PROFI GC - Comkit Online
Contents
1. Scroll set select 4 2 Operating states In the operating panel display the ON OFF switch shows the cur rent operating state through different colours The ON OFF button is colourless Machine is Off 12 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Controls Machine being prepared for operation The ON OFF button gradually goes green The wash tank is be ing filled and the machine is heating up Machine ready The ON OFF button illuminates completely green The machine is ready for the next wash cycle Wash program starts The ON OFF button illuminates completely blue Machine is washing The ON OFF button changes segment by segment from blue back to completely green Switch off machine The ON OFF button changes segment by segment from green to colourless The machine is being emptied and switched off 4 3 Display of faults and information Fault operation not possible The ON OFF button illuminates permanently red The fault is displayed For potential faults see section 9 7 Information limited operation is possible The ON OFF button illuminates green red alternately The information is displayed For potential information see section 9 7 4 4 Display function The display is activated when the machine is tur2. Hobart Norge Gamle Drammenvei 120 N 1363 H vik Tlf 47 67109800 E post post hobart no Hjemmeside www hobart no Hobart Scandinavia ApS H ndv rkerbyen 27 2670 Greve Danmark Tlf 45 4390 5012 Fax 45 4390 5002 E mail salg hobart dk Internet www hobart dk Hobart Sweden Finnland Tel 46 8 584 50 920 E mail info hobart se Internet www hobart se Australia Hobart Food Equipment Unit 1 2 Picken Street Silverwater NSW 2128 Tel 61 1800 462 278 Fax 61 02 9714 0222 E mail sales hobartfood com au Internet www hobartequipment com au HOBART China 15th Floor Building A New Caohejing International Business Center 391 Gui Ping Road Shanghai 200233 Telephone 86 0 21 34612000 Fax 86 0 21 34617166 Internet www hobartchina com 10 0000000121 001 EN 26 Jun 2013
3. 7 6 Washing Slide rack into the machine and close the door Push the ON OFF button 5 While the program is running the ON OFF button gradually changes from blue back to green gt As soon as the ON OFF button illuminates green again the wash cycle is finished gt Open the door and remove the rack gt Allow the washware enough time to dry 7 7 Switch off machine gt Close the door Push the ON OFF button for three seconds While the machine is draining the ON OFF button gradually changes from blue back to green During the drain cycle the machine interior is cleaned automatically Then remove any food debris v When the ON OFF button has gone out completely gt Turn off main switch or remove the plug gt Close site shut off valve 7 8 Executing daily cleaning NOTICE Property damage The use of unsuitable agents can cause corrosion damage gt Do not use any chloric acidic or metal containing additives to clean the machine gt Do not use metal brushes gt Open the door Remove strainer and clean Make sure that food debris does not enter pump intake HOBART 10 0000000121 001 EN 26 Jun 2013 27 EJ PROFI GC Operation Installation and Operation Instructions gt Flush the fine strainer under running water gt Clean machine interior gt Replace strainer gt Leave the door open for ventilation 7 9 Executing weekly cle
4. HOBART WAREWASHING Glasswashers PROFI GC GC 10A GCS 20A GC 90A Installation and EI Operation Instructions DSN GC 13 01 Start SN 86 61 03001 26 Jun 2013 EN PROFI GC Installation and Operation Instructions Publisher HOBART GmbH Robert Bosch Str 17 77656 Offenburg Tel 49 0 781 600 0 Fax 49 0 781 600 23 19 E mail info hobart de Internet www hobart de Product disclaimer Installations and repairs carried out by non authorized technicians or using non genuine spare parts and any tech nical alterations to the machine not approved by the manufacturer will invalidate the manufacturer s warranty and product liability HOBART reserves the right to make changes or improvements to its products without prior notice HOBART GmbH Offenburg 2013 2 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Table of Contents Table of Contents 1 Notes on the documentation aravvrarannrrnnnrrn nn rraren erare rraren rreren 5 1 1 Application sis04 404240 beds fake nran dav atadedidanactadebndatseade bets Frede E A 5 1 2 Layout of the documentation serrera Seed Ses abated ahi EANET ERE TEAKE knakk aan 5 1 3 Representation convention 0 a eee a e eden eee a 5 2 Safety instructions and regulations 0 6 c cece eect eee eens 7 2 1 Safety instructions and warning notices 0 tenet tenet teens 7 2 2 B sic safe
5. Fuse protection and cable cross section shall be executed ac cordingly gt The supply cord must be connected via a cut out device main switch or accessible plug device NOTE In accordance with EN 60 335 VDE 0700 the device must be connected to equipotential bonding The connection screw VY is located beside the cable inlet Connecting the water NOTE The machine must be operated with potable water To utilize the switchable cold rinse function GC 10A only con nect to cold water if possible max 20 C gt Connect to warm water if possible max 60 C Water hardness Machines without softener max 1 d 0 18 mmol l Machines with softener max 30 d 5 3 mmol l Line flow pressure Machines without softener 0 5 10 bar Machines with softener 0 8 10 bar If the line flow pressure is above 10 bar provide pressure re ducing valve gt Connect the union nut A 3 4 of the water supply hose to the site shut off valve gt Do not kink or cut the water supply hose gt Any required extension must be executed using a suitable pres sure hose e g 324088 1 18 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Installation Connecting the drain The connection between machine and site drain must not exceed max height of 0 6 m gt Do not kink or lay the drain hose loose on the ground pen ER
6. saved After the switch on times for each weekday have been entered the switch on must be set to active via the separate Activate deacti vate menu option When the time is reached the machine switches on Activate deactivate The Activate deactivate menu option offers the following four selection options Daily timer on Automatic switch on is activated for an entered day s date Weekly timer on Automatic switch on is activated for the saved weekdays and individual times HOBART 10 0000000121 001 EN 26 Jun 2013 37 EN PROFI GC Installation and Operation Instructions Setting options operating and hygiene data Daily and weekly timer on Automatic switch on is activated for an entered day s date and for the saved weekdays Timer off Automatic switch on is generally deactivated 38 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFIGC EJ Fault indications and problems 9 Fault indications and problems 9 1 Displayed error messages are shown in the order of priority They Fault indications must be acknowledged via the display navigation button Acknowledged error messages for which the error is still pending are first hidden to enable further messages to be displayed If all error messages have been acknowledged but errors are still pending these messages will then be shown again Information Limited operation is poss
