TPT15HD45revC 450KB Jan 10 2013 12:08:09 PM
Contents
1. AUDIO 5 Ol 12 VDC 5A MAX Figure 2 1 Rear panel views Power input captive screw connector Connect the included 12 VDC external power supply to the 2 pole female direct insertion captive screw connector The TP T 15HD 45 and the TP T A 45 share a single NOTE amp power supply Neither one can be remotely powered by the attached receiver SECTION A A Captive Screw Direct Insertion Connector A PO meee Power Supply Output Cord EZENN The two power supply leads must be kept separated while the power supply is plugged into an electrical outlet Remove power before wiring Power supply voltage polarity is critical Incorrect voltage polarity can damage the power supply and the transmitter Identify the power cord negative lead by the ridges on the side of the cord When stripping the wire ends please note that stripped wire ends that are too short may pull out from the captive screw connector and stripped wire ends that are too long could possibly touch and short together Captive screw digital audio input connector Connect the digital audio input cables from the TP T A 45 if installed to the 2 pole female direct insertion captive screw connector TP T 15HD 45 and TP T A 45 e Installation ee AUDIO AUDIO Digital Audio Input Captive Screw Direct Insertion Connector EZENN Remove power before wiring Meg The wire gauge should be 14 22 AWG and the maximum2. NTSC PAL composite video from a single source Connectors TP TISHD gts cos 1 15 pin HD female Mac and Sun SGI to VGA adapters are available Nominal level esencia uid Pu 1 V p p for Y of component video and S video and for composite video 0 7 V p p for RGB 0 3 V p p for R Y and B Y of component video and for C of S video Minimum maximum levels 0 3 V to 1 45 V p p with no offset at unity gain MPEC M M 75 ohms Horizontal frequency aveces tiros 15 KHz to 130 KHz Vertical frequency secseosecititetetessss 30 Hz to 150 Hz Return TOSS moti peso AD PURA 30 dB 9 5 MHz DC offset max allowable 100 mV Video output refer to the TP Receivers Family User s Manual part 68 547 02 Audio audio models Number signal type 1 set of analog proprietary signals Connectors TP TA 5 eseese 1 2 pin direct insertion captive screw connector Frequency response neenon 20 Hz to 20 kHz 0 05 dB THD Noise 2 ouciietes verona tides 0 03 1 kHz 0 396 20 kHz at nominal level A 2 TP T 15HD 45 and TP T A 45 Reference Information cd gt 63 dB at maximum output unweighted Crosa lai eth eaten 80 dB 9 1 kHz fully loaded Stereo channel separation gt 80 dB 9 1 KHz ahud nc gt 33 dB 20 Hz to 20 kHz Audio input audio models Number signal type TP T A 5 vccncdccntanvssoasereeswess 1 stereo unbalanced Connectors TP TA 45 1 3 5 mm mini ja
3. either case the entire cabling system should be tested A complete test measures cable length and tests the wire map attenuation NEXT PSNEXT ELFEXT PSELFEXT return loss ACR and PSACR All of these tests are critical for digital data transfer While all of these tests are important indicators of the quality of the cable termination the most critical testing parameters for video transfer are wire map T 568 A or T 568 B termination and pair length measurements The largest concern is equalization of skew between cable pairs Cable systems of 300 feet or less should exhibit no transmission problems if they pass at least CAT 5e or preferably CAT 6 D5 channel certification testing The Microtest OMNI SCANNER 2 performs comprehensive certification testing to the proposed CAT 6 standards Other manufacturers also make testing equipment The tests include advanced diagnostics for troubleshooting the cause and location of many cable and termination problems For simple installation testing the Microtest MICRO SCANNER PRO tests wire map and cable length including individual cable pair length delay problems CAT 5 TP cable can lead to registration errors between the red green and blue video signals Pair skew can be measured with test equipment or identified by viewing a crosshatch test pattern with a critical eye to determine if either the red green or blue video image leads appears to the left of the other two video images These i
