AVR-ISP-MK2 programmer USER`S MANUAL
Contents
1. AV R ISP MK2 programmer USER S MANUAL Revision D January 2013 Designed by OLIMEX Ltd 2012 lead free All boards produced by Olimex LTD are ROHS compliant OLIMEXO 2012 AVR ISP MK2 User s Manual DISCLAIMER O 2013 Olimex Ltd Olimex amp logo and combinations thereof are registered trademarks of Olimex Ltd Other product names may be trademarks of others and the rights belong to their respective owners The information in this document is provided in connection with Olimex products No license express or implied or otherwise to any intellectual property right is granted by this document or in connection with the sale of Olimex products It is possible that the pictures in this manual differ from the latest revision of the board The product described in this document is subject to continuous development and improvements All particulars of the product and its use contained in this document are given by OLIMEX in good faith However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded This document is intended only to assist the reader in the use of the product OLIMEX Ltd shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product This evaluation board kit is intended for use for engineering development demonstration or2. CLICK FOR DOWNLOAD and click RUN in the Operations Flow section 7 Disconnect the AVR ISP MK2 from the USB and connect it again Please refer to 4 2 Arduino AVRDude Linux for more detailed description 5 3 Jumpers description Please note that the two jumpers on the board are PTH plated through hole type 5 3 1 TARGET jumper TARGET jumper controls the powering of the target board If it is in position ON check the diagram on the back of the plastic cover it will provide either 3 3V or 5V to the target board depending on the position of the POWER jumper The default position is OFF Page 14 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual 5 3 2 POWER jumper If you have set the TARGET jumper to position ON POWER jumper controls whether 3 3V or 5V are provided to the target board The default position is 5V 5 4 LEDs explained There are two 3mm LEDs ORANGE and a double colored GREEN RED Green when GREEN LED is on USB connection is active Green GREEN LED on and RED blink USB connection active and programming activity erasing flashing programming unless TARGET is on Orange when ORANGE LED is off TARGET jumper is in position OFF Orange ORANGE LED on TARGET jumper is in position on BLINK means programming activity erasing flashing programming Page 15 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual CHAPTER 6 REVISION HISTORY AND SUPPORT 6 Introduction to the chapt
3. evaluation purposes only and is not considered by OLIMEX to be a finished end product fit for general consumer use Persons handling the product must have electronics training and observe good engineering practice standards As such the goods being provided are not intended to be complete in terms of required design marketing and or manufacturing related protective considerations including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards Olimex currently deals with a variety of customers for products and therefore our arrangement with the user is not exclusive Olimex assumes no liability for applications assistance customer product design software performance or infringement of patents or services described herein THERE IS NO WARRANTY FOR THE DESIGN MATERIALS AND THE COMPONENTS USED TO CREATE AVR ISP MK2 THEY ARE CONSIDERED SUITABLE ONLY FOR AVR ISP MK2 Page 2 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual The product is based on Dean Camera s LUFA USB stack More info at http www fourwalledcubicle com The LUFA library is currently released under the MIT license included below Copyright 2012 Dean Camera dean at fourwalledcubicle dot com Permission to use copy modify and distribute this software and its documentation for any purpose is hereby granted without fee provided that the above copyright notice appear in all copies an
4. VR ISP MK2 with Arduino AV RDude using the LibUSB drivers and changing the firmware BUT it is not possible at the moment to use the AVR ISP MKQ2 both at Arduino AVRDude and AVR Studio It would depend on you which one you prefer You need to change the firmware of AVR ISP MK2 using the Atmel Flip program AND the Windows drivers every time you switch between Arduino and AVR Studio or vice versa How to proceed changing the firmware All files needed except for Atmel Flip which is available at Atmel s web site for free should be downloaded from our web site and the AVR ISP MK2 page 1 Connect the device to the USB and with a needle or sharp object press the button on it s back side the one that the arrow points as Upgrade the LEDs should turn off which will put the processor in bootloader state ready for firmware upgrade 2 Download and install the Atmel Flip software Check in device manager if the device is recognized as AT90USB162 if it isn t search for proper drivers in Atmel Flip installation folder Page 9 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual pr 4M ee a 4 libusb win32 devices g ATIOUSB162 b S A Mice and other pointing devices b lls Monitors 3 After that run the Atmel Flip and select AT90USB162 in Device gt Select au Atmel Flip File Buffer Device Settings Help eS 466v V 9 Operations Flow r FLASH Buffer Information r ATSOLISB 162 Signature Bytes fee Z s si
