Home

MPC-AWMVRL All-Weather LCD Displays User Manual

image

Contents

1. You shall soon become familiar with the quality difference in this bright sunlight readable 1nit to 1 000 nits Monitor specifically designed for use in harsh marine environments MarinePC has incorporated the latest LED backlighting to increase brightness and super low dimming without increased heat and extends temperature shock and vibration specifications The MPC AWMVRL handles a wide range of severe environments making it the first choice of serious mariners for their demanding applications Designed to be rugged the 800x600 SVGA native 15 is 1024x768 XGA High Resolution Flat Panel Display is engineered to thrive in the marine environment where you will put it to work Housed in a milled billet aluminum case the slim profile MPC AWMVRL is light weight and wa tertight with fully sealed IP67 case and connectors Engineered to be low power to conserve power the MPC AWMVRL has one RGB computer input and three Composite Video inputs with a source select button that lets you quickly move between inputs You may have purchased the MPC AWMVRL with the optional Analog Resistive Touch Screen within this User Manual are instructions for configuring this feature Also available is a pass through USB port Our MarinePC Service and Support Team is prepared to assist you we are MarinePC MPC AWMVRL UM B 1 2011 5 SAFETY General Safety Instructions Before operating the MPC AWMVRL Monitor read this User Manual thoroughly
2. Clock e Open the Clock function and e Press the UP or DOWN buttons to adjust clock horizontal stretch for the Display 22 MPC AWMVRL UM B 1 2011 OPTIONAL USB CONNECTOR Optional USB Connector The optional USB Connector is located on the rear panel pod It does not alter the water tight design of the monitor The unit remains sealed A dual USB cable is connected from the computer to the MPC AWM auxillary connector A 6 adapter cable is then connected to the MPC AWM to provide remote connection to any standard USB device such as a keyboard memory stick etc While the connection between the short adapter cable and the MPC AWM is waterproof the connection between the USB device and the short adapter cable is not water proof and should only be connected in dry conditions MPC AWMVRL UM B 4 2011 23 OPTIONAL TOUCH SCREEN MPC AWMVRX Optional Touch Screen Installation If you are installing a new operating system O S do not install the Touch Screen Controller Driver CD until you have installed the O S and verified the computer s CAUTION monitor display is working properly The Touch Screen Controller Driver uses the computer s O S display driver software settings to accurately configure the Touch Screen Controller Driver files Previous Versions of Touch Screen Controller Drivers Previous versions of ANY Touch Screen Controller Driver must be removed before installing the latest version of the TSHARC Touch
3. GF VMPC AWMVRL All Weather LCD Displays User Manual www MarinePC com Owner Record Here is an easy to locate form to record the unit s serial number and from the invoice record the invoice date The unit s serial number is located on the back panel If the unit ever requires service please refer to this information when contacting the MarinePC Service Center Product Serial Number Invoice Date MPC AWM__VRL www marinepc com Information Disclaimer This MarinePC User Manual is provided as is without warranty of any kind either expressed or implied including but not limited to the implied warranties or merchantability and fitness for a particular purpose Documentation Change Notice The information in this User Manual is subject to change without prior notice in order to improve readability and reliability as well as design and function These changes shall be incorporated in a new revision available from the product and or download section of the MarinePC web site www marinepc com Liability In no event shall MarinePC be liable for direct indirect special incidental or consequential damages arising out of the use of or the inability to use MarinePC s product or its documentation even if advised of the possibility of such damages Endorsement Product names mentioned herein are used for identification purposes only and may be trademarks and or regis tered trademarks of their respectiv
4. Note If the calibration target is not displayed under the finger select the Cancel button repeat Custom Calibration Settings a then Calibration Process 28 MPC AWMVRL UM B 1 2011 Calibration Drawing Test 1 Select the Test button on the Calibration tab 2 Using a finger or stylus draw or write and 3 Observe if the screen displays the drawing accu rately If it does not repeat the Custom Calibration Settings and Calibration Process instructions Click Settings Right Click 1 If desirable for Touch Screen application check the Enable Right Click box to set the right click option Right Click Area 2 Use the slide bar to set the Touch Screen event area to a size slightly larger than the activator larger for a finger tip smaller for a stylus the box displays the activator size Right Click Delay The timed hold right click mouse event allows the user to initiate a right click by holding down a touch point for a specific period of time 3 Use the slide bar to set the Right Click Delay value to the time necessary to produce a right click event Double Click Area This step sets the area that shall allow for a double click event Limit this to areas that can be accurately touched several times 4 Use the slide bar to set the double click area the box displays the activator size Double Click Speed 5 Use the slide bar to set sufficient time to perform a double touch in the specified area 6
5. Retain this User Manual for future use Verify the computer system capability see System Set up to insure operation of the Monitor For expeditious installation follow these User Manual instructions in the sequence presented Adhere to all Caution and Warnings on system parts and as stated in this User Manual All User Manual instructions for installation and operation must be followed precisely Adjust only those controls covered by the User Manual s operating instructions improper adjustment of other controls voids the unit s warranty and may result in unit damage and Adhere to local installation codes Safety Icons lt Warning Shock Hazards This icon is intended to tell you of a potential risk of electrical shock WARNING lt Caution Instructional CAUTION This icon is intended to tell you of important operating and or maintenance instructions General Unit Safety Always disconnect the unit from the power source before cleaning Do not operate the unit with a damaged cord Do not operate if the unit has been dropped or damaged The unit needs inspected by qualified MarinePC Service Personnel Position the power cord so it shall not be in contact with hot surfaces Do not allow anything to rest on the power cord and Do not place the power cord where there shall be foot traffic N General Safety Precautions WARNING Power cord must be connected to a properly wired and grounded power source Any equipment
