NWKSP2 - ComNet
Contents
1. comnet Communication Networks INSTALLATION AND OPERATION MANUAL uS netwave NWKSP2 COMNET SOLAR POWERED SYSTEM Thank you for purchasing NetWave from ComNet This manual will cover how to install hardware on your enclosure Configure batteries cabling and mounting of the enclosure The NetWave NWKSP2 Solar off the grid power system is designed for applications where a remote camera or wireless repeater is needed but power is not available or the cost to run power is too expensive NetWave Solar is a complete system tor providing remote power to edge communications equipment The kit includes high quality photovoltaic solar panels valve regulated lead acid battery outdoor enclosure solar charge controller PoE midspan injector and mounting hardware The steel outdoor enclosure has a gasket hinged lid with two tamper proot locks operated by a special key for high security The enclosure can be mounted on a two to four inch pole or wall mounted with the included mounting hardware The Solar Panels include a top of pole mount requiring a 4 diameter pole A side of pole mount is available as an optional accessory The included 30A solar charge controller supports an LCD screen for local diagnostics and system health monitoring Intelligent PWM charging mode and battery protection from overcharge and over discharge while the battery provides outstanding deep cycle and cold weather performance INSTALLATION AND OPERATION M2. 06810 USA T 203 796 5300 F 203 796 5303 TECH SUPPORT 1 888 678 9427 INFOGCOMNET NET CO ITI n et 8 TURNBERRY PARK ROAD GILDERSOME MORLEY LEEDS UK LS27 7LE Communication Networks 44 0 113 307 F 44 0 113 253 7462 INFO EUROPE COMNET NET 2014 Communications Networks Corporation All Rights Reserved ComNet and the ComNet Logo are registered trademarks of Communication Networks LLC TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 20
3. door backplate or sides of the enclosure DIN Rail installed on door TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 8 INSTALLATION AND OPERATION MANUAL NWKSP2 Attached the DIN Rail Adapters to the Controller and Power Injector then clip to the DIN Rail AL oy NOS 4 en joue 1940 AA Controller and Power Injector Mounted on DIN Rail Plug the external thermal sensor into the interface of the thermal sensor on the left of the controller S LARLAND HA 7 Thermal Sensor Plugged into Controller Insert battery platform in the enclosure The cutouts in the platform are for routing cable under the batteries Battery Platform on Floor of Enclosure TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE9 INSTALLATION AND OPERATION MANUAL NWKSP2 Pole Mount If mounting to a pole use the 6 included Stainless Hose clamps to secure the enclosure to a pole For your safety we highly recommend mounting the enclosure before installing the batteries Enclosure Mounted to Pole with Clamps Add the cable glands and drain plug to the bottom of the enclosure after mounting Battery Platform on Floor of Enclosure TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 10 INSTALLATION AND OPERATION MANUAL NWKSP2 Solar Panel Electrical Wiring Assemble The Solar Panels and run cable thru the cable glands on the bottom of the enclosure Do no
4. not more than that permitted for successful communication This device complies with Industry Canada license exempt RSS standards Operation is subject to the following two conditions e This device may not cause interference and e This device must accept any interference including interference that may cause undesired operation of the device Cet appareil num rique de la classe A est confrome la norme NMB 003 Canada Pour r duire le risque d interf rence aux autres utilisateurs le type d antenne et son gain doivent tre choisies de facon que la puissance isotrope rayonn e quivalente PIRE ne d passe pas ce qui est n cessaire pour une communication r ussie Cet appareil est conforme la norme RSS Industrie Canada exempts de licence norme s Son fonctionnement est soumis aux deux conditions suivantes 17 Compliance e Cetappareil ne peut pas provoquer d interf rences et TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 17 INSTALLATION AND OPERATION MANUAL NWKSP2 e Cet appareil doit accepter toute interf rence y compris les interf rences qui peuvent causer un mauvais fonctionnement du dispositif RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 2 52m from all persons and must not be located or operating in conjunction with any other antenna or transmitter Les antennes utilis es pour ce transmetteur doivent tre install en