7. 5 9 Retrofitting integrated chemical container optional Risk of electric shock Mounting the additional feed tanks touching live parts hot water tank heater tank heating pumps when working under voltage gt Have additional feed tanks mounted by qualified personnel gt For mounting see installation instruction for feed tank kit HOBART 10 0000000121 001 EN 26 Jun 2013 19 EJ PROFI GC Commissioning 6 Commissioning 6 1 6 2 6 3 6 4 6 5 Installation and Operation Instructions Personnel qualification Commissioning must only be carried out by qualified personnel see section 2 2 2 Starting the commissioning procedure When the machine is turned on for the first time the commission ing procedure starts automatically with the language selection followed by further requisite commissioning steps Push ON OFF button 4 Display is activated D Language menu is displayed Setting the language gt Push display navigation button amp or until the required lan guage is highlighted gt Push button 44 The language is activated Set day menu is displayed Setting the date gt Push display navigation button amp or until the required day is highlighted gt Confirm with button and skip to set month gt Repeat the procedure as described to enter month and year gt Push button L The date is activated L Set time menu is displayed
8. Date ing see sections 6 3to 6 5 Time Date format YYYY MM DD DD MM YYYY MM DD YYYY Time format 24h 12h Temperature unit C F Making the settings gt Open the operator menu see section 8 2 gt Open the General settings sub menu and make the setting see section 8 3 Setting the display indications The following settings can be entered into the Display indications sub menu Seiting Selection Program representation Text display Symbol display see section 4 6 7 Set brightness Display brightness Display contrast Set contrast Making the settings gt Open the operator menu see section 8 2 gt Open the Display indications sub menu and make the setting see section 8 3 Setting the acoustic signal An acoustic signal can be switched on or off in the Acoustic sig nal sub menu Selection Sound on sound off Setting Set signal sensor Making the settings gt Open the operator menu see section 8 2 gt Open the Acoustic signal sub menu and make the setting see section 8 3 HOBART 10 0000000121 001 EN 26 Jun 2013 33 EN PROFI GC Installation and Operation Instructions Setting options operating and hygiene data 8 8 Making the chemical settings The following settings can be entered into the Chemical settings sub menu Seiting Selection Detergent dosing Factory setting 2 5 g l Possible range
9. Observe the instructions on the packaging for storage lifting or transporting Avoid risk of explosion gt Do not install machine in a potentially explosive location Avoid electric shock gt Do not allow water to flow under live components Make sure the machine is correctly stored see frost damage section 2 3 Make sure that the machine does not overflow when being filled gt Do not damage the connection cable while unpacking 8 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Safety instructions and regulations Have the machine connected to the power supply by qualified personnel gt Have additional feed tanks mounted by qualified personnel Avoid fire risk gt Do not allow water to flow under live components Make sure the machine is correctly stored see frost damage section 2 3 Make sure that the machine does not overflow when being filled b gt Have the machine connected to the power supply by qualified personnel gt Have all modifications to the machine carried out by qualified personnel Avoid chemical burns sensitisation of the skin poisoning gt Wear protective equipment gloves safety goggles protective clothing when handling chemicals gt Use only suitable chemicals Observe the manufacturer s data gt Have chemical sensor system set by authorised trained service technicians gt Do not op
10. min 0 8 bar with integrated softener Cold or hot water connection max 60 C Voltage see rating plate Total connected load Fuse protection Tank capacity 8 Rack height 315 mm Noise emission workplace related emission 62 dB A for under counter machine value Weight 50 kg HOBART 10 0000000121 001 EN 26 Jun 2013 11 EJ PROFI GC Controls 4 Controls Installation and Operation Instructions 4 1 Controls 60s Short rN 90s Standard i 120s Intensive ON OFF button Pushing this button switches the machine on As soon as the machine is ready for operation the wash program can be started by pushing this button Pushing and holding 3 seconds this button activates the automatic drain and self cleaning cycle and switches off the machine automatically After switch off the machine is not voltage free The button also shows the current operating state through different colours see sections 4 2 and 4 3 STOP button In case of operating error or faults the machine can be switched off immedi ately without the drain cycle by pushing this button After switch off the machine is not voltage free Display Selection menu fault and information displays Display navigation button Scroll set select Display navigation button Change menu level confirm back acknowledge fault S e Display navigation button
11. serial number Operating data Displays operating data see section 8 77 Service Displays service address Overview of display symbols Wash cycle symbols As an alternative to the text display it is possible to switch to the symbol display see section 8 6 Symbol Program Short r Standard ar ar Intensive AT AT AT ar ar ar X Cold rinse GC 10A only ar Hygiene 14 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions 4 6 2 Function symbols PROFIGC E Controls Symbol Function K m Scroll menu Accept value amp Alter value Info Service Login back Temperatures gt 4 Wash rinse temperatures Sound on sound off Timer Salt deficiency Chemical deficiency Fault Fill fault Drain fault KE X Pb ES x Heating element fault HOBART 10 0000000121 001 EN 26 Jun 2013 15 EJ PROFI GC Installation 5 Installation HOBART 5 1 5 2 5 3 Installation and Operation Instructions Personnel qualification Installation must only be carried out by qualified personnel see section 2 2 2 Special safety instructions Risk of electric shock fire hazard Water frost damage machine overflow flowing over live compo nents can cause injury from electric shock or fire gt Do not allow wate
12. uaratereiraaisa doko seeeeeee htt aba b eens bees brekker akk de 17 9 9 Installing the Machine c 0 60 cca ie tee ad NEA na Pade Pada he cease teed dawedaGita coke gee 17 5 6 Connecting to the power supply n rsen ia a eee e eee ARNAN A 18 5 7 Connecting the water aurssassvass sekk kkaa ka aka Kabe ewe eee 18 5 8 Connecting the drain 2 eesti tE iniri pa Ka aa sa da seder seks ee eien 19 5 9 Retrofitting integrated chemical container optional 0 0 19 6 COMMISSIONING arsen Gee re kn 20 6 1 Personnel qualification si istkuaiesklaasosakasasede Paes Sad aa ha eke ye aea ae dae R AOR LG Gebal 20 6 2 Starting the commissioning procedure 0 cee eee ete teens 20 6 3 Setting the language sis onic sian agam n Tarkan heeded cane gee ae 20 6 4 SetiIng the Gale sa sa Gre goes dee boa dae AER 20 6 5 Seting the TIME oo 52 tad ed wine eevee eee hekk hd 225 VEE PDE eee bed ENANA NANKANA 20 6 6 Setting the water hardness optional 0 cece tenet enna 21 HOBART 10 0000000121 001 EN 26 Jun 2013 3 EN PROFI GC Installation and Operation Instructions Table of Contents 6 7 6 8 6 9 7 7 1 7 2 7 3 7 4 1 5 7 6 Lit 7 8 7 9 7 10 7 11 7 12 7 13 8 1 8 2 8 3 8 4 8 5 8 6 8 7 8 8 8 9 8 10 8 11 8 12 9 1 9 2 10 11 Filling the salt reservoir optional 0 00 cece eee nee 21 Filling the chemical container and chemical hoses 600s 22 Completing the commissioning p
