Installation Guide
Contents
1. Bantam Installation Guide Part No 875 0265 000 Rev B1 Hemisphere This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Copyright Notice Hemisphere GPS Precision GPS Applications Copyright Hemisphere GPS 2011 All rights reserved No part of this manual may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of Hemisphere GPS Trademarks Hemisphere GPS the Hemisphere GPS logo A100 A20 A21 A2207M A221TM A30 A31 M A42IM A52 AerialACE AirStar AirTrac AutoMate M Bantam BaseLineHD BaseLineX BEELINE COAST Contour Lock Crescent Earthworks Eclipse e Dif eDrive eDriveTC eDriveVSi M eDriveX FliteTrac G100 GateMate GPSteer H102 HO IntelliFlow IntelliGate IntelliStar IntelliTrac Just Let Go L Dif LiteStar II LV101 LX 1 LX 2 M3 MapStar MBX 4 miniEclipse Outback Outback 360 Outback Guidance Center Outback Guidance Outback H2. Notwithstanding the foregoing either party may apply to any court of competent jurisdiction for injunctive relief APPLICABLE LAW This Agreement shall be governed by the laws of the Province of Alberta Canada exclusive of any of its choice of law and conflicts of law jurisprudence CISG The United Nations Convention on Contracts for the International Sale of Goods will not apply to this Agreement or any transaction hereunder GENERAL This is the entire agreement between Licensee and Hemisphere relating to the Product and Licensee s use of the same and supersedes all prior collateral or contemporaneous oral or written representations warranties or agreements regarding the same No amendment to or modification of this Agreement will be binding unless in writing and signed by duly authorized representatives of the parties Any and all terms and conditions set out in any correspondence between the parties or set out in a purchase order which are different from or in addition to the terms and conditions set forth herein shall have no application and no written notice of same shall be required In the event that one or more of the provisions of this Agreement is found to be illegal or unenforceable this Agreement shall not be rendered inoperative but the remaining provisions shall continue in full force and effect Warranty Notice COVERED PRODUCTS This warranty covers all products manufactured by Hemisphere GPS and purchased by the end purcha
3. mounting location 11 lights control panel 7 screen 23 PN 875 0265 000 Rev B1 Index list cables 3 parts 2 M M button 7 screen 23 menu 7 screen 23 mounting 7 touchscreen 8 7 touchscreen kit 7 8 4 touchscreen 9 8 4 touchscreen kit 9 antenna 14 antenna location 14 CPU 6 lightbar 11 lightbar kit 11 lightbar location 11 power panel 10 power panel location 10 mouse connecting 18 P parts cables listed 3 kits listed 3 list 2 planning installation 4 power 8 4 screen 22 green light 7 screen 23 panel mounting 10 panel mounting location 10 powering CPU and screens 22 switch 7 screen 23 power cable about introduction 19 connecting 19 power switching system on and off 25 S S button 7 screen 23 seven see 7 touchscreen shutting down 25 switches and kits parts list 3 T touchscreen calibrating 24 mounting general 6 powering 22 U up and down arrows 7 screen 23 USB Bantam Installation Guide 28 extension cable using 20 flash drive connecting to the CPU 20 inserting and removing 22 V video VGA cable connecting 18 Ww warnings antenna cable 16 cable connections 16 weight of components 4 PN 875 0265 000 Rev B1 End User License Agreement IMPORTANT This is an agreement the Agreement between you the end purchaser Licensee and Hemisphere GPS Inc Hemisphere which permits Licensee to use the Hemisphere software the Software that acc
4. on page 19 provides power to the CPU and to the touchscreen but slightly differently for each screen size When the panel lever switch is turned on o The 7 screen is powered directly even though it has its own power button e The 8 4 screen is not powered directly you have to press its own power button Once both screens are on you can turn them off and on with their own power buttons as long as the panel lever switch is on Turning the CPU and Screens On Turn on the vehicle s main power source vehicle battery generator other and set the ON OFF lever switch on the power panel to ON This powers up all components except the 8 4 touchscreen For the 8 4 touchscreen only then also press the power button on the front control panel Power 8 4 BECHER Le oy n When the system is powered up it will start the Window based AirTrac software Note Refer to the AirTrac User Guide for detailed descriptions of the software features and step by step instructions on how to use them for basic and advanced operations Inserting and Removing the USB Flash Drive The Bantam system comes with a 2GB USB flash drive for logging and for transferring files It also comes with an extension cable so you can access a USB port in the CPU remotely the CPU has two USB ports one each side That is you can plug the extension cable part of the USB kit part number 710 0087 000 into either CPU USB port and run the cable up to a conveni
5. AirTrac Quick Reference Guide 875 0136 001 A21 L Band antenna with mounting template 804 3036 0004 EN Color touchscreen 7 380 0016 000 or Color touchscreen 8 4 806 3015 000 Lightbar V1 806 2011 03A Lightbar cable 051 0022 001 Bantam Installation Guide 2 PN 875 0265 000 Rev B1 Chapter 1 Getting Started Table 1 2 Bantam parts list switches and kits Warranty statement 875 0066 001 Push switch for use with GPIO cable 051 0244 000 see 075 4002 000 Table 1 3 This is the optional swath advance switch Lever switch for use with GPIO cable 051 0244 000 see 075 4001 000 Table 1 3 This is the spray on off switch Lightbar mounting kit See The Lightbar Mounting Kit 710 0029 002 on page 11 MapStar kit CD and MapStar User Guide 710 0021 007 USB kit extension cable USB connector USB flash 710 0087 000 drive See Inserting and Removing the USB Flash Drive on page 22 Mounting kit 7 touchscreen mounting plates with 710 0096 000 mounting template See Mounting the 7 Touchscreen on page 8 or Mounting kit 8 4 touchscreen ball sockets and arm 604 0013 000 mount See Mounting the 8 4 Touchscreen on page 9 2GB USB flash drive spare 750 1083 000 Table 1 3 Bantam parts list cables Component Part Number Lightbar cable CPU to lightbar 051 0022 001 Video cable CPU to touchscreen 051 0243 000 GPIO cable CPU to o
6. Support 8444 N 90th St Suite 130 Scottsdale AZ 85258 USA Phone 480 348 9919 Fax 480 348 6370 afay hemispheregps com Documentation Feedback Hemisphere GPS is committed to the quality and continuous improvement of our products and services We urge you to provide Hemisphere GPS with any feedback regarding this guide by writing to the following email address DocFeedback hemispheregps com Contents Chapter 1 Chapter 2 Chapter 3 Chapter 4 Getting Started 52 26 23 93 x ai EX 1 Paris LIST S sns wea oa san qr ema bak ac qe dee tutem a adeant 2 Compohent Welghis x3 ca pop oti mara tb OU obsa afe de Eds 4 Planning the Installation cnin s a dd E ie dod je numm ERU 4 Mounting the Components 5 CPU ada ace dotes Meu dots naar tak ate adt ir warst dat dod an ais 6 Eee DMERREREREELARRSTLCDTRILAIDUTIEKT 6 The 7 Touchscreen Mounting Kit 7 Mounting the 7 Touchscreen 0 000 ces 8 The 8 4 Touchscreen Mounting Kit eae 9 Mounting the 8 4 Touchscreen else 9 F OWerlFatnel d niea educ o quema queer ed dus Bin dee ens dee en 10 Power Panel Mounting Location lus 10 Mounting the Power Panel 0 000 e eee eee 10 GONDA sco esto EE ce ee ba IESU Dene ea ee Saar 11 Lightbar Mounting Location 0 000 eee eee eee 11 The Lightbar Mounting Kit llle 11 Mounting the Lightbar llle 11 AMENN Soia dt aieo edt doy Coi Sod de erat is