6. 4 2011 15 7 Select the Monitor tab 8 Under Monitor Settings verify the Screen Refresh Rate is between 60 and 75Hz e If so select the Cancel button and go to step 9 e If not select a setting within the 60 75Hz range e Select the Apply button 9 At the Monitor Settings dialog box select Yes to accept the new desktop view settings 10 In the Display Properties dialog box verify the Screen Resolution is at 800 x 600 SVGA or 1024x768 XGA 11 Select the Apply button 16 MPC AWMVRL UM B 1 2011 Default Monitor and Intel R 82945G Express Chipset A x rettgAccelerator Driver Troubleshoot Color Management W General Adapter Monitor type Default Monitor Monitor settings Screen refresh rate Default Monitor and intel 29496 Express Chipset a x Color Management EE Intel R Graphics Media Accelerator Driver General Adapter Monitor Troubleshoot Monitor Settings Your desktop has been reconfigured De you wank to keep waa these settings Reverting in 12 seconds 72 Hentz Hide modes that this monitor cannot display lea ng this check box alows Vou i0 elect display nodes that this monitor cannot display corectly This may lead to an unusable display andor damaged hardware USER TIP Power on the Monitor e The Windows Operating System should automatically apply the best gen
7. Select the Finish button the TSHARC drivers shall be oe installed zj Inatructions congtePrst Frch to rl ouch nen diver Installation Complete 1 At the dialog box Setup is now complete TSE cae eu kee ion select OK exiting the TSHARC Touch Welcome coordinates when the screer s ae resized or rotated scopa pra al oun ean Be Screen Controller installation sp 2 Congratulations The MPC AWMVRX Touch Screen co SRRERRERERRSRRGRERRRR RRR fp it stalin Fished is ready to go to work Touch Screen Controller Setup Rey E xj 30 MPC AWMVRL UM B 1 2011 APPENDIX A Mechanical Drawings Mount diagrams of the MPC AWMVRxX and its dimensions may assist you in installation of the Monitor You may find them on our website at http www marinepc com products purchased model and size Mount diagrams of the optional Flush Mount Bezel and its dimensions may assist you in installation of the Monitor You may find them on our website at http www marinepc com products purchased size APPENDIX B Display Symptom No light behind button LEDs Possible Problem Solution No power loose power connection Confirm the Monitor is properly connected to a DC or AC power source Verify the power source is live or try another battery or AC power outlet Verify the Monitor is powered on Reverse Polarity Check polarity of the power connection Symptom Light behind button LEDs no display or No Signal error message and or no
8. installation A To ratal the Hampshire TSHARC controler diver chek Screen Controller Drivers Installation CD Accept HEULA Nest or press Ere a e Select Controller To ent Setup without installing the Hampshire TSHARC 5 Left mouse click to open ae contr diver cick Cancels anp tne 6 Left mouse double click to open the Resistive install ea ie Touch Driver file Bakuno tt progiem o ary poton a tae severe c cum per es Snc vai Prosec to the 7 Left mouse double click to open the file for a onlar ca radar Ia Ma ome 2000 XP 98 ME O S and ra or 8 Left mouse double click to run set up exe MPC AWMVRL UM B 1 2011 25 TSHARC Installation CAUTION If you need to cancel this driver installation at any time select the Cancel button on the driver installation dialog screen Software License Agreement HAMPSHIRE Press the PAGE DOWN key ta see the rect of the agreement Hamashire End User License Agreement HEULA PLEASE READ THE LICENSE AGREEMENT ln COMPANY END USER LICENSE AGREEMENT FOR HAMPSHIRE E TSHARC PRODUCT SOFTWARE Bm Accept HEULA solve are seiges above e computer software mei include associated mada Select Controller printed materiak and onkne o ekecvonis documentation SOFTWARE PRODUCT The SOFTWARE Configure PRODUCT also roides ary and supplements to Install the original SOFTWARE PRODUCT ace to pou bp Please read the following license agreement IMPORTANT READ CAREFULLY This
9. is not installed Uninstall the driver using TSUN10 exe If a correctly previous T S Controller Driver was installed all footprints must be removed Go to the T S manufacturer s web site or contact the manu facturer for instructions to uninstall drivers Reinstall the TSHARC Driver software MPC AWMVRL UM B 1 2011 33 APPENDIX C Technical Specifications 2 12M Colors 12M Colors 12M Colors TFT AM SVGA LCD 256K 1024 x 768 1024 x 768 1024 x 768 Colors 800 x 600 pixels pixels pixels pixels Sunlight Readable Dimming Ratio Video Input VGA 640x480 800x600 1024x768 P 1280x1024 1 100 nits LED Backlighting System IP67 Fischer High Density to DB 15 JAE to Flying leads DC Input Se nine teNte JAE to DB 9 Touch optional JAE to USB Port optional H r Milled Aluminum Black Anodized See UV Clear Coat Panel Mount or RAM Mount Power 6 Watts Min 13 Watts Max 15 Watts Max 17 Watts Max 35 Watts Max Consumption Wide Range g 39ypc DC Power Input 12 24 28 VDC nominal Internal Short Circuit Protection Power Load Dump Protection Conditioning Over Voltage Protection Reverse Polarity Protection 34 MPC AWMVRL UM B 1 2011 Environmental Specifications Operating Temperature Storage Temperature Ss AEA MPC AWMVRL UM B 1 2011 35 Warranty Terms and Conditions MarinePC offers it s products and services for sale under the following terms and con ditions Any and all
10. s rear panel pod These should be helpful when the installer cuts the required space for the Panel Mount installation Take care not to strip the screw holes or over tighten CAUTION as the enclosure is aluminum Flush Mount with Optional Bezel With the optional Flush Mount Bezel the MPC AWMVRL Flat Panel Display may be mounted flush with the mounting surface the ball and socket mount system will not be included in the shipping box For the mount diagram of the optional Flush Mount Bezel refer to the mount drawings on MarinePC s web site listed in Appendix A When the placement site has been decided it is recommended the installer use the measurements listed in the mount diagram of the optional Flush Mount Bezel when cutting the opening for the Monitor s installation Note the locations of the milled holes in the Flush Mount Bezel Drill corresponding holes into the substrate where the Monitor shall be mounted The installer shall need to supply screws for this type of installation Take care not to strip the screw holes or over tighten CAUTION as the enclosure is aluminum 12 MPC AWMVRL UM B 1 2011 CABLE CONNECTIONS Cables e The MPC AWMVRL is packaged with two cables Use care when inserting or VGA and DC Power removing connectors e The BNC cable s are provided by the end user and e The AC Power Adapter is optional Figure 7 CAUTION eoceecece ceo eee eee eee eee eee eee e 1 VGA Inpu