13. until Login is highlighted gt Push button 4 Enter PIN is displayed Enter operator code 1111 gt Push display navigation button amp or until a 1 is shown in the first place gt Push button and skip to the next number gt Repeat the procedure as described until all numbers are en tered The operator menu is displayed once the correct code has been entered Navigating selecting and setting within the menu Navigating and opening sub menu gt Push or navigation button until the required sub menu ap pears and is highlighted gt Push button gt Menu is displayed Making and activating settings gt Push display navigation button amp or until the required setting is displayed and highlighted gt Push button 4 The setting is activated Back gt Push or navigation button until the Back menu option ap pears and is highlighted gt Push button 4 The next highest menu level is displayed Exiting the operator menu gt Open the door and close it again or do not press any button for 10 seconds Making the general settings The following settings can be entered into the General settings sub menu 32 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions 8 6 8 7 PROFI GC Setting options operating and hygiene data Seiting Selection Language is set as default during commission
14. 0 9 5 g Rinse aid dosing Factory setting 0 3 g l Possible range 0 2 0 g l Filling chemical hoses Fill detergent dosing hose NO YES Fill rinse aid dosing hose NO YES Making the settings gt Open the operator menu see section 8 2 gt Open the Chemical settings sub menu and make the setting see section 8 3 If in the Fill chemical hoses sub menu the prompt Fill detergent dosing hose and or Fill rinse aid dosing hose are set to Yes the filling process will start The filling process is visualised in the display by a time bar It can be stopped by pushing button if necessary 8 9 Configuring the counter for external water treatment optional The following settings for an optional external water treatment can be entered into the External water treatment sub menu Seiting Selection Set counter Set counter Factory setting not activated Reset counter Reset counter NO Reset counter YES Remaining water quantity Remaining capacity for external water treatment Displays the current demineralisa tion counter status water quantity remaining until the desalination cartridge is depleted Making the settings gt Open the operator menu see section 8 2 gt Open the External water treatment sub menu and make the setting see section 8 3 34 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Ey Setting options operatin
15. 01 EN 26 Jun 2013 25 EJ PROFI GC Installation and Operation Instructions Operation 7 5 Displaying and selecting the program 7 5 1 Overview of programs and additional functions Name Description Alternative symbol display Short For slight contamination pr Standard For normal contamination arn ar Intensive With increased rinse quantities OF AT AT Cold rinse for cooling glasses GC 10A only amamak Hygiene see also section 7 10 arm yg oe Basic clean Program for removing stubborn coatings de without posits on washware see section 7 11 Descaling See section 7 12 without 7 5 2 Displaying and selecting the program The machine runs automatically using the standard program If necessary a different program can be selected gt To display the current program before the start activate the in frared sensor in the display by hand or push the display naviga tion button 4 Display is activated gt Program selection and info menu is displayed 4 The program currently selected is highlighted gt To switch to a different program push amp or navigation button until the required program appears and is highlighted The selected program can be started directly via ON OFF button The machine continues with the chosen program until it is switched off 26 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Ey Operation
16. A3 HOBART 10 0000000121 001 EN 26 Jun 2013 43 EJ PROFI GC Disposal Installation and Operation Instructions 11 Disposal The machine operator is responsible for disposing of the machine and its operating materials correctly and in accordance with envi ronmental regulations Observe the national and local legal provi sions and regulations 44 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Ey HOBART 10 0000000121 001 EN 26 Jun 2013 45 46 HOBART GmbH Robert Bosch Str 17 77656 Offenburg Deutschland Tel 49 0 781 600 0 Fax 49 0 781 600 23 19 E Mail info hobart de Internet www hobart de Hobart UK Southgate Way Orton Southgate Peterborough PE2 6GN United Kingdom Tel 44 0 844 888 7777 Republic of Ireland 353 0 1246 0248 Fax 44 0 1733 361 347 E mail sales hobartuk com Internet www hobartuk com Compagnie HOBART SAS All e du fer mai 77183 Croissy Beaubourg FRANCE Tel 33 0 1 64 11 60 00 Fax 33 0 1 64 11 60 10 E mail contact hobart fr Internet www hobart fr Hobart Nederland BV Pompmolenlaan 12 3447 GK Woerden Telefoon 31 0 348 462626 Fax 31 0 348 430117 E mail info hobartnederland nl Internet www hobartnederland nl Hobart Foster Belgium bvba sprl Industriestraat 6 1910 Kampenhout Telefoon 32 0 16 60 60 40 Fax 32 0 16 60 59 88 E mail info hobart be Internet www hobart be
17. C for 24h Avoid water damage gt Configuration is password protected and only permitted by au thorised service technicians Observe documentation gt Do not operate the machine unsupervised Avoid environmental hazards gt Dispose of the machine correctly and in accordance with envi ronmental regulations see section 77 10 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Product description 3 Product description 3 1 Intended purpose The machine is an item of technical equipment intended solely for commercial dishwashing The machine is designed solely for cleaning crockery porcelain glass ceramic temperature resistant plastics up to 82 C stainless steel or similar from the food industry Not for washing Containers that do not come into contact with foodstuffs such as ashtrays candlesticks electric appliances etc Animals or textiles Foodstuffs intended for further consumption 3 2 Conformity See separate EC Conformity Declaration 3 3 Designation The rating plate is located at the rear of the machine and contains the following information model serial number date of manufac ture country of manufacture voltage connection rating design state number and CE mark 3 4 Technical specifications Dimensions H x W x D 700 x 460 x 590 mm Water consumption per rinse cycle 1 91 Line flow pressure 0 5 10 bar