7. any obligation to notify supply or install any improvements or alterations to existing Products GOVERNING LAW This agreement and any disputes relating to concerning or based upon the Product shall be governed by and interpreted in accordance with the laws of the State of Arizona OBTAINING WARRANTY SERVICE In order to obtain warranty service the end purchaser must bring the Product to a Hemisphere GPS approved service center along with the end purchaser s proof of purchase Hemisphere GPS does not warrant claims asserted after the end of the warranty period For any questions regarding warranty service or to obtain information regarding the location of any of Hemisphere GPS approved service center contact Hemisphere GPS at the following address Hemisphere GPS 8444 N 90th Street Suite 130 Scottsdale AZ 85258 Phone 480 348 9919 Fax 480 348 6370 ground 9 hemispheregps com www hemispheregps com 3 7 i Hemisphere EZS SSS a www hemispheregps com
8. brakes Air conditioners e Starter relays o Electric pump relays To eliminate CEME install diodes at the relays and solenoids that cause the CEMF and at the power supply cable connection of the SLX system Use a 47 V 5 W Zener Diode 1N5368 or equivalent Bantam Installation Guide 19 PN 875 0265 000 Rev B1 Connecting the USB Extension Cable To enable you to easily connect the USB flash drive to one of the CPU s side USB ports kit part number 710 0087 000 includes an extension cable Connect the extension cable to either USB side port on the CPU then using the connector adaptor connect the USB flash drive to the extension cable See also Inserting and Removing the USB Flash Drive on page 22 Note You can use the other USB side port for a peripheral device such as a wireless modem tracking device keyboard or mouse Bantam Installation Guide Chapter 4 Operating Bantam Powering the System Inserting and Removing the USB Flash Drive Understanding the 7 Screen Control Panel Adjusting the Display Brightness Adjusting the Lightbar Brightness Calibrating the Touchscreen Turning the System Off 21 PN 875 0265 000 Rev B1 Chapter 4 Operating Bantam use the USB adjust the display and lightbar brightness and calibrate your N ow that the system is installed and connected you are ready to turn it on and touchscreen Powering the System The ON OFF lever switch on the power panel see About the Power Cable
9. can damage your system Pile Consider using existing hardware and hardware locations Avoid drilling holes that may damage other equipment such as structural frame members electrical cables or fluid lines Where hardware such as screws washer and nuts is not provided for a particular mounting or installation you will need to provide the hardware appropriate to your particular needs CPU The CPU is a semi permanent fixture once installed there is no quick release mechanism Install the CPU in any location inside the vehicle that has the necessary room and is sheltered from the elements for example in a storage compartment in the cab behind the seat The CPU must have sufficient clearance to be accessible for attaching removing cables front and both sides and for inserting and removing the USB flash drive however see Inserting and Removing the USB Flash Drive on page 22 Obtain the necessary hardware to secure the CPU through its fitting points at each corner and install it in your selected location PIVEN Stem Do not mount the CPU vertically The CPU must be mounted on a horizontal surface Touchscreen Mount the touchscreen inside the cockpit or cab of the vehicle where it is e Easily visible while flying or driving e Within arm s reach PIVEN lem Do not obstruct the view or access to other instruments or the flying or driving visibility of the pilot or driver Bantam Installation Guide 6 PN 875 0265 000
10. 10 32 x M 5 8 bolt nut and washer sets Substitute a 3 bracket for one of the 1 brackets if added height n Um a END VIEW is needed 2 5 29 45 T 1 m This or 1 a either of these p Bantam Installation Guide 12 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components 3 Attach the left and right brackets to the lightbar plates using the four 4110 32 x 1 2 screw nut and washer sets 4 Using the assembled lightbar and brackets as a template mark the four mounting hole locations on the surface of the vehicle 5 Using a 1 4 drill bit carefully drill the four holes 6 Using 10 32 bolts washers and nuts secure the lightbar to the vehicle Use the 194 or 34 bolts depending on if you are mounting the lightbar on a thick or a thin mounting surface 7 W reguired attach the backing k 14 plates to the underside of the mounting surface for additional reinforcement The backing E plates provide additional support to prevent the bolts from pulling through the surface under vibration BEBA 8888 STRUCTURE E Bantam Installation Guide 13 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components Antenna Mounting Location Antenna position is critical to system performance These conditions must be met for proper system operation Mount the antenna at least 5 ft 1 524 m from transmitting antennas of any frequency iV EAS litem Positioning the antenna
11. NY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS SHALL BE AVAILABLE TO PURCHASER even if Hemisphere GPS has been advised of the possibility of such damages Without limiting the foregoing Hemisphere GPS shall not be liable for any damages of any kind resulting from installation use quality performance or accuracy of any Product HEMISPHERE IS NOT RESPONSIBLE FOR PURCHASER S NEGLIGENCE OR UNAUTHORIZED USES OF THE PRODUCT IN NO EVENT SHALL HEMISPHERE GPS BE IN ANY WAY RESPONSIBLE FOR ANY DAMAGES RESULTING FROM PURCHASER S OWN NEGLIGENCE OR FROM OPERATION OF THE PRODUCT IN ANY WAY OTHER THAN AS SPECIFIED IN HEMISPHERE GPS S RELEVANT USER S MANUAL AND SPECIFICATIONS Hemisphere GPS is NOT RESPONSIBLE for defects or performance problems resulting from 1 misuse abuse improper installation neglect of Product 2 the utilization of the Product with hardware or software products information data systems interfaces or devices not made supplied or specified by Hemisphere GPS 3 the operation of the Product under any specification other than or in addition to the specifications set forth in Hemisphere GPS s relevant User s Manual and Specifications 4 damage caused by accident or natural events such as lightning or other electrical discharge or fresh salt water immersion of Product 5 damage occurring in transit 6 normal wear and tear or 7 the operation or failure of operation of any satellite based positioning system or differential correctio
