Instruction manual
Contents
1. 2004 A12 2006 A2 2006 A13 2008 A14 2010 A15 2011 EN 62233 2008 e EN55014 1 2006 A1 2009 A2 2011 e EN 55014 2 1997 A1 2001 A2 2008 e EN 61000 3 2 2006 A1 2009 A2 2009 e EN 61000 3 3 2008 e EN 61000 3 11 2000 e EN ISO 3744 Measured sound power level dB A 101 Guaranteed sound power level dB A K 3 0 Aurelio de Michele Product Manager 17 07 2013 i F OF OA AAA y iF ia2. In case you fall or collide with the machine please check the main machine and parts for any damages or cracks 2 7 When stepping backwards be cautious about any obstacles beneath your feet or behind you to avoid falling 28 When using the machine if you notice the machine running in an unstable state or hear abnormal sound from the engine please stop the machine and disconnect the power immediately and contact your original distributor 29 When operating the machine while taking care of your safety you should also be cautious to avoid any harm to other people Call nearby passengers attention to avoid potential personal injury 30 Use for snow removal only 31 Please do not take back and store the machine while it is still connected to the power source It may cause damage and injury 32 Keep the plug clear from water 33 To prevent electric shock use only with an extension cord suitable for outdoor use Does not apply to battery operated Snow Thrower 34 Keep hands away from moving parts Shut off engine before unclogging discharge chute 35 Dress properly Do not wear loose clothing or jewellery They can be caught in moving parts Rubber gloves and non skid footwear are recommended when working outdoors The user should wear a protective helmet to avoid your hair from getting in contact with any revolving part of the machine 36 Keep children and visitors away Visitors should wear safety glasses and be kept a safe dis
3. A Upper chute crank C Screw B Lower chute crank c NG a E PA DOYA D F Figure 15 A Upper chute crank D Wrench B Lower chute crank E Nut C Screwdriver F Screw 5 Slide the lower crank into the chute base hole Slide into chute base hole 6 Remove the washer and nut from the eye bolt with rubber grommet found on the upper chute crank Position the chute crank so that the eye bole with rubber grommet inserts into the center hole of the middle frame Secure with washer and nut Figure 16 A Eye bolt with rubber grommet C Middle frame B Upper chute crank D Center hole A Upper chute crank B Eye bolt with rubber gromment C Middle frame D Washer A gems E Spring washer 4 AL B F Wing nut A E O f f Figure 17 CQ gt Coa of V Operation Note Before using the machine please make sure the power source you will use is in accordance with the specifications shown in this manual Before inserting the plug into the socket make sure the machine s roll shaft and the snow thrower s rubber plates are all fixed firmly with screws and the rubber plates are facing to the correct direction Perform a test run to ensure that the rotor turns feeely Securing the extension cord 1 For safe and efficient use of your snow thrower use only a CE rated extension cord recommended for outdoor use 2 To prevent the extension cord from disconnecting during use tie th
4. Figure 5 A Joint fixing knob 3 Connect the upper frame with the middle frame in the same way as described in step 2 Use the joint fixing T bolts washers and knobs to secure the connection on both sides A Upper frame B Middle frame Figure 6 Figure 7 Joint fixing T bolt B Washer A aw far L6 Ny a A Figure 8 A Joint fixing knob B Washer 4 Locate the cable clips in the parts bag Secure the power cord to the frame of the unit by clipping them onto the frame at evenly spaced intervals Figure 9 A Cable clip Discharge Chute and Chute Crank Assembly 1 Lift the chute deflector so that it snaps and locks securely onto the discharge chute Discharge chute Chute deflector Chute deflector knob 2 Raise or lower the chute deflector to the desired height of the snow stream and tighten the chute deflector Knobs Note Do not overtighten the chute deflector Knobs Chute deflector knob 3 Locate the low and upper chute crank in the parts bag Loosen the screw and nut located on the upper chute crank with screwdriver and wrench Note You may be able to unfasten the screw and nut by hand Figure 13 Upper chute crank C Screw B Eye bolt with rubber grommet D Nut 4 Slide the upper chute into the lower chute crank aligning the screw holes Tighten the screw into the aligning holes using a screwdriver Fasten the unit with wrench Figure 14
