User`s Manual
Contents
1. 4 5 FALSE SIGNALS A false signal occurs when something that shouldn t sound like a good target Your Deep Target does an excellent job of ignoring junk targets with similar electrical characteristics Large pieces of trash for example or ever some kind of bottle caps and pull tabs Small pieces oftrash lessthan 2 inches from the search coil will also sound good occasionally False signals normally very faint or very abrupt with static Often when you go back over the same spot a false signal will simply disappear Other false signals may be very loud and sharp but most of these will disappear if the coil is speeded or raised slightly Some shallow large or irregular pieces of junk however will fool the Deep Target no matter what you do Here s some other sources of false signals and what to do about them 4 5 1Detector Interference Caused by nearby metal detectors operating at the same or close frequency solutions Move further away or reduce sensitivity 4 5 2 Electrical Interference Caused by Radio TV stations power lines etc solutions Move further away lower the sensitivity reduce sweep speed Wrap the search coil cable tightly around the stem 10 4 5 3 Highly Mineralized Soil Usually causes constant static or good target sound solutions Lower the sensitivity increase the discrimination Raise the search coil until false signals disappear and sweep atthe height 4 5 4 Wet Sand2. User s Manual Deutsche Anleitungen finden Sie zum Download auf http www seben com manuals Per il download delle istruzioni in italiano cliccate qui http www seben com manuals Puede descargar las instrucciones en espanol aqui http www seben com manuals Vous pouvez telecharger la notice en francais sur http www seben com manuals www seben com Attention Please read before assembling Important information for preventing damages upon assembly Before delivery the metal detector is tested and measured to guarantee full functionality Assembling the metal detector wrong or overhasty can damage or sever the interior cables Therefore please assemble it slowly and carefully Reparations of defects caused by wrong assembly will be made at the owner s expense Thus please especially take care that the upper and lower part of the shaft are connected correctly the cut out on the lower part has to face upwards into the direction of the controlling unit which can be found on the upper part of the shaft This cut out shall protect the cables in the shaft from being severed or damaged The parts have to be pushed together in their correct position If you do not mind this small but nevertheless important fact you may damage the cables This may lead to malfunctions of the detector e g loose contacts or even non function To check whether the cables are cut or damaged please remove the controlling unit by releasing
3. the small screw Detailed instruction how to assemble the Deep Target metal detector e Remove the big plastic headed screw 1 on the upper part of the shaft A e Release the small screw 2 which connects the upper part of the shaft with the controlling unit C slightly but not completely e Connect both ends of the cables and mind the correct assembling of plug and socket 3 Small arrows on both point out in which position they are connected correctly Wrong assembling may damage the cables e Let the lower part of the shaft B slide slowly onto the upper part in direction of the controlling unit Mind the position of the cut out as written above The cables run through this spot of the upper shaft part to the controlling unit 5 Wrong positioning of the parts while assembling will damage the cables e After you connected both shaft parts correctly tighten the small screw 2 than refit the big plastic headed screw into the hole on the rearside 6 and tighten it as well Please adjust the length of the lower stem so that you can stand upright with the detector in your hand In doing so the search coil should be hold 2 cm over the ground Then turn the stem lock nut in reverse direction until the stem 1s fixed After that please align the search coil to the ground The search coil should always be aligned parallel to the ground If necessary the armrest can be aligned as well In order to do that please unscrew the screws
4. old batteries by fresh batteries Do not mix old and new batteries different types of batteries standard alkaline or rechargeable or rechargeable batteries of different capacities Never attempt to recharge the non chargeable battery 6F22 or SOO6P 9 volt battery is normally non rechargeable Dispose old batteries promptly and properly 3 3 BATTERY TESTING The batteries should be tested after initial batteries installation The batteries should also be tested if the detector does not turn on has weak volume cannot tune properly or drifts or has erratic operation SENS dial Note You are recommended to test the batteries every time you use your detector To test the batteries turn the DISC rimination dial clockwise at any position Then set the SENS itivity dial anti clockwise until a click sound is heard A loud tone indicates good batteries A faint tone indicates weak batteries and no tone means that it s time to change 3 4 USING HEADPHONE You should always use a headphone whenever you search with your metal detector Headphone is especially useful in noisy area such as the beach and rear city area ltenhances audio perception by bringing the sound directly to your ears while masking outside noise interference You shall be amazed at how much better you can hear the detector signals with the headphone than you can with the speaker alone Using headphones alsosave battery power To