18. Setting the time gt Push display navigation button amp or until the required hour is highlighted gt Confirm with button and skip to set minutes gt Push display navigation button amp or until the required minute is highlighted 20 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Commissioning Push button O L The time is activated 6 6 Setting the water hardness optional Machines with integrated softener have a water hardness setting Note The softener must be set to the existing water hardness ask at the local water works gt Push display navigation button amp or until the required hard ness is set gt Push button 4 Water hardness is activated 6 7 Filling the salt reservoir optional On machines with integrated softener an instruction to fill the salt reservoir appears during commissioning NOTICE Property damage Accidentally filling the salt reservoir with detergent will damage the water softener gt Do not fill the salt reservoir with detergent Unlike the regular salt fill additional water has to be added during the commissioning procedure gt Open the door gt Unscrew the salt reservoir lid and add 1 5 kg of granular 2 8 mm regenerating salt do not use salt tablets gt Fill up the reservoir with potable water only at commissioning gt Make sure the lid seal is free of dirt
19. a karat age eds oe de da Geld Sud etd wna boten TOAN AROEN EAER 32 Setting the display indications cossos ince ea seated a eee ee eee REEE eee EW ee ene 33 Setting the acoustic signal vuaks eee oa we ene Meee rrn rar ea ead be da hea duende edie dea ve dak va ve ee 33 Making the chemical settingS 0 c0cc cea ee ee en eee rA Ea aa 34 Configuring the counter for external water treatment optional 0 0 34 Setting the water hardness optional 0 cece eee teeta 35 Displaying the operating hygiene data 1 0 0 0 iii ec e eee 35 Setting automatic SWItCH ON wsccc008 vask svekka ee ea eee ee ee ee ee eee ae ee ee 37 Fault indications and problems 0 006 c cece eect eet nents 39 Fault indications ri rer kerk ee E eee ee eee oe EEEE EEEE EE eee ees 39 Remedying the problem ccc e0cceueteee cease verseaeav hed bbe EENAA EEVEE RTEA 41 Nene Ne 43 DISD OSSD EGEN EEE EEE 44 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Notes on the documentation 1 Notes on the documentation 1 1 Application This document contains the most important information for the installation and commissioning of the machine by qualified person nel as well as the information required for day to day operation by the operator gt Keep the operating instructions and all referenced documents in a safe and accessible place gt If you sell the machine pass on the
20. al HOBART glass racks HOBART racks hold the glasses in slightly inclined positions this improves the rinse efficiency To avoid unpleasant smelling glasses only chlorine free detergent 24 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Operation should be used for washing the glasses Before washing new glasses the first time with a commercial glass washer intensive basic cleaning is mandatory to reduce the greasy film which is on most glasses for protection during production We recommend this basic clean is carried out by hand wear gloves with a higher detergent concentration minimum 10 g l in a sink using a brush Alternatively the program described in section 7 11 can also be used 7 4 Preparations for washing 7 4 1 Preparing the machine gt Check correct position of wash rinse arms and strainers gt Open site shut off valve gt Turn on main switch or insert the plug gt Check level of detergent and rinse aid containers Close the door Push the ON OFF button L gt Machine is switched on L gt The tank is filled The ON OFF button will become gradually green during fill and heating cycle This process can take several minutes When the button becomes completely green the machine is ready for operation 7 4 2 Preparing the washware Remove any food debris gt Place washware face down in the rack HOBART 10 0000000121 0
21. and salt gt Screw lid back on and tighten HOBART 10 0000000121 001 EN 26 Jun 2013 21 EJ PROFI GC Commissioning 6 8 6 8 1 Installation and Operation Instructions NOTICE Property damage Salt residues on the tank bottom cause corrosion damage gt Remove salt residues by hand On completion of the commissioning procedure start rinse program to remove all traces of salt if necessary gt To continue the commissioning procedure press button Filling the chemical container and chemical hoses We recommend the use of HOBART Hyline detergent and rinse aid Chemical burns sensitisation of the skin poisoning The use of unsuitable chemicals can cause injury gt Use only commercial detergent and rinse aid gt Observe the manufacturer s application and safety instructions Chemical burns sensitisation of the skin poisoning Filling the chemical container or chemical hoses with detergent or rinse aid for the first time incorrectly can cause serious injury gt Wear protective equipment gloves safety goggles protective clothing when handling chemicals Provisioning external chemical canisters On machines without integrated chemical container an instruction to insert the suction hoses into the external canisters appears Preparing the detergent v Suction height of dosing pump max 1 5 m b gt Place suction hose without colour marking at the suction valve at th
22. aning gt Push and hold the clip fastener on the wash and rinse arms Remove the wash and rinse arms and clean gt Reinsert wash and rinse arms 7 10 Executing hygiene cleaning When a pre set number of rinse cycles has been reached the instruction Execute hygiene program appears in the display indicating that an automatic hygiene clean of the machine interior should be executed gt Before end of operation remove the rack and place 1 HOBART Hygiene Cleaner Tab in the machine interior gt Close the door gt Push or navigation button until the hygiene program ap pears and is highlighted Push the ON OFF button As the hygiene program runs duration approx 10 minutes the green illuminated segments extinguish successively At the end of the program the machine switches off automatically If necessary hygiene clean should be executed before the pre set number of rinse cycles is reached With regular use the machine interior will remain free of food debris and deposits 7 11 Executing the basic cleaning program for washware Special program for removing stubborn coatings deposits on wash ware e g protective film on new glasses starch residues 28 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Operation Chemical burns sensitisation of the skin poisoning The use of unsuitable chemicals can cause injury gt Manual addition of a dedicated agent as recommen
23. choose a stronger one Drain contaminated water and refill ma chine Clear washware more thoroughly beforehand Rack is not suitable for type of dishes sloping Use appropriate racks to create a sloping position which allows water to drain away from cavities Washware remains in the machine too long at the end of the cycle Remove washware as soon as program is completed to enable it to dry HOBART 10 0000000121 001 EN 26 Jun 2013 41 EJ PROFI GC Fault indications and problems Installation and Operation Instructions Nature of the problem Possible cause Remedy Streaks and stains on washware Rinse aid concentration too high stripe or bubble formation Reduce concentration see operating instructions Hard water or high mineral content Check water quality Every local water works holds data on the composition of the water they supply and will provide these on request Reference values Ideal hard water value 0 3 d total hardness Ideal mineral con tent value for glasses max conductivity 100 uS cm for dishes still viable to max 400 uS cm Rack is not suitable for type of dishes sloping Use appropriate racks to create a sloping position which allows water to drain away from cavities Inadequate rinse aid dosing causes stains Increase rinse aid dosing see operating instructions Machines with integrated softener