4. la pared Protecci n del cables de alimentaci n Los cables de alimentaci n el ctrica se deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos Reparaciones mantenimiento Solicitar siempre los servicios t cnicos de personal calificado En el interior no hay partes a las que el usuario deba acceder Para evitar riesgo de electrocuci n no intentar personalmente la reparaci n mantenimiento de este equipo ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos Ranuras y aberturas Si el equipo posee ranuras o orificios en su caja alojamiento es para evitar el sobrecalientamiento de componentes internos sensibles Estas aberturas nunca se deben obstruir con otros objetos Bater a de litio Existe riesgo de explosi n si esta bater a se coloca en la posici n incorrecta Cambiar esta bater a nicamente con el mismo tipo o su equivalente recomendado por el fabricante Desachar las bater as usadas siguiendo las instrucciones del fabricante FCC Class B Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instru
5. resulting from any defect in this product even if Extron Electronics has been advised of such damage Please note that laws vary from state to state and country to country and that some provisions of this warranty may not apply to you Quick Start Guide TP T 15HD 45 A 45 ep Vade Installation and service must be performed by authorized personnel only These units must be installed in accordance with national and local electrical codes Step 1 Power off all devices and disconnect them from the power source Step 2 Connect the UTP cable from the receiver to the 8 pin connector on the TP T 15HD 45 To wire the connector see Rear Panel Connectors in chapter 2 for the pinout table CAUTION Do not connect the TP T 15HD 45 to a computer data or telecommunications network Step 3 Connect the external power supply to the transmitter Step 4 Using the 15 pin front panel HD connector attach a computer input to the transmitter and a display output to the receiver See the example application diagram below Projector Mounting Bracket Extron s 2 8 Mounting TP R 15HD A S Bolt Twisted Pair wh Receiver CAT 5 6 or Extron Skew Free UTP Cable Up to 500 feet Extron TPT A 45 TP T 15HD 45 Twisted Pair Transmitters TP T 15HD 45 and TP T A 45 e Quick Start Guide QS 1 Quick Start Guide TP T 15HD A 45 cont d Step 5 If the TP T A 45 is being installed connect the TP T A 45 to the T
6. NPUT 1 amp 2 7 amp 8 3 amp 6 4 amp 5 Twisted Wire Pairs T o INPUT Extron Extron 3 Power input captive screw connector Connect power input cables to the 2 pole female direct insertion captive screw Figure 2 2 Front panel views connector Power LED indicator The LED lights green whenever power o 12 VDC is applied r pn 10 5 1 6 2 15 pin HD video input connector Connect Ceeecec Power Input Captive Screw Mo PRECOR eee Direct Insertion Connector COPEI VIGE pur 5 11 Mei Input only sync signals no video Female EZENN Remove power before wiring signals on the sync pins 13 and 14 For component video use the R R Y and R return pins 4 Digital audio output captive screw connector Connect the pins 1 and 6 G Y and G return pins pins 2 and 7 digital audio output cables to the 2 pole female direct insertion and B B Y and B return pins pins 3 and 8 captive screw connector For S video use the R R return C chroma G and G return Y luma pins E AUDIO For composite video use the G pin and the associated AUDIO return pin For additional genlocked video signals use Digital Audio Output the R B and associated return pins Captive Screw Direct Insertion Connector The TP T 15HD 45 and TP T A 45 are only compatible with the RGBHV and RGBS VTR series of receivers EZENN Remove power before wiring Tip L Ring R 3 3 5 mm stereo mini jack i
7. P T 15HD 45 See Rear Panel Connectors in chapter 2 Noia The TPT 15HD 45 may be used as a stand alone video only module without the TP T A 45 The TP T A 45 derives its power from the TP T 15HD 45 Step 6 Connect and power up all input and output devices then apply power to the TP T 15HD 45 power supply and test for the display and or audio outputs If a problem is encountered check all connections before proceeding further Step 7 If the previous display and or audio test was successful power off and disconnect all equipment detach cables and install the TP T 15HD 45 and TP T A 45 if installed modules See Mounting in chapter 2 Mey Ifthe transmitter is to be wall mounted and the power supply will be inaccessible power must be applied to the transmitter s power supply before final mounting Step 8 Connect all device and power cables Power up all input and output devices apply power to the transmitter and receiver and test for the display and or audio QS 2 TPT 15HD 45 and TP T A 45 e Quick Start Guide Table of Contents Chapter 1 Introduction sssees 1 1 Features s sseeeeeeeeee eene 1 2 Chapter 2 Installation 2 1 Rear Panel Connectors eese 2 2 Front Panel Connectors and Indicators 2 5 Cabling and Setup essus 2 5 Compatibility with other Extron prod
