Reflection VariWhite - User Manual ver. 1.0
Contents
1. BRIGHTNESS 1 100 8 6 User settings Mode The fixture permits three functional modes DMX MASTER and SLAVE It restores to DMX the functioning of the unit DMX only 16 English 8 7 Connecting DR1 and DR1 Plus All features are available in the menu can also be activated by DR1 code CO9707 and DR1 Plus cod CO9709 DR1 and DR1 Plus is a tool designed for technicians who can operate the apparatus at the same time the programmer of the show without having to physically intervene on headlamps but controlling functions remotely For example DR1 and DR1 Plus eliminates the need to change a DMX address on the unit thus avoiding the technical climbing on the structure and can read hours of lamp life and other functions normally accessible from the display DR1 and DR1 Plus also allows updating the firmware of the projectors To enable a projector to work with DR1 or DR1 Plus you must set each unit of the line with its own unique identity number ID WARNING lf you set as identification number 0 Reflection will not be recognized by DR1 and DR1 Plus Never assign the same ID to two or more units of a same DMX line This causes the failure of the system DR1 and DR1 Plus will display an error message For more information see the manual for DR1 or DR1 Plus 8 8 Electronic alignment of the leds The display panel of Reflection allows the electronic alignment of the leds this procedure is performed b2. to 7000 K without dmx SIGNAL ZOOM sa SAVE ALL stores all settings until next power on DIMMER STROBE See for visualization REFLECTION A001 STROBE 40 EE Save All DISABLE MAX On It disables the MAX alignment of the leds and sets them to CALIBRATION Off maximum value SILENCE fans and cooling pump work at minimum Silence AUTO the work of fans and pump are regulated by PCB in function FANS MODE CONTROL Auto of the temperature measured High It start the reset procedure of the zoom motor RESET enter Keep pressed ENTER and MENU buttons during reset to access to PECIAL MODE RECALL DEFAULT It restores all settings to the default settings with exception of SETTING lt lt Are vou sure alignments addressing and unit s hours counter It sets the ID number of the unit Use and buttons and ENTER to ID CODE Dalan confirm 14 English 8 4 Tests and measures Measures The internal microprocessor of Reflection allows for several diagnostic and output paramenter to be displayed lt shows temperature measured by the sensors in the unit TEMPERATURE Tboard Tled Tdriver Tsens It shows the values in Volt of the mains power the fans and pump Valim VOLTAGE Vrad Vfan Voump It shows the DMX value 0 255 received on each DMX channel used by DMX INPUT MEASURE the unit on the DMX chain Reading of the typical DMX value called RATE frequency of signal DMX RATE u
3. 2 3 EC norms The projector meets all fundamental applicable EC requirements 5 3 1 Technical characteristics English 3 Product specifications Power Maximum current 90 250 Vac 50 60Hz Autosensing 0 88 A 230 Vac 2 14 A 115Vac Power factor Cos q 0 94 Power 194 W Maximum room temperature 35 C 95 F Weight 12 5 Kg 27 5 lbs Grado di protezione IP20 The innovative core of Reflection consists of a reflection system with a source made of powerful leds in it which casts a compact beam in infinite colors combination without any defect that any other classic multi lens led projector gives Reflection has also an automatic zoom system that allows to modify the beam width 3 2 Dimensions 9921 uu 8Gp 371 mm 14 6 34 mm 1 33 325 mm 12 797 467 mm 18 38 Lezo uu 66 Lsz 9 uu 6G English 3 3 Unit s main components Components description 1 Yoke 6 Light source 2 Upper casing 7 Polycarbonate screen 3 Rear header and electronic sector 8 Yoke lock handle 4 Cooling sector 9 Lower casing 5 Mirror 4 Installation 4 1 Mechanical installation Reflection may be floor mounted or hung from an appropriate structure in any position If hanging the fixture from a lighting truss or similar we recommend the u
4. no functions LCD display off ed control ed control ed contro ed control ed control ed control ed control ed contro ed control LCD display on frequency tuning 100 frequency tuning 150 frequency tuning 200 frequency tuning 250 frequency tuning 300 frequency tuning 350 frequency tuning 400 frequency tuning 450 frequency tuning 500 control of zoom from narrow to wide beam Hz Hz Hz Hz Hz Hz Hz Hz Hz Table name DMX 512 function Date 30 08 2010 12 decimal 0 255 0 9 10 21 22 33 34 46 46 57 58 69 70 81 82 93 94 105 106 117 118 128 129 255 0 255 0 9 10 57 58 59 60 108 109 110 111 159 160 161 162 207 208 209 210 255 0 9 10 71 72 102 103 133 134 185 186 199 200 205 206 211 212 217 218 223 224 229 230 235 236 241 242 247 248 255 percentage 0 100 0 4 4 8 9 13 13 18 18 22 23 27 27 32 32 36 37 41 42 46 46 50 51 100 0 100 0 4 4 22 23 23 24 42 43 43 44 62 63 63 64 81 82 82 82 100 0 4 4 28 28 40 40 52 53 73 73 78 78 80 81 83 83 85 85 87 88 90 90 92 93 95 95 97 97 100 English English 8 Display panel functions By suitably using all the functions of Reflection which can be activated through its display panel it is possible to change some of the parameters and to add some functions Changing the preset settings made by Coemar can vary the functio