11. to which the unit shall be attached must also be connected to properly wired and grounded power sources Do not connect or disconnect the unit during an electrical storm Do not remove the unit covers there are no user serviceable parts in the unit Do not disassemble or modify the unit to avoid the possibility of electrical shock damage to electrical components or scratching the Display surface and Disassembly of the unit voids the warranty MPC AWMVRL UM B 1 2011 a Fluids from LCD Display CAUTION If the Monitor should ever become shattered do not touch fluids from an LCD Display If fluid should get on hands or clothing immediately wipe off with liquid soap or rubbing alcohol wash with water consult with a doctor and If fluid gets in the eyes flush eyes immediately with water for a minimum of 15 minutes consult with a doctor Electrical Connecting Cables e Disconnect the power to the computer when the Monitor is being installed and e Upon installation verify the power connector is securely seated on the unit Ratings and Grounding This unit may be operated from an 8 30 VDC power source external AC optional e Use the supplied power cable and e Always connect to a properly grounded power source Protection on Servicing Servicing User e User care is limited to cleaning the exterior of the unit e Do not disassemble or modify the unit or cables to avoid the possibility of an electrical shock damag
12. Hampshire End User License Agreemert HEULA is a legal Welcome aysen between you ether an individual of a ange ertly and Hampshire Inc for Ihe Hampshiis hich includes Kameshie Any sollvare provided along with the SOFT TWARE PRODUCT thot is associoted with a separate erduser license agreement is Scensed lo you under the terme of that license agreement By instaling copying desniading accessing or cthermise using the re F accept all of the tems of the above Licance Agreement Select Controller 1 The TSHARC Driver is a 12 bit controller the radio button is selected by default Note A PS 2 controller interface is not available 2 v Select the controller interface matching the cable used to install the MPC AWMVR Select the Autodetect button if installing the Touch Screen through a RS 232 serial interface There are two options for RS 232 installation Autodetect and Manual Manual instructions are found in section Manual RS 232 Controller Set up If connecting through a USB interface select the USB radio button Select Next Following installation select Finish and Reboot the computer when prompted Autodetect RS 232 Controller Set up 1 2 26 Select the Autodetect button The AutoDetect Serial dialog box lists the detected RS 232 controller information Select OK Installing Touch Screen Driver text box pops up indicating the progress of the installation Following installation sel
13. N buttons to set the Display s desired tint and e Ranges on the Display bar are low pinks mid range blues and upper greens Sharpness e Open the Sharpness function e Press the UP or DOWN buttons to select a desired sharpness for the Display and e Sharpness choices in the Display bar are preset at 0 33 66 and 100 Auto Color e Auto Color is best calibrated from an all white background From the VGA video source create an all white background e Open the Auto Color function e Press the SELECT button to run the Auto Color Setup Repeat twice and e When complete press the SELECT button to save the changes and exit 20 MPC AWMVRL UM B 1 2011 A check in a box indicates an enabled signal source attached to the Monitor Deselecting the box disables the Monitor s ability to display the signal Video 1 Composite e Open the Video function and e Press the UP or DOWN buttons to enable ON or disable OFF the Video 1 source Video 2 INACTIVE or if connected as above Video 3 INACTIVE or if connected as above PC VGA e Open the PC function and e Press the UP or DOWN buttons to enable ON or disable OFF the PC source OSD H Position e Open the OSD H Position function and e Press the UP or DOWN buttons to adjust the horizontal position for the OSD menu on the Display OSD V Position e Open the OSD V Position function and e Press the UP or DOWN butto
14. Screen Controller Driver CAUTION Uninstall TSHARC Utility Uninstall a Previous Version of TSHARC The uninstall utility TSUN10 exe is included on the TSHARC Touch Screen Con troller Installation CD in the shipping box with the product accessories This utility uninstalls TSHARC drivers only From the Product CD To uninstall install the CD gt go to My Computer desktop gt Left double mouse click gt Locate the drive with the Installation CD gt Left mouse click to open gt Left double mouse click on the Uninstall Drivers folder gt Left double mouse click on TSUN10 exe to execute the uninstall utility gt Follow the instructions Note The dialog box stating it is removing all Touch Screen Drivers from the computer means it is removing all TSHARC drivers Other Touch Screen Drivers must be uninstalled with their manufacturer s uninstall utility fs File Download From the Ma rinePC Web Site Do you want to open or save this file The TSHARC uninstall utility may be down x Name UniWinDriver 20cs zip Type WinZip File 972 KB load from www marinepc com Go to the Support tab gt Downloads gt Uninstall TSHARC Drivers gt TSUN10 exe Open f Uf cence Always ask before opening this type of file From www hampshirecompany com To download the utility left double mouse 7 While files from the Internet can be useful some files can potentially click on the file name gt At the File D
15. Select the Apply button to enter the selection and 7 Select the OK button to apply all Click Settings Hampshire TSHARC Control Panel Rey 6 20cs x Touch Settings Screen Selection Calbeation Click Settings Touch Settings Capactive 1 Normal Emulates a standard mouse allowing a single click double click drawing dragging and right click option if enabled 2 Touch Down Allows for a click event to take place at touch down No draw or drag is available 3 Touch Up Touch only Double click is disabled If right click was earlier enabled it shall be disabled featuses ae avaiable default ouch sent only at touch down All other features are valabla ouch sent only at TouchUp This desablles the nght ouse cick option Touch Sound 1 Check the Enable Touch Sound to enable a tonal beep when the screen is touched 2 Select the Apply button to enter the selection and 3 Select the OK button to apply all Touch Settings x C MPC AWMVRL UM B 1 2011 29 Capacitive Tab Disabled eae The Touch Screen is a resistive type the Capacitive Tab cemgte Ps Fen fale ach sereen Gier shall be disabled 7 s Weceme stress fate Tasnad Touch Screen Tray Icon TENEN on iain 1 If you do not want a Touch Screen Controller Icon to ae i one display in the toolbar tray go to step 3 or onzer 2 Ifyou want a Touch Screen Controller Icon to display bpe in the toolbar tray select the box and 3