8. ansmission distances between the TP T 15HD 45 transmitter and compatible Extron receivers at 60 Hz Video Recommended maximum Recommended maximum format range to VTR series range to all other resolution and TP R 15HD A Extron receivers Composite 800 feet 1000 feet S video 800 feet 1000 feet Component 800 feet 1000 feet 640 x 480 500 feet 1000 feet 800 x 600 400 feet 800 feet 1024 x 768 300 feet 600 feet 1280 x 1024 200 feet 400 feet 1600 x 1200 150 feet 300 feet VTROO1 is not compatible with component composite or S video Mei I is possible to exceed the recommended distances however image quality may be reduced Features 1 2 e 45 mm opening compatibility The TP T 15HD 45 and TP T A 45 are designed to fit into a 45 mm mounting frame that is popular throughout Europe The plate may be wall mounted or floor box mounted e Extron TP product compatibility The TP T 15HD 45 and TP T A 45 are compatible with several Extron TP receivers and matrix switchers including the TP R 15HD A TP R BNC A TP R BNC AV TPX 88 TPX 88A and the VTR series RGBHV and RGBS only TP T 15HD 45 and TP T A 45 Introduction 2 2 TP T 15HD 45 and TP T A 45 Chapter Two Installation Rear Panel Connectors Front Panel Connectors and Indicators Cabling and Setup Installation Rear Panel Connectors 2 2 TP T 15HD 45 TPTA 45 Extron ER TP T 15HD 45 D TPTA 45 12 VDC AUDIO _ SAMAX AUDIO
9. art number Power supply universal 28 071 01 TP T 15HD 45 only 12 VDC 1 0 A ey All nominal levels are at 10 Neg Specifications are subject to change without notice Tweeker small screw driver TP T 15HD 45 TP T A 45 User s Manual Power supply ships with 70 055 01 IEC power cord Optional accessories Description Part number VGA cable 6 male to male 26 238 01 VGA with audio cable 6 male to male 26 490 02 Enhanced Skew Free A V UTP cables 26 569 xx assorted lengths Plenum Enhanced Skew Free A V UTP 26 570 xx cables Enhanced Skew Free A V UTP bulk 22 141 03 cable 1000 Plenum Enhanced Skew Free A V UTP 22 142 03 bulk cable 1000 Plenum Enhanced Skew Free A V UTP 22 141 04 bulk cable 1000 meters A 4 TP T 15HD 45 and TP T A 45 e Reference Information A 5 TP T 15HD 45 and TP T A 45 e Reference Information Reference Information cont d TP T 15HD 45 and TP T A 45 Reference Information
10. ceeding further If the previous display and or audio test was successful power off and disconnect all equipment detach cables and install the TP T 15HD 45 and or TP T A 45 modules See Mounting in this chapter NOTE If the transmitter or receiver is to be wall mounted and the power supply will be inaccessible power must be applied to the power supply before final mounting Connect all device and power cables Power up all input and output devices apply power to the transmitter and receiver and test for the display and or audio Compatibilty with other Extron products As a pair the TP T 15HD 45 and TP T A 45 are compatible with the following Extron receivers and matrix switchers e TP R15HD A e TP R BNC A TP R BNC AV e TPX 88A TP T 15HD 45 and TP T A 45 Installation As a stand alone transmitter the TP T 15HD 45 is compatible with e VTR001 VTR001 AAP and VTR001 MAAP RGBHV RGBS only e TPX 88 Cable testing Skew To ensure proper cable termination each transmission cable system that uses CAT 5e or CAT 6 cable should be tested Extron UTP23SF cable does not need to be tested Testing the cable from the transmitter and receiver gives the most accurate indications of cable problems There are two varieties of cable runs simple runs in which a single cable is terminated only at the transmitter and receiver and complex runs which can include patch bays and multiple terminations and lengths of cable In
