Fingerprint Deadbolt System
Contents
1. The motor driving sound of the Deadbolt unlocking and a triple beep sound indicate successful unlocking amp The lock will automatically engage within 5 seconds of the door being closed once you have entered amp Just a double beep sound and a red light indicates an error Please check your User Access Code and try again 2 3 2 with fingerprint Step 1 Pull up the sliding cover which turns on the keypad backlighting amp If the keypad backlight is not on or turns off then press to turn it on again before proceeding If it will not turn on at all then the manual lock lever on the back body is in the LOCK position and you cannot enter until it is moved to the UNLOCK position Step 2 Place an enrolled finger flat on the glass of the fingerprint sensor The red sensor light indicates the finger is being scanned and compared to the stored template This should take less than 1 second The motor driving sound of the Deadbolt unlocking and a triple beep sound indicate successful verification and access granted If there is no reaction and the red sensor light remains on then another verification is required Lift your finger off and then place it back flat on the sensor glass If this does not work then go back to Step 1 and try again with the same or another enrolled finger amp The lock will automatically engage within 5 seconds of the door being closed once you have entered Just a double beep2. box should be within Open Close button 10mm 4 Maintenance This is a high tech electronic device It is highly recommended that all repairs are done by authorised persons only Failure to comply could void your warranty Keep the sensor surface clean and dry Wipe gently with a clean soft dry cloth to remove any dirt residues stains or moisture amp A low battery warning alarm will sound when the batteries run down to less than 30 of full power You should then replace all of the batteries with a new set as soon as possible amp If you do not change the batteries in time or mix old and new batteries causing rapid power loss and the lock ceases to function then you can place a 9V square battery on the terminals at the base of the front body to provide temporary power Your fingerprint records are not lost You can enter using an enrolled fingerprint and then change the batteries The batteries supplied with the lock may suffer some power loss during storage and transit prior to sale and will be subject to heavy use during initial testing and enrolment They may need to be replaced sooner than normally expected o Basic Troubleshooting Forget User Access Code Check with administrator for User Access If no record exists you must change access Code records Refer to 2 1 1 code again If the lock does not recognize a Was the fingerprint properly placed in the Try again by putting the fingerprint in the cent
3. Sensor On mode This means that the fingerprint sensor will be turned on only when the initiation sensor detects a finger being placed on the sensor glass However if the lock is in direct sunlight which is stronger than the light emitted by the initiation sensor then the finger may not be detected and the fingerprint sensor may not turn on In such cases the automatic Fingerprint Sensor On mode can be set so that the fingerprint sensor automatically turns on when the keypad is backlit slide cover up or press This mode is recommended for locks installed in strong direct sunlight Note Permanent use of the automatic Fingerprint Sensor On mode may slightly reduce battery life 2 6 1 How to set automatic Fingerprint Sensor On mode Step 1 Open battery cover and press N button LED displays PO xx Picture will be changed to show the action correctly Pressing N button Step 2 Pull up sliding cover and press 6 and LED displays P6 A triple beep is heard which indicates success of the programming xx Picture will be changed to show the action correctly 2 6 2 How to cancel automatic Fingerprint Sensor On mode Step 1 Open battery cover and press N button LED displays PO xx Picture will be changed to show the action correctly Pressing N button Step 2 Pull up sliding cover and press 7 and LED displays P7 A tr
4. sound and a red light indicates an error Please check your fingerprint and try again 2 4 Unlocking the door from inside Note The manual lock lever on the back body must be in the UNLOCK position in order to unlock and exit from the inside Method 1 Push Open Close button on back body The motor driving sound of the Deadbolt unlocking and a triple Beep sound indicates successful unlocking amp If you push the Open Close button again the deadbolt will lock Method 2 Turn the knob on the back body to the OPEN position by manual force The Deadbolt will remain unlocked Permanent Unlock Mode until the knob is manually turned back to the CLOSE position 2 5 Temporary Unlock Mode This lock is pre set in Automatic Locking Mode After being electronically opened it will automatically lock within 5 seconds of the door remaining in or returning to its fully closed position However you can set a Temporary Unlock Mode to enable free access without the use of fingerprints or User Access Code For example this is useful for storeroom and office doors that need to remain unlocked during office hours amp Note The manual lock lever on the back body must be in the UNLOCK position 2 5 1 How to set the temporary unlock mode Step 1 Unlock using your fingerprint or User Access Code and open the door so that you have access to the front and the back of the lock at the same time Step 2 Open batte