12. Rev B1 Chapter 2 Mounting the Components The 7 Touchscreen Mounting Kit Note You will need to be able to get behind the dashboard to secure the dash mounting plate The 7 touchscreen comes with a template mounting plates and mounting hardware as follows Table 2 1 7 touchscreen mounting kit 1 Touchscreen mounting plate Mounts on the 601 1203 000 1 touchscreen for mounting on the dashboard plate item 5 Screws flat head M2 5 x 8 mm secure plate 675 1207 000 to back of touchscreen Screws flat head M2 5 x 5 mm secure plate 675 1137 000 to base of touchscreen Template for the dashboard mounting plate N A Cut out and stick on the dashboard drill as indicated 2 3 5 Screw washer and nut Attach dashboard 675 1208 000 screw plate to dash 678 10990000000 washer 676 1066 000 nut 7 Threaded knobs also known as flowerette 679 1011 O00 thumb screws Attach touchscreen and plate assembly to dashboard plate a zi Dashboard threaded mounting plate 601 120000 1 Mounts on dashboard Touchscreen mounting plate attaches to this plate Bantam Installation Guide 7 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components Mounting the 7 Touchscreen 1 Attach the touchscreen mounting plate to the touchscreen Use the four 8 mm length screws into the back of the touchscreen the two 5 mm screws into the bottom of the touchscreen 2 Cutoutthe suppli
13. assembly p n 726 1096 000 Power panel V Lightbar cable Video cable GPIO cable p n 051 0022 001 p n 051 0243 000 p n 051 0244 000 to lightbar to touchscreen to spray on off switch swath advance switch serial connector DB9 n Connecting Cables You install each Bantam cable between the CPU and a modular component for example the antenna cable or the touchscreen or a peripheral device such as AgLaser Each cable is labeled with its name and part number and the connections are color coded Each cable can fit only one port on the CPU it is impossible to connect a cable to the wrong port Line up a connector with its matching pins and gently insert and turn AWARNING Never force connections Finger tighten only do not use tools Bantam Installation Guide 17 PN 875 0265 000 Rev B1 Chapter 3 Connecting the CPU Connecting the GPIO Cable The GPIO cable part number 051 0244 000 comprises several individual cables for the spray on off switch the swath advance switch a serial port DB9 connector To connect the GPIO cable 1 Connect the Conxall connector end of the cable part number 051 0244 000 to the CPU serial port labeled GPIO 2 Connect the spray on off switch cable leads to the provided momentary lever switch part number 075 4001 000 Use the switch in conjunction with your spray system on off controls to synchronize actual spraying with the spray data collecti
14. e more copies of the Software than the number of copies that have been licensed b use or install the Software in connection with any product other than the Product the Software was intended to be used or installed on as set out in the documentation that accompanies the Software C copy any of the Software or any written materials for any purpose except as part of Licensee s normal backup processes modify or create derivative works based on the Software d e sub license rent lease loan or distribute the Software f permit any third party to use the Software g use or operate Product for the benefit of any third party in any type of service outsourcing application service provider service or service bureau capacity h reverse engineer decompile or disassemble the Software or otherwise reduce it to a human perceivable form i Assign this Agreement or sell or otherwise transfer the Software to any other party except as part of the sale or transfer of the whole Product 3 UPDATES At Hemisphere s discretion Hemisphere may make Updates available to Licensee An update Update means any update to the Software that is made available to Licensee including error corrections enhancements and other modifications Licensee may access download and install Updates during the Warranty Period only All Updates that Licensee downloads installs or uses shall be deemed to be Software and subject to this Agreement Hemisphere reserves the ri
15. e shall indemnify and hold Hemisphere harmless from any and all claims damages losses liabilities costs and expenses including reasonable fees of lawyers and other professionals arising out of or in connection with Licensee s use of the Product whether direct or indirect including without limiting the foregoing loss of data loss of profit or business interruption 21 22 23 24 25 26 27 28 TERMINATION Licensee may terminate this Agreement at any time without cause Hemisphere may terminate this Agreement on 30 days notice to Licensee if Licensee fails to materially comply with each provision of this Agreement unless such default is cured within the 30 days Any such termination by a party shall be in addition to and without prejudice to such rights and remedies as may be available including injunction and other equitable remedies Upon receipt by Licensee of written notice of termination from Hemisphere or termination by Licensee Licensee shall at the end of any notice period a cease using the Software and b return to Hemisphere or destroy and provide a certificate of a Senior Officer attesting to such destruction the Software and all related material and any magnetic or optical media provided to Licensee The provisions of Sections 6 7 8 9 10 15 21 26 and 27 herein shall survive the expiration or termination of this Agreement for any reason EXPORT RESTRICTIONS Licensee agrees that Licensee w
16. ed template and place it on a clear area of the dashboard i Note You must be able to get i behind the dashboard to attach nan washers and nuts 3 Drill the dashboard using the template then using the four screws washers and nuts attach the dashboard mounting plate to the dashboard 4 Using the two thumb screws attach the touchscreen and its plate to the dashboard plate Bantam Installation Guide 8 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components The 8 4 Touchscreen Mounting Kit The 8 4 touchscreen comes with a ball mount assembly as follows Table 2 2 8 4 touchscreen mounting kit RAM mount RAM mount assembly 101U 101U 603 1004 000 cm Nut 8 32 hex a locking SS 676 1018 000 Washer flat 8 678 1010 000 Mounting the 8 4 Touchscreen 1 Identify the best available location for the ball and arm mount 2 Using your own hardware attach one ball mount to a suitable structure surface on the vehicle 3 Using the provided nuts and washers mount the other ball on the studs on the back of the touchscreen 4 With the arm installed between the two ball mounts set the touchscreen in a suitable position then tighten the handle When loosening the handle the socket on the sprung side of the arm opens first Bantam Installation Guide 9 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components Power Panel Power Panel Mounting Locati