11. ck Impedance TIPTA c erenn gt 10k ohms unbalanced DC coupled Nominal level 10 dBV 316mV Maximum level 5 5 dBu unbalanced at 170 THD N Med 0 dBu 0 775 Vrms OdBV 1 Vrms OdBV 2 dBu Audio output refer to the TP Receivers Family User s Manual part 68 547 02 General Power TPT15HD45 soisissa 12 VDC 1 0 A external TP TAAS ccssectenrssvaneredeecniaats Shared with the TP T 15HD 45 transmitter Temperature humidity Storage 40 to 158 F 40 to 70 C 10 to 90 noncondensing Operating 32 to 122 F 0 to 50 C 10 to 90 noncondensing Rack mount eere No but mountable in a 45 mm x 45 mm opening ErclosUte D Dea Metal Enclosure dimensions TP T 15HD 45 TP T A 45 Faceplate sonenn 1 8 H x 1 7 W x 0 8 D 45 mm H x 45 mm W x 20 mm D Ib gni HT 1 1 Hx 1 6 W x 1 2 D 29 mm H x 41 mm W x 30 mm D Depth excludes connectors Product weight All models cveuiscnetensousecosusicg 1 0 lbs 0 5 kg Shipping weight All models erencicarecesertocizenaesis 3 lbs 2 kg TP T 15HD 45 and TP T A 45 e Reference Information A 3 Reference Information cont d WOT Oi eesemit rita Emobum dU ISTA 1A in carton International Safe Parts Lists Transit Association Companies seetutenvaeHn CE FCC Class A VCCI AS NZS ICES Included parts L4 E 5 ND 30 000 hours an oLa E ht 3 years parts and labor Description P
12. cked by other objects Lithium battery There is a danger of explosion if battery is incorrectly replaced Replace it only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Avertissement Alimentationse Ne faire fonctionner ce mat riel qu avec la source d alimentation indiqu e sur l appareil Ce mat riel doit tre utilis avec une alimentation principale comportant un fil de terre neutre Le troisi me contact de mise la terre constitue un dispositif de s curit n essayez pas de la contourner ni de la d sactiver D connexion de l alimentation Pour mettre le mat riel hors tension sans danger d connectez tous les cordons d alimentation de l arri re de l appareil ou du module d alimentation de bureau s il est amovible ou encore de la prise secteur Protection du cordon d alimentation e Acheminer les cordons d alimentation de mani re ce que personne ne risque de marcher dessus et ce qu ils ne soient pas cras s ou pinc s par des objets R paration maintenance Faire ex cuter toutes les interventions de r paration maintenance par un technicien qualifi Aucun des l ments internes ne peut tre r par par l utilisateur Afin d viter tout danger d lectrocution l utilisateur ne doit pas essayer de proc der lui m me ces op rations car l ouverture ou le retrait des couvercles risquent de l exposer de haute
13. ctions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This unit was tested with shielded cables on the peripheral devices Shielded cables must be used with the unit to ensure compliance Extron s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase In the event of malfunction during the warranty period attributable directly to faulty workmanship and or materials Extron Electronics will at its option repair or replace said products or components to whatever extent it shall deem necessary to restore said product to proper operating condition provided that it is returned within the warranty period with proof of purchase and description of malfunction to USA Canada South America and Central America Europe Afr
14. die einen elektrischen Schock verursachen k nnen herrschen Dieses Symbol soll den Benutzer darauf aufmerksam Achtung Lesen der Anleitungen Bevor Sie das Ger t zum ersten Mal verwenden sollten Sie alle Sicherheits und Bedienungsanleitungen genau durchlesen und verstehen Aufbewahren der Anleitungen Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie aufbewahren damit Sie im Bedarfsfall darauf zur ckgreifen k nnen Befolgen der Warnhinweise Befolgen Sie alle Warnhinweise und Anleitungen auf dem Ger t oder in der Benutzerdokumentation Keine Zusatzger te e Verwenden Sie keine Werkzeuge oder Zusatzger te die nicht ausdr cklich vom Hersteller empfohlen wurden da diese eine Gefahrenquelle darstellen k nnen Instrucciones de seguridad Espanol Este s mbolo seutiliza para advertir al usuario sobre instrucciones importantes de operaci n y mantenimiento o cambio de partes que se desean destacar en el contenido de la documentaci n suministrada con los equipos Este s mbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protecci n aislante que puedan encontrarse dentro de la caja o alojamiento del producto y que puedan representar riesgo de electrocuci n Precaucion Leer las instrucciones Leer y analizar todas las instrucciones de operaci n y seguridad antes de usar el equipo Conservar las instrucciones Conservar las instruccione
