Owner`s Manual
Contents
1. and release DELETE while the message you want to delete is being played The system beeps once and continues with the next message If you want to check a message before you delete it you can press HEMOREPEAT to replay the message before deleting it When the system reaches the end of the last message the messages not deleted are renumbered and the Message Window displays the total number of messages remaining in memory Recording a Memo You can record a memo to be stored as an incoming message The memo can be up to three minutes long and will be played back with other messages 1 Press and hold WEMOREFAT After the beep speak toward the microphone 2 To stop recording release WEMOREPET 3 To play the memo press PAVSTOF When Memory is Full The system can record approximately 12 minutes of messages including your announcement for a total of up to 59 messages When memory is full or 59 messages have been recorded the Message Window flashes F Delete messages to make room for new ones When memory is full the system answers calls after 10 rings and sounds two beeps instead of your announcement REMOTE OPERATION Connect with the Ananering System 1 Dial your telephone number froma touch tone phone with a different telephone number 2 When the system answers enter your three digit Access Code during or after the announcement The system announces the number of messages then beeps twice2. call If you choose not to record an announcement the system answers with a prerecorded announcement Hello Please leave a message after the tone 1 Press and hold awwcskir The system beeps Speak toward the microphone normally from about nine inches away While you are recording the Message Window displays 2 To stop recording release ANNC SKIP The system automatically plays back your announcement To review your announcement press and release ANNC SKIP Turning the System On Off Use to turn the system on and off When the system is off the Message Window is blank Volume Control Use volume buttons and to adjust the volume of the system s speaker Press the top button to increase volume Press the bottom button to decrease volume The system beeps three times when you reach the maximum or minimum volume setting OPERATION Answering Calls When the system answers a call the caller hears the announcement you recorded followed by a beep After the beep the system begins recording your caller s message A caller can leave a message up to three minutes long If the message is longer than three minutes or if the caller is silent for more than seven seconds or if the system runs out of memory the system beeps once and hangs up Callers can skip over your announcement by pressing Message Window The Message Window displays the number of messages that have been recor
3. 15 99 11 29 AM oe ONE KEY REMOTE COMMANDS Play All Repeat Annc Play New Delete Stop Exit Skip o amp B stem vas OPER 0 Record emo SE ONE KEY REMOTE COMMANDS Play All Repeat Stop Exit Annc TWO KEY REMOTE COMMANDS Turn system off Delete all messages Review announcement Record announcement Room monitor End remote access call AT amp T 1717 WC_2ATT O e e 66 speak after beep press stop 9 8 press 8 to speak with someone in the room press to exit G4 9 oN Ae 8 J TWO KEY REMOTE COMMANDS Turn system off 0 Delete all messages 3 Review announcement 7 Record announcement 7 to Room monitor oJ End remote access call 1 15 99 11 29 AM HOE stop Speak after beep press 8 press 8 to speak with someone in the room press to exit G4 9 REUSED 1 15 99 Fold open this manual for information about this product s installation and operation Please read Part 1 Important Product Information included in this package Part2 1998 Lucent Technologies Consumer Products L P All rights reserved Printed in Mexico 848230009 Issue 3AT amp T AT amp T 1717 panels_3ATT INSTALLATION 1 Connect the telephone line cord Plug one end of the telephone line cord into the jack labeled TEL LINE on the back of the system Plug the other
4. GSKP until the correct hour is announced Then release the button Press and release C The current minutes setting is announced 6 To change the minutes setting hold down Or AWNGSKIP until the correct minutes setting is announced Then release the button 7 Press and release 0 The new day and time are announced To check the clock press and release a NOTE In the event of a power failure see the instructions on the bottom of the unit to reset the clock PLAY Light indicates mesages Recording Your Announcement Before using this answering system you should record the announcement up to one minute long that callers will hear when the system answers a call If you choose not to record an announcement the system answers with a prerecorded announcement Hello Please leave a message after the tone 1 Press and hold JP The system beeps Speak toward the microphone normally from about nine inches away While you are recording the Message Window displays 2 To stop recording release AINE The system automatically plays back your announcement To review your announcement press and release NESKA Tumming the System On Off Use MOF to turn the system on and off When the system is off the Message Window is blank Volume Control Use volume buttons 2 and to adjust the volume of the systems speaker Press the top button E to increase volume Press the bottom