16. a yous touch essen HAMPSHIRE roller is aap H 2 eae ee a a ce l MEENA COM Fot C COM 1 fdefaus C ca Welcome C coM2 git Accept HEULA C COM3 C co Select Controller Po coue ooo ene Baud Rate pAtvaccei Install C 2400 9500 deisi j z i012 BIT C ado 19200 me Seral CoM PETE SOEI 9600 bye Check the box if pou have a Capacitive Coriwolar im Capacitive Controller cox ie oos Hampshire TSHARC Control Panel Rev B2 F E zj HAMPSHIRE F Selection Infomation insbuctons 1 Select the mondo locala COMPANY e MPC AWMVRL UM B 1 2011 27 Ca i b ra t i O n Hampshire TSHARC Control Panel Rev 6 20cs xj Screan Selection Calbeation Chek Settings Touch Settings Capacitive The calibration process aligns the Touch Screen overlay to specific points on the Display screen Select the Calibration tab or in ten seconds the calibration program launches unless a Multi monitor situation is present then go to section Configuring a Multi monitor Installation There are three buttons Graphic Calibration and Test For default Four point calibration select the Graphic square This is the best known general calibration it compensates for skew and some edge linearity anomalies and 3 Go to section Calibration Process Custom Calibration Settings 1 To customize the calibration process select the Calibration button to bring up Calibration Optio
17. and 7 Reboot the computer when prompted TSHARC Calibration Program Upon reboot the Touch Screen is functional but not calibrated Calibration must be configured for the Touch Screen to work properly The TSHARC Control Panel initiates the calibration process e Go to Start gt Programs gt Hampshire TSHARC Control Panel The Control Panel has five tabs Each tab provides links to tools that can modify the TSHARC Drivers to meet specific needs e Touch Screen Display Selection e Calibration e Click Settings e Touch Settings e Capacitive Settings Note This feature is disabled MPC AWMVR is a Resistive Touch Screen TSHARC Control Panel Screen Selection Note If this is not a Multi monitor installation skip to section Calibration Configuring a Multi monitor Installation Note Microsoft does not support a Multi monitor installation in Win98 SE 1 The controller installation program opens to the Screen Selection tab Note the graphic representation of the Monitors installed on the system 2 Using the keypad or the mouse select the Monitor to calibrate 3 Switch to the Calibration tab Go to the next section Calibration 4 When complete return to the Screen Selection tab select the next Monitor Repeat the process until all Monitors are calibrated Sersan Selection Cation Cisk Seting Touch Seaing Capacitive Serial Configuration r Inetructions Salei tha ceamuricabn po th
18. e companies Copyright This document contains proprietary information protected by copyright All rights are reserved No part of this manual in whole or part may be reproduced by any means in any form without prior written permission of MarinePC MPC AWMVRL Professional Grade All Weather LCD Displays User Manual www MarinePC com Table of Contents Introduction cccccccccceccecccecceccesececcesecsccsecssesessecsecvsevsesesevsceeeeseee S en A EAA oe nae ee eee Product Care and Maintenance s un Systemi SEUD eiiean aora EEEa Instala tiO sussana an NEN Cable CONNECTIONS c cccccccesesesessesesssseseseeseescecevsenseveveee a Computer Hook up cccssscsssscssssssssssssssscsesessescescseseeseees aan Operator Controls gecesi tc sscsercacescissrocesysressaeaatteoseesemennienaenceen On Screen Display OSD ccsccsscssssssssscsssecssseessseeteseesees Optional USB Pass Through 2 cccccccsecceeseseeseeeeereeeeee E Optional Touch Screen Display 0 0 0 0 Appendix A Mechanical Drawings 0 0 6 _ Appendix B Troubleshooting ccceccceseeeseeeeeeeee er Appendix C Technical Environmental Specifications MPC AWMVRL UM B 1 2011 11 13 15 18 19 23 24 31 31 34 With this purchase of an All Weather Monitor MPC AWMVRL Professional Series we welcome you to MarinePC s family of ruggedized professional marine grade products
19. e to electrical components or scratching the Display surface and e Disassembly or modification voids the warranty Servicing MarinePC MarinePC Qualified Service Personnel may be required if the unit e Does not operate normally when installation instructions are followed e Does not operate normally when operating instructions are followed e Has been dropped or damaged or e Exhibits a distinct change in performance indicating a need for service Shipping If the unit should need to be shipped to the MarinePC Service Center the original packing material should be used to insure safety in shipping Repack the unit as it would have originally been received from MarinePC Radio Frequency Interterence CAUTION This equipment generates uses and can radiate radio frequency energy If not installed with the unit s accompanying cables it may cause harmful interference to radio communications MPC AWMVRL UM B 1 2011 7 PRODUCT CARE AND MAINTENANCE Product Care This MPC AWMVRL Monitor has been designed to provide optimum performance and service without any required scheduled maintenance other than occasional cleaning Turn off the Monitor power before cleaning the Monitor optional Touch Screen or unit s enclosure WARNING Do not use abrasive cleaners or solvent based flammable cleaners on the Flat Panel or Touch Screen Display its enclosure or any other electrical de CAUTION vice cables power cord etc Do n
20. ect Finish and Reboot the computer when prompted MPC AWMVRL UM B 1 2011 Select Controller HAMPSHIRE COMPANY Welcome Accept HEULA B Select Controller Configure Install 10 12 BIT Serial Instructions 1 At the Welcome screen select Next to go to the Software License Agreement EULA 2 After reading the EULA if in agreement check the box I accept all of the terms 3 Select Next Note Any unlawful use of the TSHARC driver is a strict violation of the United States and International copyright laws Using a TSHARC driver with any third party Touch Screen is strictly prohibited 1 Select the controller lype 2 Selci contol inlerface type Conticar Type 120110 Bt Controler Comtictier interlace Seal AS57232 ALlodalect C USB C P5 2 Jas Ea Select Controller Welcome Accept HEULA B Select Controller Configure r Instructions 1 Select Ihe controlar ypa 2 Select coriroller interface lyps t Controller Type 12o 10 Bi Cortrolles t Controller Irteslace USB Manual RS 232 Controller Set up 1 Select the Controller Interface RS 232 radio button 2 Select Next Note Do not select Autodetect 3 Follow the instructions entering the COM port selection 4 The Touch Screen Controller baud rate default is 9600 Note Capacitive Controller option is not available 5 Select Next 6 Following installation select Finish
21. eric driver for this connection and e Follow the instructions under section Computer Display Properties for optimum display quality MPC AWMVRL UM B 1 2011 17 OPERATOR CONTROLS On the right hand side of the Monitor bezel are seven Operator Control buttons Power On Off I O Button Power Button Note Monitor defaults to an AUTO OFF state when power is applied Brightness Control Toggle e The Power On Off button is marked with large sun small sun the I O Input Output symbol e Momentarily pressing this button shall _ turn ON or turn OFF the unit and Seem Select Button Blue LEDs glow behind the buttons when the unit is powered on Up Button Optional Feature Monitor defaults to an k AUTO ON state when power is applied This Down Arrow feature must be ordered when the Monitor is ordered It is not an add on after the unit is l Source Select Button built Brightness Toggle This toggle controls the brightness of the LCD Panel Display The large sun toggle side when repeatedly pressed or held down shall cause the Display s backlight brightness to increase e The small sun toggle side when repeatedly pressed or held down can be stepped down in increments to the lowest setting which is just above total black and suit able in very subdued light as in night time operations and e The Monitor shall revert to a mid range setting when the unit is powered off Adjust the brightness of the Display to