5. ash with your or if you can take it all Always fill in your holes neatly whether you re in a city park or remote wilderness Leave the land as it was before you disturbed it Always obey all laws relating to Treasure Hunting Always return valuable property if you can locate the original owner Always do what ever you can to give the hobby of Treasure Hunting the good image it needs and deserves 1 3 PLACES WHERE YOU CAN USE YOUR METAL DETECTOR National Forrest and Federal lands State park and Lands Corps of Engineers Lakes shorelines and lands Bureau of Land Management BLM Lands City or Country Park Lands and public school grounds Structure change to be continued with 3 2 Installing Batteries Preparation 3 2 INSTALLING BATTERIES You need 2 9 volt 6F22 SOOGP or equivalent batteries to power your detector 6F22 O Soo6P 3 2 1 Turnthe DISC dial anticlockwise to the OFF position to make sure the detector is off DISC dial 3 2 2 Slide the battery cover away from the BATTERY COMPARTMENT 12 Battery cover 3 2 3 Insert 2 new batteries into the BATTERY COMPARTMENT Cares should be taken for the polarities symbols and which are marked the connection terminals and on the batteries The polarities of the battery must be matched with the polarities of the terminals 3 2 4 Replacethe battery cover Cautions Use only fresh batteries and always replace the
6. connect a headphone to the detector insert the headphones 1 8 inch pluginto the HEADPHONE JACK 8 Note The detector sinternal speaker will be disconnected when you connect a headphone 4 OPERATION 4 1 MODES OF OPERATION The Deep Target has two operating modes i e The searching mode and the targeting mode searching mode when the power is turned on the device defaults at this mode This is a VLF Motion Discrimination mode which automatically ignores most ground minerals rejects junk and works only when search coil is moving Targeting mode when the TARGET RED button is depressed 4 2 SEARCHING MODE 4 2 1 Initial Setting Turn the SENS control dial to the position 8 Turn the DISC control dial to the position 2 For other settings only experience will tell you how much sensitivity and discrimination should be used in a particular situation 4 2 2 General Rules As ageneral rule turn your sensitivity down to reduce excessive false signals caused by highly mineralized ground or interference caused by power lines radio stations etc Turn it up if you want those deepest smallest targets and you re willing to put up with afew more false signals In trashy areas you ll probably want to operate at a higher level of discrimination 6 for example to cut down onthe amountof time you spend digging bad targets In relatively non trashy soil use alow level of discrimination 2 for examp
7. e false targeting signals in highly mineralized soil In this case it is important to keep the coil parallelto the ground and at least an inch above it we B 4 MAINTENANCE Your Deep Target doesn t require a lot of care but there are few things you should do to keep itin peak operating condition If you re not going to use it for a while take the batteries out Avoid extreme temperature like the inside ofa closed car sitting in the sun If you scrub the search coil on the ground you ll eventually ware off the bottom Coilreplacement are expensive Instead invest in an inexpensive coil cover or called the skid plate Put a rain rest cover over the control housing if you re hunting in rain fog or dust Keep your Deep Target dry and clean Wipe off the lower stem before sliding into the upper stem and keep the lock nut threads free of sandand dirt 5 SPECIFICATION 1 BATTERY 2X9V TYPE 6F22 S006P OR EQUIVALENT 2 OPERATING CURRENT STANDBY lt 18mA MAX lt 50mA 3 OPERATING VOLTAGE RANGE 7 9 6V 4 OPERATING FREQUENCY 5 5KHz 5 SENSITIVITY Min 23 cm Test Coin US 25 6 AUDIOFREQUENCY 500Hz T TEMPERATURE RANGE 10 50T 8 SIZE 130mm L x 150mm W x 95mm H 9 NET WEIGHT 1 3Kg
8. e ground Increase the sensitivity level Decrease the discrimination level speed upthe sweep rate slightly 4 4 OPERATION TIPS As stated inthe Note in 4 2 Take Your Time and Overlap yourSweeps Use a good headphone You won t miss faint targets you won t attract unwanted attention and you won t bother others Practice targeting There s nothing sacred about the methods described in this manual ManyDeep Target users have developed their own targeting methods Alway bury a coin when working in unfamiliar territory and check it at different discrimination and sensitivity levels There may be some sensitivity loss at higher levels of discrimination The greaterthe ground mineralization the higher the sensitivity loss For example you may able to detect a penny at 6 inches deep at zero discrimination but no deeper than 4 inches at the pull tab discrimination point The Deep Target is an easy detector to use but if you re having trouble with any aspect of its operation pinpointing searching false signals etc go back and reread the part of this manualrelating to your problem Ifa targetgives a strong response in the search mode but no response in the Zero Motion Targeting mode you may have turn out your target and all others by pushing the TARGET button over another piece of metal If you suspect this may be the case move the search coil to another spot before pressing the TARGET button again