17. eeding Licensee shall not settle or compromise any of same for which Hemisphere has agreed to assume responsibility without Hemisphere s prior written consent Licensee may at its sole cost and expense retain separate counsel from the counsel utilized or retained by Hemisphere INFRINGEMENT If use of the Software may be enjoined due to a claim of infringement by a third party then at its sole discretion and expense Hemisphere may do one of the following a negotiate a license or other agreement so that the Product is no longer subject to such a potential claim b modify the Product so that it becomes non infringing provided such modification can be accomplished without materially affecting the performance and functionality of the Product c replace the Software or the Product with non infringing software or product of equal or better performance and quality or d if none of the foregoing can be done on a commercially reasonable basis terminate this license and Licensee shall stop using the Product and Hemisphere shall refund the price paid by Licensee less an amount on account of amortization calculated on a straight line basis over a deemed useful life of three 3 years The foregoing sets out the entire liability of Hemisphere and the sole obligations of Hemisphere to Licensee in respect of any claim that the Software or its use infringes any third party rights INDEMNIFICATION Except in relation to an infringement action License
18. ensee subject to the exclusions and procedures set forth herein below that for a period of one 1 year from the original date of purchase of the Product in which it is embedded the Warranty Period the Software under normal use and maintenance will conform in all material respects to the documentation provided with the Software and any media will be free of defects in materials and workmanship For any Update Hemisphere warrants for 90 days from performance or delivery or for the balance of the original Warranty Period whichever is greater that the Update under normal use and maintenance will conform in all material respects to the documentation provided with the Update and any media will be free of defects in materials and workmanship Notwithstanding the foregoing Hemisphere does not warrant that the Software will meet Licensee s requirements or that its operation will be error free 9 WARRANTY EXCLUSIONS The warranty set forth in Section 8 will not apply to any deficiencies caused by a the Product not being used as described in the documentation supplied to Licensee b the Software having been altered modified or converted in any way by anyone other than Hemisphere approved by Hemisphere c any malfunction of Licensee s equipment or other software or d damage occurring in transit or due to any accident abuse misuse improper installation lightning or other electrical discharge or neglect other than that caused by Hemisphe
19. ent location in your cockpit or cab You can then connect the USB flash drive to the extension cable using the supplied connector Bantam Installation Guide 22 PN 875 0265 000 Rev B1 Chapter 4 Operating Bantam Note To use the USB flash drive you must insert it into the CPU using the remote connector as required before turning the system on If you start the system before inserting the USB turn off the Bantam insert the USB and restart the system Always turn off the Bantam before removing the USB Understanding the 7 Screen Control Panel This section provides a brief description of the functions of the buttons and lights on the control panel area of the 7 touchscreen What the buttons do sometimes depends on whether the M Menu button has already been pressed that is if an on screen menu is open Table 4 1covers both situations Table 4 1 The 7 touchscreen control panel Panel Item Description and Usage D Display Display brightness Press to cycle through brightness levels Bright Mid or Dark See also Adjusting the Display Brightness on page 24 Menu closed Increase decrease volume not used Menu open Increase decrease value of selected menu row or switch between two values S Source or Menu closed Source cycle through input sources AV1 AV2 PC Select Menu open Select move through the menu options rows M Menu Call up on screen menus press twice to access second level menu Use S to
20. ess implied or arising by statute by course of dealing or by trade usage in connection with the design sale installation service or use of any products or any component thereof are EXCLUDED from this transaction and shall not apply to the Product The LIMITED WARRANTY is IN LIEU OF any other warranty express or implied including but not limited to any warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE title and non infringement LIMITATION OF REMEDIES The purchaser s EXCLUSIVE REMEDY against Hemisphere GPS shall be at Hemisphere GPS s option the repair or replacement of any defective Product or components thereof The purchaser shall notify Hemisphere GPS or a Hemisphere GPS s approved service center immediately of any defect Repairs shall be made through a Hemisphere GPS approved service center only Repair modification or service of Hemisphere GPS products by any party other than a Hemisphere GPS approved service center shall render this warranty null and void The remedy in this paragraph shall only be applied in the event that the Product is properly and correctly installed configured interfaced maintained stored and operated in accordance with Hemisphere GPS s relevant User s Manual and Specifications AND the Product is not modified or misused NO OTHER REMEDY INCLUDING BUT NOT LIMITED TO SPECIAL INDIRECT INCIDENTAL CONSEQUENTIAL OR CONTINGENT DAMAGES FOR LOST PROFITS LOST SALES INJURY TO PERSON OR PROPERTY OR A
21. ght to modify the Product without any obligation to notify supply or install any improvements or alterations to existing Software 4 SUPPORT Hemisphere may make available directly or through its authorized dealers telephone and email support for the Software Contact Hemisphere to find the authorized dealer near you As well Hemisphere may make available user and technical documentation regarding the Software Hemisphere reserves the right to reduce and limit access to such support at any time 5 BACKUPS AND RECOVERY Licensee shall back up all data used created or stored by the Software on a regular basis as necessary to enable proper recovery of the data and related systems and processes in the event of a malfunction in the Software or any loss or corruption of data caused by the Software Licensee shall assume all risks of loss or damage for any failure to comply with the foregoing 6 OWNERSHIP Hemisphere and its suppliers own all rights title and interest in and to the Software and related materials including all intellectual property rights The Software is licensed to Licensee not sold 7 TRADEMARKS Hemisphere GPS Outback Guidance BEELINE Crescent Eclipse and the associated logos are trademarks of Hemisphere Other trademarks are the property of their respective owners Licensee may not use any of these trademarks without the consent of their respective owners 8 LIMITED WARRANTY Hemisphere warrants solely to the Lic