5. arranty of Olimex products Warranty and returns Our boards have lifetime warranty against manufacturing defects and components During development work it is not unlikely that you can burn your programmer or development board This is normal we also do development work and we have damaged A LOT of programmers and boards during our daily job so we know how it works If our board programmer has worked fine then stopped please check if you didn t apply over voltage by mistake or shorted something in your target board where the programmer was connected etc Sometimes boards might get damaged by ESD shock voltage or if you spill coffee on them during your work when they are powered Please note that warrany do not cover problems caused by unproper use shorts over voltages ESD shock etc If the board has warranty label it should be not broken Broken labels void the warranty same applies for boards modified by the customer for instance soldering additional components or removing components such boards will be not be a subject of our warranty If you are positive that the problem is due to manufacturing defect or component you can return the board back to us for inspection When we receive the board we will check and if the problem is caused due to our fault and we will repair replace the faulty hardware free of charge otherwise we can quote price of the repair Note that all shippings back and forth have to be covered by the custo
6. d that both that the copyright notice and this permission notice and warranty disclaimer appear in supporting documentation and that the name of the author not be used in advertising or publicity pertaining to distribution of the software without specific written prior permission The author disclaim all warranties with regard to this software including all implied warranties of merchantability and fitness In no event shall the author be liable for any special indirect or consequential damages or any damages whatsoever resulting from loss of use data or profits whether in an action of contract negligence or other tortious action arising out of or in connection with the use or performance of this software Page 3 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual Table of Contents Page 4 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual CHAPTER 1 OVERVIEW 1 Introduction to the chapter Thank you for choosing the AVR ISP MK2 programmer from Olimex This document provides a user s guide for the Olimex AVR ISP MK2 programmer As an overview this chapter gives the scope of this document and lists the programmer s features The document s organization is then detailed 1 1 Features Tested and working with AVR Studio 4 AVR Studio 5 ATMEL Studio 6 Connects to PC via USB 2 0 Full speed Does not need external power supply as it takes the power supply from USB Uses Atmel s 2x5 pin ICSP and 2x3 pin PDI and TPI connector layout Wor
7. e target you might need https www olimex com dev avr icsp html since AVR ISP MK2 doesn t provide 6 pin ICSP connector Note it is bought separately Page 7 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual CHAPTER 3 AVR ISP MK2 BOARD DESCRIPTION 3 Introduction to the chapter Here you get acquainted with the main parts of the board Note the names used on the board differ from the names used to describe them For the actual names check the AVR ISP MKQ itself 3 1 Layout top view FIRMWARE UPGRADE BUTTON POWERING ICSP 10 pin OF TARGET JUMPERS Page 8 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual CHAPTER 4 RECOMMENDED SOFTWARE TOOLS 4 Introduction to the chapter Here you will find short info on the most popular choices for software that can be used with the AVR programmer 4 1 AVR STUDIO in Windows The most popular choice amongst AVR fans The IDE has everything you need for software development with AVR under Windows You can download it from the official Atmel web site AVR ISP MK2 comes with firmware for AVR STUDIO in order to use it with AVRDude or Arduino IDE which uses AVRDude follow the procedure in next chapter Note that separately you will have to download the AVRGCC compiler and install it 4 2 Arduino AVRDude Linux AVR ISP MK2 comes with firmware that supports AVR Studio In order to use AVR ISP MK2 with AVRDude GCC LibUSB Arduino you need to perform firmware change There is a way to use A