9. est response Now move the coil slowly forward and back a couple of times again stopping overthe strongestresponse Move the coil side to side one more time and stop over the strongest signal once again Your targetshould be directly below the search coil For quick and accurate targeting of strong signals place the coil on the ground very close to the target and push and hold the TARGET button You have now tuned out most of the target signal so that when you raise the coil for targeting you will only receive a response directly over or very nearly over thetarget 4 3 2 Targeting in the Motion Search Operation Targeting inthe search mode will take a little practice but you may find that for most targets it s even quicker than the Zero Motion Targeting Mode simply usethe similar procedure asin Zero Motion Targeting 4 3 1 The only difference will be that when you stop the coil over the target you will lose the audio signal You must keep the coil moving at least slightly to determine the location of the strongest signal before it For very strong signals you may improve your motion mode pinpointing accuracy by adding one or more ofthe following steps Lift the coil until the signal is just barely heard Reduce the sensitivity level Increase the discrimination level Rest the coil on the ground and move IL back and forth very slowly For very weak signals try the followings Move the coil closerto th
10. le In this manner the Deep Target will detect all metal targets within its range and you can instantly increase the discrimination for further identification Keep the search coil moving at a comfortable rate Remember thatthe Deep Target is a motion detector and responds only when search coil or the target is moving while in the searching mode Keep the search coil parallel to and as closeto the ground as practical Overlap your sweeps approximately 50 Search in a methodical manner sweeping in a tight semicircle Pay close attention to where you re going and where you ve been NOTE Take Your Time If you walk too fast you can toverlap your sweeps and you ll miss alot of ground lf you sweep too fast you ll lose sensitivity and miss the deep targets 4 3 TARGETING MODE 4 3 1 Zero Motion Targeting The Target mode requires no tuning no motion detects all metals and in normal soil it s even more sensitive than the search mode Precise target location isa snap Once the presence ofa buried target is indicated by the beep beep of the Deep Target simply place the coil lightly on the ground away from the target area Push the TARGET button and hold At maximum sensitivity you may hear a faint tone which will disappear as soon as the coilis raised Raise the coil one half inch or so and move it side to side across the target area afew times Stop the search coil over the spot where you receive the loud
11. on the back side of the armrest INTRODUCTION Thank you for purchase of the Deep TargetMetal Detector With this powerful and versatile device you can hunt for coins relics jewellry gold and silver just about anywhere To obtain maximum performance we urge you totake a few minutes to read this manual carefully 1 1 ABOUT YOUR DETECTOR Fully Automatic a turn on and go detector Zero Motion Targeting Function for precisely locate a target No Clumsy Slack Cable hidden search coil cable connecting between control unit and search coil avoid entangling and forease ofstem length adjustment Headphone Jack provided for headphone connection Both stereo or mono headphone can be used Volume Control for adjusting the output volume to the loud speaker and headphone Batteries Test lets you test the conditions of the batteries in the battery compartment Waterproof Search Coil lets you use the detector in the shallow water Adjustable Stem lets you adjust the detector s length for comfortable use Armrest amp Stem designed to eliminate strain on forearm Power only two 9 volt batteries are required Built in DC DC converter for prolonging battery life 1 2 METAL DETECTOR OPERATORS ETHICS Below are few basic rules you should follow while using your metal detector Always get permission to hunt on private property Always leave a site cleaner than you found it Take atleast some tr
12. same ashighly mineralized soil 4 5 5 Elongated Ferrous Objects lf you hear two beeps very close together and can t find either one you re probably over a nail or some other long iron object But a very shallow coin or a coin on edge will give the same response solutions In all cases the target will be between the beeps or if you sweep atright angles to your original direction you ll receive asingle beep directly over the target except for the very shallow coin One way to tell the difference between a coin anda nail is to set your discrimination at about 5 Most small nails will be tuned out while most coins will respond witha good smooth signal 4 5 6 Extremely Trashy Soil May result in a constant chatter or snap crackle and pop with assorted hard to find good signals Solution Increase the discrimination level You ll be able to zero in on good targets much closer to junk 4 5 7 Digging Tool lf you re carrying a metal diaaing tool in one hand your Deep Target may sound off each time you swing the coil beneath it solution Hold it behind your back or up above your waist False signals may also occur in the Zero Motion Targeting mode When in this mode theDeep Target detects all metals so you may pinpoint a piece of nearby junk instead of a good target For this reason you should always recheck your target area after recovering any target to insure that you haven t missed anything You may also receiv
Download Pdf Manuals
Related Search