24. ctions All modifications and alterations to the product are reserved for persons authorised by HOBART Configuration is password pro tected 2 2 2 Personnel qualification gt Observe the regulations on occupational health and safety gt Carefully read through the operating instructions before use Activity User group Qualification training Installation Qualified personnel Authorised electricians qualified electricians or persons who have undergone equivalent training Trainees only under appropriate supervision and inspection Commissioning Qualified personnel Authorised electricians qualified electricians or persons who have undergone equivalent training Trainees only under appropriate supervision and inspection Working on the elec Qualified personnel Qualified electrician trical system Operation Laymen Training by the operator using the operating instructions hazard briefing Disabled persons Training by the operator using the operating instructions hazard briefing Children from 14 years Training by the operator using the operating instructions haz old ard briefing only under supervision Children up to 13 years not permitted old Maintenance repair Qualified personnel Hobart Service or Hobart trained service technicians Trainees only under appropriate supervision and inspection 2 2 3 Product specific hazards Avoid body parts being crushed or knocked gt
25. ded by your chemical supplier gt Observe the manufacturer s application and safety instructions gt Open the door Remove coarse soiling from tank strainer by hand v gt According to the manufacturer s dosing recommendations add the required powdered quantity for 8 litres of water to the flat side of the tank gt Activate the infrared sensor in the display by hand or push the display navigation button 4 Display is activated gt Program selection and info menu is displayed gt Push or navigation button until the basic cleaning program appears and is highlighted Slide the loaded rack into the machine and close the door Push the ON OFF button While the program is running duration approx 6 minutes the ON OFF button gradually changes from blue back to green As soon as the ON OFF button illuminates green again the rinse cycle is finished For each basic cleaning cycle that follows immediate ly an additional manual dosing is required for 4 litres of water 7 12 Executing the descaling program Program for de scaling the machine interior HOBART 10 0000000121 001 EN 26 Jun 2013 29 EJ PROFI GC Operation 7 13 Installation and Operation Instructions Chemical burns sensitisation of the skin poisoning The use of unsuitable chemicals can cause injury gt Manual addition of a dedicated agent as recommended by your chemical suppl
26. e bottom of the external reservoir Preparing the rinse aid v Suction height of dosing pump max 1 5 m gt Place suction hose with blue marking at the suction valve at the bottom of the external reservoir Filling the suction hoses gt Push button 22 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Ey Commissioning 4 The instruction Close the machine door is displayed gt Close the door and push button 4 Chemical hose filling is activated The filling process is visualised in the display by a time bar 6 8 2 Filling integrated chemical containers optional On machines with retrofitted integrated containers the instruction to fill the chemical containers appears gt Fill the colourless container with detergent to the MAX mark using a funnel Do not overfill the container gt Blue container fill the blue container with rinse aid to the MAX mark using a funnel Do not overfill the container gt Push button 4 The instruction Close the machine door is displayed gt Close the door and push button 4 Chemical hose filling is activated The filling process is visualised in the display by a time bar It can be stopped by pushing button if necessary 6 9 Completing the commissioning procedure The machine can be started or switched off selectively gt Push display navigation button amp or until the
27. egenerating salt see section 6 7 Faults Limited operation is not possible The ON OFF button illuminates permanently red The error code is shown in the display see table Once the error display has been acknowledged the machine switches off HOBART 10 0000000121 001 EN 26 Jun 2013 39 EJ PROFI GC Fault indications and problems Installation and Operation Instructions Error code Message text Measure 001 Hot water tank temperature sensor fault Con Contact your HOBART Service Partner tact service technician 002 Hot water tank temperature sensor fault Con Contact your HOBART Service Partner tact service technician 006 Wash tank temperature sensor fault Contact Contact your HOBART Service Partner service technician 007 Wash tank temperature sensor fault Contact Contact your HOBART Service Partner service technician 011 Wash chamber temperature sensor fault Con Contact your HOBART Service Partner tact service technician 012 Wash chamber temperature sensor fault Con Contact your HOBART Service Partner tact service technician 013 Disinfection not guaranteed Contact service Contact your HOBART Service Partner technician 014 Booster pressure sensor fault Contact service Contact your HOBART Service Partner technician 015 Booster pressure sensor fault Contact service C
28. en the door during operation wait for the program to finish gt Disconnect the machine from the mains prior to cleaning gt For cleaning wear protective equipment gloves safety gog gles protective clothing when touching parts contaminated by detergent Avoid burns scolds to the hands gt Do not open the door during operation or the evaporation phase wait for the program to finish gt Disconnect the machine from the mains prior to cleaning gt For cleaning wear protective equipment gloves safety gog gles protective clothing when touching parts contaminated by detergent Avoid slipping v Moisture can build up on the machine floor Provide a floor covering that is guaranteed to be non slip in case of moisture Residues on the washware hygiene regulations not main tained gt Hygiene regulations must be maintained and or demonstrated in accordance with the national provisions 2 2 4 Additional hazards Potential hazards caused by operating resources to be used can be found in the enclosed safety datasheets Workplaces must be HOBART 10 0000000121 001 EN 26 Jun 2013 9 EN PROFI GC Installation and Operation Instructions Safety instructions and regulations signed accordingly 2 3 Property damage Avoid frost damage v Temperatures below 0 C during transport storage cause func tion impairments gt Prior to installation store the machine at room temperature min 15