8. er In this chapter you will find the current and the previous version of the document you are reading Also the web page for your device is listed Be sure to check it after a purchase for the latest available updates and examples 6 1 Document revision Changes Modified Page E Initial Creation 11 07 12 Included LUFA license text B 23 07 12 C Added info how to update the firmware for 30 08 12 AVRdude Arduino IDE D Fixed a number of broken links and made a 13 14 17 21 01 13 couple of points clearer Page 16 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual 6 2 Useful web links and purchase codes The web page you can visit for more info on your device is https www olimex com dev avr isp mk2 html You can get the latest updates on the software at http www fourwalledcubicle com LUFA php ORDER CODES AVR ISP MK2 assembled and tested AVR ISP compatible programmer How to purchase Olimex products You can order from our web shop or from any of our distributors The list of official Olimex distributors might be found at https www olimex com Distributors Check https www olimex com for more info Page 17 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual 6 3 Product support For product support hardware information and error reports mail to support olimex com Note that we are primarily a hardware company and our software support is limited Please consider reading the paragraph below about the w
9. k adapters a1 Ports COM amp LPT 9 Communications Port COMI gt Di Processors gt amp Sound video and game controllers ql System devices p 9 Universal Serial Bus controllers Pon quee Uni Mus AVRISP mkll 2 s Waming You are about to uninstall this device from your system Page 11 of 18 OLIMEXO 2012 s Device Manager File Action View Help 9g I H ez 4 gy Lyubcho7 PC b 4M Computer p Disk drives A Display adapters gt fi DVD CD ROM drives gt eld Floppy disk drives b Floppy drive controllers b gg IDE ATA ATAPI controllers Junge o CEP WinDriver pcm Keyboards P FI Mice and other pointing devices p Monitors gt i Network adapters a YF Ports COM amp LPT LO Communications Port COMI J ECP Printer Port LPT1 D T Processors gt Q Sound video and game controllers p gill System devices p Universal Serial Bus controllers AVR ISP MK2 User s Manual wo AR S a Win Driver Waming You are about to uninstall this device from your system Delete the driver software for this device po ac no AL ILLO Lo S E E O M U M ee 9 Install the new drivers corresponding for your needs the picture below shows how to install the LibUSB drivers over the Jungo ones you have to browse to the LibUSB folder and install anyway riim 4 Device Manager File Action View Help lee
10. ks with 5V and 3 3V targets selectable and can supply target with power Programs both flash and EEPROM Supports fuses and lock bit programming Upgradeable for future device support Supports target voltages from 1 8V to 5 5V 2 ribbon female female cables 10pin and 6pin Adjustable ISP programming speed 50Hz to BMHz SCK frequency Dimensions 45x30 mm 1 7x1 2 20 cm 8 ribbon cable 9 9 9 9 9 9 9 9 9 o AVR ISP MK2 can program tinyAVR and megaAVR devices using the ISP Interface tinyAVR devices using the TPI interface and AVR XMEGA devices using the PDI Interface 1 2 Target market and purpose of the board AVR ISP MKQ2 is a ready to use programmer low cost clone of AVRISP MKII The board is suitabe for programming chips that according to their respective datasheets allow ICSP PDI or TPI programming modes OLIMEX AVR ISP MK2 is a programmer based on the hardware of AVRISP MKII clone open source project and the USB stack of the LUFA Lightweight USB Framework for AVRs project Page 5 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual started and maintained by Dean Camera More info about the initial idea and Dean Camera can be found here http www fourwalledcubicle com AV RISP php 1 3 Organization Each section in this document covers a separate topic organized as follow Chapter 1 is an overview of the board usage and features Chapter 2 provides a guide for quickly setting up the board Chapter 3 contai
11. l since AVR ISP MK2 doesn t provide 6 pin ICSP connector Note it is bought separately 5 1 2 6 pin PDI The 6 pin PDI is used for programming AVR XMEGA 5 1 3 6 pin TPI The interface used for programming tinyAVR 5 2 Upgrade firmware button There is a small hole between the PDI interface and the ICSP10 interface which nests a button below The button is used to reset the memory The memory can then be programmed with new firmware If you wish to update your firmware check if there is newer version in the web and follow the algorithm Page 13 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual 1 Connect the programmer to the USB and with a sharp object needle or pin press the upgrade pin it is in a small hole at the back of the board this will start the bootloader and will turn off the LED also probably will show a new unrecognized device in device manager for which we will install driver in step 3 2 Download and install the latest version of Atmel Flip software it can be downloaded from the Atmel s web site 3 Open its install folder and update the software of the unrecognized device usually under Other devices tab with the drivers from folder named usb the device should now be recognized as A T90USB162 under libusb win32 tab 4 Start Atmel FLIP and click Select a target device gt choose AT90USB162 5 Click Select a Communication Medium and then USB medium 6 From File gt load HEX file choose this HEX