5. ANUAL NWKSP2 About This Guide This guide is intended for different users such as engineers integrators developers and technicians It assumes that users have knowledge of the following Installation of electronic equipment Electrical regulations and guidelines Related Documentation The following documentation is also available Solar Charge Controller User Manual Solar Panel mounting instructions included with the mounting hardware Website For information on ComNet s entire product line please visit the ComNet website at http www comnet net Support For any questions or technical assistance please contact your sales person sales comnet net or the customer service support center techsupport comnet net Safety Only ComNet service personnel can service the equipment Please contact ComNet Technical Support The equipment should be installed in locations with controlled access or other means of security and controlled by persons of authority Do not install equipment on wet or windy days Make sure you have assistance mounting the hardware Complete as much of the setup as you can on the ground in a safe environment TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE2 INSTALLATION AND OPERATION MANUAL NWKSP2 Contents About This Guide 2 Related Documentation 2 Website 2 Support 2 Safety 2 Overview 4 Legal Information 4 Introduction 5 Pole Mounting Bracket Assem
6. al service or the shop where you purchased the product TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 18 INSTALLATION AND OPERATION MANUAL NWKSP2 GPL General Public License Statement You may have received from ComNet products that contained in part free software software licensed in a way that ensures your freedom to run copy distribute study change and improve the software Such products include NetWave series of products As part of these products ComNet may have distributed to you hardware and or software that contained a version of free software programs developed by the Free Software Foundation a separate not for profit organization without any affiliation to ComNet See http www gnu org philosophy free sw html for more details If ComNet distributed any portions of these free software programs to you you were granted a license to that software under the terms of either the GNU General Public License or GNU Lesser General Public License License copies of which are available from http www gnu org licenses licenses html The Licenses allow you to freely copy modify and redistribute that software without any other statement or documentation from us ComNet will provide to anyone who contacts us at the contact provided below for a charge of no more than our cost of physically performing source code distribution a complete machine readable copy of the complete corresponding source code for the free softw
7. ardware TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 16 INSTALLATION AND OPERATION MANUAL NWKSP2 Agency Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference and e This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a Industrial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Industry Canada This Class A digital apparatus complies with Canadian ICES 003 To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is
8. are programs used in the version of the programs that we distribute to you The cost will be free if the delivery medium of the machine readable copy is through the Internet Contact information Email techsupport comnet net Tel 203 796 5300 Address 3 Corporate Drive Danbury CT 06810 USA We will reply within 7 working days once the request has been made through email or telephone TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 19 INSTALLATION AND OPERATION MANUAL NWKSP2 ComNet Customer Service Customer Care is ComNet Technology s global service center where our professional staff is ready to answer your questions at any time Email ComNet Global Service Center customercare comnet net Contact Information ComNet www comnet net Mo emu e ce MP MM UI a Tel 1 888 6789427 Email info comnet net E alg A EE A E ComNet Europe Ltd Leeds Tel 44 0 113 307 6409 Email info europeQcomnet net 6 0 6 6 06 9 9 0 0 6 0 0 0 9 0 0 0 0 0 9 9 06 0 0 GO 0 0 9 0 0 eee eee 0 9 0 O 9 0 0 O 9 0 0 9 0 O 9 0 GO 9 0 0 O 9 0 O 0 0 O 0 9 0 O 9 0 0 O 9 0 O 9 0 O 9 0 0 O 9 0 O0 0 0 O 9 0 O 9 0 0 O 9 0 0 0 0 O 9 0 O O 9 0 0 O 9 0 0 GO 9 0 0 O GO 09 0 O 9 0 0 9 6 O 0 0 O0 O 9 0 0 GO 9 0 0 O 0 0 0 O 0 9 0 9 0 O 9 0 0 O 9 9 0 0 9 9 0 0 0 9 6 6 9 ComNet Corporate Headquarters and Customer Support Center EMEA PACRIM South America 3 CORPORATE DRIVE DANBURY CT
9. bly 6 Preparing the Enclosure 8 Pole Mount 10 Solar Panel Electrical Wiring 11 Battery Installation 12 Agency Compliance 15 GPL General Public License Statement 17 TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE3 INSTALLATION AND OPERATION MANUAL NWKSP2 Overview Legal Information No part of this document may be reproduced or transmitted in any form or by any means electronic and mechanical for any purpose without the express written permission of ComNet Copyright Copyright O 2014 ComNet All rights reserved Disclaimer ComNet reserves the right to make changes in specifications at any time without notice The information furnished by ComNet in this material is believed to be accurate and reliable However ComNet assumes no responsibility for its use TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 4 INSTALLATION AND OPERATION MANUAL NWKSP2 Introduction The NetWave NWKSP2 Solar off the grid power system is designed for applications where a remote camera or wireless repeater is needed but power is not available or the cost to run power is too expensive NetWave Solar is a complete system for providing remote power to edge communications equipment The kit includes high quality photovoltaic solar panels valve regulated lead acid battery outdoor enclosure solar charge controller PoE midspan injector and mounting hardware The steel outdoor enclosure has a gasket hinged lid with two tamper proof l