22. he main menu all changes are saved MPC AWMVRL UM B 4 2011 19 OSD Source Screen Menu Parameter Selections New settings shall be stored in memory upon pressing the SELECT button to exit the Source OSD Source Screen Category s Function Menu SAUNE If SELECT is not pressed or inactivity is detected within the 15 second factory default OSD duration any function adjustments made shall not be saved USER TIP Eeo ecco a sian nama Brightness Before adjusting the Brightness function parameters set the LCD panel backlight brightness using the control toggle large sun small sun set to its brightest large sun button in the ambient light source e Open the Brightness function e Press the UP or DOWN buttons to set the Display s desired brightness and e Adjustments go from very dim black to 100 very bright dazzling white Contrast Contrast is the difference in brightness between the light and dark areas of the pixels of a picture e Open the Contrast function e Press the UP or DOWN buttons to set the Display s desired contrast and e Predefined minimum to maximum is in the display bar Saturation Saturation is the vividness or intensity of the hue or color e Open the Saturation function and e Press the UP or DOWN buttons to set the Display s desired saturation Tint Tint is the pinks blues and greens of the Display e Open the Tint function e Press the UP or DOW
23. image on the display Possible Problem Solution Power on no video signal Verify the video cable is plugged into the VGA video connector Verify a video signal is coming out of the computer i e plug into a known good display source Verify the incoming signal source selected matches the Monitor signal source Composite S Video VGA Check the Brightness front panel setting on the Monitor This may be set too low Check the Brightness and Contrast controls in the OSD These may be set too low Computer may have gone into power manage ment stand by Press any key on the keyboard move the mouse or cursor or it there is the Touch Screen option touch the screen to wake up the computer MPC AWMVRL UM B 4 2011 31 Symptom Display has rolling bars across the screen or vertical shaded bars on the image Possible Problem Solution VGA video display is not set to view at 800 x Verify the computer video display settings of 600 pixels or 1024x768 pixels the signal are set to match the display and 60 75Hz refresh rate Defective video cable On a known good display source confirm the video cable is not defective Interference from adjacent equipment For proper grounding and shielding verify use of a proper video cable Keep the cable away from sources of EMI such as electric motors or unshielded RF sources such as radar and microwave Horizontal size is not adjusted In the OSD adjust the horizontal s
24. ize controls Symptom Picture quality image stability is distorted Possible Problem Solution Not working in 800 x 600 or 1024x768 pixel Press the arrow down button one time to auto resolution adjust the display Verify the video display settings match the monitor and 60 75Hz refresh rate Proper cable grounding and shielding Verify the use of a proper video cable with suitable grounding and shielding Keep the video cable away from sources of EMI and RF Improper video display settings Check signal source for proper signal Check for proper display properties selection of the display pixel setting Verify the display refresh rate 60 75Hz Display unit is farther than 3 m 10 ft from Single cable lengths in excess of the standard signal source 3 m 10 ft cable should be of high quality shielded VGA cable Contact MarinePC for information on custom cables Multiple Monitors are driven from the same Splitting the video signal divides the strength signal source of the signal A video signal booster line driver is recommended if installation requires more than one Monitor driven from a single video source Monitor has incorrect or bad sync signals Check for proper video cable installation or replace suspected faulty cable Check the video source is within the display s operating range max 1280x1024 pixels and 60 75Hz 32 MPC AWMVRL UM B 1 2011 Symptom Display image is not properly sized Po
25. llation TSHARC Touch Screen Controller Driver A TSHARC Touch Screen Controller Installation CD is included in the shipping box with the product accessories The driver is compatible with these O S Windows 98 SE Second Edition ME 2000 and XP Before loading Touch Screen Controller drivers verify the COM ports are enabled caution especially if using a laptop computer Installation 1 Attach the Touch Screen Cable connector to the MPC_AWMVRX 4 pin connector 2 Attach the Touch Screen Cable RS 232 connector to a computer serial port or 3 Attach the Touch Screen Cable USB connector to a computer USB port Note For Multi monitor applications all Touch Screens must be connected to the computer before installing the TSHARC driver If installing RS 232 connectors the driver has to be installed for each Touch Screen or CAUTION If installing USB connectors the driver is installed one time for multiple Touch Screens If the Touch Screen connector is USB Window shall load a temporary USB driver Wait for the driver to load 1 Boot up the computer 2 Insert the TSHARC Controller Driver CD 3 On the desktop left double mouse click on the My Computer icon Welcome to the TSHARC touch screen cortrole diner Setup The Setup progam for the Hampshire TSHARC controfers for Microsoft Windows Each Setup dalog has instructors for 4 Locate the drive with the TSHARC Touch Bp Welcome compiling a step ol the
26. ns and the Offset menu 2 Select OK when calibration and or offset selections are made _ e Three Point Calibration Quick calibration of a 3 Point 4 Point Calibration Calibration known good Touch Screen overlay No correc tion is applied z e Four Point Calibration Compensates for skew 7 Point 20 Point Calbration Calibration and some edge linearity anomalies e Seven Point Calibration More accurate than three point calibration No correction is applied e Twenty Point Calibration Provides the highest level of Touch Screen linearization and skew cor rection and e Offset Varied linearity exists between Touch Screen types user may want to calibrate the edges of the Touch Screen more precisely Default is 20 Calibration Process fa 1 Press the Center Graphic to start calibration EB 2 Targets are used to calibrate the Touch Screen Follow the on screen instructions Touch the target center es on Coltan Chen Senno Taush Sennan Capscaive hold until it shrinks then release the target and 3 Repeat the process for all targets Note the calibration screen shall time out and return to the Calibration tab if the first point is not touched within 10 seconds Calibration Verification Test 1 Touch the screen in several places to verify the calibration target is displayed under the finger and 2 Select the Accept button to apply and record the calibration data E