5. The initial configuration settings are faulty or have been loaded incorrectly The unit has loaded its default configuration Turn the unit off and on again and if the error persists it means that the Eeprom is defective Refer to your Coemar service center for the servicing The electronics of the unit found problems in loading data from Eeprom it does not load custom settings but default factory settings Contact your Coemar Service Center near you The unit is not receiving all the DMX channels necessary for its operation Check the DMX address and the DMX address control console operation Note that some controllers may not generate all 512 channels of signal DMX frame DMX signal present but frame too short the controller has not enough channels to control the projector The rear fan is damaged or stuck Turn off the unit then turn it on again and if the error persist contact your Internal FAN Coemar Service Center near you Radiator FAN The internal cooling fan is damaged or stuck Turn off the unit then turn it on again and if the error persist contact your Coemar Service Center near you Pump FAILURE The pump of the cooling system is damaged or stuck Turn off the unit then turn it on again and if the error persist contact your Coemar Service Center near you Over TEMPERATURE The light source has reached the maximum allowable temperature and so the unit shuts off Check for water level in the cooling cir
6. reset the display will blink for some seconas then will appear DMX addressing of the unit If the address continues to blink and the NO DMX SIGNAL message appears it means that the DMX signal has not been received Check the connection cable and the mixer functioning 7 1 DMX address of the unit Each projector uses 5 DMX channels for its complete operation and is controlled by a DMX 512 signal for further information see section 7 2 DMX functions DMX addressing When powered up initially each projector will show A001 which indicates DMX address 001 a projector thus addressed will respond to commands of channel 1 to 5 from your DMX 512 controller A second unit must be addressed as A006 a third one as A011 and so on The operation must be carried out on every Reflection which has an address different from A001 Altering DMX address 1 Press the or button until the display shows the required DMX address The digits on the display will blink to indicate that the variation has not been registered 2 Press the enter key to confirm your selection The digits on the display panel will cease to blink and the projector will now respond to the new address Note by holding the or button down the scrolling will be faster thus allowing a faster selection WARNING If you alter the DMX address with no DMX signal connected the digits on the display panel will continue to flash even after you have pressed ENTE
7. standards EN 61000 3 2 2006 Electromagnetic compatibility EMC Part 3 2 Limits Complete std A1 2009 A2 2009 current lt 16 A per phase EN 61000 3 3 2008 Electromagnetic compatibility EMC Part 3 3 Limits Complete std Limitation of voltage changes voltage fluctuations and Limits for harmonic current emissions equipment input flicker in public low voltage supply systems for equipment with rated current lt 16 A per phase and not subject to conditional connection EN 55103 1 Electromagnetic compatibility Product family standard for Complete std audio video audio visual and entertainment lighting control apparatus for professional use Part 1 Emission EN 55103 2 2009 Electromagnetic compatibility Product family standard for Complete std audio video audio visual and entertainment lighting control apparatus for professional use Part 2 Immunity EN 60950 1 2006 Information technology equipment Safety Part 1 Complete std A11 2006 General requirements EN 60065 2002 A1 2006 Audio video and similar electronic apparatus Safety Complete std A11 2008 requirements EN 60598 1 2008 Luminaires Part 1 General requirements and tests Complete std A11 2009 EN 60598 2 17 1989 Luminaires Part 2 Particular requirements Section 17 Complete std A2 1991 Luminaires for stage lighting television film and photographic s