10. consid rant une distance de s paration de toute personnes d au moins 2 52m et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it This equipment may be operated in the following countries Great Britain and Northern Ireland Austria Belgium Denmark Finland France Germany Ireland Italy Netherlands Norway Portugal Romania Switzerland Sweden Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer s responsibility to make sure the device is operated within local country regulatory requirements RoHS WEEE Compliance Statement European Directive 2002 96 EC requires that the equipment bearing this symbol on the product and or its packaging must not be disposed of with unsorted municipal waste The symbol indicates that this product should be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities waste dispos
11. ocks operated by a special key for high security The enclosure can be mounted on a two to four inch pole or wall mounted with the included mounting hardware The Solar Panels include a top of pole mount requiring a 4 diameter pole A side of pole mount is available as an optional accessory The included 30A solar charge controller supports an LCD screen for local diagnostics and system health monitoring Intelligent PWM charging mode and battery protection from overcharge and over discharge while the battery provides outstanding deep cycle and cold weather performance This manual contains detailed operational and configuration information TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE5 INSTALLATION AND OPERATION MANUAL NWKSP2 Pole Mounting Bracket Assembly If mounting the enclosure to a wall you can skip this step and mount the enclosure directly to a wall using the 4 holes in the back of the enclosure Mounting Hardware TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 6 INSTALLATION AND OPERATION MANUAL NWKSP2 TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE7 INSTALLATION AND OPERATION MANUAL NWKSP2 Preparing the Enclosure Attach grounding wire to the door and enclosure Remove plastic covers on copper studs Add grounding cable to the two studs and use the copper washers and nuts to secure Grounding Cable Installed Mount the DIN Rail The DIN Rail can be mounted to the
12. posts PV Cable Connecting Battery Terminals NOTE Please apply rubber insulator to the terminals to prevent contact with the door in case of earthquake or vibration TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 13 INSTALLATION AND OPERATION MANUAL NWKSP2 Rubber Insulator Connect the Positive and Negative cables from the battery to the Controller battery terminals m S LARLAND m A vo Battery Cables Connected to Controller Battery Terminals Once batteries are connected to the controller connect the PV cables from the solar panels to the Solar Load terminals on the controller S LARLAND A vo Solar Panel Cables Connected to Solar Load Terminals on Controller Connect the 12 Bonded Red and Black cable to the green terminal adaptor then connect the other end of the cable to the load terminals on the controller TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 14 INSTALLATION AND OPERATION MANUAL NWKSP2 Red and Black Cable Connected Green Terminal Connector left and to Load Terminals on Controller right TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 15 INSTALLATION AND OPERATION MANUAL NWKSP2 Insert green terminal into the Power Injector Green Terminal Connector attached to Power Injector See Solar Charge Controller User Manual for instructions on how to use the controller Solar Panel mounting instructions will be included with the mounting h
13. t connect PV cables to the controller yet it is recommended to connect the battery first Enclosure Mounted to Pole with Clamps The NWKSP2 Kit Panels will need to be configured in parallel using the MMF MaleMale to Female and FFM FemaleFemale to Male Connectors Connect the MCA Male Positive Connectors from the solar panels to the MMF Connector then connect the 15 Cable with MC4 Female Connector to the Male FFM Connector and run cable thru a cable gland of the enclosure Connect the MC4 Female Negative Connectors from the solar panels to the FFM Connector then connect the 15 Cable with MC4 Male Connector to the Female MMF Connector and run cable thru a cable gland on the enclosure Note The cables may ship as one 30 cable If this is the case you will need to cut the cable in half creating two 15 cables Please reapply the Twist Nut to the open end of the cables to prevent a short 15 Male and Female Cables TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 11 INSTALLATION AND OPERATION MANUAL NWKSP2 TECH SUPPORT 1 888 678 9427 INS NWKSP2 REV 07 10 14 PAGE 12 INSTALLATION AND OPERATION MANUAL NWKSP2 Battery Installation Insert battery into the enclosure The battery can be installed vertically or horizontally We recommend installing on its side for ease of access Enclosure Mounted to Pole with Clamps Connect the 24 10AWG cables to the positive and negative battery
Download Pdf Manuals
Related Search