USB-0401 - LevelOne
Contents
1. 3 3 3 Windows Vista 7 Setup There are two ways to install the Win Vista software by using auto install program or thorough the Found New Hardware Wizard Please refer to the following instruction Auto Install Program 1 The Found New Hardware Wizard window pops up Click Cancel to close the window Found New Hardware Windows needs to install driver software for your 88772 Locate and install driver software recommended Windows wil guide you through the process of installing driver software for your device gt Ask me again later Windows wif ask again t nea time you plug in your device or log on 46 Don t show this message again for this device Your devi not function ined you instal dri sofware 2 Insert LevelOne CD Rom to your CD Rom drive Click on My Computer gt your CD Rom drive gt Driver Vista 32 bit press setup icon then it will start to install the driver 3 After complete installation click the Finish button Found New Hardware Wizard 1 The Found New Hardware window pops up Select Locate and install driver software 2 Select I don t have the disc Show me other options Then click Next to proceed EE Feud New Hare Windows needs to install driver software for your 88772 Locate and install driver software recommended Windows wil qude you through the process ofnatl2. USB 0401 USB Gigabit Ethernet Adapter User Manual Ver 1 00 FCC Certifications This Equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning C This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class B for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document
3. you would not have to endure the effort opening PC cases anymore To laptop users it would be even more profitable with the low power consumption feature Together with the high compatibility laptop users are allowed to connect to network easily with lower power consumption and hence strengthen the power efficiency Along with Plug amp Play hot inserting swapping supported the device makes your PC and peripherals being connected in much an easier way 2 2 Key Features Complies with IEEE 802 3 10BASE T standard Complies with IEEE 802 3 100BASE TX standard Complies with IEEE 802 3 full duplex flow control Compliant to USB 1 0 1 1 and 20 standards Powered over USB bus with low power consumption Support fullhalf Duplex operation Support drivers for Windows 2000 XP Vista 7 CE FCC VCCI class B Active LED indicators Plug and Play Installation Support hot inserting and swapping Support Wake on LAN 2 3 LED Definition 2 3 1 10 100 1000M Green 100 1000 M Off 10M 2 3 2 Link Act Green Valid link on this port Blinking Data transmitting receiving Off No valid link on the this port 2 3 3 USB Link Green Valid link with this adapter Off No valid link with this adapter 3 Installation 3 1 System Requirements A Pentium 166 MMX or above processor based any devices that support standard USB One available USB port Microsoft Windows 2000 XP Vista 7 MAC OS 10 3 or 10 4 for 32 bit 64bit x86 an
4. d Power PC based computer A CD ROM Drive 3 2 Hardware Installation Before installation please check if there is an available USB port being enabled To check this you may click My Computer Control Panel System then click the Device Manager tab to check if the Universal Serial Bus controller to be shown on the following list General Device Manager Harcware Proties Pertormance llc Computer BB Dinos adapters SS Floppy coiere SS Hard aci conteoters BB Keyboard E tomers G EB Network adaptere Ports COM E LPT Sitom devices Intel 8237 1AB EB PCI te USE Universal Host Controler USB Root Hub 3 2 1 Connect the adapter to your PC 1 Plug the USB 0401 adapter to your PC 2 Windows will detect new hardware automatically and prompt you for driver For driver installation please refer to the chapter Software Installation 3 2 2 Networking cable installation 1 Connect the UTP Ethernet cable to the network port of the USB Adapter 2 Plug the other end of the cable into a 10 100 1000 Switch or Hub Note You may select the networking cable according to the following information 10 BASE T Category 3 4 or 5 UTP STP 100 BASE TX Category 5 UTP STP 1000 BASE TX Category 6 UTP STP 3 3 Software Installation After attaching the USB to Ethemet adapter to your PC or laptop auto detection for n