8. the internal fans and heat exchanger must be perfectly clean 11 2 Special controls How to top up the water tank to perform every 1500 hours 1 Open the upper casing of the unit by unscrewing the 4 screws 2 Locate the water tank which is site in the back right of the unit beside the mirror 3 Remove the cap from the tank and fill it up to the edge with bi distilled water avoiding the formation of air bubbles 4 Close tight the tank s cap El WATER LEVEL WARNING 1 LIVELLO ACQUA Periodically check the water level in the expansion ia tank the tank must always be totally full BOLLA D ARIA Check that the cap is well tightened The lack of refrigerant can cause heavy damage to y the leds so to require their replacement 20 English Mechanical parts Check the correct working of the mechanical parts and if needed replace them Make sure the projector is not mechanically damaged If necessary replace the worn parts Electrical components Check all electrical connections in particular for correct grounding and correct attachment of all extractable connectors Press the connectors if necessary and reposition as before 11 3 Fuses Reflection has an automatic fuse that in most cases does not need to be replaced 12 F A Q and answers The following list shows common issues that may be simply solved If issues persist the unit must be repaired by qualified personnel or jus
9. R button to confirm the address 11 7 2 DMX functions To set the configuration access the menu MAIN FUNCTIONS DMX CHANNELS channel function type of control master i 1 dimmer proportional step 2 white tone proportional 3 zoom proportional step proportional step proportional step 4 strobe A proportional step proportional step proportional reset and 5 special step functions NOTE 1 channel 2 macros are available in conjunction with dimmer Fixture Reflection VariWhite Table number 295 Edition 0 adjust luminous output intensity from 0 to 100 select the primary WHITE color effect WHITE 7000 kK WHITE 6500 K WHITE 6000 kK WHITE 5500 K WHITE 5000 WHITE 4500 K WHITE 4000 k WHITE 3500 K WHITE 3200 K WHITE 3000 K adjust proportionally white color temperature from 3000 K to 7000 K proportional no effect variable speed strobing effect from slow to fast stop strobe sequenced pulse effect slow closing fast opening variable speed pulsing from slow to fast stop strobe sequenced pulse effect fast closing slow opening variable speed pulsing from slow to fast stop strobe random strobe effect with variable speed from slow to fast and synchronised colour temperature selected stop strobe random strobe effect with variable speed from slow to fast and non synchronised colour temperature park no functions no functions reset
10. Reflection variwnite instruction manual manuale di istruzioni Version 1 0 DIS133 0 coenmar Reflection variwnite Serial number numero di serie Date of purchase data di acquisto Retailer fornitore Address indirizzo Suburb cap citta Capital city provincial State stato Tel fax Please note in the space provided above the relative service information of the model and the retailer from whom you purchased your Reflection this information will assist us in providing spare parts repairs or in answering any technical enquiries with the utmost speed and accuracy Prendete nota nello spazio apposite dei dati relative al Modello e al rivenditore del vostro Reflection questi dati ci permetteranno di assistervi con la massima rapidit e precisione WARNING the security of the fixture is granted only if these instructions are strictly followed therefore it is absolutely necessary to keep this manual ATTENZIONE la sicurezza dell apparecchio garantita solo con l uso appropriato delle presenti istruzioni pertanto necessario conservarle User Manual Version 1 0 edition January 2011 English Index liPackaging and transportationi l aaa ea devas lee ae 5 A o A a a I cousin EA RIA ANIA PN ZA ceeines cnet amps ee ats 5 AC A A 5 2 General IOMA Cia 5 2 1 lmportant safety information tsan anen aeania atte rara ria 5 22 Waranty CONGITIONS til 5 AED a e eC nolo I all Ot E e Aso dicano e o deal o de
11. ariWhite result in conformity with the essential requirements as mentioned from the following EU Directives comprise all applicable amendments 2004 108 EC 2006 95 EC 2002 95 EC 2002 96 EC amp 2003 108 EC Directive of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to Electromagnetic Compatibility and repealing Directive 89 336 EEC EMC Directive of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits LVD Directive of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS Directive of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipments WEEE and that are applied all standards or technical specifications mentioned below Last two numbers of the Year in which is affixed the CE label 11 CE TCF reference nr PC10001A003 PC10001A004 PC10001A005 Place amp Date February 28 2011 Name and position Wilkinson Eric Managing Director Sign Da Page 1 of 2 DECLARATION OF CONFORMITY No 2011 013 Reference to standards and or technical specifications or part of them used for this Declaration of Conformity Harmonized