22. he Power Cable The power cable assembly part number 726 1096 000 comprises the following o Power panel on which there is an ON OFF switch e Dimmer switch to control the lightbar s brightness e Circuit breaker that prevents voltage spikes and reverse polarity from damaging the system Note The ON OFF switch powers the CPU and the touchscreens It powers the 7 touchscreen directly the 8 4 touchscreen indirectly see Powering the System on page 22 The dimmer switch on the power panel controls lightbar brightness both touchscreens have their own display brightness controls Connecting the Power Cable AWARNING e Do not connect to a power source of less than 10 volts e Do not use a cigarette lighter as a permanent power source e Do not reverse the polarity of the power leads incorrect installation can damage the system Connect RED to POSITIVE and BLACK to NEGATIVE Connect the Conxall connector to the CPU port labeled POWER 2 Connect the red and black power leads to a suitable power source that can supply between 10 and 36 V for example vehicle battery generator Air Installation A potential problem when installing an electronic system in a vehicle is Counter Electromagnetic Force CEMF CEMF is caused when relays or solenoids connected to the common vehicle DC power bus are de energized The voltage produced may exceed 400 V CEMF can be produced by equipment such as o Electric fan
23. i Rc afer dott 25 lil dep UE raves oa a gee VA ek ee ay aca ar Mie mca ate Boe ake HATE nave ace 27 End User License Agreement 29 Warranty N tIC zeir erdan iG ieee eee eee See ees 32 Bantam Installation Guide iv PN 875 0265 000 Rev B1 Chapter 1 Getting Started Parts List Component Weights Planning the Installation Bantam Installation Guide 1 PN 875 0265 000 Rev B1 Chapter 1 Getting Started he Bantam is a modular system that features a powerful CPU in a rugged aluminum box The CPU contains a serial port for each module Each module of the system connects to the CPU via a specific cable The system modules that ship with the Bantam and connect to the CPU are 7 or 8 4 color touchscreen e Lightbar e Antenna o Optional switches spray on off swath advance P ii leM Read this entire manual before beginning installation Failure to follow the instructions in this manual could void your warranty Pay careful attention to safety reminders and warnings to eliminate the possibility of personal injury or damage to the system Comply with all electrical connections and reguirements to prevent damage to the system Parts List Review the contents of your Bantam purchase to ensure the components are not damaged The contents will vary depending on whether you ordered a 7 or 8 4 screen Table 1 1 Bantam main parts list Baiam swiches andi Se Ter SETS Baran cables seers ERR
24. ill comply with all export control legislation of Canada the United States Australia and any other applicable country s laws and regulations whether under the Arms Export Control Act the International Traffic in Arms Regulations the Export Administration Regulations the regulations of the United States Departments of Commerce State and Treasury or otherwise as well as the export control legislation of all other countries PRODUCT COMPONENTS The Product may contain third party components Those third party components may be subject to additional terms and conditions Licensee is required to agree to those terms and conditions in order to use the Product FORCE MAJEURE EVENT Neither party will have the right to claim damages as a result of the other s inability to perform or any delay in performance due to unforeseeable circumstances beyond its reasonable control such as labor disputes strikes lockouts war riot insurrection epidemic Internet virus attack Internet failure supplier failure act of God or governmental action not the fault of the non performing party FORUM FOR DISPUTES The parties agree that the courts located in Calgary Alberta Canada and the courts of appeal there from will have exclusive jurisdiction to resolve any disputes between Licensee and Hemisphere concerning this Agreement or Licensee s use or inability to use the Software and the parties hereby irrevocably agree to attorn to the jurisdiction of those courts
25. itch Outback STM Outback S2 Outback S3 M Outback S Lite Outback Sts Outback Steering Guide PocketMAX PC PocketMAXTM PocketMax3 R100 R131 R220 R320 Satloc the Satloc logo SBX 4 V101 V102 V111 M VS101 VS111 Vector X200 X300 XF100 XF101 and XF102 are proprietary trademarks of Hemisphere GPS Other trademarks are the properties of their respective owners Patents The Outback S and S Lite automated navigation and steering guide systems are covered by U S Patents No 6 539 303 and No 6 711 501 The Outback Hitch automated hitch control system is covered by U S Patent No 6 631 916 The Outback eDriveTC GPS assisted steering system is covered by U S Patent No 7 142 956 Hemisphere GPS products may be covered by one or more of the following U S Patents 6 111 549 6 397 147 6 469 663 6 501 346 6 539 303 6 549 091 6 631 916 6 711 501 6 744 404 6 865 465 6 876 920 7 142 956 7 162 348 7 277 792 7 292 185 7 292 186 7 373 231 7 400 956 7 400 294 7 388 539 7 429 952 7 437 230 7 460 942 Other U S and foreign patents pending Notice to Customers Contact your local dealer for technical assistance To find the authorized dealer near you Hemisphere GPS 2207 lowa Street Hiawatha KS 66434 Phone 785 742 2976 Fax 785 742 4584 ground hemispheregps com www hemispheregps com Technical Support If you need to contact Hemisphere GPS Technical
26. less than 5 ft 1 524 m from transmitting antennas of any frequency may cause overloading of RF circuits Mount the antenna at the highest practical point that will give a good view of the horizon The positions that the receiver calculates are at the positions of the antenna So if using a swath guidance system mount the antenna on the center line of the vehicle Mounting the Antenna Hemisphere GPS recommends flush mounting the antenna to the roof of the vehicle Tools needed Phillips screwdriver Four 48 32 screws Electric drill 1 8 drill bit 7 16 drill bit Marker pen Follow this procedure to mount the antenna T Use the A21 antenna mounting template to mark the mounting and antenna connector hole locations on the outer surface of the vehicle Using a 1 8 drill bit carefully drill the four screw holes Using a 7 16 drill bit carefully drill the hole for the antenna connector Use four 8 32 thread screws to secure the antenna to the surface of the vehicle Bantam Installation Guide 14 PN 875 0265 000 Rev B1 Chapter 3 Connecting the CPU Warnings Connections Diagram Connecting Cables Bantam Installation Guide 15 PN 875 0265 000 Rev B1 Chapter 3 Connecting the CPU Warnings Heed all warnings before continuing Failure to do so could void your warranty General Cable Connection Warnings AWARNING Turn off power before connecting or disconnecting cables Failing to do so can damage the
