Home
EZ-PROX
Contents
1. z oo0od A O NA Timer NO E lock DC out Push button GND PB O a 0 20 secs Yale Release RED BLACK PINK WHITE 240vAC INPUT Exit Button O How to enter programing mode Input the admin default code twice 1234 and1234 but a If the admin code is 2 digit please input 12 and 12 b If the admin code is 3 digit please input 123 and 123 c If the admin code is 5 digit please input 12345 and 12345 The rest may be deduced by analogy The admin code is max 6 digit 123456 After enter the admin code the yellow LED will be on Factory default admin code is 1234 Programming a fob or card Enter any 3 digit number from 000 to 999 yellow light blinks 1 If red LED indicator is on it means there is data stored in this position then press twice to delete the information in this position 2 If green LED indicator is on it means card or fob can be added in this position Add card steps 1 Enter in setting mode and the yellow light blinks 2 Input 3 digits number from 000 to 999 to choose a position 3 When the green light is on swipe card Bleep sounds means add card successfully Press to exit the setting mode Deleteing a fob or card Enter any 3 digit number from 000 to 999 yellow light blinks Red LED indicator is on means
2. Green light stops blinks indicates new master card or fob is added successfully Press to exit the setting mode Use the master card or fob to enter the setting mode Swipe the master card or fob Yellow light is on with Bleep sound means it enters the setting mode Swipe the master card or fob again The Bleep Bleep Bleep sound means it exits the setting mode The blue light is on Delete all user fobs and cards and restore to factory default In the setting mode Press 8 yellow light blinks then press 8 twice Bleep Bleep Sounds yellow light stops blinking It indicates all user cards or fobs have been deleted successfully All the card or fob settings are invalid Press 8 yellow light blinks then press 9 twice yellow light is on and Bleep sounds Restore to factory default setting successfully All the settings are in default status Press to exit the setting mode If enter wrong information Bleep Bleep will be heard The setting mode will exit automatically if no actions in 30 seconds accompanied with Bleep Bleep sound If it is not in the setting mode and the action of pressing numbers is uncompleted it will exit automatically in 5 seconds accompanied with Bleep Bleep sound In case forget the admin code power on first then press within 3 seconds A sound Bleep indicates restore to factory defaults successfully Digit length is 2 means default admin code is 12 Digit length is 3 means defa
3. there is data stored in this position Press twice to delete the information in this position Press to quit setting mode Programing a group of fobs or cards In the setting mode Press 9 yellow light blinks then press O 1 Bleep sounds Input 3 digit number any one from 000 to 999 It indicates the card adding starts from this number For example enter 050 indicates the card is added from NO 50 Then add another 3 digit number indicates the quantity of cards to be added for example if 50 cards need to be added enter 050 If 150 cards are added enter 150 After Bleep is heard enter 8 digit card number of the first card or fob added or swipe the card or fob Bleep sound indicates the cards numbers added are successful Press to exit the setting mode Set door open time In the setting mode Press 1 yellow light blinks Then enter any 2 digit number from 00 to 99 Bleep sounds and yellow light stops blinking indicate the setting is successful 00 99 means the delay time For example 05 means the door open time is 5seconds delayed If time is set as 00 it means swipe a card once to open the door and swipe the card once again to close the door immediately Press to exit the setting mode The pickproof alarm The built in buzzer will sound a continuous Bleep Bleep If the photoresistor sensor is directly exposed to the light The buzzer will be off automatically in 60 seconds or when the light is no l
4. EZ PROX SINGLE DOOR PROXIMITY DOOR ENTRY USER MANUAL esp www espuk com Contents EZ PROX and back plate EZ PROX remote 10 x Tags Equipment required for controlling one door 12 volt DC power supply 2 amp minimum EV BPS Lock Magnetic EVML 250 Yale type keep 12 volt lock enter D Push to exit button EVEXIT Green break glass emergency release EVEBG Note for use with Magnetic lock only Functions of the EZ PROX The EZ PROX can control one door by use of tags Programmable door open time 00 to 99 seconds 1000 Tags can be programmed Door closed function contact required Programmable rear tamper Internal buzzer for tamper monitoring auto cut off after 1 minute Functions of EZ PROX remote e Two No 7 LRO3 AAA 1 5V alkaline batteries e Enter corresponded number to replace the relative ID IC card and fob e Working current 0 5mA e Sensor distance all around 20cm Installation Before installation position the location where the controller unit is mounted Please operate it according to the following steps 1 Open the controller by loosening and removing the back case screw at the bottom with the spline tool 2 Use the provided drilling template to accurately locate and drill the required holes The four drilling holes are marked B 3 Use the screws provided to mount the back case on the wall Be sure to draw the wiring through the large centre hole in back case and kee