15. distance between the modules should not exceed 25 feet Video and audio output 8 pin spring force connector Attach a UTP cable from a TP receiver to the 8 pin spring force connector Wire this connector according to the following pin assignment table Twisted Pair Pin Assignments TIA EIA T 568 A TIA EIA T 568 B Wire Color Wire Color red vertical sync white green white orange red vertical sync green orange digital audio white orange white green green blue blue green white blue white blue digital audio orange green blue horizontal sync white brown white brown blue horizontal sync brown brown Nozi T 568 A is recommended when using Extron UTP23SF cable eT el Do not connect the transmitter to a computer data or telecommunications network Using the included tweeker tool and observing the correct wiring colors in the previous table insert the stripped wire ends see note below of the twisted pairs into the spring force connector as shown in the following diagram NOTE Strip approximately 0 43 1 1 cm of insulation from each individual wire on one end of a TP cable TP T 15HD 45 and TP T A 45 Installation 2 3 Installation cont d Front Panel Connectors and Indicators 12345678 an Mn TP T 15HD 45 TP TA 45 J 2755 ACA KKK N Ay 7 AWWW Zeer x J 4 xt O e LZ A NN hy Cg AN COMPUTER SEEL o _ I
16. ica and the Middle East Extron Electronics Europe Extron Electronics Beeldschermweg 6C 1001 East Ball Road 3821 AH Amersfoort Anaheim CA 92805 USA The Netherlands Asia Japan Extron Electronics Japan Extron Electronics Asia Kyodo Building 135 Joo Seng Road 04 01 16 Ichibancho PM Industrial Bldg Chiyoda ku Tokyo 102 0082 Singapore 368363 Japan This Limited Warranty does not apply if the fault has been caused by misuse improper handling care electrical or mechanical abuse abnormal operating conditions or non Extron authorized modification to the product If it has been determined that the product is defective please call Extron and ask for an Applications Engineer at 714 491 1500 USA 31 33 453 4040 Europe 65 6383 4400 Asia or 81 3 3511 7655 Japan to receive an RA Return Authorization number This will begin the repair process as quickly as possible Units must be returned insured with shipping charges prepaid If not insured you assume the risk of loss or damage during shipment Returned units must include the serial number and a description of the problem as well as the name of the person to contact in case there are any questions Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality performance merchantability or fitness for any particular use In no event will Extron Electronics be liable for direct indirect or consequential damages
17. mages can be minimized or eliminated by one of the following methods TP T 15HD 45 and TP T A 45 Installation 2 7 Installation cont d e Switch to Extron s UTP23SF cable e Addaskew compensation cable equal to the length of pair skew to the receiver s output e Install an SEQ 100 15HD Skew Equalizer on the receiver s video output and adjust the skew for the leading video image Mounting The TP T 15HD 45 and TP T A 45 are designed to fit into a wall mountable or floor box mountable 45 mm mounting frame The following application diagram illustrates one example of installing these devices Projector Mounting Bracket Extron 5 27 5 amp Mounting TP R 15HD A 5s Bolt S Twisted Pair v Receiver as S Q9 CAT 5 6 or Extron Skew Free UTP Cable Up to 500 feet Extron TPT A 45 TP T 15HD 45 Twisted Pair 2 8 TP T 15HD 45 and TP T A 45 e Installation TP T 15HD 45 and TP T A 45 Appendix Reference Information Specifications Parts Lists Reference Information Specifications Video video models Number signal type s oneietoenites 1 set of proprietary analog signals Connectors IF TOE AO esas 1 8 pin spring force captive wire connector Video input video models Number signal type TPTISED45 2eeettoa 1 analog RGBHV RGBS RGsB component video or S video or 1 S video and 1 NTSC PAL SECAM composite video from a single source or 3