5. If you don t hear the two beeps wait for the announcement to end or press F to stop the announcement then reenter the code 3 Thetwo beep signal lets you know the system is ready to accept a remote command Playing Messages 1 After the two beeps wait four seconds and the system plays back messages oR Press and release 7 to play all messages oR Press and release 2 to play only new messages If there are no new messages the system announces No new messages 2 To repeat a message Press and release G while the message is playing To repeat part of a message Hold down To resume playing release 2 To skip a message Press and release E while the message is playing To skip part of a message Hold down 6 To resume playing release 0 To stop message playback Press and release To save messages hang up Deleting Messages Delete All Messages After you have listened to all messages and heard the two beeps press Delete Selected Messages Press and release 3 while the message you want to delete is playing Record Announcement 1 Press 2 and begin speaking after the beep 2 Press E when you are finished The system replays your new announcement To review your announcement Press aoa Record a Memo 1 Press and begin speaking after the beep 2 Press 5 when you are finished Room Monitor with Intercom You
6. REVISED 1 15 99 Answering System _ with Time Day 1717 old open this manual for information about this product s installation and operation Please read Part 1 Important Product Information included in this package Part 2 1998 Lucent Technologies Cons Products L P All rights reserved Printed in Mexico 843230009 Issue 3AT amp T INSTALLATION Strain Telephone Relief Tab Set Cord Modular Telephone Jack Power Cord Telephone Line Cord 1 Connect the telephone line cord 3 Connect the power cord Plug one end of the telephone line Plug the power cord into the jack cord into the jack labeled TEL LINE labeled POWER and into an electrical on the back of the system Plug the outlet not controlled by a wall switch other end into amodular telephone Fit the power cord behind the strain jack relief tab The Message Window 2 Connect the telephone boe e al that you need to NOTE If you do not want to connect a l telephone skip to Step 3 A Use only the power cord supplied with this product If you need a Plug the telephone set cord from the telephone into the jack labeled TEL SET on the back of the system replacement call 1 800 722 9125 Input 120V 60 Hz Output 9V AC 400 mA fis iis OPERATION Set and hear time day Use with other buttons to change hear settings Turn system on or off Record a memo Repeat all or part of a message Setting the Clock
7. RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE DU RATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN EXCEPT AS PROVIDED HEREIN RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBIL ITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY INCLUDING BUT NOT LIMITED TO ANY DAMAGES RESULTING FROM INCONVENIENCE LOSS OF TIME DATA PROPERTY REVENUE OR PROFIT OR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Some states do not allow the limitations on how long an implied warranty lasts or the ex clusion of incidental or consequential damages so the above limitations or exclusions may not apply to you In the event of a product defect during the warranty period take the product and the Ra dioShack sales receipt as proof of purchase date to any RadioShack store RadioShack will at its option unless otherwise provided by law a correct the defect by product repair without charge for parts and labor b replace the product with one of the same or similar design or c refund the purchase price All replaced parts and products and products on which a refund is made become the property of Ra
8. TO If you have no messages the system announces No messages Play new messages only Hold down WSTOA for about two seconds until the system begins playing If you have no new messages the system announces No new messages Repeat entire message Press and release HEMOREPEAT Repeat part of message Hold down HENOREFAD for afew seconds then release it to resume playing The system beeps while the button is held down Repeat previous message Press MEMOREFEAT twice continue this process to hear other previous messages Skip to next message Press and release GNNCSKP Skip part of a message Hold down a for afew seconds then release it to resume playing The system beeps while the button is held down Stop message playback Press and AT amp T 1717 panels_3ATT Swing Messages The system automatically saves your messages if you do not delete them The system can save about 12 minutes of messages including your announcement for a total of up to 59 messages When memory is full you must delete some or all messages before new messages can be recorded Deleting Messages Delete all messages Hold down GELETE The system announces Messages deleted and permanently deletes messages The Message Window displays 0 If you haven t listened to all of the messages the system beeps five times and does not delete messages Delete selected messages Press