12. ation to suit any frequency or voltage within this range 5 2 Connection to mains power Mains cable characteristics The mains cable provided is thermally resistant complying to the most recent International standards Note in case of cable replacement similar cable with comparable thermal resistant qualities must be used exclusively cable 3 X 1 5 y external 10 mm rated 300 500V tested to 2 KV operating temperature 40 C 180 C Coemar cod CV5311 Connection to mains power Reflection is equipped with two power connectors one as input and one as output which can be used to connect more fixtures in series no more than 16 units 230V or 8 units 115V The max absorption of Reflection is reported in the following table 230 240V 0 88 A constant during normal exercise 100 115V 2 14 A constant during normal exercise WARNING Never link more than 16 units at 230 V or 8 units at 115 V English In the following figure you can see an example of series connection ae i Max 16 units 230Vac 8 units 115 Vac WARNING The use of a thermal magnetic circuit breaker is recommended Strict adherence to regulatory norms is strongly recommended Reflection should not be powered through a dimmer as this may damage the internal switching power supply Prior to connecting the device to mains power ensure that the mains characteristics are within t
13. cuit check fans and pump s functioning 10 Accessories and spare parts Reflection is a very versatile fixture optional accessories for its customization are available under request Coemar order code Description C0002 4 blades barndoor BC10001A000 accessories holder CO001 Standard size gel frame All the components of Reflection are available as spare parts from your Coemar dealer or Service Accurate description of the fixture model number and type will assist us in providing for your requirements in an efficient and effective manner 19 English 10 1 How to fix the optional accessories holder 1 Open the upper casing of the unit by unscrewing the 4 screws temporary remove the two side plates A 2 Insert the gel frame holder in site as explained in the picture and fix again the two plates A 3 Close the unit by repeating to the contrary the step 1 of this procedure 11 Maintenance 11 1 Periodic clearing Polycarbonate screen Even a fine layer of dust can reduce the luminous output and alter the compactness of the beam Regularly clean all filters and lenses using a soft cotton cloth dampened with a specialist lens cleaning solution Cleaning of the unit Use a soft brush or a common vacuum cleaner or a source of compressed air for removing dust For the cleaning of the housing use a soft cloth and a non aggressive cleaner Check that
14. ed position or in areas of extreme humidity Safety 1 The projector must always be installed with bolts clamps or other fixing devices which are suitably rated to support the weight of the projector 2 Always use a secondary safety fixing device with chain or steel wire of a suitable rating to sustain the weight of the unit in case of failure of the principal fixing point 3 The external surfaces of the unit at various points may reach 60 C Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off 4 Never install the fixture in an enclosed area lacking sufficient air flow the room temperature must not exceed 35 C 5 The projector contains electronic and electrical components which must under no circumstances be in contact with water oil or any other liquid Failure to do so will compromise the proper functioning of the projector 2 2 Warranty conditions 1 The fixture is guaranteed for a period of 12 months from the date of purchase against manufacturing or materials defects 2 The warranty does not extend to damage caused by inappropriate usage use by inexperienced operators or inadequate maintenance 3 The warranty is immediately void if the projector has been tampered or opened by unauthorized personnel 4 The warranty does not extend to fixture replacement 5 Both the serial number and the model of the projector are required for any advice or service from your authorised service centre
