iOval Bluetooth inductive loopset manual
Contents
1. S N DO iOval Bluetooth inductive loopset manual Communication Technology Led indicator Kl multi function button Inductive loop Movable microphone Charging socket Ez button volume Getting Started The Bluetooth inductive loop comes with a rechargeable battery included The battery is not fully charged when it is new For first time use it takes 3 hours to fully charge the battery Afterwards it will take about 1 hour to fully charge the battery With the battery fully charged the talking time will be 5 to 6 hours and the stand by time will be about 90 hours 1 Plug the travel charger into an AC socket 2 Connect the charger with the inductive loop The green indicator will turn on when charging 3 When the battery is full the indicator of the Bluetooth inductive loop will turn off 4 Pair up the Bluetooth loopset with a mobile phone remember that the loopset has to be turned off Buttons Function Black button on the top of the cover K1 power on off epairing with a mobile phone e answering ending calls redial evoice dialing Grey side button K2 volume adjusting switching the call between inductive loop or mobile phone Pairing the Bluetooth inductive loop You are required to pair the Bluetooth inductive loop with your mobile phone before using it Step 1 The Bluetooth inductive loop must be powered off before initiating pairing When initiate pairing Keep holding K1 button for about 8 second2. affected by following two factors If your mobile phone local signal is very weak the Bluetooth inductive loop call quality is bad relative too Noise become bigger if the distance exceeds the standard between the mobile phone and Bluetooth inductive loop In other cases please see the attached earpiece manual 5 The person You are talking with hears interferences Make sure that the inductive loop s microphone is not too close to the mobile phone optimal distance between the microphone and a phone is gt 60cm Product Maintenance Use of non original accessories may result in performance deterioration injury products damage electronic shock and warranty termination Attempt to disassemble Your Bluetooth inductive loop may damage it and the warranty will be void Do not put the Bluetooth inductive loop in a dusty place Do not allow children to play with Your Bluetooth inductive loop as they may injure themselves and damage the Bluetooth inductive loop as well Do not place the Bluetooth inductive loop in an extremely hot or cold temperature when the Bluetooth inductive loop will not be used for a while Battery Information New Batteries For first time use plug the adapter into the Bluetooth inductive loop and charge it at least 3 hours until the indicator runs off The rechargeable battery has a long service life if treaded with care The battery can only be charged in a temperature range of 10 C to 45 C The bat
3. 1 Using voice dialing press K1 button you will hear beep signal and then the indicator will be flashing very fast Say the name of the person who you want to call 2 Using mobile phone keys to make a call Dial the number on the mobile phone as you normally do Once the call has been set up the sound will be transmitted to your inductive receiver e g Sensa automatically 3 Repeat call press K1 button two times you can repeat latest call Answering and ending calls When the inductive loop is powered on and there is an incoming call you will hear a musical beep and also the indicator will change to quick flashing mode when the inductive loop is in stand by the indicator will be in slow flashing mode 1 When the inductive loop rings press K1 button to answer 2 Adjust the inductive loop volume by pressing the K2 button discontinuously 3 End calls by pressing K1 4 When the inductive loop is powered off and a call is coming press K1 button to activate the loopset and then again to answer call Note Due to different design of some mobile phones an auto disconnect may happen even when the inductive loop is powered on In that case the inductive loop won t ring when there is an incoming call Press K1 button for 1 sec to reconnect the inductive with mobile phone for an incoming call Low Battery Double flashing indicator indicates that Bluetooth inductive loopset is running on low battery Please charge the Bluetooth inductiv
4. e loop as soon as possible Important Information Trouble Shooting 1 The red LED indicator is double flashing It indicates that the Bluetooth inductive loop is running low on battery Charge the Bluetooth inductive loop as soon as possible 2 The Bluetooth inductive loop cannot be activated after being charged for 20 minutes To activate the Bluetooth inductive loop it needs to charge the battery at least for 40 minutes It is highly recommended to fully charge the battery before use 3 No indication of charging is shown For the Bluetooth inductive loop battery that is empty or has not been used for a long time it may take some minutes for the Bluetooth inductive loop indicator to show charging status with a steady red light 4 No sound can be heard or quiet sound is heard in the earpiece Make sure that the two devices have been paired loop and mobile phone Make sure that the Bluetooth inductive loop is turned on and the sound is not turned down to adjust the sound K2 button on the side of the cover Make sure that the two paired devices are within 10 meters range loop and mobile phone Make sure that your mobile phone is within strong signal place Some Bluetooth mobile phones can support only one Bluetooth device Disconnection may happen when there is more than one Bluetooth device paired with your mobile phone Why is there noise in the earpiece while using with Bluetooth loop Bluetooth inductive loop call quality can be
5. h inductive loop 2 The Bluetooth Pair mode will continue about 2 minutes the headset will automatically power off if pairing can t be completed within the time So you must repeat steps 1 to 3 until Pairing succeeds Wearing the Bluetooth inductive loop The Body of the Bluetooth inductive loop should be placed freely on Your chest while loop should be located around the base of Your neck To ensure that the device is completely invisible for others You can put it under Your clothes Ordinary clothes have no harmful influence on the connection and sound quality Wired microphone is destined for wearing it directly on the surface of Your skin It s very comfortable to wear it on the wrist neck etc To attach the microphone to your skin use medical plaster The movable microphone can be also attached to Your clothes e g under the lapel collar and cuff Notes Do not close the inductive loop to the inductive receivers such as SENSA earpiece for less than 20cm It may cause serious damage of the inductive receiver and it may also harm hearing while the receiver is inside the ear canal Making and Answering Ending Calls Once the Inductive loop is successfully paired with your phone you can use the inductive loopset to make and receive calls The inductive loop can be used with voice dialing if your phone supports this function For detailed operation on voice control please refer to the user manual of your mobile phone Making calls
6. s until the indicator of the Bluetooth inductive loopset start flashing Step 2 Initiate pairing process on Your Bluetooth mobile phone to pair the Bluetooth inductive loop Details are in Your mobile phone manual After research complete You will find a new device named Oval in the list of the Bluetooth Step 3 You will be required to input Pin code Please input the Bluetooth inductive loop Pin code 0000 and carry out Pairing Process Note 0000 is a default Pin code pre stored in the Bluetooth inductive loop Turning the Bluetooth inductive loop On or Off 1 To turn the Bluetooth inductive loop on press and hold K1 button and will hear high tone and the green indicator of the Bluetooth inductive loop will flash three times The Bluetooth inductive loop is now turned on Turning the loopset for the first time will switch it into pairing mode 2 To turn the Bluetooth inductive loop off press K1 button for about 3 seconds you will hear long lasting tone The green indicator of the Bluetooth inductive loopset will be going on for 3 seconds and then the Bluetooth inductive loop will turn off 3 When the green indicator double flashes it means the Bluetooth inductive loop energy is not enough Notes 1 If the Bluetooth inductive loop is not in pairing mode Your mobile phone won t find the Bluetooth inductive loop Please set the Bluetooth inductive loopset into pairing mode before letting your Mobile Phone research for the Bluetoot
7. tery capacity may be reduced if operation in a cold environment The Bluetooth inductive loop has to be recharged every two months when it is not in use during a long time
Download Pdf Manuals
Related Search