18. nput dL Connect unbalanced audio to this aa gt stereo jack Wire the male plug as M nere lial shown on the right Sleeve Input only analog and line level audio signals on this connector Cabling and Setup To install the TP T 15HD 45 and TP T A 45 models follow these steps 2 4 TP T 15HD 45 and TP T A 45 Installation TP T 15HD 45 and TP T A 45 Installation 2 5 Installation cont d 1 Turn all of the equipment off and if applicable disconnect it from the power source 2 Connect the TP T 15HD 45 and its receiver to either end of the UTP cable See Cable testing and Skew delay problems in this chapter NejizH For best results use Extron UTP23SF cable available in bulk or in various preterminated lengths If necessary regular CAT 5 CAT 5e and CAT 6 cable may be used 3 Connect the external power supply to the TP T 15HD 45 and TP T A 45 if installed See Rear Panel Connectors in this chapter gt If the TP T A 45 is being installed connect the TP T A 45 to the transmitter See Rear Panel Connectors in this chapter Connect an output display device to the output connector of the receiver CINE Connect a computer to the 15 pin video input connector of the transmitter gt Connect and power up all input and output devices then apply power to the TP T 15HD 45 power supply and test for the display and or audio outputs If a problem is encountered check all connections before pro
19. omponenten des Ger tes sind wartungsfrei Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall dieses Ger t selbst ffnen da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und oder andere Gefahren bestehen Schlitze und ffnungen Wenn das Ger t Schlitze oder L cher im Geh use aufweist dienen diese zur Vermeidung einer berhitzung der empfindlichen Teile im Inneren Diese Offnungen d rfen niemals von anderen Objekten blockiert werden Litium Batterie e Explosionsgefahr falls die Batterie nicht richtig ersetzt wird Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp der auch vom Hersteller empfohlen wird Entsorgen Sie verbrauchte Batterien bitte gem den Herstelleranweisungen Advertencia Alimentaci n el ctrica Este equipo debe conectarse nicamente a la fuente tipo de alimentaci n el ctrica indicada en el mismo La alimentaci n el ctrica de este equipo debe provenir de un sistema de distribuci n general con conductor neutro a tierra La tercera pata puesta a tierra es una medida de seguridad no puentearia ni eliminaria Desconexi n de alimentaci n el ctrica Para desconectar con seguridad la acometida de alimentaci n el ctrica al equipo desenchufar todos los cables de alimentaci n en el panel trasero del equipo o desenchufar el m dulo de alimentaci n si fuera independiente o desenchufar el cable del recept culo de
20. rked on the equipment or in the user information Avoid Attachments Do not use tools or attachments that are not recommended by the equipment manufacturer because they may be hazardous Consignes de S curit Francais Ce symbole sert avertir l utilisateur que la documentation fournie avec le mat riel contient des instructions importantes concernant l exploitation et la maintenance r paration Ce symbole sert avertir l utilisateur de la pr sence dansleboitierdel appareil de tensions dangereuses non isol es posant des risques d lectrocution Attention Lire les instructions Prendre connaissance de toutes les consignes de s curit et d exploitation avant d utiliser le mat riel Conserver les instructions Ranger les consignes de s curit afin de pouvoir les consulter l avenir Respecter les avertissements Observer tous les avertissements et consignes marqu s sur le mat riel ou pr sent s dans la documentation utilisateur Eviter les pi ces de fixation Ne pas utiliser de pi ces de fixation ni d outils non recommand s par le fabricant du mat riel car cela risquerait de poser certains dangers Sicherheitsanleitungen Deutsch Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung Instandhaltung geben machen da im Inneren des Geh uses dieses Produktes gef hrliche Spannungen die nichtisoliert sind und
21. s de seguridad para futura consulta Obedecer las advertencias Todas las advertencias e instrucciones marcadas en el equipo o en la documentaci n del usuario deben ser obedecidas Evitar el uso de accesorios No usar herramientas o accesorios que no sean especificamente recomendados por el fabricante ya que podrian implicar riesgos Warning Power sources This equipment should be operated only from the power source indicated on the product This equipment is intended to be used with a main power system with a grounded neutral conductor The third grounding pin is a safety feature do not attempt to bypass or disable it Power disconnection To remove power from the equipment safely remove all power cords from the rear of the equipment or the desktop power module if detachable or from the power source receptacle wall plug Power cord protection Power cords should be routed so that they are not likely to be stepped on or pinched by items placed upon or against them Servicing Refer all servicing to qualified service personnel There are no user serviceable parts inside To prevent the risk of shock do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards Slots and openings If the equipment has slots or holes in the enclosure these are provided to prevent overheating of sensitive components inside These openings must never be blo