9. You ll need to set the clock so that it can announce the day and time that each message is received Press PLAYSTOP to exit Setting the Clock at any time 1 Press and hold until the Message Window displays C and the default day is announced 2 To change the day setting hold down MEMO REPEAT Or ANNC SKIP until the correct day is announced Then release the button 3 Press and release Crock The current hour setting is announced 4 To change the hour setting hold dow n MEMO REPEAT Or ANNC SKIP until the correct hour is announced Then release the button 5 Press and release Clock The current minutes setting is announced 6 To change the minutes setting hold dow n MEMO REPEAT Or ANNC SKIP Until the correct minutes setting is announced Then release the button 7 Press and release crock The new day and time are announced To check the clock press and release CLOCK NOTE In the event of a power failure see the instructions on the bottom of the unit to reset the clock Displays number of messages and other information Adjust volume Delete all or selected messages Record and play outgoing announcement Skip all or part of a message Microphone Play Stop messages PLAY Light indicates messages Recording Your Announcement Before using this answering system you should record the announcement up to one minute long that callers will hear when the system answers a
10. answers a Call or have it silent off on your end your caller will still hear an announcement 1 Press and hold SETUP After the Ring Select setting is announced continue to press and release until the system announces Monitor is on or off 2 Press and release ANNC SKIP Or MEMO REPEAT Saving Messages The system automatically saves your messages if you do not delete them The system can save about 12 minutes of messages including your announcement for a total of up to 59 messages When memory is full you must delete some or all messages before new messages can be recorded Deleting Messages Delete all messages Hold down until the system announces your selection 3 Press and release PLAYSTOP or SETUP to exit Listening to Your Messages As the system plays back messages the Message Window displays the number of the message playing Before playing each message the system announces the day and time the message was received After playing the last message the system announces End of messages Play all messages Press and release PLAY STOP If you have no messages the system announces No messages Play new messages only Hold down PlAvsTOP for about two seconds until the system begins playing If you have no new messages the system announces No new messages Repeat entire message Press and release MEMO REPEAT Repeat part of message Hold do
11. button to decrease volume The system beeps three times when you reach the maximum or minimum volume setting 1 15 99 1 40 PM OPERATION Arsnering Calls When the system answers a call the caller hears the announcement you recorded followed by a beep After the beep the system begins recording your caller s message A caller can leave a message up to three minutes long If the message is longer than three minutes or if the caller is silent for more than seven seconds or if the system runs out of memory the system beeps once and hangs up Callers can skip over your announcement by pressing f Message Window The Message Window displays the number of messages that have been recorded If there are more than nine messages recorded the Message Window alternately displays the two digits of the total number of messages recorded If the Message Window displays F then the memory is full and you ll need to delete messages before new ones can be recorded PLAY Light The PLAY Light blinks when you have new messages and remains steady when you have messages in memory that you ve already played The PLAY Light is off when there are no messages in memory Call Screening Intercept Set the system to answer calls and set the volume control so you can hear the caller s message If you choose not to hear the caller s message adjust the volume to the lowest setting The Message Window displays 0 If you decide to take