15. he recommended range for use with Reflection e All cabling and connections should be carried out by suitably qualified personnel 6 Control signal connections 6 1 Control signal connection by XLR5 plugs The digital control signal is transmitted to the projector via a two pole cable screened as per International standards for the transmission of DMX 512 data The connection must be serial using connectors XL5 male and female located on the back of Reflection labelled DMX512 IN e OUT see diagram Pin 1 GROUND Pin 2 DATA Pin 3 DATA Pin 4 nc Pin 5 nc English WARNING Make sure that screening and conductors are not in contact one another or with the metal housing of the connector Pin 1 and housing never must be connected to the power supply unit 7 Turning on the projector After having followed the preceding steps described proceed with the power supply and turn on the projector connecting it to the mains power The software version installed on the internal microprocessors will be shown on the display Reflection then will promptly start the reset procedure the operation will take some seconds allowing the correct positioning of the motor At the end of the procedure the display will stop blinking and will show the current DMX addressing gt DMX ADDRESS PLEASE WAIT During
16. iii 5 3 Product specifications ill ici o eee ALII aa 6 3 1 Technical characteristiosi c i ada iaia a eee 6 3 2 Dimensionsi ipallariaabaii pianali iia rsa ira agi 6 3 3 Unit isimain components r snella earlier 7 4 Installation iter hello ie eee 7 4 1Mechanical installation ili iv iaia a ia lia 7 4 2 Safetyichailic tag aaa ea alieni ia 8 4 3 Aqjusting unitStiltz saco natia di 9 NEI PERE RIE III 9 5 Operating voltage and tre qUENCY citas iaia aos aio iaia 9 5 2 Connection to MANS POWs ii A A A A aparin 9 6 Gontrol signal connections a a a a leia ig 10 6 1 Control signal connection by XLR5 plUYS coooococconoccconocononcnonanononcnnno conan ccoo corn cananea nena rene rra ran Kea pa TARS ua CE 10 7 Turning on the profector iit aaa lean aeree iii palla 11 71 DMX address of the unit ae a a aa 11 7 2 DMX functions a A At sleale en reali 12 9 Display panel TUNCH ONS lt o cis a A A aaa 13 8 1 Quick QUIETO MON iia A a A AAA A ed ec 13 8 2 Rapid counti s sails o ei Said ei ai 13 8 3 Main function menu Main functions i 14 8 4 Tests and measures Measures ciss ciccsascaacssdecasdeacseccasadzcadacnaseiacasdasagdanassagechassndceaersaceasdacasdeaasceqasaacabasascaeessdecapashesdeaesagacabact 15 8 5 Display settings Display SUP ovni a aaa 16 8 6 User settings Mode ritiri is ee eee lai isla ed pala 16 8 7 Connecting DRI and DR PPIUS iiine iii eval ede er io e i 17 8 8 E
17. lectronic alignment of the leds sii isisisi diiit ia ra alal alia 17 9 Error messages lira aan o aaa bai 19 10 Accessories anidspare parts e ia ai 19 10 1 How to fix the optional accessories holder iii 20 11 Maintenance ea Lala a Enna sila ii 20 Ale ts Periodic Clearing a EE lione iaia ilaria iii 20 11 2 Specialicontro Sita iii ele oe a ee i i 20 VALBUENA A Lasa 21 A AS O A O E 21 English Congratulations on having purchased a Coemar product You have assured yourself of a fixture of the highest quality both in the componentry and in the technology used We renew our invitation to you to complete the service information form on the previous page This will assist in providing prompt and accurate advice from your Coemar service centre which you can thoroughly trust and to which you can submit any requests for service or information Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to come 1 Packaging and transportation 1 1 Packaging Open the packaging and make sure that no part of the equipment has suffered any damage during the transportation In case of damage to the fixture contact your currier and your supplier immediately by telephone fax or email and inform them you will formally notify them in writing through registered letter Packing List Make sure the packaging contains 1 Reflection 2 This ins
18. mum intensity ZOOM Zoom motor alignment EXIT It stores the settings and exits from the procedure SPECIAL FUNCTIONS It allows to rest the hours meter of the led module also viewable in MEASURES menu It should be WORKING TIME RESET lt lt Are you sure gt gt reset whenever the led module has been replaced in order to give precise information on the duration lt makes the unit ready for the storing of the DOWNLOAD lt lt Are you sure gt gt f he PC lt makes the unit ready to receive the software UPLOAD lt lt Are you sure gt gt f he PC Nota Simultaneously pressing and buttons will return the calibration value to 128 default UPLD Function Upload this function allows to upgrade the firmware of Reflection only by DR1 or DR1 Plus and a Personal Computer Read DR1 or DR1 Plus manual for further information DULD Function Download this function allows to download the software from Reflection only by DR1 or DR1 Plus and by a Personal Computer Read DR1 or DR1 Plus manual for further information 18 English 9 Error messages If a malfunction occurs Reflection has a self diagnostic system that will show the error message on the display The following table will explain in detail the most common errors If despite of suggested intervention the problem persists call the Coemar Service center near you Error message Description and suggested solution Eeprom Failure CFG data Failure