5. Fingerprint Deadbolt System Model FDL 510 Installation and Operation Manual Thanks for choosing fingerprint deadbolt from Fingcas Please read this manual carefully before starting operation Please keep this manual for further reference later Fingcas Corporation www fingcas com Table of Contents 1 Introduction ssrssssssnnnnnnnnnnnunnnunnnununnnnnnnnnnnnnnnnnnnnnnnnnnnnmmn a 3 1 1 Product Concepts Pree eee eee eee eee eee eee eee eee 3 1 2 Package Contents s ssss usususunuuuununnunununnunnnunnnnnnnnnnnnnnnnnnnnn n 4 1 3 Description of Components amp Exploded View ssrrrttttttresesseeeeeseneneens 4 1 4 Technical Specification EPP 5 2 Programming Pree eee rere eerie eee eer eee eee eee eee 6 21 User Access Code PIN Code Pree eee eee eee eee 6 2 1 1 How to enroll change User Access Code Pree teeter iret rrr rrr rrr rrr rr 6 2 2 Fingerprint Enrollment cy T 221 How to enroll your fingerprint TEETETEETETETEELEEEEETCELEEEELELELELELLELECELELLELECECET T 222 How to delete enrolled fingerprints eer 8 2221 Delete single fingerprint from lock r rssssssssnsunununnununnnnununnununnnnunnnnnna 8 2 2 2 2 Delete all fingerprints from lock ere re errr errr rrr rrrrrerrerr rrr rrr rrr rrr rire ire 9 2 3 Unlocking the door from outside s ssssssss s us uuusunuununununnununnnna 10 2 3 1 with User Access Code ssssssss usuuunununnununnunununnunununnununnnnnuunnunnnnnnnnnn 10 2 3 2 with Fingerprint Pere r
6. Pull up sliding cover LED displays FO Step 3 Press 1 and button LED displays F1 and changes soon to display ID number for the next fingerprint enrollment The fingerprint sensor will then turn on with a red light F1 displays in LED ID number displays in LED and red sensor light turns on amp ID numbers for fingerprint enrollments start at OO ends 98 They are automatically assigned in sequence as you enroll each new fingerprint Please record the ID number and personal details for each fingerprint enrolled The correct ID number will be needed when deleting an individual fingerprint Refer to 2 2 2 for Deletions Step 4 As soon as the red sensor light turns on place your chosen finger flat on the glass of the sensor When the red sensor light turns off lift your finger and quickly place it back on again The red sensor light will turn on and then off once more to complete the second scan of that same finger A triple beep sound indicates Place finger twice the success of that enrolment To continue enrolling more fingerprints or to try again if unsuccessful press and then repeat Step 4 To achieve maximum convenience and flexibility we recommend you enrol several fingers from each hand Correct Fingerprint Placement lt Fingerpnnt Placement gt 2 2 2 How to delete enrolled fingerprints 2 2 2 1 Delete Single Fingerprint from Lock Step 1 Open batt
7. er fingerprint center of the sensor of the sensor If the sensor light does not come on Batteries may not be installed correctly or Use 9V square battery held against terminals at If Keypad does not work may be run down base of the front body to gain access If the sensor light does not come on Manual Lock Lever on the Back Body may Manual Lock Lever has to be moved to the If Keypad does not work be in the LOCK position UNLOCK position by someone on the inside If 9V battery does not work Red indicator flashes with double Invalid or deleted fingerprint Fingerprint Place an enrolled and unobscured fingerprint beep sound and door can not be covered obscured or poorly positioned correctly on the sensor opened LED Display a L T Er General error Use correct User Access Code or finger in correct position 6 ID Number and Fingerprint record Record each ID number its date of enrollment and a fingerprint description for future reference
8. ere errr reer reer ree eee eee ree eee 10 24 Unlocking the door from inside ssssssss uuununuunununuununununnunnnn 11 25 Temporary Unlock Mode sssssss susununununununununununununununnnnnnnnnnunnnnn 11 25 1 How to set the Temporary Unlock Mode sssssss usu u 11 2 5 2 How to delete the Temporary Unlock Mode 55sssssssssrrrrrrrreeere 12 26 Automatic Fingerprint Sensor On Mode sssss s ssusuuuuuunununnunun 12 2 6 1 How to set automatic Fingerprint Sensor On Mode srvrrsrrsssereeeeeeees 13 2 6 2 How to cancel automatic Fingerprint Sensor On Mode 5e 13 27 Programming Summary Tabl e We 13 3 Installation of the lock sssssssssssnsunununnunununnununnunununnununnnnununnunununnnnnn 14 3 1 Checking before installation rsssssssssnsnnununnunununnununuunununnunununnnnnnnn 14 3 2 Installation template Pere ee errr eer ere re ree eee eee eee eee eee eee 14 3 3 How to install ANd test sssssss susununununununununununununnnnnnnnnnnnnnnn 15 4 Maintenance Meee re 16 5 Basic Troubleshooting Peer re reer rere eee eee eee eee eee 17 6 ID Number and Fingerprint record sssssss u unuuununununnnnununnnunnnnnnnn 18 Please read this manual carefully before operation If any problem occurs or if you need further instruction or assistance please contact your Fingcas Dealer 1 Introduction 1 1 Product Concepts Designed for User convenience No more ke