5. obs Elite Security Products Fax 01527 515143 Tel 01527 515150 email info espuk com www espuk com
6. onger detected or by entering the admin code Changing the Programming code In the setting mode Press 3 yellow light blinks Then input new administrator code twice The length of the new admin code must be the same as the old one Bleep sound means it modifies successfully Press to exit the setting mode Turn on off the pickproof alarm In the setting mode Press 6 yellow light blinks then press O 1 Bleep sound and yellow light stops blinks Pickproof alarm is turned off Press 6 yellow light blinks then press O 2 Bleep sound and yellow light stops blinks Pickproof alarm is turned on Press to exit the setting mode Turn on off fob or card number detection In the setting mode Press 2 yellow light blinks then press O 1 Bleep sound and yellow light stops blink to turn on the card number detection Press 2 yellow light blinks then press O 2 Bleep sound and yellow light stops blink to turn off the card number detection Press to exit the setting mode Programming a Master Fob or Card In the setting mode Press 7 1 Green light blinks indicates there is no master card or fob stored Then swipe a card or fob Bleep sounds indicates this card is added as a master card 2 Green light turns on indicates there is master card Press twice to delete this master card or fob Then green light blinks New master card or fob can be added Swipe a card or fob and Bleep sounds
7. p level 4 Connected accurately the system wiring following the label enclosed on the rear 5 Put the unit back and screw it on by using the spline tool Hole Screw anchor eS Back cover Indicator Hole e Bell button a 4 oe Screw 201 75mm Remote control IR sensor Wiring Diagram Red power DC input 12V 24V Black power J AC input 12V 24V Brown door status detecting Orange unlocking button 1 Yellow DATA 1 Green GND Blue Door bell Purple Door bell Gray DATA 0 White NO 1 Pink COM 1 Aqua NC 1 Shielded ground t_ C1 m Red DC input 12V 24V Black oJ AC input 12V 24V Brown o Door magnet Orange Button Yellow DATA 1 Green GND Blue Purple DC Gray DATAO I 05D390K White NO 1 Pink COM1 5 _ Aqua NC 1 Shielded ground _ Wiring Diagram for Maglock EV BPS a UUUUUUUL e Cu te O O Z E lock DC out Push button Timer NC GND PB Oj 0 20 secs x zZ Maglock Capacitor a 0 47uF 100v Emergency door release 240vAC INPUT Exit Button O Wiring Diagram for Yale Release EV BPS
8. ult admin code is 123 Digit length is 4 means default admin code is 1234 Digit length is 5 means default admin code is 12345 Digit length is 6 means default admin code is 123456 Max is 6 The access control will be locked for 60 seconds if input wrong codes continuously or swipe the invalid card for 5 times both the keypad operating and the card swiping are not available during the 60 seconds Detect the door status after someone opens the door and closes it the system will automatically detect the door status and lock the door even though it is still in delay period Set the digit length of password Press 9 yellow LED blinks then enter O 4 Bleep sounds Input the digit X X 2 3 4 5 6 2 means the password code digit length is 2 00 99 3 means the password code digit length is 3 000 999 The rest may be deduced by analogy and the maximum is 6 digits Bleep sound means the setting of digit length is successful If the sound is Bleep Bleep Bleep it means new digit length is the same as the current one and the new setting is invalid Press to exit the setting mode Notice Once the digit length is changed all cards added will be deleted and cleared automatically Technical Specifications Working temperature 10 55 C Voltage DC 12V 24V AC 12V 24V Working current lt 120mA Standby current lt 90mA Card mode 1D IC card Effective distance lt 5CM Capacity 1000 Cards or F
Download Pdf Manuals
Related Search
EZ PROX ez-proxy ezproxy ugm ezproxy unibo ezproxy ulb ez proxy vfu ez proxy ump ezproxy uns ezproxy utm ezproxy jlu ez proxy hnu ezproxy lsmu ezproxy usj ez proximity card ez proxy vetuni ezproxy usim
Related Contents
Fujifilm FinePix Z950EXR User's Manual capteurs sans fil art. 30004001c, 30004010c, 30004011c Hook Eng. Keysight-Agilent DSOX2024A Datasheet Equip Network Tool Case Copyright © All rights reserved.
Failed to retrieve file