12. mer Before you ship anything back you need to ask for RMA When you ship back please attach to it your shipping address phone e mail RMA and brief description of the problem All boards should be sent back in antistatic package and well packed to prevent damages during the transport Page 18 of 18
13. miEIBm sg S 4 g Lyubcho7 PC gt JE Computer aca Disk drives Display adapters gt A DVD CD ROM drives gt gel Floppy disk drives d Floppy drive controllers gg IDE ATA ATAPI controllers J Lu Junge 4M AVRISP mkII pm Keyboards i A Mice and other pointing devices A Monitors M Network adapters a1 Ports COM amp LPT n Processors i I Sound video and game controllers p gil System devices p F Universal Serial Bus controllers Update Driver Software AVRISP mkII Installing driver software Don t install this driver software You should check your manufacturer s website for updated driver software for your device Install this driver software anyway Only install driver software obtained from your manufacturer s website or disc Unsigned software from other sources may harm your computer or steal information vw See details Page 12 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual CHAPTER 5 INTERFACES AND HARDWARE 5 Introduction to the chapter In this chapter are presented the interfaces found on the programmed that can be found on the board Jumpers functions are described 5 1 Programming interfaces AVR ISP MKQ2 has three programming interfaces aiming at different processors 5 1 1 10 pin ICSP The ICSP in circuit serial programming interface is suitable for programming tinyAVR and megaAVR chips Depending on the target you might need https www olimex com dev avr icsp htm
14. ns the general board diagram and layout Chapter 4 mentions the main software tools used with AVR ISP MK2 Chapter 5 is an explanation of the interfaces the leds the jumpers position Chapter 6 contains the revision history useful links and support information Page 6 of 18 OLIMEXO 2012 AVR ISP MK2 User s Manual CHAPTER 2 SETTING UP THE AVR ISP MK2 BOARD 2 Introduction to the chapter This section helps you set up the AVR ISP MK2 development board for the first time Please consider first the electrostatic warning to avoid damaging the board then discover the hardware and software required to operate the board The procedure to power up the board is given and a description of the default board behavior is detailed 2 1 Electrostatic warning The AVR ISP MK2 comes in a plastic cover but make sure boards and devices interfacing with the programmer are properly grounded 2 3 Requirements In order to set up the AVR ISP MK2 optimally you might need to update your set of hardware and or software tools The major needed components are listed below Hardware tools USB A to USB B cable Atmel board or chip that can be programmed by AVR ISP MK2 The list of supported devices can be found in the official Atmel web site http www atmel com tools AVRISPMKII aspx tab devices Personal computer with USB port Software tools AVR STUDIO 4 5 or ATMEL STUDIO 6 with AVR GCC compiler AVR DUDE Depending on th
15. ze 12KB o a Oxo 0 RE Device Boot Ids L1 B Checksum xFF Blank Check Reset Before Loading Program HEX File AIMEL Select EEPROM 4 Slect Settings gt Communication gt USB gt Open Page 10 of 18 OLIMEXO 2012 File Buffer Device Help Operations Flow Erase Range 0x0 0x0 Checksum OxFF Blank Check Reset Before Loading Program Enter Demo Mode Ctrl D a XA Communication gt Preferences Ctrl P Enter Debug Mode Ctrl D RS232 Ctrl R n e CAN as dt USB Ctrl U LPC ll E Device Boot Ids 1 a Bootloader Ver Communication OFF AVR ISP MK2 User s Manual 5 From File gt Load hex files choose either AVR456 studio AVRISP MKII hex or libUSB AVRISP MKII hex the first hex is the firmware for AVR Atmel Studio the second one is for AVRdude Linux Arduino 6 Click Run 7 Unplug and plug again AVR ISP MK2 from the USB 0 Uninstall any previous drivers selecting delete option from device manager and scan for hardware changes or plug unplug again Am Device Manager File Action View Help 9 gn E Hl px iS e gE 4 y Lyubcho7 PC JE Computer xc Disk drives gt AK Display adapters 4 amp 3 DVD CD ROM drives gt ey Floppy disk drives ed Floppy drive controllers gt cg IDE ATA ATAPI controllers MY Jungo LEF AVRISP mkII i Pu WinDriver pcm Keyboards i n Mice and other pointing devices gt i Monitors amp Networ
Download Pdf Manuals
Related Search