29. g and hygiene data 8 10 Setting the water hardness optional With optional softener only Note The softener must be set to the existing water hardness ask at the local water works The following settings can be entered into the Set water hardness sub menu Seiting Selection Water hardness setting is set as default during commission ing Factory setting 30 dH Possible range 0 30 dH Making the settings gt Open the operator menu see section 8 2 gt Open the Set water hardness sub menu and make the setting see setting 8 3 8 11 Displaying the operating hygiene data The following data can be called up from the Operating hygiene data sub menu Setting Selection Display operating data Commissioning date Operating hours until next service Operating hours overall Wash cycles overall Water consumption overall Operating days hours Daily wash cycles Daily water consumption Remaining capacity for external water treatment Hygiene data See section 8 11 1 Report See section 8 17 2 Display the setting gt Open the operator menu see section 8 2 gt Open the Operating hygiene data sub menu gt Open the corresponding sub menu and display the setting see section 8 3 HOBART 10 0000000121 001 EN 26 Jun 2013 35 EN PROFI GC Installation and Operation Instructions Setting options operating and hygiene data 8 11 1 Display hygiene data Hygiene re
30. ging materials and accessories from the ma chine gt Inspect the machine for possible transport damage 5 5 Installing the machine Risk of electric shock fire hazard Water ingress can cause short circuit and mortal danger from elec tric shock and fire gt Machine must be shimmed and be accessible only from the front gt Ifthe machine cannot be shimmed a rear cover must also be ordered Wall clearance is not required gt Align machine by turning the adjusting feet according to the spirit level gt Distribute machine weight equally onto all feet NOTICE Property damage Vapour may escape from the dishwasher door and damage the furniture gt Adjacent furniture has to be protected to prevent swelling HOBART 10 0000000121 001 EN 26 Jun 2013 17 EJ PROFI GC Installation 5 6 Installation and Operation Instructions Connecting to the power supply Risk of electric shock Failure to connect properly to the power supply can cause mortal danger from electric shock Have the machine connected to the power supply by an autho rized technician according to the local and national codes For Australia in accordance with AS NZS3500 1 The power supply must be consistent with the data on the rating plate Modification to an alternative power supply is possible as per the variants on the circuit diagram Connection diagrams are located adjacent to the connection terminals gt
31. ible The ON OFF button illuminates green red alternately The error code is shown in the display see table Error code Message text Measure 003 Temperature not reached Contact service Contact your HOBART Service Partner technician 004 Temperature not reached Contact service Contact your HOBART Service Partner technician 008 Temperature not reached Contact service Contact your HOBART Service Partner technician 009 Temperature not reached Contact service Contact your HOBART Service Partner technician 021 Fault in the drain system Clean the drain hose Clean the drain hose if necessary and pump if necessary and pump out the machine again out the machine again 022 Fault in the drain system Clean the drain hose Clean the drain hose if necessary if necessary 029 Program aborted Close the door Close the door 036 Detergent deficiency Refill detergent Refill detergent see section 6 8 037 Rinse aid deficiency Refill rinse aid Refill rinse aid see section 6 8 038 Input voltage too high Machine has been Have the input voltage checked by the site switched off electrician 039 Filling program aborted Close the door Close the door 041 External water treatment depleted Replace Replace part or full desalination cartridge 042 Osmosis pre filter depleted Replace Replace pre filter 043 Salt deficiency Refill regenerating salt Refill r
32. ier gt Observe the manufacturer s application and safety instructions gt Open the door v Remove coarse soiling from tank strainer by hand gt According to the manufacturer s dosing recommendations add the required de scaling agent for 8 litres of water to the flat side of the tank gt Activate the infrared sensor in the display by hand or push the display navigation button 4 Display is activated gt Program selection and info menu is displayed gt Push or navigation button until the de scaling program ap pears and is highlighted gt Close the door Push the ON OFF button As the hygiene program runs duration approx 10 minutes the green illuminated segments extinguish successively At the end of the program the machine switches off automatically Displaying the temperatures This menu option is for displaying the current tank and rinsing temperatures Procedure The machine must be switched on gt Activate the infrared sensor in the display by hand or push one of the display navigation buttons 4 Display is activated gt Program selection and info menu is displayed gt Push button 44 Login Temperatures Info menu is displayed gt Select the Temperatures menu option Current tank and rinsing temperatures are displayed 30 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Setting options operat
33. ing and hygiene data 8 Setting options operating and hygiene data 8 1 8 2 The machine can be operated as soon as the commissioning pro cedure is complete The following settings can be individually set as required using the operator menu Overview of operator menu Sub menu Function General settings Language Date Time Date format Time format Temperature unit Display indications Program representation Brightness Adjust contrast Acoustic signal On Off Chemical settings Detergent dosing Rinse aid dosing Filling chemical hoses External water treatment only when activated by HOBART Service Set counter Reset counter Remaining water quantity Hardness Setting Operating hygiene data Display operating data Display hygiene data Transmit report Timer Weekly program Timer program Activate deactivate Opening the operator menu v The machine must be switched on gt Activate the infrared sensor in the display by hand or push one of the display navigation buttons 4 Display is activated gt Program selection and info menu is displayed HOBART 10 0000000121 001 EN 26 Jun 2013 31 EJ PROFI GC Installation and Operation Instructions Setting options operating and hygiene data 8 3 8 4 8 5 gt Push button Login Temperatures Info menu is displayed Push display navigation button
34. installation and operating instructions 1 2 Layout of the documentation Referenced documents are all instructions that describe the instal lation operation maintenance and repair of the device as well as additional instructions for all accessories used For the operator Comic Card brief instructions Operating instructions For the specialised tradesman Installation instructions Service Manual Service Software Manual Trouble shooting list Circuit diagram Spare parts catalogue 1 3 Representation convention 1 3 1 Symbols used Symbol Meaning Warning of hazardous electrical voltage Beware of explosion HOBART 10 0000000121 001 EN 26 Jun 2013 5 EJ PROFI GC Notes on the documentation Installation and Operation Instructions Meaning Warning of risk of crushing Beware of hazardous substances Beware of hand injuries Beware of slipping Beware of hazard area Useful additional information and tips 1 3 2 Representation in the text Representa Meaning tion NOTE Important information on machine operation not a warning notice gt Step L Outcome result Listing 1st level Listing 2nd level 6 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Safety instructions and regulations 2 Safety instructions a