12. can call the answering system and listen to any activity in the room 1 Press to listen for 30 seconds 2 Ifyou wish you can press while the monitor is active to speak to someone in the room up to 30 seconds 3 Press again during intercom operation to return to listening only 4 Press E at any time to exit Room Monitor with Intercom Ending the Remote Access Cail Press E The system announces The machine will now hang up and disconnects the call Changing Remote Access Code 1 Press The system announces Enter new de 2 Enter your new Remote Access Code any number between 100 and 999 3 Ifavalid code is entered the system announces the new Remote Access Code If an invalid code is entered the system beeps five times rapidly then beeps twice Repeat Steps 1 and 2 REMOTE OPERATION Tum System Off Press 0 0 Tum System On When the system is off it answers after 10 rings announces The machine is off and beeps twice 1 Press to turn the system on 2 The system beeps twice and is ready to answer calls and record messages If the system beeps five times the memory is full Memory Full The system answers after 10 rings then announces Memory is full and beeps twice you must delete messages to make room for new ones 1 Enter the Remote Access Code after two beep signal 2 Listen to messages and delete some or all of them 3 Press J to
13. change the Remote Access Code to any three digit number from 100 to 999 1 Press and hold SETIP After the Ring Select setting is announced continue to press and release SETUP until the system announces the current Remote Access Code 2 Press and release NCSA or WEVOREET until the system announces the first digit you want 3 Press and release SETIP to select the announced digit 4 Repeat Steps 2 and 3 for the second and third digits of the code 5 Press LAYSTOA to exit oR Press SETUP to turn the Announcement Monitor on or off follow Steps 2 and 3 under Announcement Monitor OPERATION Announcement Monitor You can choose whether to hear the announcement when your system answers acall or have it silent off on your end your caller will still hear an announcement 1 Press and hold ETIP After the Ring Select setting is announced continue to press and release SETUP until the system announces Monitor ison or off 2 Press and release NSHP or HEWOREPEAT until the system announces your selection 3 Press and release FLAYSTOA or SETUP to exit Listening to Your Messages As the system plays back messages the Message Window displays the number of the message playing Before playing each message the system announces the day and time the message was received After playing the last message the system announces End of messages Play all messages Press and release CIS
14. ded If there are more than nine messages recorded the Message Window alternately displays the two digits of the total number of messages recorded If the Message Window displays F then the memory is full and you ll need to delete messages before new ones can be recorded PLAY Light The PLAY Light blinks when you have new messages and remains steady when you have messages in memory that you ve already played The PLAY Light is off when there are no messages in memory Call Screening Intercept Set the system to answer calls and set the volume control so you can hear the caller s message If you choose not to hear the caller s message adjust the volume to the lowest setting The Message Window displays 0 If you decide to take the call lift the handset of any telephone on the same line The system stops recording and resets to answer calls Feature Set Up You can set up one feature at a time as described below or you can set up a feature and then move on to set up another feature After you change one feature press and release until you hear the voice prompt for the next feature you want to change OR Press PLAY STOP to exit OR The system will time out after 30 seconds and save any changes already made Ring Select and Toll Saver Use Ring Select to choose how many times the line will ring before the system answers a Call Set for 2 4 or Toll Saver When you set the system for Toll Save
15. dioShack New or reconditioned parts and products may be used in the performance of warranty service Repaired or replaced parts and products are warranted for the remainder of the original warranty period You will be charged for repair or replacement of the product made after the expiration of the warranty period This warranty does not cover a damage or failure caused by or attributable to acts of God abuse accident misuse improper or abnormal usage failure to follow instructions improper installation or maintenance alteration lightning or other incidence of excess voltage or current b any repairs other than those provided by a RadioShack Authorized Service Facility c consumables such as fuses or batteries d cosmetic damage e transportation shipping or insurance costs or f costs of product removal installation set up service adjustment or reinstallation This warranty gives you specific legal rights and you may also have other rights which vary from state to state RadioShack Customer Relations Dept W 100 Throckmorton St Suite 600 Fort Worth TX 76102 We Service What We Sell