9. ery cover and press D LED displays FO F2 displays in LED Step 3 Enter the ID number 2 digits of the enrolled fingerprint you wish to delete and then press A triple beep sound and a green light indicate a successful deletion Press ID Number 2 digits and amp To continue deleting individual fingerprints keep repeating Steps 2 and 3 2 2 2 2 Delete all Fingerprints from Lock Step 1 Open battery cover and press D LED displays FO FQ displays in LED F3 displays in LED i Step 3 Enter User Access Code PIN Code and then press A triple beep sound and a green light indicates successful total deletion Press PIN code and amp You can delete all enrolled fingerprints but User Access Code will remain undeleted in this mode 2 3 Unlocking the door from outside Note The manual lock lever on the back body must be in the UNLOCK position for external Authorised entry to work 2 3 1 with User Access Code PIN Code Step 1 Pull up the sliding cover which turns on the keypad backlighting If the keypad backlight is not on or turns off then press to turn it on again before proceeding If it will not turn on at all then the manual lock lever on the back body is in the LOCK position and you can not enter until it is moved to the UNLOCK position Step 2 Enter User Access Code PIN Code and then press
10. idity 45 RH 80 RH Safety Standards FCC CE Battery life Approx 12 months 20 times day 2 Programming The function buttons used for programming are hidden by the battery cover on the back body This means that only people authorised to be on the inside and with knowledge of the lock programming will be able to add delete change data and settings The door will need to be open when programming in order to give access to the front and back of the lock 2 1 User Access Code PIN Code 2 1 1 How to enroll change User Access Code Each lock comes with the factory default User Access Code of 0000 For your own security you are recommended to immediately change it to a User Access Code of your own choice 4 to12 digits and also to consider changing it at various intervals in the future Step 1 Open battery cover and press N button Sept 2 Pull up sliding cover LED displays PO Step 3 Press 1 and LED displays P1 Step 4 Put in your own PIN code 4 12 digits and then press Put your pin code 4 12 digits and Step 5 Do Step 4 again double entry is required A triple beep sound and a green light indicates successful programming When you set a new User Access Code the previous one will be automatically be deleted 2 2 Fingerprint enrollment 2 2 1 How to enroll your fingerprint Step 1 Open battery cover and press D button Step 2
11. iple beep is heard which indicates success of the programming xx Picture will be changed to show the action correctly 2 7 Programming Summary Table Deiete Temporary Unlock mode The following is a list of function codes 2 ID and Delete single fingerprint by ID 38 PIN and F 2 Pe and P8______ Setutomatc Fingerprint Sensor onmo Cancel automatic Fingerprint Sensor On mode D C 2d 3 Installation of the lock 3 1 Checking before installation You will need Hole cutter 32 35mm Door Thickness must between 32 60mm for 50 60mm thickness longer connecting screws are needed Checked for right or left handed positioning Electric drill 8mm drill bit Phillips screwdriver Left Hand Right Hand This product can be used for either left or right handed doors 3 2 Installation Template Template cvm Both sid amp Fire prevention open door door Right Handed Both sid Fire prevention open door door Left Left Handed Handed l mark the center and Should be kept the distan e cut the Hole 32 35mm within 10 mim 2 4mm screw hole www bioenter co kr 3 3 How to Install and test 1 Put the template on the inside of the Neoptera es NOs onda 2 Mark the centre of the hole cut out and make arenai omora eroro panded a guide hole with the 3mm drill bit Then use the door We recommend dacement Oem hole cutter centred in the guide hole t