27. lt two x item 3s together or an item 3 678 1038 000 washer and an item 4 together 676 1016 000 nut 1110 32 x 1 2 bolt washer and nut set 675 1086 000 bolt bolt item 1 plates to item 3 or 4 678 1038 000 washer brackets 676 1016 000 nut 3410 32 x 134 and 34 optional bolt 675 1085 000 134 bolt washer and nut set bolt item 3 or 4 675 1084 000 34 bolt bracket to vehicle use item 5 backing 678 1038 000 washer plates if necessary 676 1016 000 nut Mounting the Lightbar Tools Needed e Phillips screwdriver 3 16 Allen wrench 3 8 wrench e Electric drill 1 4 drill bit o Marker pen Bantam Installation Guide 11 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components Follow this procedure to mount the lightbar 1 Secure the left and right flat panel plates to the lightbar using the two 48 32 screws Note The screw holes are offset to the outside edge of the plate Also the front of the lightbar faces the thin edge of the plate and the rear of the lightbar rests on the thick edge of the plate Front Rear Front of lightbar towards the thin edge of the sloped plates Plch If you have the left and right plates reversed it is still possible to line up the plates so the arrows are pointing outside However the screw holes on the lightbar and the flat panel plate will not line up if you have them reversed 2 Assemble the two sets of 1 35 1 brackets using the 4
28. n service or the availability or performance of any satellite based positioning signal or differential correction signal THE PURCHASER IS RESPONSIBLE FOR OPERATING THE VEHICLE SAFELY The purchaser is solely responsible for the safe operation of the vehicle used in connection with the Product and for maintaining proper system control settings UNSAFE DRIVING OR SYSTEM CONTROL SETTINGS CAN RESULT IN PROPERTY DAMAGE INJURY OR DEATH The purchaser is solely responsible for his her safety and for the safety of others The purchaser is solely responsible for maintaining control of the automated steering system at all times THE PURCHASER IS SOLELY RESPONSIBLE FOR ENSURING THE PRODUCT IS PROPERLY AND CORRECTLY INSTALLED CONFIGURED INTERFACED MAINTAINED STORED AND OPERATED IN ACCORDANCE WITH HEMISPHERE GPS S RELEVANT USER S MANUAL AND SPECIFICATIONS Hemisphere GPS does not warrant or guarantee the positioning and navigation precision or accuracy obtained when using Products Products are not intended for primary navigation or for use in safety of life applications The potential accuracy of Products as stated in Hemisphere GPS literature and or Product specifications serves to provide only an estimate of achievable accuracy based on performance specifications provided by the satellite service operator i e US Department of Defense in the case of GPS and differential correction service provider Hemisphere GPS reserves the right to modify Products without
29. ny implied warranties or conditions which would then otherwise arise will be limited in duration to ninety 90 days from the date of the license of the Software or the purchase of the Product The warranties given herein give Licensee specific legal rights and Licensee may have other rights which may vary from jurisdiction to jurisdiction CHANGE TO WARRANTY No employee or agent of Hemisphere is authorized to change the warranty provided or the limitation or disclaimer of warranty provisions All such changes will only be effective if pursuant to a separate agreement signed by senior officers of the respective parties WARRANTY CLAIM In the event Licensee has a warranty claim Licensee must first check for and install all Updates that are made available The warranty will not otherwise be honored Proof of purchase may be required Hemisphere does not honor claims asserted after the end of the Warranty Period LICENSEE REMEDIES In all cases which involve a failure of the Software to conform in any material respect to the documentation during the Warranty Period or a breach of a warranty Hemisphere s sole obligation and liability and Licensee s sole and exclusive remedy is for Hemisphere at Hemisphere s option to a repair the Software b replace the Software with software conforming to the documentation or c if Hemisphere is unable on a reasonable commercial basis to repair the Software or to replace the Software with conforming software wi
30. ompanies this Agreement This Software may be licensed on a standalone basis or may be embedded in a Product Please read and ensure that you understand this Agreement before installing or using the Software Update or using a Product In this agreement any product that has Software embedded in it at the time of sale to the Licensee shall be referred to as a Product As well in this Agreement the use of a Product shall be deemed to be use of the Software which is embedded in the Product BY INSTALLING OR USING THE SOFTWARE UPDATE OR THE PRODUCT LICENSEE THEREBY AGREES TO BE LEGALLY BOUND BY THE TERMS OF THIS AGREEMENT IF YOU DO NOT AGREE TO THESE TERMS I DO NOT INSTALL OR USE THE SOFTWARE AND II IF YOU ARE INSTALLING AN UPDATE TO THE SOFTWARE DO NOT INSTALL THE UPDATE AND PROMPTLY DESTROY IT HEMISPHERE PROVIDES LIMITED WARRANTIES IN RELATION TO THE SOFTWARE AS WELL THOSE WHO USE THE EMBEDDED SOFTWARE DO SO AT THEIR OWN RISK YOU SHOULD UNDERSTAND THE IMPORTANCE OF THESE AND OTHER LIMITATIONS SET OUT IN THIS AGREEMENT BEFORE INSTALLING OR USING THE SOFTWARE OR THE PRODUCT 1 LICENSE Hemisphere hereby grants to Licensee a non transferable and non exclusive license to use the Software as embedded in a Product and all Updates collectively the Software solely in binary executable form 2 RESTRICTIONS ON USE Licensee agrees that Licensee and its employees will not directly or indirectly in any manner whatsoever a install or us
31. on Mount the power panel part of cable harness part number 726 1096 000 inside the cockpit or cab of the vehicle The power panel must be within arm s reach AWARNING Do not obstruct the view or access to other instruments or the flying or driving visibility of the pilot or driver Mounting the Power Panel 1 Find an appropriate location in your cockpit or cab to mount the power panel It must be within easy reach of the pilot or driver 2 Depending on the selected location and vehicle type use the appropriate hardware not supplied to attach the power panel to the vehicle Bantam Installation Guide 10 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components Lightbar The lightbar installation is the same for aircraft and ground vehicles Lightbar Mounting Location Mount the lightbar in front of the cockpit or cab at a comfortable viewing distance You can mount the lightbar either inside or outside of the cockpit or cab PIVEN tem Do not block the view of the pilot or driver The Lightbar Mounting Kit The lightbar mounting kit part number 710 0029 002 contains these items Table 2 3 IM mounting kit S panel plate 603 1005 000 right side 603 1006 000 left side Screw 8 32 attach item 1 plate to 675 1100 000 Chae Braket 1 1 602 1007000 1007 000 LEN plate use with item 8 if 601 1045 000 required 1110 32 x 5 8 bolt nut and washer set 675 1083 000 bolt bo
32. on functionality of Bantam See also Using the Flow Control Port on page 18 PVGH Do not connect spray on off leads to a flow system if it contains live voltage Connection to a DC voltage will damage the circuit 3 Optional Connect the swath advance cable leads to push switch part number 075 4002 000 to control swath advances remotely Connecting the Lightbar Cable 1 Connect the Conxall connector of the lightbar cable part number 051 0022 001 to the CPU port labeled LIGHTBAR 2 Connect the metal Bendix connector on the lightbar cable to the matching connector on the back of the lightbar Connecting the Antenna Cable Connect the antenna cable part number 052 0005 000 between the socket on the left side of the CPU and the A21 antenna Connecting a Keyboard and or Mouse You can connect a keyboard and a mouse that have USB connectors directly or indirectly through an extension cable to the USB ports on either side of the CPU Using the Flow Control Port Connect the cable that comes with your flow control system IntelliFlow or IntelliGate to the flow control port Connecting the Video VGA Cable 1 Connect the Conxall connector on cable part number 051 0243 000 to the CPU serial port labeled DISPLAY 2 Connect the other end of the cable to the red coded connector on the back of the touchscreen Bantam Installation Guide 18 PN 875 0265 000 Rev B1 Chapter 3 Connecting the CPU About t
