that have the occasional clacky hit The Tranny will be useful also If the Kick drum is too boomy or too thumpy without enough clarity the tranny will add some upper harmo
Download Pdf Manuals
Related Search