SyStem deScription i. SyStem controL By cAr
Contents
1. Ifyou want to program new remote control you must also re program all remotes which are already programed in system 5 System allows you to porgram up to 10 remote controls When programming new remotes system automatically erase already programmed remotes Note The device TS 100 has remote control working in the zone of 433 92 MHz Please ask you dealer for declaration of confornity Ill SYSTEM CONTROL BY ORIGINAL VEHICLE REMOTE CON TROL ALARM ACTIVATION Press the lock button on original vehicle remote control Siren sounds once or not according to system setings Directional lights flash 1x or so many times as when you locking the car with original remote control from vehicle Central locking system will lock alarm will activate itself and immobilization circuit will be activated after ignition turned ON After 8 or 40 sec according to settings is system active LED diode flashes slowly 7 All sensors are active If any sensor is triggered within 8 or 40 seconds siren beeps 2x and system automatically skip this sensor until it be not triggered again If any door or hood is open within 8 or 40 sec siren beeps 4 times If trunk is open siren beeps 2 times ALARM DEACTIVATION Press the unlock button on the original vehicle remote control Siren beeps twice or not according to system settings If siren beeps 4 times after 2 alarm deactivation alarm w2. after alarm deactiva tion alarm was triggered during guarding directional lights flashes 2x If directional lights flashes 4x alarm was triggered during guarding central locking system unlocks and immobilizer is deactivated If there was alarm triggered during guarding LED diode indicates which input or sensor was triggered by number of flashes LED DIODE SIGNALIZATION IF ALARM WAS TRIGGERED 1 flash additional sensor 4 flashes engine compartment 2 flashes ultrasonic sensor 5 flashes trunk 3 flashes door contacts 6 flashes ignition turned ON EMERGENCY PANIC ALARM Always when you press buttons Gand d at the same time siren will sound and directional lights will flash for 30 seconds Deactivate panic alarm by pressing button Bord Note on remote control RC MOTO activate PANIK alarm by same way or press button I for 1 second a for more turn on LED diode on the front part of remote always RC LINE i han lzer control set up time of LED shining when button press always only RC MAX o vehicle searching always only RC MOTO emergency PANIC alarm always only RC MOTO VEHICLE SEARCHING Car alarm must be activated Press button O Siren sounds 1x and directional lights flash 10x Press button to ends vehicle searching and to turn off car alarm Note on remote control RC MOTO activate vehicle searching by same way or by short press of button ANTI CAR JACK MO
3. check which button was pushed last time Buttons for locking and unlocking can be checked and therefore user can check whether he locked the car or not LOCK CHECK function is optional and turned off from factory You can activate the function by holding buttons O and for 2 seconds Icons for locking and unlocking will flash once and funtion is activated For deactivation use same process and they flash 2 times If the function is activated you can check the last pushed button by short pushing of button I After that the icon of locking or unlocking will light for aprox 0 8 sec depending on which button was pushed last time Warning When the LOCK CHECK function is activated battery life will be shorter LOW BATTERY INDICATOR ON THE REMOTE RC MAX If the battery indicator will flash in blue colour when locking or unlocking vehicle the battery in remote control is weak and you have to replace it with new one TORCH FUNCTION ON RC MAX RC METAL RC LINE By pressing button on remote controls RC MAX and RC METAL or button ie on remote control RC LINE for more than 1 second high power LED in front of the remote will light up If you keep pressing the button LED is turned ON and after pre set time turns OFF LED svieti pokial dr te stla en tla idlo a po uplynut nastavenej doby vypne even still holding the button pressed only RC MAX Time of LED turned ON can be set only RC MAX LED LIGHTS DURATION SETTING RC MAX Dur
4. code siren beeps once and LED diode turns OFF Now you are in PIN code programming menu 3 Press the service button LED starts flash slowly and you can enter new PIN code if the LED will flash so many times which is the new value of first PIN number press service button once First digit of new PIN code is save LED will start to flash again if the LED will flash so many times which is the new value of second PIN number press service button once Second digit of new PIN code is save LED will start to flash again if the LED will flash so many times which is the new value of third PIN number press service button once Third digit of new PIN code is save LED will start to flash again if the LED will flash so many times which is the new value of fourth PIN number press service button once Fourth digit of new PIN code is save LED will start to flash again 5 seconds after fourth digit is entered LED diode automatically display new PIN code by the number of flashes Display first digit of code 2 sec pause display second digit of code 2 sec pause etc 4 Turn ignition ON or system will automatically ends programming of new PIN code after 10 seconds from displaying the new PIN code PIN CODE RESET Disconnect the system from power supply Disjoint the jumper in control unit and connect the system to the power supply Within 3 seconds connect the jumper to the control unit PIN code will be set to factory defa