5. ew hardware will be activated automatically The procedures to perform driver installation differ slightly from each operation system Please refer to the following paragraphs for detail instruction 3 3 1 Windows 2000 Setup There are two ways to install the Win 2000 software by using auto install program or thorough the Found New Hardware Wizard Please refer lo the following instruction Auto Install Program 1 The Found New Hardware Wizard window pops up Click Cancel to close the window welcome to the Found New Hardware Wizard 2 Insert the CD Rom that came with this product to your CD Rom drive Clickon My Computer your CD Rom drive gt Driver WinXP2K_32bit_ driver Set up then double click the installation 3 After complete installation click the Finish button 3 3 2 Windows XP Setup There are two ways to install the Win XP software by using auto install program or thorough the Found New Hardware Wizard Please refer to the following instruction Auto Install Program 1 The Found New Hardware Wizard window pops up Click Cancel to close the window welcome to the Found New 2 Insert the CD Rom that came with this product to your CD Rom drive Click My Computer your CD Rom drive Driver WinXP 2K 32i diver set up then double click the BB icon to start station 3 After complete installation click the Finish button
6. ing crver software for your device 9 Askmeagain later i le nj rel a yai li bl cag Don t show this message again for this device Your device willect funtion an you install driver software O iom oerte dic tat cae wih your A772 Show other pins 10 3 Select Browse my compuler for driver software Paper 4 Insert the provided diver CD Click the Browse button and select Computer your CD ROM drivebrivervisa 3261 diver WHQL or Vista driver WHOL depends on your system Click Next to proceed 1 n 5 Click the Close button to finish the installation Fett 2S SSTAUSDD Fs ene re 3 3 4 Mac OS Setup Itis not necessary to install driver on Mac10 5 it s plug and play Below are Mac 10 3 or 10 4 installation guideline 1 Insert the provided CD to your CD Rom drive Browse to OSX10 3 or OSX10 4 which depends on your system The install window Pops up Click 12 S Seiner Destinar ink I 2 Select a destination to install the driver on Click Continue to proceed VI 3 Click Install to start installation 13 eon See 5 A mrs Gra 4 Click the Close button to finish the in
7. is not up to date Please check with your local distributors for the latest information part of this document can be Copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2009 All Rights Reserved Table of Contents 1 UNPACKING INFORMATION 2 OVERVIEW 2 1 INTRODUCTION 2 2 KEY FEATURES 2 3 LED DEFINITIO 2 3 1 10 100 1000M 2 3 2 Link Act 2 3 3 USB Linl 3 INSTALLATION 3 1 SYSTEM REQUIREMENTS 3 2 HARDWARE INSTALLATION 3 2 1 Connect the adapter to your PC 3 2 2 Networking cable installation 3 3 SOFTWARE INSTALLATION 3 3 1 Windows 2000 Setup 3 3 2 Windows XP Setup 3 3 3 Windows Vista 7 Setup 3 3 4 Mac OS Setup 4 PRODUCT SPECIFICATIONS 1 Unpacking Information Thank you for purchasing the USB 0401 Before you start please verify that your package contains the following items 1 One USB 0401 2 One driver amp manual CD 2 Overview 2 1 Introduction The USB 0401 provides users to launch Internet via the USB interface up to 1000 Mbps transferring and receiving rate The device is compatible to USB 2 0 1 1 and 1 0 Along with complying 802 3 802 3u and 802 3x standards users are allowed to get connection to network in any environment that encountered What s more
8. stallation eee eene S peream struc mas sucess installed 14 4 Product Specifications Standard IEEEB02 3 10BASE T IEEEB02 3u 100 5 IEEEB02 3x full duplex flow control USBv10 1 1 20 Interface 1 USB port 1 10 10 1000 Mbps Ethernet Port Cable Connections UTP Category 32 55 Network Data Rate 100Mbps 10Mbps LED indications 17 10 100 1000M LinkiAct T USB Link Input power Operating Temperature 40 C 820 1040F Operating Humidity 10 90 non condensing Operation System Windows 2000 Vista 7 MACOS 10 3 10 44 Emission CE FCC VCCI Class 15
Download Pdf Manuals
Related Search