READYKEY pIPer Serial Ethernet Unit
Contents
1. e MKII CNC Ver 2 34 and later For more information on the Central Network Controller see READYKEY K6100 K6300 CNC II Install Manual P N 46512 and the READYKEY K6100 K6300 CNC II User s Guide P N 48569 e READYKEY K2100 Series Door Controllers Ver 3 37 and later For more information on the READYKEY K2100 Series Door Controllers see READYKEY K2100 1100 Install Manual P N 74 06964 000 B PAC P N 17111 and the READYKEY K2100 1100 User Manual P N 74 07069 000 B PAC P N 17117 e READYKEY K2200 Series Door Controllers Ver 1 05 and later For more information on the READYKEY K2200 Series Door Controllers see READYKEY K2200 Series Installation Guide P N 46513 and the READYKEY K2200 User Guide P N 47491 Network To ensure effective operation of the plPer on a LAN or WAN the following requirements must be fulfilled Ethernet The plPer units require a 10baseT twisted pair RJ45 Ethernet connection to the local network There is no BNC 10base2 alternative and no token ring version available IP Address A fixed IP address is required for each unit DHCP or BOOTP is not supported Before configuring any of these devices an IP address along with subnet mask and default gateway or router should be provided by the network administrator If the plPer units are to operate on the same subnet the default gateway is not required WAN Issues These devices use UDP as their communications protocol On complex networks or o2. number of the Enter Port number a unit Example 9 Select Source Port of Link 1 or 2 Enter the timeout value Press Enter to accept the default value Press S to save this setting 5 4 2 2 Configuring the Destination Unit Door Controller side The destination unit requires no further configuration 5 4 2 3 Configuring Readykey for Windows for Direct Connection In Installer Sites 1 2 3 The Site Type should be set to either Direct RS232 single door controller or Direct RS232 Cluster master door controller with up to seven slaves The Baud Rate should be set to 9600 The CNC Port Number should be set to 1 2 or 3 depending on the port the plPer is connected 5 4 2 4 Configuring the Door Controller for Direct Connection 1 2 3 The System Type should be set to 2 The Baud Rate should be set to 9600 The Connect Modem should be set to N plPer Serial Ethernet Unit Installation Guide 2002 Radionics Page 7 17408 v1 1 46833C 2002 Radionics a division of Detection Systems Inc 17408 v1 1 46833C 6 02 PO Box 80012 Salinas CA 93912 0012 USA Installation Guide plPer Customer Service 800 538 5807 Page 8 of 8
3. 1 46833C plPer Serial Ethernet Unit Installation Guide Page 4 2002 Radionics plPer 5 3 2 Setting the IP Address Contact your network administrator to receive an IP address e g 192 168 1 51 a default gateway e g 192 168 1 254 and a subnet mask e g 255 255 255 0 Change IP numbers Select option 7 Enter IP Numbers from the The units IP no is 192 168 4 12 Configure Unit menu The default gateway IP no is 192 168 4 1 to display Example The subnet mask is 255 255 255 0 4 1 Change IP no To enter an IP 2 Change Router IP no number router IP 3 Change Local Net Mask number or to change the local net mask Example 4 plPer Change IP numbers menu enter 1 2 or 3 respectively Note Any plPer unit that is connected to the network can be configured provided it has had a valid IP address set or it is on the same IP subnet 5 3 3 Setting the Unit Name Select option 5 Rename Unit from the Configure Unit menu to display Enter new unit name Example 5 ENTER NEW UNIT NAME ESC ROOT MENU Example 5 New Unit Name Enter the plPer name 5 3 4 Setting the Unit Password Select option 6 CHANGE PASSWORD Change Password from the Configure Unit menu to display Enter new pass word for unit PIPER Example 6 ESC ROOT MENU New password gt Enter the new password Example 6 Change Password plPer Serial Ethernet Unit Installation Guide AQd Moo 2002 Radionic
4. C to serial port 2 of the plPer 5 1 Configuring the Communications Program Before connecting to the plPer ensure that the communication program is set to e 9600 baud e No parity e 8 data bits e 1 stop bit No other settings need to be changed Note 2002 Radionics The cable provided that is used to connect the CNC to a plPer can be used to connect the plPer to the PC plPer Serial Ethernet Unit Installation Guide Page 3 17408 v1 1 46833C plPer 5 2 Root Menu When connected type PIPER ROOT MENU to display the Root menu Set up Link Example 1 Configure Unit Note Press S to save changes nr POE o made before exiting this aare Ors ae aa MEU S Save settings ESC Quit without save Enter selection Example 1 plPer Root Menu 5 3 Basic Configuration for all plPer Units Both the source unit the plPer connected to the CNC and the destination unit located at the door controller need to have the following options configured e Serial Ports e IP numbers IP address subnet mask and default gateway e Name e Password To do this 1 From the Root menu select option 2 Configure Unit 2 Enter the name of the unit or its IP address if it is being configured for the first time or it has been reset to factory defaults enter its default name PIPER 3 Enter the CONFIGURE UNIT 192 168 4 12 password for the unit if it is being 1 Set serial port 1 named porti destination port fi d for