27. ns to adjust the vertical position for the OSD menu on the Display OSD Duration e Open the OSD Duration function and e Press the UP or DOWN buttons to adjust the time elapse between the last menu activity and when the menu disappears The range is between 0 and 100 seconds factory default is 15 seconds Ce ee ee AUTO Power e Select AUTO Power function if user wants system data channel signal source saved when the system is powered off Reset e Select Reset function and e Select YES to automatically adjust picture data to default such as brightness MPC AWMVRL UM B 1 2011 21 contrast saturation tint and sharpness System e Select System function to select the source signal type NTSC PAL and AUTO e Video 1 Composite NTSC e Video 2 Inactive e Video 3 Inactive e PC RGB and e AUTO Recommended selection Automatically assigns the correct video signal source association NOTE Source Screen Menu Category is enabled when the input signal is VGA H Position e Open the H Position function and e Press the UP or DOWN buttons to adjust the horizontal position of the screen display V Position e Open the V Position function and e Press the UP or DOWN buttons to adjust the vertical position for the screen display Phase e Open the Phase function and e Press the UP or DOWN buttons to adjust phase analog to digital for the screen display
28. onding functions menu with adjustable settings Picture Menu Source Menu OSD Menu Set up Menu Inactive OSD Tools Menu Parameter Adjustments e To choose a Display Parameter Category use the UP right or DOWN left buttons to move across the Source Screen Menu e As each Category icon is highlighted its related Functions Menu appears in a drop down box e To activate a Display Parameter Category move the highlight box over its icon and single press the SELECT button e Inthe Functions Menu a highlight bar is superimposed over the first function e Press the UP or DOWN buttons to move the highlight bar through the related Functions Menu e Single press the SELECT button to choose a Related Functions Menu item when it is highlighted e A smiley face appears to the left and a new color bar appears on the Function indicating the Category is active its parameters can be adjusted e The adjustment controls are the UP and DOWN buttons which increase or decrease the value of the parameter as noted in the percentage bar e Create the new parameter value e Single press the SELECT button to save the new value this returns the user to the Source Screen Menu e Exit from the Function Menu e To choose another Display Parameter Category use the UP right or DOWN left buttons to move across the Source Screen Menu and follow the above instructions or e Single press the SELECT button again to exit from the OSD Source Screen Menu or e Close t
29. or the ball mounting plate Take care not to strip the screw holes or over tighten Figure 4 e Line up one of the ball mounting plates on these three holes Figure 4 e With three 3 M4 x 10 counter sunk stainless screws attach this mounting plate to the back of the MPC AWMVRL e Mount the second ball mounting plate where the Monitor shall be installed e Insert each ball into the RAM arm e Lightly tighten the arm around the balls using the T knob on the arm Figure 2 4 e Adjust the Monitor to the viewing preference and e Tighten the T knob to hold the Monitor in position It is recommended the remaining ball be mounted on a flat surface Because of the various surface substrates the Monitor shall be mounted on the installer shall provide the screws to mount the other ball Panel Mount The Panel Mount installation should be specified at the time of order the ball and socket mount system will not be included in the shipping box The mounting hardware packet is included with the unit accessories in the shipping box This packet includes four 4 threaded screws approximately 7 6 cm 3 long four 4 Nylock nuts and four 4 flat washers For installation there are four tapped mounting holes on the four corners of the unit s rear panel The 15 contains 6 each It is recommended the installer refer to the mount drawings on MarinePC s web site with link address listed in Appendix A for the exact measurements of the unit
30. orders will be accepted only at the sole discretion of MarinePC and under these terms and conditions Any modification to these terms and conditions can only be made by MarinePC in writing Agreement to any modifications must be made by all participants of the sale prior to the acceptance of any order Prices All published prices are in effect from the date noted on the price sheet Prices are subject to change without no tice Written quotations may be requested Written quotations are valid for 30 days All prices are quoted in U S dollars Any and all taxes tariffs currency translations duties insurance freight charges and any other handling charges are the responsibil ity of the purchaser and must be prepaid and or charged Acceptance All orders will be accepted at the sole discretion of MarinePC Any order can be rejected for any reason at any time without liability Payment All purchasers must prepay the order accept COD shipment or arrange for other acceptable methods of guaranteed payment credit card cash prepayment etc before any order will be shipped VISA MasterCard DiscoverCard and American Express are welcomed and encouraged Shipments All shipments are FOB Scotts dale Arizona Purchaser is encouraged to provide MarinePC with shipping authoriza tion on their freight account Unless other wise specified MarinePC will select the best way for shipment using common carrier Fe dEx Ground or UPS G
31. ot use paper products as they may scratch the Display screen and Do not directly apply cleaning solutions to the Display screen Display Screen Cleaning e A vinegar based cleaner is preferred to prevent streaking and degradation of the coatings or e Anon abrasive glass cleaner such as a professional foam glass cleaner e Apply the cleaning solution to a soft clean cloth dampening slightly e Keep a fresh side of the cleaning cloth towards the screen surface to avoid scratching it with accumulated grit and To minimize the risk of abrasion to the screen air drying is recommended Disconnect cabling from the Touch Screen Display before cleaning A Touch Screen Display will be activated by cleaning the Display This may create a potentially WARNING dangerous condition Optional Touch Screen Cleaning e Follow cleaning directions above or use a special screen cleaning tissue or a solution specifi cally formulated for antistatic coatings e Lightly dampen a soft clean cloth with water vinegar based cleaner or a general purpose mild detergent solution e Keep a fresh side of the cleaning cloth towards the screen surface to avoid scratching it with accumulated grit and e To minimize the risk of abrasion to the screen air drying is recommended Monitor Enclosure e Clean the unit enclosure with a soft clean cloth lightly dampened with a general purpose mild detergent solution e Torinse wipe down with clean water and e Dry