16. e If the system s memory fills up during a message the system stops recording and disconnects the call System Does Not Answer After Correct Number of Rings e If the Toll Saver feature is on the number of rings changes from four to two when you have new messages waiting e In some cases the system might be affected by the ringing system used by the local telephone company e If the system s memory is full or the system is off the system answers after 10 rings System Will Not Record Messages When memory is full and the Message Window displays F saved messages must be deleted before new messages can be recorded DIFFICULTY System Does Not Respond To Remote Commands e Make sure you are calling from a touch tone phone When you dial a number you should hear tones If you hear clicks instead the phone is not a touch tone telephone e The answering system may not detect the Remote Access Code while your announcement is playing Try waiting until the announcement is over before entering the code e There may be noise interference on the phone line you are using Press dial buttons firmly e Make sure you are entering your Remote Access Code correctly e You might be calling from a phone that sends tones too short for your answering system to detect Power Failure Recovery If the system is disconnected from AC power it will not operate Your announcement and messages are retained in memory during a power fail
17. e memo press PLAYSTOP When Memory is Full The system can record approximately 12 minutes of messages including your announcement for a total of up to 59 messages When memory is full or 59 messages have been recorded the Message Window flashes F Delete messages to make room for new ones When memory is full the system answers calls after 10 rings and sounds two beeps instead of your announcement fini REMOTE OPERATION Connect with the fatale System Dial your telephone number from a touch tone phone with a different telephone number 2 When the system answers enter your three digit Access Code during or after the announcement The system announces the number of messages then beeps twice If you don t hear the two beeps wait for the announcement to end or press to stop the announcement then re enter the code 3 The two beep signal lets you know the system is ready to accept aremote command Playing Messages After the two beeps wait four seconds and the system plays back messages OR Press and release 7 to play all messages OR Press and release 2 to play only new messages If there are no new messages the system announces No new messages 2 To repeat a message Press and release 4 while the message is playing To repeat part of a message Hold down To resume playing release 4 To skip a message Press and release 6 while the message is playin
18. end into a modular telephone jack 2 Connect the telephone NOTE If you do not want to connect a telephone skip to Sep 3 Plug the telephone set cord from the telephone into the jack labeled TEL SET on the back of the system Connect the power cord Plug the power cord into the jack labeled POWER and into an electrical outlet not controlled by a wall switch Fit the power cord behind the strain relief tab The Message Window flashes C to indicate that you need to set the clock Use only the power cord supplied with this product If you need a replacement call 1 800 722 9125 Input 120V 60 Hz Output 9V AC 400 ma OPERATION Record a memo Displays number of messages and other information Adjust volume Delete all or selected mesages Record and play outgoing announcement Sap all or part of a mesage Microphone Play Slop mesages Repeatall or part ofa mesage Setting the dock You ll need to set the clock so that it can announce the day and time that each message is received Press PLAYSTO to exit Setting the Clock at any time 1 Press and hold 61068 until the Message Window displays C and the default day is announced 2 To change the day setting hold down HEROREFEAD or MNCS until the correct day is announced Then release the button 3 Press and release 100K The current hour setting is announced 4 To change the hour setting hold down WEMOREFEAT or NN
19. g To skip part of a message Hold down To resume playing release 6 To stop message playback Press and release To save messages hang up Deleting Messages Delete All Messages After you have listened to all messages and heard the two beeps press 3 3 Delete Selected Messages Press and release 3 while the message you want to delete is playing Record Announcement 1 Press and begin speaking after the beep 2 Press 5 when you are finished The system replays your new announcement To review your announcement Press aw Record a Memo 1 Press and begin speaking after the beep 2 Press when you are finished Room Monitor with Intercom You can call the answering system and listen to any activity in the room 1 Press 9 8 to listen for 30 seconds 2 If you wish you can press 8 while the monitor is active to speak to someone in the room up to 30 seconds 3 Press again during intercom operation to return to listening only 4 Press at any time to exit Room Monitor with Intercom Ending the Remote Access Call Press amp The system announces The machine will now hang up and disconnects the call Changing Remote Access Code 1 Press 9 9 The system announces Enter new code 2 Enter your new Remote Access Code any number between 100 and 999 3 Ifa valid code is entered the system announces the new Remote Access Code If an inval