5. READYKEY plPer Serial Ethernet Unit Installation Guide 1 0 Description The plPer is a unit that allows an RS 232 signal to be carried over an Ethernet network which makes it ideal for connecting Readykey door controllers to a Central Network Controller CNC by using an existing Local Area Network LAN or Wide Area Network WAN For more technical information see http Awww mutek co uk piper htm 2 0 Modes The plPer unit has two modes of operation modem recommended and direct connection 2 1 Modem Mode In modem mode the plPer acts as a Hayes compatible modem which allows Readykey site programming and configuration to be performed in the same way as similar sites connected by a dial up PSTN modem Figure 1 shows a modem mode configuration The benefit of this arrangement zee lies is that up to 127 sites can be supported with one CNC Since this is a modem based system 12 12 plPer Unit 1 2 the same CNC limits of 32 sites with up to 8 door controllers and 95 sites with a single door controller apply Like the standard dial up system the modem mode connection is not permanent and there will be delays in getting updates to the sites and events returned from the site Dial back is supported which eas allows alarm events to be sent one back immediately to the CNC CNC Figure 1 plPer Modem Connection 2 2 Direct Connection Mode Direct connection mode is used to create a per
6. manent serial link between a CNC and a door controller This allows a maximum of three sites each using a plPer serial port consisting of up to eight door controllers to be supported by one CNC For more information on the Central Network Controller READYKEY K6100 K6300 CNC II Install Manual P N 46512 and the READYKEY K6100 K6300 CNC II User s Guide P N 48569 Z WHEN USING plIPer IN THE DIRECT CONNECT MODE IF THE UNIT CONNECTED TO THE CNC LOOSES POWER THE COMMUNICATION LINK WILL NOT BE ESTABLISHED AGAIN UNTIL POWER FOR THE UNIT AT THE CONTROLLER IS CYCLED IT IS STRONGLY ADVISED THAT THE POWER IMPORTANT FOR UNIT CONNECTED TO THE CNC BE FROM A U P S OR OTHER FORM OF STANDBY POWER 17408 v1 1 46833C A member of the radionics Bosch Group plPer 3 0 3 1 3 2 3 2 1 Note 3 2 2 3 2 3 needed at the CNC The advantage of a permanent Figure 2 shows three sites a connected to a CNC and since Door Controller each plPer unit has two serial M ports only two devices are m il E connection maintained 12 between the central point and the remote sites is that 12 updates i e changes to the plPer Unit system and events are e communicated immediately e g alarms appear at the central PC with a minimum of delay 1 2 plPer Unit CNC Figure 2 plPer Direct Connection Requirements Hardware and Software The plPer works with following equipment and software
7. n links that may need to cross firewalls it should be verified that a UDP connection can be established between devices plPer Serial Ethernet Unit Installation Guide 17408 v1 1 46833C Page 2 2002 Radionics 4 0 Installation Connect the plPer units as shown in the Figure 3 Note 1 All connections shown are solder side view or terminal connection view Note 2 CTS and DTR are not connected at the door controller as this is linked at the CNC plPer PC CNC PC CNC RS 232 Connection 9 way female D type 2 3 4 Sz Door Controller n states Rulsetes 7 e AE 5 way terminal block GND DTR RX CTS TX RS 232 9 6 7 6E 9 8 7 6 plPer RS 232 Connection plPer RS 232 Connection 9 way male D type 9 way male D type plPer Network Connection 10baseT Figure 3 PC CNC amp plPer Connections plPer Network Connection plPer Unit 1 plPer Unit 2 Red Red Blue fee White J Table 1 PC to CNC Pinouts 3 Ble _ 6 e el CH w e 2 Red i Receive RX__ Not connected 6 Notconnected _ 7 linrkto8g J 8 linkto7 J 9 Notconnected _ Table 2 plPer Pinouts 5 0 Configuration Before the plPer mode is set first configure the plPer units to do this will require a PC a communications program e g Tera Term Pro which is available from http www vector co jp authors VA0024 16 teraterm html and a serial port connection from the P