32. own harm your computer If you do not trust the source do not open or save this file What s the risk load dialog box select Save gt Save the file to the computer s program files gt Make a new folder TSHARC Uninstall gt Select Open gt Save the TSUN10 exe file gt At the dialog box Download is complete select Open Folder gt Left double mouse click on TSUN10 exe to execute the utility gt At the dialog box Do you want to remove select Yes gt At the dialog box Press OK to complete the uninstall select OK gt At the uninstall confirmation screen select OK Follow the instructions Note The dialog box stating it is removing all Touch Screen Drivers from the computer means it is removing all TSHARC drivers Other Touch Screen Drivers must be uninstalled with their manufacturer s uninstall utility 24 MPC AWMVRL UM B 1 2011 Uninstall a Previous Version of Other Touch Screen Drivers If a version of a different Touch Screen Controller Driver not TSHARC is on the com puter it must be completely removed before installing the TSHARC Note The typical driver uninstall program or Microsoft s remove program utility does not remove all tracks of the Touch Screen Driver program Contact the manufacturer of the previ ously installed driver program to learn how to completely uninstall their product These instructions may be available from the manufacturer s web site Touch Screen Insta
33. r Display Properties XGA or SVGA Prior to connecting the MPC AWMVRX to the computer with another monitor verify the computer display properties are set to between 640x480 and 1280x1024 in 4 3 aspect ratio The optimum setting for viewing is 800 x 600 8 4 or 1024x768 pixels all other sizes The refresh rate must be set between 60 75Hz to eliminate screen flicker CAUTION Pixel settings different from the native resolution may exhibit less precise images and Pixel settings over 1280 x 1024 flash out of range with no display Setting the Display Settings Arrange Icons By Refresh 1 Right mouse click on an open area of the Paste desktop screen to bring up the Desktop Menu te Shortcut Undo Mowe Chrl z 2 Left mouse click on Properties to 7 the Display Properties menu Graphics Properties open ae Graphics Options New gt 3 Connect to a CRT monitor to establish the computer display properties Properties mn Display Properties Themes Deskiop Screen Sare Apes ance Settings 4 Select the Settings tab 5 Under Screen Resolution verify or slide the bar until the Screen Resolution is at 800 x 600 pixels SGVA or 1024x768 XGA Display 6 Select the Advanced button to Delat Honky an Intel B2443 Express Chipset Family go to the next menu to verify the Hz refresh rate Sereen rauli Coko qaau Less a Highest 32 be w 200 by G00 pral MPC AWMVRL UM B
34. round Shipments that are not FOB consignee or third party will incur a 20 handling charge and be added to the invoice Delivery is not guaranteed All risk of loss is assumed by the purchaser upon delivery by MarinePC to the carrier Special terms may apply for international shipments Unless otherwise specified by the purchaser and accepted by MarinePC at the time of purchase MarinePC reserves the right to partial ship any order Cancellations Once an order is placed by the purchaser and accepted by MarinePC cancellation charges will apply to any and all unshipped items Partial credit may be extended if products are returned unused in original packaging within 30 days of shipment No credit will be issued on any returns or cancellations after 30 days from date of shipment Returns Once a product has been shipped no returns will be accepted unless an RMA number has been issued by MarinePC prior to it s return The RMA number must be prominently displayed on the outside of the returned packing materials MarinePC cannot be responsible for damage from ship ping All authorized returns must be shipped prepaid directly back to MarinePC in the original packaging Returnee is responsible for all shipping and handling costs to and from the closest MarinePC authorized repair location For authorized in warranty service only MarinePC will pay for the return of the unit via normal domestic ground service Expedited return service or
35. shipment outside of U S must be prepaid by receiving party Standard Limited Warranty MarinePC war rants its products to be free from defects in materials for a period of Two 2 Years from the date of the original shipment from the factory MarinePC agrees to repair the product without labor cost to the purchaser for a period of One 1 Year from the original ship date No other warranty is expressed or implied Specifically excluded is normal wear and tear abuse or misuse of the prod ucts MarinePC does not make any claims or warrant the products with respect to the purchaser s use or application of the prod ucts Products returned but found not to be within the terms of this warranty are subject to a service fee to be paid prior to the return of the product to the purchaser Liability Any claim which may be made against MarinePC with regard to this con tract for sale must occur within One 1 year from date of original shipment from the factory INNO EVENT SHALL MarinePC BE LIABLE FOR LOSS OF PROFITS LOSS OF USE LEGAL OR PROFESSIONAL FEES CONSEQUENTIAL OR INCIDENTAL DAMAGE OR FOR SPECIFIC PERFORMANCE OF THE PRODUCTS THEIR MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PUR POSE UM AWMVRX A 1 2009
36. ssible Problem Solution OSD adjustments need to be made Adjust the vertical and horizontal size controls through the OSD Improper video display settings Check for proper display properties selection of the display settings Monitor autosize will only display full screen if source is 4 3 aspect ratio VGA signal source Auto Adjust needs The VGA source is able to auto adjust the activated Monitor to its optimum viewing setting Press the arrow down button one time to auto adjust the display Symptom Touch Screen T S does not respond Possible Problem Solution T S cable is not plugged in Verify the connections between the T S and the computer T S cable is installed in a different COM port Install the T S into another COM port If using than installed by the software a laptop verify the COM port s is enabled T S controller driver has not been installed Install the TSHARC controller driver Hardware failure Contact a MarinePC Technical Support Techni cian 480 515 1838 Symptom T S moves but does not follow a finger or stylus Possible Problem Solution Controller is not calibrated Run the calibration in the TSHARC Control Panel software T S Controller Driver is not installed Install the TSHARC Controller Driver T S cable is not installed correctly Verify the T S cable is installed correctly Symptom Error in Calibration message appears Possible Problem Solution The T S Controller Driver