20. id code is entered the system beeps five times rapidly then beeps twice Repeat Steps 1 and 2 REMOTE OPERATION Turn System Off Press 0 0 Turn System On When the system is off it answers after 10 rings announces The machine is off and beeps twice 1 Press to turn the system on 2 The system beeps twice and is ready to answer calls and record messages If the system beeps five times the memory is full fii Memory Full The system answers after 10 rings then announces Memory is full and beeps twice you must delete messages to make room for new ones 1 Enter the Remote Access Code after two beep signal 2 Listen to messages and delete some or all of them 3 Press 0 to make sure your system is on before you hang up fis IN CASE OF If this answering system does not work properly try the following suggestions If you re still having difficulty call 1 800 722 9125 Message Window Is Blank e Make sure the power cord is securely connected to both the answering system and an electrical outlet not controlled by a wall switch e Press to make sure the system ison Messages Are Incomplete e The system can accept messages up to three minutes long If a caller leaves a very long message part of it might be lost when the system disconnects the call after three minutes e If the caller pauses for more than seven seconds the system stops recording and disconnects the call
21. make sure your system on before you hang up 1 15 99 1 40 PM IN CASE OF If this answering system does not work properly try the following suggestions If you re still having difficulty call 1800 722 9125 Message Window Is Blank Make sure the power cord is securely connected to both the answering system and an electrical outlet not controlled by a wall switch Press GIl0F to make sure the system ison Messages Are Incomplete The system can accept messages up to three minutes long If a caller leaves a very long message part of it might be lost when the system disconnects the call after three minutes If the caller pauses for more than seven seconds the system stops recording and disconnects the call If the system s memory fills up during a message the system stops recording and disconnects the call System Does Not Answer After Correct Number of Rings If theToll Saver feature is on the number of rings changes from four to two when you have new messages wating In some cases the system might be affected by the ringing system used by the local telephone company Ifthe system s memory is full or the system is off the system answers after 10 rings System Will Not Record Messages When memory is full and the Message Window displays F saved messages must be deleted before new messages can be recorded DIFFICULTY System Does Not Respond To Remote Commands Make s
22. r it answers after four rings when you have no new messages and after two rings when you have new messages 1 Press and hold for about two seconds The system announces the current ring selection 2 Press and release ANNC SKIP Or MEMO REPEAT until the system announces your ring selection 3 Press and release to exit OR Press and release to change the Remote Access Code follow Steps 2 5 under Remote Access Code Remote Access Code You can use many features of this answering system remotely from a touch tone phone Most features can be accessed only after you enter a Remote Access Code which is preset to 123 You can review the Remote Access Code by pressing and releasing SETUP You can change the Remote Access Code to any three digit number from 100 to 999 1 Press and hold SETUP After the Ring Select setting is announced continue to press and release until the system announces the current Remote Access Code 2 Press and release ANNC SKIP Or MEMO REPEAT until the system announces the first digit you want 3 Press and release to select the announced digit 4 Repeat Steps 2 and 3 for the second and third digits of the code 5 Press PLAYSTOP to exit OR Press to turn the Announcement Monitor on or off follow Steps 2 and 3 under Announcement Monitor OPERATION Announcement Monitor You can choose whether to hear the announcement when your system