12. o complete the cut out above your cylinder lock handle 3 Take the cable connectors and strap on the front body from the outside through the cut out hole and then through the gap in the back body plate on the inside damaged when screws are applied 5 Fix the back body plate to the door with its leading edge flush with the outer edge of the door use 5 of the 18mm screws 7 Fix the back body to the back body plate using one 20mm screw at the end of the battery box and two 8mm screws in the leading edge 4 Push the cylinder of the front body into the cut out hole and keep light tension on the strap from the inside Fix the back body plate to the front ma 4 Caution Please be careful cables are not pinched and do not get 6 Join the connectors on the strap to the connectors on the back body Please note pin placement to get correct orientation and make sure that 10 pin connects to 10 pin and 11 pin connects to 11 pin 8 Place plastic height adjustment jig s under the Deadbolt box sufficient to make its height align with the height of the back body when the door is closed and the Deadbolt box is mounted on the door jamb Then fix the Deadbolt box and jig s to the door jamb using at least two 20mm screws 9 Put the batteries into the 10 The distance between 11 Close the battery cover battery box 1 5V AA x 4 pes in right polarity back body and Deadbolt and test the lock
13. proving battery life and sensor efficiency Applications Stand alone deadbolt lock for houses apartments villas offices meeting rooms storerooms etc 1 2 Package Contents gt 87 Front Body Back Body Back body plate Deadbolt box amp Height adjustment jig Bolts and screws Batteries User s manual 1 3 Description of Components amp Exploded view Description of Components Front Body Back Body Cead Bolt pen Botion Samon Display Fingerpont control barion 12 Kapo Poseword contra bution Battory Tray Finger Pant Sensor Led Display Green Boece IK Fed Am Derry Eaker Cover ASSEMBLY DIAGRAM n a e Door frame HE GEE EO i Le 3 5 a Oe EOTS a f Ly Door frame deadboot bracket Nie l AE O gt E Inner body back cover al Sx 20 mm bokt x 2 4 20 mm bot x 1 4 4mm bolt x 2 4x 18 mmscrem x 9 Inner body 1 4 Technical Specification Jtem Technicalparameters 9 twice to get on fingerprint template User Capacity up to 99 fingerprints 1 N Infrared Sensor applied Supply Voltage DC 3 3V DC3 8V 1 5V AA x 4 Alkaline battery Emergency Power Source Terminal for 9V square battery LED Display ID Number indicator 00 98 Thickness of the door 32mm 60mm Body Zinc alloy die casting Battery Cover Strengthen Plastic Front Body 70 w x 160 h x 36 d mm Back Body 78 w x 160 h x 38 d mm Operating Environment Temperature 20MC 75 amp C Hum
14. ry cover and press N and LED displays P0 A long beep sound is heard which indicates success of the programming Step 3 Pull up the sliding cover and and press 2 and LED displays P2 A triple beep sound is heard which indicates success of the programming To cancel the Temporary Unlock Mode pull the sliding cover up and then down The motor driving sound of the Deadbolt locking and a triple beep sound indicates success To stop temporary unlock mode you pull up the sliding cover and down at any time and the door will be locked with motor driving noise you can not open the door without your fingerprint verification To re activate the Temporary Unlock Mode simply unlock using your fingerprint or User Access Code The lock will then remain in the unlocked position until the Temporary Unlock Mode is cancelled again or deleted 2 5 2 How to delete the Temporary Unlock Mode Step 1 Open the door so that you have access to the front and the back of the lock at the same time Step 2 Open battery cover and press N LED displays PO LED displays P3 A triple beep sound is beard which indicates success of the programming amp Then close the door and the Deadbolt will automatically lock within 5 seconds of closing Automatic Locking Mode has been re activated 2 6 Automatic Fingerprint Sensor On mode This lock is pre set in the manual Fingerprint
15. ys cards or remotes The ultimate convenience of nothing to carry forget pass on be duplicated or to have stolen Plus very easy and quick to enroll and to verify fingerprints Highest Security Level Fingerprint based identification is the oldest and the most reliable among all the biometric technologies because your fingerprints are unique and invariable throughout your lifetime Small and slim design Palm size front body with 36mm thickness powered by 4 AA alkaline batteries Easy Installation and Operation Requires one hole to be drilled to install and simple steps for enrollment deletion of ingerprint User Access Code Sufficient fingerprint capacity 99 fingerprints can be enrolled Auto Locking and temporary open mode User can set up auto locking or temporary open mode Audible and visible indicators LED light and buzzer sound indicates operation results Emergency User Access Code and terminals for external power source User Access Code can be used in case your enrolled finger are injured or to allow others emergency access A 9V square battery can be used externally to provide power if the internal batteries are run down Built in Alarm A loud alarm sounds when the door is opened by force Sleep mode and initiation sensor The lock powers down when no in use In manual Fingerprint Sensor On mode the infrared initiation sensor will wake up the fingerprint sensor when a finger is placed on the sensor glass thus im
Download Pdf Manuals
Related Search