37. t 2 DC Power Input 3 BNCInput Figure 6 Figure 7 Connectors Connectors are located on the bottom of the unit housing from left to right VGA Optional USB Pass through Optional Touch Power and 3 BNC Figure 8 Connectors are physically unique to insure the installer makes the proper connections eoceereecec eee eee eee eco eee eee eee eee eee VGA Input BNC Inputs 3 Optional USB Input Optional Touch Input Power Input eoeecerer ecco eee eee eee eee eee eee eee eee Figure 8 VGA Connector e The IP67 sealed VGA Cable 3 m 10 ft is in the accessory box e Line up the red dots on the connectors e Push the cable connector into the Monitor s back panel first connector 1 in Figure 8 and e Plug the standard DB 15 video female connector to the computer s video source secure MPC AWMVRL UM B 4 2011 13 DC Power Connector e The IP67 sealed DC Power Cable 3 m 10 ft is in the accessory box e Line up the red dots to 5 in Figure 8 e Plug in the quick connect three pin connector until it snaps e To disconnect pull the outside ring on the connector away from the unit until the cable is free DO NOT TWIST e There are two flying leads negative black and positive yellow labeled with e Connect the flying leads to the corresponding polarity on the DC voltage source Confirm the DC connections are made to CAUTION the correct polarity Composite BNC Connectors The MPC AWMVRL accepts a s
38. tandard NTSC or PAL composite video signal from any device typically a camera VCR or DVD This signal is carried to the Monitor via a coaxial video terminated with a BNC connector e The end user supplies the BNC coaxial video cable e The BNC receptacle on the Monitor is sealed e Line up with the last connectors 2 in Figure 8 and e Plug together adding a twist to lock the two pieces Optional AC Power Connector e The optional AC Power Adapter Cable Set consists of a 3 m 10 ft cable the power adapter and a 1 8 m 6 ft cable e The cable accepts voltage from 110 to 250 VAC and frequency from 47 to 63Hz e The AC power plug is standard for 120 VAC 60Hz common in North America and e Line up the red dots to 5 in Figure 8 e To disconnect pull the outside ring on the connector away from the unit until free Optional USB Pass through Connector e The optional USB Pass through Connector is an IP67 sealed four pin connector e The custom USB Cable is with shipping box accessories it is 6 m 2 ft e Line up the red dots to 3 in Figure 8 and e Plug together e To disconnect pull the outside ring on the connector away from the unit until free Optional Touch Screen Connector e The optional Touch Screen Connector is an IP67 sealed four pin connector e The connector is between the VGA and Power Connectors e Line up the red dots to 4 in Figure 8 and e Plug together 14 MPC AWMVRL UM B 1 2011 COMPUTER HOOK UP Compute
39. th custom foam packaging We recommend you save the box and all packaging materials in case the unit would need to be returned to the MarinePC Service Center Figure 1 In the shipping box you shall find e MPC AWMVRL unit e Power Cable e VGA Cable e Mounting System and Hardware e Touch Screen Cable if the optional Touch Screen is ordered and Touch Screen Driver Disk e USB Cable if the optional USB Pass through is ordered and e User Manual Figure 1 10 MPC AWMVRL UM B 1 2011 INSTALLATION The MPC AWMVRL is designed to be mounted with a universal ball and socket mounting kit ina Flat Panel or optional Flush Mount configuration Pedestal Mount The MPC AWMVRL is shipped with a RAM universal ball and socket system mounting kit Figure 2 By installing the Monitor with this kit the user can quickly adjust the viewing angle to improve viewability in changing environments This ball and socket system has proven to be successful in supporting an extreme amount of weight in high vibration and difficult mount applications See Appendix A for link to drawings Locate the ball and socket system in the shipping box The kit consists of two RAM balls on mounting plates and a RAM arm with an adjustable T knob and a packet of three 3 M4 x 10 counter sunk stainless screws for mounting to the MPC AWMVRL Figure 2 Figure 3 Figure 4 MPC AWMVRL UM B 4 2011 11 There are three mounting holes in the back of the Monitor f
40. the lowest possible setting for a given set of conditions and display characteristics Doing so shall provide the best viewing of the image extend the lamp life of the backlight and reduce the internal heat of the Display USER TIP Select Button The Select Button is the access point to the On Screen Display OSD Source Screen Menu See On Screen Display Up Button The Up Button is an adjustment tool in the OSD Source Screen Menu See OSD Screen Menu Parameters Down Button The Down Button is an adjustment tool in the OSD Source Screen Menu See OSD Screen Menu Parameters Source Button The Source Button allows the user to switch between video signal sources attached to the Moni tor Composite Video 1 2 amp 3 and VGA 18 MPC AWMVRL UM B 1 2011 ON SCREEN DISPLAY The On Screen Display OSD user interface is the path to all display signal source adjustments The Source Screen Menu with its user friendly graphical interface provides access to fine tuning the Display OSD Source Screen Menu Activation To activate the OSD menu in the current video source press and release the SELECT button Note OSD Source Screen Menu shall close after 15 seconds of inactivity This setting can be adjusted in the OSD Source Screen Menu OSD Menu icon under OSD Duration OSD Source Screen Menu Parameters The Source Screen Menu is comprised of six icons each representing distinct source screen categories and their corresp
41. with a soft clean cloth 8 MPC AWMVRL UM B 1 2011 To avoid risk of electrical shock do not disassemble the unit s enclosure Users cannot service the Monitor User maintenance is restricted to cleaning as ex WARNING plained Disassembling the unit voids the warranty Long term Storage For long term storage it is suggested the unit be stored in a normal indoor environment and the Display glass be protected from accidental damage For pedestal mount units disconnect the cable s and loosen the arm adjustment to a point where the ball can be removed from the arm or For Flush or Panel Mount units cover the product with a protective covering that shall not scratch or transfer any dyes to the Display screen Maintenance N Power Cord WARNING To avoid shock and fire hazards replaced the unit s power cord if e Insulation becomes damaged or e A loose connection is suspected Other Maintenance Only MarinePC Qualified Service Personnel shall perform all maintenance except for the power cord replacement described above MPC AWMVRL UM B 1 2011 9 SYSTEM SET UP System Requirements The computer the MPC AWMVRL shall be connected to must have this capability e Video card setting with a minimum resolution of 640 x 480 pixels and e Ifthe optional Touch Screen Display is ordered an available USB or COM port for the connector is required Shipping Box Contents The MPC AWMVRL is shipped in a custom box wi

Download Pdf Manuals

image

Related Search

Related Contents

Manual do Proprietário CBR1000RR Fire Blade  Samsung Blu-ray grotuvas H6500 Vartotojo vadovas  LG 15LW1R 15" LCD TV  N°3 : "Cartons" - Université Rennes 2  取扱説明書  《法人文書ファイル管理簿》  Manuel d`utilisation  UXT Series  

Copyright © All rights reserved.
Failed to retrieve file