PRODUCT FACT SHEET FM 3306 and FM 3316 Overview Features
Contents
1. 33V Transients will be clamped Page 3 of 5 www mixtelematics com EMC Directives EMC Tests m CE DIN EN 55022 09 2003 DIN EN 61000 6 2 03 2006 E1 ECE Regulation No 10 as last amended by Amendment 02 Supplement 2 12 08 2004 RS232 PORTS Maximum Speed 57600 Baud higher rates possible with hardware flow control Protection Transient 15kV as per human body model Protection DC 12V 12V Normal Operating Speed 38Kbits per second Maximum Supply Current lt 20mA CLK Protection Transient 15kV as per human body model Protection DC OV to 12V REAL TIME CLOCK Time Loss lt 10 Minutes per year typical lt 5 seconds when a GPS is used auto synchronization temperature change affects the accuracy of the RTC crystal it s most accurate at 25 C Battery Backup Life gt 5 Years typical at 30 to 70 C Channels 50 Update Rate 4Hz Horizontal Position lt 2 5m Accuracy Accuracy DGPS SBAS lt 2 0m Start up Time lt 2 Minutes GPRS Multi slot class 10 Quad Band 850 900 1800 1900 MHz Transmit Power Output power Class 4 2 W for EGSM850 Class 4 2 W for EGSM900 Class 1 1 W for GSM1800 Class 1 1 W for GSM1900 SIM Card 3V Page 4of 5 www mixtelematics com Auxiliary inputs outputs 8 Configurable Analogue or Digital Inputs 1 Frequency Input 1 Relay Drive Output 1 Positive Drive Output 1 Starter Interrupt 1 RS232 Serial Interface 1 TTL Serial Interfac2. TELEMATICS MOBILE INFORMATION EXCHANGE PRODUCT FACT SHEET FM 3306 and FM 3316 Overview The FM 3306 without backup battery and FM 3316 with backup battery collectively referred to herein as the FM 3316 is the ideal on board computer for the management of vehicle and driver performance driver safety and vehicle utilization The on board computer enables the fleet manager to remotely monitor the performance of a vehicle Data is recorded on a second by second basis with driver violations and detailed trip information being made available to the fleet manager in real time The FM 3316 on board computer interfaces directly with the vehicle s data bus supporting the CAN J1939 and J1708 J1587 standards Features Recording information from the vehicle s data bus has several benefits over the traditional way of recording vehicle data Where data is available up to 20 parameters may be monitored in real time installation of the unit does not require the connection of expensive 3rd party sensors installation is quicker more robust and the recorded data is more accurate CAN SUPPORT CAN Interface Standard The FM 3316 supports CAN J1939 and J1708 J1587 standards Vehicle Data Support When available on the vehicle s CAN bus the FM 3316 is capable of recording up to 20 CAN J1708 signals in real time Speed RPM fuel consumption fuel tank level PTO coolant level coolant temperature high Oil pressure hi
3. to sound when an event occurs Servicing amp Licensing Set reminders for your vehicle s next service or for your vehicle driver license expiry Backup Battery The FM 3316 is equipped with an internal Backup Battery offering an additional layer of security making tracking possible even if the vehicle s main battery has been disconnected The Backup Battery starts to operate as soon as the supply to the main vehicle battery is cut The FM 3306 does not include a Backup Battery www mixtelematics com Page 1 of 5 www mixtelematics com Moley wale ts Manage Locations Add any desired location such as customer supplier or no go zones Route Planning Plan routes by entering stops start times and duration of each stop This can serve as daily job activity sheets for your drivers Active Passive Tracking or Request the vehicle position in real time or view the route taken after the trip has been downloaded Active Trail Active Trail allows hourly updating of the Fleet Manager software with GPS vehicle positions GPS Data Recording A variety of positional information is recorded with every GPS point e g vehicle and driver ID date and time latitude and longitude altitude heading soeed number of satellites etc COMMUNICATION Downloading The GSM modem is used to download data from and upload data to the FM 3316 This allows for real from uploading to Vehicle time tracking and immediate active event notifications It is possible to up
4. are and new configurations and to download logged data and unit specific configuration information This bus can also be used to drive the FM Keypad which can be used for selecting driving reasons and allows the driver to make voice calls when used with the FM Voice Kit Intended to be used by devices designed to work on a bus The bus was specified to be a Multi Master type to enable other intelligent devices to optionally work as master relieving the FM 3316 of processing 2MB of flash 31kB of RAM 352kB is dedicated to storing firmware 312kB for event data 128KB for tacho data 384KB for buffering data Technical specifications ENVIRONMENT Temperature Circuit Protection SUPPLY FM 3316 Storage 5 to 35 C Operating 20 to 55 C Backup Battery Charge 0 45 C Backup Battery Discharging 20 to 50 C FM 3306 Storage 20 to 85 C Operating 20 to 70 C Conformal coating over the PCB and components excluding connectors Current RELAY CIRCUIT Operating lt 72mA at 28V typical Sleep lt 50mA at 28V typical Powered Down lt 3mA at 28V typical Operating lt 100mA at 12V typical Sleep lt 60mA at 12V typical Powered Down lt 2mA at 12V typical Firmware unit configuration GSM signal strength affect the current consumption Current consumption is higher during GPS lock acquisition Current Specifications Maximum Continuous Voltage on Pin Protection 200mA typical