5. DE Function F11 is turned ON if ignition is turned ON and all doors are closed press buttons amp and CS simulta neously press and d on RC KEY for 1 second and open door within 8 seconds Anti car jack mode is now activated if you do not open any door within 8 seconds anti car jack mode is not activated 30 sec counting is started after closing last door LED diode starts flashing fast after 30 seconds siren beeps every 2 seconds After 20 seconds siren sounds per manent and directional lights flashing until ignition is turned OFF Immobilizaiton circuit is interrupted anti car jach mode can be deactivated by pressing buttons amp and d simultaneo usly press and d on RC KEY for 1 second or by using emergency deactivation ADDITIONAL TWO ZONE SENSOR siren sounds 1x and directional lights flashes 1x when first zone is triggered alarm is activated when second zone is triggered Siren sounds for 30 seconds and directional lights flashes for 30 seconds Maximum number of alarms caused by additional sensor while guarding the is 8x TRUNK OPEN press button amp on RC KEY press button for 1 sec Output for trunk open 300 mA will be activated for 0 5 sec if trunk is open system automatically omitted from guarding ultrasonic sensor ad ditional sensor and trunk input 4 seconds after trunk closing system guards these inputs again FUNCTION LOCK CHECK RC MAX This function allows you to
6. JAE KEETECTS 100 car ALARM USER MANUAL lt gt KEETEC SYSTEM DESCRIPTION KEETEC TS 50 is a car alarm designed for vehicles with 12 V supply voltage and is used to monitor the doors trunk hood In case of their disruption system is reporting alarm by optical indicator lights and audible siren signaling The system includes a built in ultrasonic sensor with adjustable sensitivity that in case of violation of vehicle interior reacts with alarm When car alarm is activated the system automatically blocks the starter circuit to prevent the unauthorized vehicle start up Car alarm is operated via a remote control which controls also central locking system of the vehicle and allows you to program up to 10 pieces of remote controls or is controlled by 2 original remote control from vehicle DESCRIPTION OF BUTTONS OF ALARM REMOTE CONTROLS CONDITIONS a system activation and central locking lock deactivated system activated system alarm triggered ignition turned ON b soundible vehicle searching c alarm termination d central locking lo ck B te ignition turned OFF deactivated i omission of ultrasonic sensor Ao e omision of ulrasonie sensor system W ignition turned OFF deactivated 3x 8 until 3sec omission of additional and ultrasonic sensor en activated system ignition turned ON a system deactivation cj b central locking unlock c alarm termination alarm triggered 8 cj eme
7. N Il PROGRAMMING REMOTE CONTROLS 1 Turn ignition ON and press service button 5 times within 8 seconds Turn ignition OFF If security mode is not active siren beeps 5 times system is now set to programming mode and LED starts flash If security mode is active function F19 enter it by Adigits PIN code LED starts flash slowly if the LED will flash so many times which is the value of first PIN number push the service button one time LED will start to flash again ifthe LED will flash so many times which is the value of second PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of third PIN number push the service button one time LED will start to flash again ifthe LED will flash so many times which is the value of fourth PIN number push the service button one time If you entered correct PIN code siren beeps 5 times and now you enter to the programming mode LED starts flash fast 2 Press any of button on remote control within 5 seconds If you dont press any of button within 5 seconds or ignition will be turned ON system automatically ends programming 3 Siren confirms programming by short beep Depending on which controller was programmed so many times siren beeps Successful programming of first remote control siren confirms by one beep second remote control siren confirms by two beeps etc A
8. as triggered during guarding Directional lights flashes 2x or so many times as when you unlocking the car with original remote control from vehicle If directional lights flashes 4 times after alarm deactivation alarm was triggered during guarding Central locking system unlock the vehicle alarm will deactivate itself and immobili zation circuit is linked LED diode is turned OFF If there was alarm triggered during guarding LED diode indicates which input was triggered by number of flashes 1 flash additional sensor 4 flashes engine compartment 5 flashes trunk 6 flashes ignition turned ON N K KEETEC EMERGENCY PANIC ALARM If you press lock button on original remote control for 3 times within 5 seconds PAN IC alarm will be activated Siren sounds and directional lights flasing for 30 seconds Alarm can be deactivated by pressing any button on remote control IV SERVICE MODE 1 turn ignition ON and press vallet button 2 times within 8 seconds 2 turn ignition OFF If security mode is not activated siren beeps 2x and LED diode is turned ON permanently Service mode is activated If security mode F19 is activated LED diode starts flashing slowly if the LED will flash so many times which is the value of first PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of second PIN number push the service button