5. LEA goeien LE60200 50 022459 IMPORTANT Read and understand this manual before assembling or operating this Electric Snowthrower Improper use of Snowthrower can cause injury Keep this manual for future reference Contents l Parts List Il Technical Data lIl Safety Instructions IV Getting Started V Operation Vl Maintenance and storage l Parts List 1 Switch button 2 Switch trigger 3 Switch housing 4 Upper frame 5 Upper chute crank 6 Fixing knob 19 Plate 7 Plug 8 Middle frame 9 Lower chute crank 10 Chute deflector 11 Discharge chute 12 Lower frame 13 Top cover 1 14 Top cover 2 15 Wheels 16 Side cover 17 Scraper 18 Auger Il Technical Data LE60200 50 QT3121 Rated Voltage 230V 50Hz Input Power 2000W Plowing Capacity Max 200 m h Rotation Speed 3000rpm Plow depth and width Approx 25cm 50cm Max Spraying Distance 9m Weight 16 kg NOISE AND VIBRATION DATA LPA 87dB A LWA 101dB A Vibration 7M S lll Safety Instructions GENERAL SAFETY INSTRUCTIONS Warning Read all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury The term power tool in all of the warnings listed below refers to your mains operated corded power tool or battery operated cordless power tool SAVE THESE INSTRUCTIONS 1 WORK AREA a Keep work area clean and well lit Cluttered and
6. damage or injuries 12 Special care should be drawn to the following issues when using this machine operation methods procedures surroundings and environment states etc 13 When using this machine the user should be cautious about the nearby status or changes The user should constantly observe the position and movement of other people nearby window vehicles obstacles etc Exercise caution to find any small piece of rocks or other articles in the snow to avoid them from flying out and causing personal injury 14 In case of following conditions please turn off the machine and pull out the power plug When not used being repaired replaced of some parts being cleaned and checked as well as any other conditions in which dangerous factors exist If cord is damaged in manner while plugged in pull extension cord from wall receptacle 15 Never carry snow thrower by cord yank it to disconnect from receptacle 16 Do not use hands to unclog chute Stop motor before removing Debris Do not walk in front of running machine Do not direct discharge at bystander 17 When using the machine the user must keep correct postures Heels should be placed firmly on the ground while the hands hold the handles firmly 18 Before using the machine the user should have a careful inspection of the main machine Carefully check the different parts of the machine before starting solving any problem immediately If you find any abnormal condition please d
7. dark areas invite accidents b Do not operate power tools in explosive atmosphere such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes c Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 2 ELECTRICAL SAFETY a Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock b Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded c Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock d Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock 3 PERSONAL SAFETY a Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medicat
8. e extension cord into a loose knot on the top right side of middle frame before connecting the plug in the switch cord socket of the snow thrower Powering on and off Keep the plug into the outlet To power on press the button B and trigger C or A at the same time power is on then you can release the button B the machine started Release the trigger A or C power is off A Switch trigger B Switch button C Switch trigger To power off Release the trigger A or C Moving the Machine and Plowing the Snow Foreign objects such as rocks broken glass nails wire or string can be picked up and thrown by the snow thrower causing serious personal injury Remove all foreign objects from the area to be plowed before operating the snow thrower 1 Keep the area of operation free of foreign objects that can become thrown by the rotor blades Perform a thorough inspection of the area since some objects may be hidden from view by surrounding snow If the snow thrower hits an obstruction or picks up a foreign object during use stop the snow thrower disconnect the extension cord remove the obstruction and inspect the unit for damage Repair or replace any damaged part before restarting and operating the unit 2 Keep children pets and bystanders away from the area of operation Be aware that the normal noise of the machine when turned on may make it difficult for you to hear approaching people 3 When moving the sno