5. e CAN Interface J1708 Interface 8 analogue or digital inputs can be configured to monitor any device that generates a change in voltage E g seat belts headlights refrigeration units temperature sensors emergency lights doors PTO UDS trailer coupling etc Voltages are measured in the range of 0 38 volts in steps of approximately 0 15 volts Inputs may be programmed to measure voltages between 0 and 5 volts in increments of approximately 0 02 volts The eighth input 18 is shared with the auxiliary frequency input F4 An auxiliary frequency input can be configured to monitor any device that generates a change in frequency e g liquid flow measurement or as a pulse counter e g electronic fuel consumption measurement EDM Frequencies of up to 150Hz can be measured or low board rate encoded RS232 inputs of up to 75 baud The auxiliary frequency input F4 is shared with the eighth input 18 The relay drive output can be used to drive a relay with a current consumption of up to 150 mA that can power a peripheral device on or off Positive Drive output is used to power external devices at 2V below battery voltage and can supply current up to 1A The FM 3316 has a dedicated starter interrupt A relay socket comes fitted to the main power harness for this purpose This can be connected to any RS232 serial device using the FM300 Serial Harness The FM Terminal can be connected using the FM300 Serial Harness The FM Tw
6. gh Oil level low clutch over load maximum axle weight brakes applied clutch engaged total engine hours vehicle odometer distance to next service TCO drive recognize TCO over speed and TCO direction indicator VEHICLE AND DRIVER MANAGEMENT Vehicle Access Control A driver tag code plug is used to identify and verify a driver An optional starter interrupt can be used to immobilize the vehicle until such time as the driver presents an authorised driver tag Trip Data Recording Standard recorded data includes Date and time Distance or hours Speed or hours RPM Power takeoff Fuel usage Trip start depart arrive end time Driver name and ID Vehicle ID Second to Second Tacho The status of speed and RPM is recorded every second This provides valuable in depth information for Data accident analysis Violation amp Event Standard event violations include Over speed Over revving RPM Over green band driving low and Monitoring high Harsh braking Rapid acceleration Excessive idling Overtime driving Power takeoff true or false Customizable Events Define additional custom events such as panic button pressed door open no go zone entered sudden impact warning lights activated refrigerator temperature exceeded etc Active Events Receive data messages when selected standard or user defined events occur e g a cargo door opening in a no go zone driver arrived at customer location Driver Warning A buzzer can be set
7. grade firmware or update the configuration remotely over the air using the GSM modem thus reducing the need to remove the vehicle from duty when performing maintenance Satellite Communication Satellite communication allows limited data download from and upload to the FM 3316 when using the optional FM Sat Comms transceiver This provides real time tracking and event monitoring when out of GSM coverage FM Sat Comms provides global coverage except at the extreme poles of the earth Voice Calls GSM voice communication is possible when using the optional FM Voice Kit which allows for hands free operation Wireless Communications The FM Wireless Kit allows data to be downloaded from or uploaded to the FM OBC Clients now have the option to make use of cheaper communication alternatives such as short range RF technologies like Wireless LAN The Wireless LAN functionality of the FM Communications Suite provides the equivalent functionality as that of communications over GPRS General information The FM300 Communicator includes GSM GPRS Antenna GPS Antenna Main harness with integrated buzzer includes the CAN interface wires in addition to conventional I O wires 2 x frequency inputs 3x digital analogue input FM300 code plug harness and socket Blue driver s plug driver log on FM on board computer user manual J1708 2 wire harness Optional harnesses serial harness voice harness I O harness 2x frequency inpu
8. in Serial Harness can be used to convert this to a standard RS232 port to connect a second serial device This can be connected to a J1939 CAN bus using the yellow green twisted wires on the main connector This can be connected to a J1708 bus using the separately supplied yellow blue twisted wire Page 5 of 5
9. t 5x digital analogue input ground and positive drive Technical description Voltage Range 9V DC 33V DC Input Protection Complies with 1SO7637 Part 1 and 2 Clock Real time with independent battery back up Firmware Re programmable firmware and configuration over wired and wireless media Ignition Input Used to monitor the ignition switch status I O Capabilities 8 digital analogue inputs 1 auxiliary frequency input 1 relay drive output 1 positive drive output 1 starter interrupt 1 RS232 serial interface 1 CAN interface 1 J1708 interface The eighth input 18 is shared with the auxiliary frequency input F4 Page 2 of 5 CAN J1708 Inputs Outputs amp Events Speed and RPM input filters Audio Interface Buzzer amp LED C Bus TTL Level Serial Port Memory Normal operating speed Maximum operating speed Normal operating speed Maximum operating speed www mixtelematics com 250Kbits per sec 1Mbits per sec 9600bits per sec 9600bits per sec Highly configurable inputs and events capable of output control Speed and RPM calibration sensitivity is configurable This interface allows the user to make voice calls using the optional FM Voice Kit FM Keypad and FM300 Voice Kit Harness Buzzer and LED are available to warn the driver and to provide feedback of the vehicle s status Intended for use with code plugs used to identify drivers calibrate diagnose faults upload firmw
Download Pdf Manuals
Related Search