23. the call lift the handset of any telephone on the same line The system stops recording and resets to answer calls Feature Set Up You can set up one feature at atime as described below or you can set up a feature and then move on to set up another feature After you change one feature press and release ETP until you hear the voice prompt for the next feature you want to change oOR Press PLAYSTO to exit oR The system will time out after 30 seconds and save any changes already made Ring Select and Toll Saver Use Ring Select to choose how many times the line will ring before the system answers a call Set for 2 4 or Toll Saver When you set the system for Toll Saver it answers after four rings when you have no new messages and after two rings when you have new messages 1 Press and hold ETIP for about two seconds The system announces the current ring selection 2 Press and release NNGSKE or MEMOREPEAT until the system announces your ring selection 3 Press and release PLAYSTOA to exit oR Press and release SETIF to change the Remote Access Code follow Steps 2 5 under Remote Access Code Remote Access Code You can use many features of this answering system remotely froma touch tone phone Most features can be accessed only after you enter a Remote Access Code which is preset to 123 You can review the Remote Access Code by pressing and releasing SETUP You can
24. ure but you will need to reset the clock See the instruction label on the bottom of the unit Message Window Displays C Clock needs to be reset Flashing System is busy or in use OR Steady System in Remote Access mode Remote listening mode m Deleting rotating BE Memory is full OR Announcement monitor is off shown during Setup m Call 1 800 722 9125 itt LYLVZ NSS EEQQEZ8Y8 02IX W U p Uld pansases S YBU d 7 S ONPOd JaWNSUOZ s lojouy214u22N7 BEI O Tapeless Digital Answering System 1717 Remote Commands To connect with your answering system 1 Dial your telephone number from a touch tone phone 2 When the system answers enter your Remote Access Code The system announces the number of messages and beeps twice 3 Wait four seconds for the system to play back all messages OR Enter a remote command from inside this card AT amp T 1717 WC_2ATT 1 LSLVZ NSS EEQ0EZ8Y8 021X W U PeqUlld pansasas S4 Y d 7 SPNPOId J UNSUOJ s H0jouy2 17U22N7 8661 O Tapeless Digital Answering System 1717 Remote Commands To connect with your answering system 1 Dial your telephone number from a touch tone phone 2 When the system answers enter your Remote Access Code The system announces the number of messages and beeps twice 3 Wait four seconds for the system to play back all messages OR Enter a remote command from inside this card 1
25. ure you are calling froma touch tone phone When you dial a number you should hear tones If you hear clicks instead the phone is not a touch tone telephone The answering system may not detect the Remote Access Code while your announcement is playing Try waiting until the announcement is over before entering the code There may be noise interference on the phone line you are using Press dial buttons firmly Make sure you are entering your Remote Access Code correctly You might be calling from a phone that sends tones too short for your answering system to detect Power Failure Recovery If the system is disconnected fromAC power it will not operate Your announcement and messages are retained in memory during a power failure but you will need to reset the clock See the instruction label on the bottom of the unit Message Window Displays F L Clock needs to be reset Hashing Systemis busy or in use OR Steady System in Remote Access mode r Remote listening mode 1 Deleting rotating F Memory is full or Announcement monitor is off shown during Setup E cal 1800 722 9125 fi Limited One Year Warranty This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one 1 year from the date of purchase from Ra dioShack company owned stores and authorized RadioShack franchisees and dealers EXCEPT AS PROVIDED HEREIN
26. wn for a few seconds then release it to resume playing The system beeps while the button is held down Repeat previous message Press twice continue this process to hear other previous messages Skip to next message Press and release ANNC SKIP Skip part of a message Hold down ANNG SKIP for a few seconds then release it to resume playing The system beeps while the button is held down Stop message playback Press and release PLAY STOP DELETE The system announces Messages deleted and permanently deletes messages The Message Window displays 0 If you haven t listened to all of the messages the system beeps five times and does not delete messages Delete selected messages Press and release while the message you want to delete is being played The system beeps once and continues with the next message If you want to check a message before you delete it you can press to replay the message before deleting it When the system reaches the end of the last message the messages not deleted are renumbered and the Message Window displays the total number of messages remaining in memory Recording a Memo You can record amemo to be stored as an incoming message The memo can be up to three minutes long and will be played back with other messages 1 Press and hold wemorrePear After the beep speak toward the microphone 2 To stop recording release MEMO REPEAT 3 To play th
Download Pdf Manuals
Related Search