22. s tensions et autres dangers Fentes et orifices Si le bo tier de l appareil comporte des fentes ou des orifices ceux ci servent emp cher les composants internes sensibles de surchauffer Ces ouvertures ne doivent jamais tre bloqu es par des objets Lithium Batterie Il a danger d explosion s ll y a remplacment incorrect de la batterie Remplacer uniquement avec une batterie du meme type ou d un ype equivalent recommande par le constructeur Mettre au reut les batteries usagees conformement aux instructions du fabricant Vorsicht Stromquellen Dieses Ger t sollte nur ber die auf dem Produkt angegebene Stromquelle betrieben werden Dieses Ger t wurde f r eine Verwendung mit einer Hauptstromleitung mit einem geerdeten neutralen Leiter konzipiert Der dritte Kontakt ist f r einen Erdanschluf und stellt eine Sicherheitsfunktion dar Diese sollte nicht umgangen oder aufer Betrieb gesetzt werden Stromunterbrechung Um das Ger t auf sichere Weise vom Netz zu trennen sollten Sie alle Netzkabel aus der R ckseite des Ger tes aus der externen Stomversorgung falls dies m glich ist oder aus der Wandsteckdose ziehen Schutz des Netzkabels Netzkabel sollten stets so verlegt werden daf sie nicht im Weg liegen und niemand darauf treten kann oder Objekte darauf oder unmittelbar dagegengestellt werden k nnen Wartung Alle Wartungsmafnahmen sollten nur von qualifiziertem Servicepersonal durchgef hrt werden Die internen K
23. ucts 2 6 CBDIG TOSEITI E E A E 2 7 Skew delay problems ss nsssssssnssssssnsnnnnnnrnrrnenenrnnnnnnnnnnennen n 2 7 MONENG aca seeseatutusa s raptus seaceeeceraceteaenconsradetaauceasermeatansouameent 2 8 Appendix Reference Information A 1 Specifications sooo vprpdn parendevrediwcu YR rA ERO Fedib n A 2 Parts LISIS eee nee ee eee eee A 5 Included parts RETRO REO A 5 Optional accessories ccccceeesseceeecceesseeeeeeceeesseeeeesesaseeeeeeens A 5 All trademarks mentioned in this manual are the properties of their respective owners 68 924 01 Rev C 05 05 TP T 15HD 45 and TP T A 45 e Table of Contents i Table of Contents cont d 2 TP T 15HD 45 and TP T A 45 Chapter One Introduction Features ii TP T 15HD 45 and TP T A 45 e Table of Contents Introduction Ss M e The Extron TP T 15HD 45 twisted pair transmitter and the matching TP T A 45 audio input module provide a system for sending RGBHV RGBS RGsB component composite or S video and stereo audio signals over Extron Skew Free A V UTP cable or CAT 5 5e 6 UTP cable to a compatible TP or VTR receiver An external 12 VDC power supply provides power to both the TP T 15HD 45 and the TP T A 45 ono The TP T A 45 inputs unbalanced audio through a 3 5 mm stereo phono jack and outputs digital audio to the TP T 15HD 45 transmitter The following table specifies the maximum recommended tr
24. wt Ase Extron Electronics USA Extron Electronics Europe Extron Electronics Asia x 1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road 404 01 Vnd 3 Anaheim CA 92805 3821 AH Amersfoort PM Industrial Building USA The Netherlands Singapore 368363 Surio 714 491 1500 31 33 453 4040 65 6383 4400 www extron com Fax 714 491 1517 Fax 31 33 453 4050 Fax 65 6383 4664 2005 Extron Electronics All rights reserved Extron Electronics Japan Kyodo Building 16 Ichibancho Chiyoda ku Tokyo 102 0082 Japan 81 3 3511 7655 Fax 81 3 3511 7656 Extron Electronics TON INTERFACING SWITCHING AND DISTRIBUTION uno User s Manual COMPUTER z it AUCH E INPUT Extron TP T 15HD 45 and TP T A 45 Twisted Pair Video and Audio Transmitters 68 924 01 Rev C 05 05 Precautions Safety Instructions English This symbol is intended to alert the user of important operating and maintenance servicing instructions in the literature provided with the equipment This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may present a risk of electric shock Caution Read Instructions Read and understand all safety and operating instructions before using the equipment Retain Instructions The safety instructions should be kept for future reference Follow Warnings Follow all warnings and instructions ma
Download Pdf Manuals
Related Search