19. ns of the projector so that it will respond differently to the controller therefore carefully read about the functions described here before carrying out any possible selection 8 1 Quick guide to men In order to access the functions just press the menu button one after the other all the voices of the menu will be cyclically shown each time the key or will be pressed To select the desired function press enter 8 2 Rapid count By the display panel of Reflection It is possible to quickly change the various numbers displayed for the different functions in the following 3 manners 1 Pressing the or buttons will cause the count to be quicker 2 Pressing first and then and then holding them down simultaneously will cause the numbers to jump to the highest value 3 Pressing first and then and then holding them down simultaneously will cause the numbers to jump to the lowest value 13 English 8 3 Main function menu Main functions The projector gives the opportunity to change and customize some functional settings MAIN FUNCTIONS TUNGSTEN Dimmer behavior it simulates dimmer effect with tungsten DIMMER SETTING XENON lamp or Xenon lamp REFLECTION A001 REFLECTION A001 REFLECTION A001 WHITE TEMPERATURE VARIWHITE 7000K VARIWHITE 6500 K VARIWHITE 3200K A LLL LLL BEN A000000000 REFLECTION A001 DIMMER 80 i It allows to vary white color temperature in several tones from REFLECTION A001 3000
20. pdating in milliseconds ALARM STATUS It shows the error message of the alarm in progress DIMMER 100 CH1 80 CH2 30 lt shows the luminous efficiency of the leds CH3 10 CH4 100 LED STATUS It shows the led s emission frequency It may be useful if frequency must LED FREQUENCY be set due to flicker issues It shows the led s life values in hours led life r led module life USAGE HOURS resettable led life life of total modules installed on the unit since now not resettable unit life life of the projector It shows the actual software version installed on the unit sw master SOFTWARE VERSION Reflection English 8 5 Display settings Display Setup The fixture allows to set the display visualization preferences DISPLAY SETUP Standard It allows to turn 180 the reading of the display if the unit is hanged DISPLAY REVERSE Beverse upside down It allows visualization in negative or in positive of the display graphics BACKGROUND Standard COLOR Reverse It allows one to decide number of seconds before turning off the display DISPLAY TIME OUT o ee ae light in case of inactivity OFF value leaves the backlight always OFF It allows setting up number of seconds buttons must be pressed in E order to activate functions This function avoid activation of features if BUTTON TIME OUT n sec buttons are pressed accidentally It allows setting of brightness of display back light
21. se of an appropriate clamp B as shown in the following diagram English WARNING Always ensure that your support structure and fixing bolts clamps etc are rated to support the weight of the fixture Floor installation If the fixture is floor mounted we recommend the using of the standard yoke which can be opened for allow an adequate support for the floor 4 2 Safety chain When hanging Reflection we recommend the use of a safety chain affine to the body and to the suspension device The safety chain should be either a metal rope or a metal chain both suitably for the purpose In the case that the chain used is not produced by Coemar ensure that it can bear the weight of the whole unit English 4 3 Adjusting unit s tilt In order to adjust the tilt of the unit laying on the floor or hanged on a truss simply loose the side handle adjust the tilt and lock the yoke again by tightening the handle again WARNING The unit never should be used upside down the arrows printed on the back of the unit indicate its upper side do not use the unit if the arrows aim downwards The unit allows an excursion angle of 150 5 Powering up 5 1 Operating voltage and frequency The unit may operates at voltages ranges from 90 to 250VaC at a frequency of 50 or 60 Hz It is not needed to effect any setup procedures Reflection will automatically adjust its oper