33. ouchscreen mounting 9 powering 22 A antenna mounting 14 mounting location 14 antenna cable connecting 18 arrows up and down 7 screen 23 B brightness adjusting 24 buttons arrows updown 7 screen 23 brightness 8 4 screen 24 control panel 7 screen 23 D button 7 screen 23 M enu button 7 screen 23 S button 7 screen 23 C cables connecting 17 connections diagram 17 parts list 3 calibrating touchscreens 24 components weight of 4 connections antenna cable 18 cables 17 cables diagram 17 GPIO cable 18 lightbar cable 18 mouse and keyboard 18 power cable 19 to flow control port 18 USB and extension cable 20 video VGA cable 18 control panel understanding 23 CPU Bantam Installation Guide 27 installation 6 installing clearance 6 introduction to 6 mounting vertically 6 powering 22 D D button 7 screen 23 display see touchscreen eight see 8 4 touchscreen F flash drive see USB flow control IntelliFlow 18 IntelliGate 18 port using 18 G GPIO cable connecting 18 green light 7 screen 23 installation see also mounting antenna 14 CPU 6 CPU clearance 6 lightbar 11 planning 4 power panel 10 touchscreens 6 IntelliFlow using the flow control port 18 IntelliGate using the flow control port 18 K keyboard connecting 18 kits and switches parts list 3 L lightbar brightness adjusting 24 cable connecting 18 mounting 11 mounting kit 11
34. ptional spray on off switch optional 051 0244 000 swath advance switch serial DB9 connector Antenna cable 052 0005 000 Power cable assembly 726 1096 000 Includes mountable panel with power switch for the CPU circuit breaker and dimmer switch to control the lightbar brightness Bantam Installation Guide 3 PN 875 0265 000 Rev B1 Chapter 1 Getting Started Component Weights Table 1 4 Component weights mem m Touchscreen 8 4 4 46 pounds 2 02 kg Lightbar V1 4 2 pounds 1 91 kg Complete cable set 7 0 pounds 3 18 kg Antenna 0 75 pounds 0 34 kg Planning the Installation Pile Before beginning the installation plan it by considering Cable lengths Clearance space e Power source e Vehicle structure e Visibility e Balance air installations In planning your installation locations see Chapter 3 Connecting the CPU for a visual overview of how the components are connected Bantam Installation Guide 4 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components CPU Touchscreen Power Panel Lightbar Antenna Bantam Installation Guide 5 PN 875 0265 000 Rev B1 Chapter 2 Mounting the Components efore installing any components read the short section Planning the Installation on page 4 Plc Review all warnings in Chapter 3 Connecting the CPU before attempting to connect any of the components together using the supplied cables Connecting cables improperly
35. r touchscreen 1 Power on your Bantam AirTrac system 2 Onthe Disclaimer screen press ACCEPT 3 OntheSelect Additional Options Confirm Logging Device screen press Exit to Windows The Welcome splash screen appears briefly On the Windows desktop double tap Touchkit Select the Tools tab Select 4 Points Calibration NOOR Touch and hold the center of the cross hairs until OK appears and then repeat for the other three points On the Completed message press OK 9 Close the Touchkit window 10 Shut down Windows and power off the system see the next section Turning the System Off Bantam Installation Guide 24 PN 875 0265 000 Rev B1 Chapter 4 Operating Bantam Turning the System Off Before turning off the touchscreen or the main power source it is important to shut down Windows by following this procedure Press the Start button in the lower left hand corner of the Windows screen Press Shut Down Highlight the Shut Down choice then press OK Wait until you see the message It s now safe to turn off your computer of WN Shut down power to the touchscreen by pressing the Power button 8 4 touchscreen only For the 7 touchscreen go to step 6 6 Turn off system power Bantam Installation Guide 25 PN 875 0265 000 Rev B1 Index Numerics 7 touchscreen control panel understanding 23 D button 23 M button 23 mounting 8 powering 22 S button 23 up and down arrows 23 8 4 t
36. re Hemisphere GPS does not warrant or guarantee the precision or accuracy of positions obtained when using the Software whether standalone or embedded in a Product The Product and the Software is not intended and should not be used as the primary means of navigation or for use in safety of life applications The potential 10 11 12 13 14 15 16 17 18 19 20 positioning and navigation accuracy obtainable with the Software as stated in the Product or Software documentation serves to provide only an estimate of achievable accuracy based on specifications provided by the US Department of Defense for GPS positioning and DGPS service provider performance specifications where applicable WARRANTY DISCLAIMER EXCEPT AS EXPRESSLY SET OUT IN THIS AGREEMENT HEMISPHERE MAKES NO REPRESENTATION WARRANTY OR CONDITION OF ANY KIND TO LICENSEE WHETHER VERBAL OR WRITTEN AND HEREBY DISCLAIMS ALL REPRESENTATIONS WARRANTIES AND CONDITIONS OF ANY KIND INCLUDING FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY ACCURACY RELIABILITY OR THAT THE USE OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR FREE AND HEREBY DISCLAIMS ALL REPRESENTATIONS WARRANTIES AND CONDITIONS ARISING AS A RESULT OF CUSTOM USAGE OR TRADE AND THOSE ARISING UNDER STATUTE LIMITS ON WARRANTY DISCLAIMER Some jurisdictions do not allow the exclusion of implied warranties or conditions so some of the above exclusions may not apply to Licensee In that case a
37. select row use arrows to change values Power on off button While ON OFF lever switch on the power panel is ON turns screen off and back on See also Turning the System 9 on off Off on page 25 When on screen is powered power button and power lever ON OFF switch both on power Not used Bantam Installation Guide 23 PN 875 0265 000 Rev B1 Chapter 4 Operating Bantam Adjusting the Display Brightness You adjust the display brightness differently for the 8 4 and 7 touchscreens 8 4 screen 7 screen To adjust the display brightness of the 8 4 touchscreen press the brightness up and down arrow buttons To adjust the display brightness of the 7 touchscreen press the D Display button on the control panel below the screen to cycle the display brightness through Bright Mid Dark You can also adjust the 7 screen brightness if you have the first menu open by using S to select the Brightness row if necessary and using the panel s up and down arrows to change the display brightness to another of the three levels Adjusting the Lightbar Brightness Adjust the lightbar brightness for night operation by turning the lightbar DIMMER control knob on the power panel Calibrating the Touchscreen Both the 7 and 8 4 touchscreens are shipped properly calibrated Touchscreen calibration ensures that the cursor is placed exactly under your finger when you touch the screen If you need to recalibrate you