9. ation of LED light can be adjusted from 1 to 30 sec or without limit Push buttons O and for 1 second Red LED will flash for 3 sec After those 3 sec the LED will start to flash in 1 sec intervals Press the button I for as long as you wish the light to be switched on max 30 sec If you don t press any button light duration will be unlimited Duration programming will automatically end after 30 sec LOCK CENTRAL LOCKING SYSTEM WHEN IGNITION IS TURNED ON when ignition is turned ON press button Gand central locking system will lock by pressing CS button central locking will be unlocked AUTOMATIC LOCK CENTRAL LOCKING AFTER IGNITION TURNED ON If this function is allowed system automatically locks central locking system after 20 seconds After ignition turns OFF central locking system will be unlocked With CAN BUS connection this feature is additionally conditioned to speeding over 5 km h AUTOMATIC REACTIVATION if you don t turn ignition ON or don t open the door after deactivation of car alarm system activates itself after 30 seconds automatically if function F16 is active central locking will lock after ractivation AUTOMATIC ACTIVATION AFTER CLOSING LAST DOOR car alarm will be activated automatically after 30 seconds after turning the ignition OFF and closing the last door If function F16 is active after activation system locks central locking system if you open door within 30 seconds after closing last
10. door car alarm will be activated after 30 seconds after closing them ALARM MEMORY car alarm even after disconnecting the power supply maintains the state in which it was before disconnecting 2 2 flashes ultrasonic sensor 3 flashes door contacts IMMOBILIZER After car alarm is turned ON immobilization circuit and output is active until alarm is turned OFF again AUTOMATIC ACTIVATION OF IMMOBILIZATION CIRCUIT 7 if function F12 is turned ON immobilization circuit will be automatically activated 2 after 5 minutes from ignition turned OFF Deactivate immobilization circuit by pressing unlock button or same way as at emergency deactivation AUTOMATIC ACTIVATION AFTER TRIGGERED ALARM when the alarm is triggered siren will sound for 30 seconds After that system stays 2 armed If the input that triggered the alarm is still disturbed after 30 seconds the system automatically ignore it until input become calm 2 SIREN AND DIRECTIONAL LIGHTS WHEN ALARM IS TRIGGERED When alarm is armed and is triggered by some of the inputs siren sounds and directional lights flashes for 30 seconds Alarm triggered by door contacs hood contact trunk contact and shock sensor can be repeated 8 times After disarming and 2 arming the system alarm from these inputs can be repeated 8 times again Alarm 2 triggered by turning ignition ON can be triggered infinitely times Siren still sounds until ignition is turned O
11. one time LED will start to flash again if the LED will flash so many times which is the value of third PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of fourth PIN number push the service button one time If you enterred correct PIN code siren beeps 2x and LED diode shine permanently Service mode is activated Deactivation of service mode Turn ignition ON and press the service button 2x within 8 seconds Turn ignition OFF Siren sounds 2x and LED turns OFF Service mode is deactivated V PIN CODE CHANGE 1 Turn ignition ON and press service button 10 times within 10 seconds 2 Turn ignition OFF If security mode is deactivated now you are in programing PIN code menu If security mode is active function F19 enter it by entering 4digits PIN code LED diode starts flashes slowly if the LED will flash so many times which is the value of first PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of second PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of third PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of fourth PIN number push the service button one time If you entered correct PIN
12. rgency PANIC alarm always N a anti car jack mode ignition turned ON C for Isec b termination of anti car jack mode activated anti car jack mode ignition turned ON activated anti car jack mode only RC KEY LOCK CHECK is turned OFF LOCK CHECK is turned ON a anti car jack mode xK d for lsec B termination of anti car jack mode a turn ON LOCK CHECK function b turn OFF LOCK CHECK function activation of LOCK CHECK function control of last pressed button on RC C43 for 2sec always only RC MAX for more than 1 sec turn on LED diode on the front part of remote control always RC MAX RC METAL Note Function Lock Check contains only remote controls RC MAX I SYSTEM CONTROL BY CAR ALARM REMOTE CONTROLS ALARM ACTIVATION press button O Siren beeps 1x or not see program menu F1 directional lights flash 1x central locking locks and immobilizer is activated after 8 or 40 sec see program menu F3 is system active LED diode flashes slowly All sensors are active If any sensor is triggered within 8 or 40 seconds system auto matically omitted this sensor until it will be calm again if doors or hood are not closed within 8 or 40 seconds siren beeps 4x If trunk is not closed within 8 or 40 seconds LED diode flashes fast and siren bees 2x ALARM DEACTIVATION press button ok siren beeps 2x or not see program menu F 1 If siren beeps 4x
13. ult number 4321 VI EMERGENCY DEACTIVATION 1 Open driver door and turn ignition ON 2 Press the service button so many times which is value of first digit of PIN code within 10 seconds and turn ignition OFF If security mode is disabled siren beeps twice directional lights flashes twice and now system is deactivated If security mode is active function F19 enter by 4digits PIN code LED starts flashing slowly if the LED will flash so many times which is the value of first PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of second PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of third PIN number push the service button one time LED will start to flash again if the LED will flash so many times which is the value of fourth PIN number push the service button one time If you entered correct PIN code siren beeps twice and directional lights flashes twice System is now deactivated
Download Pdf Manuals
Related Search