22. t contact your Coemar service near you Question Reflection does not power on Reflection does not answer to DMX signal Possible cause Projector not powered on DMX signal may not reach Reflection Suggested solution 1 Make sure the power cord is plugged in or test the input voltage Inspect the cable connection correct poor connections or inefficient repair or replace damaged cables Check DMX address of the unit Reflection is not recognized by DR1 Plus ID set to 0 or another unit in the chain is set with the same number Set an ID number different from 0 and from any other unit in the chain Information on disposal of the equipment The equipment at the end of its useful life must be disposed of at an appropriate recycling center for waste electrical and electronic equipment The treatment and disposal of environmentally friendly helps prevent potential negative environmental and health and promote the reuse and or recycling of materials making up the equipment Illegal disposal by the user includes the application of administrative sanctions provided by law 21 IR DL TA D 4 Sa SU DECLARATION OF CONFORMITY No 2011 013 The undersigned as representant of the following manufacturer Manufacturer identification Address COEMAR S p A Via Inghilterra Z I Est 46042 Castel Goffredo MN Italy declares that the following product Reflection V
23. truction manual 3 main power plugs 1 2 Trasportation Reflection must be transported exclusively in its original packaging or in an appropriate flight case 2 General information 2 1 Important safety information Fire prevention 1 Never locate the fixture on any flammable surface 2 Minimum distance from flammable materials 0 5m 3 Minimum distance from the closet illuminable surface 0 5m 4 Replace any blown or damaged fuse only with those of identical values Refer to the schematic diagram if there is any doubt 5 Connect the projector to mains power protected by a thermal magnetic circuit breaker Preventing from electric shock 1 Presence of high voltage inside of the fixture Insulate the projector from mains supply before opening or performing any function which involves touching the inside of the fixture including lamp replacement 2 For the connection to the mains adhere strictly to the guidelines outlined in this manual 3 The level of technology of Reflection requires the use of specialised personnel for all service applications refer all work to your authorised Coemar service centre 4 A good earth connection is essential for the proper functioning of the projector Never connect the fixture if there is no earth connection 5 Mains cables must not come into contact with other cables 6 Do not operate the projector with wet hands or in an area where water is present 7 The fixture must never be located in an expos
24. tudios outdoor and indoor EN 62471 2008 Photobiological safety of lamps and lamp systems Complete std other standards and or technical specifications IEC Guide 112 2000 04 Guide on the safety of multimedia equipment Complete std EN 62493 2010 03 Assessment of lighting equipment related to human Complete std exposure to electromagnetic fields Other technical solution detailed in the technical documentation or Tecnical Construction Folder 1 If appropriate shall specify the parts or articles the harmonized standard 2 lf appropriate shall specify the parts or articles the standard or technical specification Page 2 of 2 CE Coemar s p a via Inghilterra 2 A 46042 Castel Goffredo Mantova Italy ph 39 0376 77521 fax 39 0376 780657 info coemar com Coemar si riserva il diritto di apportare modifiche senza preavviso Coemar reserves the right to effect modifications without notification
25. y Coemar at the time of testing this procedure may be useful for special effects or in case of replacement of internal components PCBs leds etc Altering the settings made by Coemar may radically alter the functioning of the projector s functions Carefully read the following prior to attempting any changes WARNING This chapter should be considered for the exclusive use of technicians and highly skilled staff To access alignment function Activate the reset holding down the MENU and ENTER for at least 10 seconds Screen is then displayed SPECIAL MODE WARNING The electronic alignment procedure is only possible with DMX512 signal 17 English See the following diagram to enter in the function s details WARNING SPECIAL MODE This function is available only with DMX signal connected and by perform the reset while keep pressed ENTER and MENU buttons together for about 10 seconds LED and MOTOR ADJUSTMENT min Channel 1 Channel 1 leds alignment at minimum intensity min Channel 2 Channel 2 leds alignment at minimum intensity min Channel 3 Channel 3 leds alignment at minimum intensity min Channel 4 Channel 4leds alignment at minimum intensity max Channel 1 Channel 1 leds alignment at maximum intensity max Channel 2 Channel 2 leds alignment at maximum intensity max Channel 3 Channel 3 leds alignment at maximum intensity max Channel 4 Channel 4 leds alignment at maxi
Download Pdf Manuals
Related Search