38. ser the Products unless otherwise specifically and expressly agreed in writing by Hemisphere GPS LIMITED WARRANTY Hemisphere GPS warrants solely to the end purchaser of the Products subject to the exclusions and procedures set forth below that the Products sold to such end purchaser and its internal components shall be free under normal use and maintenance from defects in materials and workmanship and will substantially conform to Hemisphere GPS s applicable specifications for the Product for a period of 12 months from delivery of such Product to such end purchaser the Warranty Period Repairs and replacement components for the Products are warranted subject to the exclusions and procedures set forth below to be free under normal use and maintenance from defects in material and workmanship and will substantially conform to Hemisphere GPS s applicable specifications for the Product for 90 days from performance or delivery or for the balance of the original Warranty Period whichever is greater EXCLUSION OF ALL OTHER WARRANTIES The LIMITED WARRANTY shall apply only if the Product is properly and correctly installed configured interfaced maintained stored and operated in accordance with Hemisphere GPS s relevant User s Manual and Specifications AND the Product is not modified or misused The Product is provided AS IS and the implied warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE and ALL OTHER WARRANTIES expr
39. system Finger tighten all cable connections Do not use any tools Do not route cables alongside power generator wire and other high noise electric sources This will cause interference Do not kink or force cables into sharp bands This can damage the cable Store excess cable length with at least a 6 in bend radius Do not coil the cables This will introduce noise in the system Avoid high temperature exposure for example exhaust manifold when routing cables Antenna Cable Warning AWARNING Never connect or disconnect the antenna cable with the power on Do not route the antenna cable with any other radio system cables This will cause interference Keep 12 inches apart If you must cross the antenna cable with other cables do so at a 90 angle This will prevent interference between systems Bantam Installation Guide 16 PN 875 0265 000 Rev B1 Chapter 3 Connecting the CPU Connections Diagram The following diagram provides a visual representation of the connections of the Bantam system Refer to this diagram when planning your installation and again when you are ready to connect the components USB extension cable part of kit p n 710 0087 000 USB flash drive connector extension cable 7 L to either port rer n l 4 G Antenna cable p n 052 0005 000 A dn to antenna Flow control port for m Z your flow control system s cable Power cable
40. tante dtu nae stare ate 14 MOUNTING LOCATION 5 3 tea neca bk RR Che Sle RR ocio 14 Mounting the Antenna een 14 Connecting the CPU 15 MAE S vo hk soccer acne eet ae arty am ated O E fa cee are 16 General Cable Connection Warnings 16 Antenna Cable Warning seen 16 Connections Diagratn 35 252 s ouv kel Poets betes E A 17 Connecting Cables 4 3 2 aad Rh oos edi Po ER So eoa 17 Connecting the GPIO Cable 18 Connecting the Lightbar Cable llus 18 Connecting the Antenna Cable llus 18 Connecting a Keyboard and or Mouse 18 Using the Flow Control Port 18 Connecting the Video VGA Cable 18 About the Power Cable llle 19 Connecting the Power Cable 19 Connecting the USB Extension Cable 20 Operating Bantam 21 Bantam Installation Guide Hl PN 875 0265 000 Rev B1 Contents Powering the System x s v vadis da 3806 Rx env T MUR o dada 22 Turning the CPU and Screens On 22 Inserting and Removing the USB Flash Drive 22 Understanding the 7 Screen Control Panel 23 Adjusting the Display Brightness 0 0000 e eee eee 24 Adjusting the Lightbar Brightness less 24 Calibrating the Touchscreen 00 0 c eee eee eee eee 24 Turning the System OTT z sea ied ate Gotta son t x ae oc
41. the parties have entered into this Agreement in reliance on the limited warranties warranty disclaimers and limitations of liability set forth herein that the same reflect an agreed to allocation of risk between the parties including the risk that a remedy may fail of its essential purpose and cause consequential loss and that the same forms an essential basis of the bargain between the parties Licensee agrees and acknowledges that Hemisphere would not have been able to sell the Product at the amount charged on an economic basis without such limitations PROPRIETARY RIGHTS INDEMNITY Hemisphere shall indemnify defend and hold harmless Licensee from and against any and all actions claims demands proceedings liabilities direct damages judgments settlements fines penalties costs and expenses including royalties and attorneys fees and related costs in connection with or arising out of any actual infringement of any third party patent copyright or other intellectual property right by the Software or by its use in accordance with this Agreement and documentation PROVIDED THAT a Hemisphere has the right to assume full control over any action claim demand or proceeding b Licensee shall promptly notify Hemisphere of any such action claim demand or proceeding and c Licensee shall give Hemisphere such reasonable assistance and tangible material as is reasonably available to Licensee for the defense of the action claim demand or proc
42. thin ninety 90 days to terminate this Agreement and thereafter Licensee shall cease using the Software Hemisphere will also issue a refund for the price paid by Licensee less an amount on account of amortization calculated on a straight line basis over a deemed useful life of three 3 years LIMITATION OF LIABILITY IN NO EVENT WILL HEMISPHERE BE LIABLE TO LICENSEE FOR ANY INCIDENTAL CONSEQUENTIAL SPECIAL OR INDIRECT DAMAGES INCLUDING ARISING IN RELATION TO ANY LOSS OF DATA INCOME REVENUE GOODWILL OR ANTICIPATED SAVINGS EVEN IF HEMISPHERE HAS BEEN INFORMED OF THE POSSIBILITY OF SUCH LOSS OR DAMAGE FURTHER IN NO EVENT WILL HEMISPHERE S TOTAL CUMULATIVE LIABILITY HEREUNDER FROM ALL CAUSES OF ACTION OF ANY KIND EXCEED THE TOTAL AMOUNT PAID BY LICENSEE TO HEMISPHERE TO PURCHASE THE PRODUCT THIS LIMITATION AND EXCLUSION APPLIES IRRESPECTIVE OF THE CAUSE OF ACTION INCLUDING BUT NOT LIMITED TO BREACH OF CONTRACT NEGLIGENCE STRICT LIABILITY TORT BREACH OF WARRANTY MISREPRESENTATION OR ANY OTHER LEGAL THEORY AND WILL SURVIVE A FUNDAMENTAL BREACH LIMITS ON LIMITATION OF LIABILITY Some jurisdictions do not allow for the limitation or exclusion of liability for incidental or consequential damages so the above limitation or exclusion may not apply to Licensee and Licensee may also have other legal rights which may vary from jurisdiction to jurisdiction BASIS OF BARGAIN Licensee agrees and acknowledges that Hemisphere has set its prices and
Download Pdf Manuals
Related Search