35. ions and problems 9 2 9 2 1 Poor wash result Remedying the problem Nature of the problem Possible cause Remedy Washware not clean Wash arms stiff you should be able to turn them easily by hand Remove wash arms and clean them thor oughly Also check water outlet from machine to wash arms is clear Wash arm nozzles are clogged visual check Remove wash arms remove cleaning caps and rinse wash arms thoroughly until all contamination is removed Replace cleaning caps Rinse nozzles clogged usually by lime deposit Remove rinse arms and de scale them in separate container Check site softener system for function Detergent concentration is too low or too high Check detergent concentration setting Coarse strainer clogged Remove empty and clean strainer Fine strainer clogged or obstructed by lime deposits Remove fine strainer If heavily soiled soak in a vinegar solution Then clean it thoroughly until the pores are free The fine strainer should generally be cleaned daily see operating instructions Wrong program selected for heavily soiled washware Select program with longer wash cycle Washware dries poorly Rinse aid dosing too low Increase dosing see operating instruc tions Washwere still greasy Detergent concentration too low increase see operating instructions Check if detergent is appropriate If not
36. levant events data and messages are listed in this menu option The list starts with the current date and the last event that occurred on this day The subsequent events occurring on this day then ap pear followed by the events occurring the day before The data of the last 30 days are saved Older lists are deleted Pushing button opens the list of completed wash programs The following data are saved Hygiene data Program temperature too low Thermal disinfection aborted Wash process aborted Messages Rinse aid empty Rinse aid deficiency remedied Detergent empty Detergent deficiency remedied Salt empty Salt deficiency remedied Service interval expired Half cartridge depleted Events Filling program Pump out program Washing program 8 11 2 Transmit report This menu option is for transmitting operating and hygiene relevant data in txt format to a USB stick This format can be imported and processed using standard software Procedure gt Open the door gt Remove sealing cover from USB port top right near door seal ing gt Insert USB stick into the port Select the Report menu option 4 After a successful download a message appears in the display Remove USB stick gt Close off USB port with the sealing cover 36 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Ey Setting options operating and hygiene data 8 12 Setting au
37. nd regulations 2 1 Safety instructions and warning notices gt During machine operation observe the general safety instruc tions and warning notices that precede each action 2 1 1 Hazard levels The hazard level is part of the safety instructions and is denoted by the signal word Potential consequences are differentiated by the choice of signal word imminent danger A DANGER results in serious physical injury or death potentially hazardous situation can cause serious physical injury or death potentially hazardous situation can cause minor physical injury potentially harmful situation NOTICE can cause damage to the product or other objects 2 1 2 Layout of warning notices Warning notices are depicted with warning symbols and signal word in the corresponding safety colours Nature and source of the hazard Explanation on the nature and source of the hazard gt Measures for averting the hazard gt additional measures for averting the hazard where applicable 2 2 Basic safety instructions 2 2 1 Product safety The machine conforms to state of the art technology and the rec ognised safety regulations Nonetheless hazards may occur Operate the machine only if it is in perfect working order and in HOBART 10 0000000121 001 EN 26 Jun 2013 7 EN PROFI GC Installation and Operation Instructions Safety instructions and regulations compliance with the operating instru
38. ned on by push ing the display navigation buttons or moving your hand near to the display On activation the wash program selection appears first The se lected program or function is highlighted The function of the display navigation buttons is context dependent and shown in the display by symbols Further displays menu levels can be selected using the button If no button is pushed the display de activates again after 10s HOBART 10 0000000121 001 EN 26 Jun 2013 13 EJ PROFI GC Controls 4 5 60s Short A 90s Standard i 120s Intensive login A Temperatures info maintena W general settin A display indica a acoustic signal machine type A operating data T maintenance 4 6 4 6 1 Installation and Operation Instructions Overview of main menus Program selection and info Selects possible wash programs depends on model variants The i button accesses the Login Temperatures Info menu Login Temperatures Info Login Operator code accesses Operator menu Temperatures Displays tank and rinse temperatures Info service Accesses the Info Service menu Operator menu Gen settings Accesses the machine settings Display indications Accesses display settings Acoustic signal Accesses the signal sensor setting see also section 8 1 Info Service Machine type Indicates machine type and
39. ontact your HOBART Service Partner technician 016 Wash tank pressure sensor fault Contact ser Contact your HOBART Service Partner vice technician 017 Tank pressure sensor fault Contact service Contact your HOBART Service Partner technician 018 Fault in the filling or drain system Contact ser Contact your HOBART Service Partner vice technician 019 Strainer blocked Remove clean and re insert Remove clean and re insert strainer 020 Wash tank pressure sensor fault Pump out Pump out machine machine 023 Fault in the filling system Supply quantity too Check site flow pressure low 031 Fault in the filling system Check water supply Check water supply 032 Fault in the filling system Check water supply Check water supply 033 Fault in the filling system Contact service tech Contact your HOBART Service Partner nician 035 Insert tank cover strainer correctly Insert tank cover strainer correctly 044 Salt deficiency Refill regenerating salt Refill regenerating salt see section 6 7 045 Number of wash cycles without regenerating Contact your HOBART Service Partner salt exceeded Contact service technician 052 Fault in the filling or drain system Contact ser Contact your HOBART Service Partner vice technician Disconnect machine from the water and power supply 40 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFIGC EJ Fault indicat
40. r to flow under live components gt Make sure the machine is correctly stored see frost damage section 2 3 gt Make sure that the machine does not overflow when being filled Risk of being crushed or knocked When being lifted or transported the machine can overturn or fall and cause injury gt Observe the instructions on the packaging for storage lifting or transporting Risk of explosion Installing the machine in a potentially explosive location can cause explosion and serious injury from ejected parts gt Do not install machine in a potentially explosive location Transporting to the installation location NOTICE Frost damage Temperatures below 0 C during transport storage cause function impairments Prior to installation store the machine at room temperature min 15 C for 24h gt Where possible transport packed on the pallet 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC ET Installation gt Use suitable transport means elevating truck crane etc gt If using a forklift shim the machine with wooden trusses 5 4 Removing the packaging Risk of electric shock fire hazard When the machine is unpacked the connection cable can become damaged and cause injury from electric shock or fire gt Do not damage the connection cable while unpacking the ma chine Take cable measurement BGV A3 Remove packa