8. ring the Source Unit CNC Side 1 Select option 3 Modem Emulation AT commands 2 Select option 4 Modem Emulation Turn auto answer off enabling AT commands and auto answering a function that the CNC does not require The Embedded Commands menu will now display see Example 8 Configuring the Destination Unit Door Controller side Select option 3 Modem Emulation AT commands enabling AT commands and auto answering a function that the door controller unit requires The Embedded Commands menu will now display see Example 8 IP Addresses as Telephone Numbers The Telephone Number is based on the IP address of the door controller plPer e Any number in the IP address which is less than 100 is made up to 3 digits by inserting O zero on the left hand side e g 123 32 4 32 becomes 123 032 004 032 e All full stops are removed from the new number e g 123 032 004 032 becomes 123032004032 e Finally letter P followed by the plPers port number 1 or 2 is added to the end of the number e g 123032004032 becomes 123032004032P2 Readykey for Windows Settings In Installer Sites 1 The Site Type should be set to either Modem single door controller or Modem Cluster master door controller with up to seven slaves The Baud Rate should be set to 9600 The CNC Port Number should be set to 1 2 or 3 depending on which port the plPer is connected Enter the required Duration which is the maximum time the Network Ma
9. s Page 5 17408 v1 1 46833C plPer 5 4 5 4 1 5 4 1 1 Note 5 4 1 2 Note 5 4 1 3 5 4 1 4 5 4 1 5 5 4 1 6 5 4 1 7 Configuring Modes Dial Up Connection For this configuration both plPer units need to be set to accept AT commands To enable the use of AT commands follow the instructions in Sections 5 4 1 1 and 5 4 1 2 Change the Trigger Character The plPer trigger character which is used to enter the command mode by default is set to but since the character is used by modems it will need to be changed 1 Select option B Change menu trigger character Change Trigger Character from the Configure Unit menu to display Example 7 Current character is Enter new trigger character gt CR none Example 7 Changing menu trigger character 2 Type the character you want to use It is recommended that you use the forward slash character To return to the Root Menu you must use the newly defined trigger character Enabling Embedded Commands If you have not changed the trigger character you will not be able to set AT command mode 1 Select option A Embedded Commands Embedded Commands from the ia Unit ogc E E T EE menu to alsplay Modem emulation AT commands Example 8 Modem emulation Turn auto answer off The embedded commands to be enabled depend on the type of unit being used Change arming string Save Previous Menu Example 8 Embedded Commands Configu
10. ster will stay on line to the site Enter the Dial Times required These are the times in 24 hour format when the CNC will automatically dial the controller 6 Enter the Telephone Number Refer to Section 5 4 1 5 above for more details OL a NY Door Controller Settings 1 The System Type should be set to 2 plPer Serial Ethernet Unit Installation Guide 17408 v1 1 46833C Page 6 2002 Radionics el ae es us plPer The Baud Rate should be setto 9600 Connect Modem should be set to Y Dial Back should be set if required Option 2 The phone to be dialed should be entered see Section 5 4 1 5 above for more details 5 4 2 Direct Connection 5 4 2 1 Configuring the Source Unit CNC Side 1 2 f 8 9 From the Root menu select option 1 Set Up Link Enter the IP address of the source unit you can enter the name but it is recommended that IP addresses are used Enter the units password A menu similar to Unit IP 192 168 4 12 named DC1 MAC no 00201D004681 V420K Port name gt portl is a destination port Example 9 will be i Port name gt port2 is a destination port displayed Port name gt port3 is a destination port Enter the port Digital INPUTS are not linked number of the Select Source Port of Link source unit 1 or 1 Serial port 1 2 2 Serial port 2 3 Parallel port 3 Enter the IP 4 Digital inputs address of the destination unit Enter the port ESC ESCAPE
11. th 2 Set serial port 2 named port2 destination port con oe 2e e 3 Feature not present Set parallel port first time or it has 4 Feature not present Set relay I O port been reset to 5 Rename Unit DC1 factory defaults 6 Change Password enter PASS as a 7 Enter IP numbers 192 168 4 12 192 168 4 1 255 255 255 0 password 8 Packet send values 100ms from last char 256bytes Char none 9 Reset to Factory Defaults The Configure Unit A Embedded commands AT commands ON Auto answer ON menu is displayed B Change Trigger character Example 2 S Save settings Note Press S to save P Return to previous menu changes made before ESC ROOT MENU exiting this menu Enter selection gt Example 2 plPer Configure Unit Menu 5 3 1 Configuring Serial Ports Select option 1 or 2 from the Configure Unit menu to display Example 3 The only settings that PORT CONFIGURE need to be altered Port named portl is setup as No handshake are 9600 Baud No Parity 2 Stop bits and 8 Data bits Option 2 Stop Character delay none stop bits which ee needs to be ee hanged to 2 oe ae change 3 Parity e Option 5 4 Data bits Handshake 5 Handshake which needs to 5 ISMN BEE be changed to 6 7 8 channel receiver None pIPer 8 Output delays only S Save settings P Previous Menu ESC Root Menu Example 3 plPer Port Configure Menu Note Press S to save changes made before exiting this menu 17408 v1
Download Pdf Manuals
Related Search