41. required setting is highlighted gt Push button 4 The setting is activated HOBART 10 0000000121 001 EN 26 Jun 2013 23 EJ PROFI GC Operation 7 Operation 7 1 7 2 7 3 Installation and Operation Instructions Personnel qualification The machine must be operated by instructed personnel see sec tion 2 2 2 Special safety instructions Chemical burns sensitisation of the skin poisoning If the door is opened during operation washing water can spurt out and cause injury gt Do not open the door during operation wait for the program to finish Slipping Moisture can build up on the machine floor and cause slipping gt Provide a floor covering that is guaranteed to be non slip in case of moisture Notes for optimum washing result The wash result is significantly affected by the water quality If the mineral content is high the minerals dissolved become visible on the glasses in the form of spots and streaks during the drying process Authorised HOBART service personnel can determine i the content of minerals by measuring the electrical conductivity Values of less than 80 uS cm are non critical for washing glasses and cutlery If the values are higher we recommend the use of a HOBART HY DROLINE desalination cartridge or a reverse osmosis system If you have any questions please contact your authorised HO BART service partner We recommend the use of speci
42. rocedure 0 cece eect tet ann n nn n nn eee 23 Perl ico Fo 3 Seco caw eee a ee ce ee see 24 Personnel qualification s see sarndaana amai aaa ha a aa a abe ab e di nendeede de hogde daa i a a a 24 Special safety instructions sirsiran AEAEE dene eee E AERE 24 Notes for optimum washing results sisese aa i E LA A 24 Preparations for Washing o sss da eke ae een kake ee aod a dea de oe TEETE ee eee eee 25 Displaying and selecting the program 0 cc cee n eens 26 VWashing za arudnaadnovesdksvsvisrke Aaa ape ee O E E E EE EE EEE EEEE 27 SWICH Of MACHING spree ae serti nst E AAAA A E E ee sid de oa alae aes 27 Executing dally ClOAMING avant Farstad aa ade ade gar ah eee E dernest 27 Executing weekly Cleaning sasesana eee aed i eda dad bbe bE LER ak eka dies 28 Executing hygiene cleaning sss sassa ke kn ee eae ced ed hee begges reservedeler a 28 Executing the basic cleaning program for washware eens 28 Executing the descaling program 2 ici tcc ee eee eden 29 Displaying the temperatures 0 eens 30 Setting options operating and hygiene data 0 cece eee eee 31 Overview of operator MENU 2 ene eee e eee eeeee 31 Opening the operator menu 2 2 0 6 teen e tee te eee 31 Navigating selecting and setting within the menu 0 60 32 Exiting the operator menu ss ween ee we ea eee ee eee deeds beau ee oo ie dank eee ee 32 Making the general Settings Laxakanakaadaaa
43. tomatic switch on The Timer sub menu is for defining times for automatic machine switch on This can be done in two ways The Weekly program menu option can be used to define vari ous switch on times for individual weekdays The Daily Timer program can be used to define a non recur ring switch on time for today s date The switch on must be set to active via the separate Activate deactivate menu option The text frame shows the most recently selected of the four options When switch on is activated a small clock symbol remains in the top left hand section of the display for 30 minutes after the machine has been turned off Setting Selection Weekly program Weekdays and times Daily Timer program Date and time Activate deactivate Weekly timer ON Daily Timer program ON Weekly and Daily Timer program ON Timer OFF Making the settings gt Open the operator menu see section 8 2 gt Open the Timer sub menu and make the setting see section 8 3 Daily Timer program The date and time can be selected and altered using the display navigation buttons The switch on must also be set to active via the separate Activate deactivate menu option When the time and date are reached the machine switches on Weekly program Weekdays and an individual switch on time can be selected and altered using the display navigation buttons For weekdays on which no switch on is to occur no time may be
44. ty INSIFUCHONS surskskskak se ded cnn saa Daae Gates hens dpm enya dose seddedenat 7 2 3 Property damage sairia kaka ER daa Gara a ST VET ae de dod oldtid dok dekka 10 3 Product deSemPNoN La ccceginstarcsves sae Seradrn anes neneienesondses iden daw ebsesdaahee 11 3 1 Intended purpose saa gta kara de Alas waded seas ed eee bos 11 3 2 Conformity saa cte ee a kanna teas ken led rer ED ka aa Ged ew aia 11 3 3 De signati n rs rdssrtavrsgegandsaseseee sara bees LAL ee ae bee cas 11 3 4 Technical specifications aaavaaaaaa nn rann n nee nent near a aa 11 4 CONOIS oreen AE E da nededeunew ous rane dienes ceddesiseetebadasddccadats 12 4 1 CONolSuanuar sa SM eee Ted dd 12 4 2 Operating states aars oii baa Ae Sa KAREA ERASER A ila bibler die add JEG 12 4 3 Display of faults and information aaaauuaaannnnnrnnr rn ene nee eens 13 4 4 Display function NN a a G a aG E ESE E e eee eee eens 13 4 5 Overview Of MAIN Men s marssis sc niist Dran aA NER AAE EEE AAAS SENDA 14 4 6 Overview of display Symbols 2 ssasresserkarasskakkk seerne A AAA SEA 14 5 MEN ae a aANT E nes her Meee reer Te ery ee rere r sr rey er eer aes teenie 16 5 1 Personnel qualitication s vicevnddv ad veel baa kerk bia aes tivadeaedabaeed ed adeededad evaded ds 16 5 2 Special safety instructions vises sadn casa adun ada hete Fane anr eee eee a aa bede meme Meas 16 5 3 Transporting to the installation location 0 0 teen e eee 16 5 4 Removing the packaging
45. use of wrong Salt e g tablets Do not use salt tablets 9 2 2 Other problems Nature of the problem Potential causes Remedy Glasses are totally or partially cloudy Surface of glasses is rough and porous this is called glass corrosion Use new glasses this is not caused by a malfunction on the machine Glass dish breakage Use of unsuitable dish or glass racks Use suitable racks Machine switches off suddenly during opera tion Machine coupled to a maximum system or locked against other current consumers Have machine connected separately elec trician A site fuse has tripped Check site fuses 42 10 0000000121 001 EN 26 Jun 2013 HOBART Installation and Operation Instructions PROFI GC Ey Maintenance 10 Maintenance In order to maintain the warranty as well as a permanently safe efficient and trouble free operation of the machine s the required maintenance must be carried out by authorized service techni cians We therefore recommend the conclusion of an inspection and maintenance contract which guarantees qualified support by specially trained service technicians according to a time schedule based on the operating conditions In Germany your HOBART machines are governed by the Ordi nance on Industrial Health and Safety and must be inspected by a qualified electrician in accordance with the intervals specified in BGV
Download Pdf Manuals
Related Search