9. ion 3 Replace the large belt by following instructions in reverse order Storage 1 Allow the engine to cool and clean the snow thrower before storing or transporting Be sure to secure the unit while transporting 2 Disconnect the extension cord from the snow thrower 3 Inspect the extension cord closely for signs of wear or damage Replace it if it is worn or damaged 4 Inspect the snow thrower carefully for worn loose or damaged parts Check connections and screws and tighten if necessary 5 Store the unit along with the disconnected extension cord in a locked dry place out of the reach of children to prevent unauthorized use or damage Cover loosely with a tarp for added protection DECLARATION OF CONFORMITY CE Who has signed below Aurelio de Michele authorised by Dunsch Europe SRL with the following address Via dell Artigianato n 10 I 29010 GRAGNANO TREBBIENSE ITALY declares that the products brand LEA model LE60200 50 QT3121 with serial number of year 2013 on the year of manufacture is clearly indicated on the tool identification plate followed the serial number comply with all the requirements stated by the Directive 2006 42 EC of the European Parliament and of the Council of 17 May 2006 on machinery These tools also comply with the requirements of the following community directives Directive 2000 14 EC Directive 2004 108 EC Directive 2006 95 EC ISO DIS 8437 2008 e EN 60335 1 2002 A11 2004 A1
10. ion Amoment of inattention while operating power tools may result in serious personal injury b Use safety equipment Always wear eye protection Safety equipment such as a dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries c Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents d Remove any adjusting key or wrench before turning the tool on Awrench or a key that is left attached to a rotating part of the power tool may result in personal injury e Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations f Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts g If devices are provided for the connection of dust extraction and collection facilities ensure that these are connected and properly used Use of these devices can reduce dust related hazards 4 POWER TOOLS USE AND CARE a Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate from which it was designed b Do not use the power tool if the switch does
11. l hurt you bs Keep foot way from the moving parts of the snow thrower The rotating parts will hurt you IV GETTING STARTED 1 Remove the snow thrower and all other items from box 2 Check all items for shipping damage If you find any damage or any parts are missing promptly inform the dealer where you bought the Snow Thrower The Snow Thrower comes with below accessories packed in part bag Cable clip 2pcs Fixing knob M4 50 4pcs Bolt 4pcs Screw M4 16 1pc Nut M4 1pc Note Upper chute crank and lower chute crank are packed as two parts in the box The snow Thrower is to be assembled before Operation To assemble the snow thrower follow the instructions below Upper Middle and Lower Frame Assembly 1 Loosen and remove the four sets of joint fixing T bolts washers and joint fixing knobs to separate the upper frame from the lower frame A Upper frame B lliddle franie C Lower frame Figure 2 2 Hold the middle frame so that the screw holes align with the holes on the lower frame Insert the T bolt with washer into the holes on each side and use the joint fixing knobs to secure the connection on both sides The joint fixing bolts and washers should be inserted inside the frame of the unit so that the joint fixing knobs are fastened to the outside of the frame Note Do not over tighten the knobs Figure 3 A Middle frame B Lower frame Figure 4 A Joint fixing T bolt CO
12. not turn it on and off Any power tool that can not be controlled with the switch is dangerous and must be repaired c Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally d Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other conditions that may affect the power tools operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control g Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation 5 SERVICE a Have your power tools serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the powe
13. on t use the machine before repairing 19 If you find the main power cable or the extension cable damaged please pull out the plug from the socket and disconnect the power immediately Repair the cable for replace it if necessary When adding the lubricant or replacing any parts you must strictly observe the instructions and procedures described in this User Manual 20 Special care should be paid to any rubber parts since these parts may increase the engine load and decrease its mechanical power if damaged 21 When you examine service clean the machine or replace parts you must turn off the power switch and disconnect the power cable Any such operation should be performed after revolving part inside the machine stops completely 22 The first time you use the machine or after replacing some parts you should perform a test running and ensure no abnormal conditions exist to avoid any potential damages or incidents 23 Do not move or transport the machine when the plug is connected into the power socket and the switch is turned on 24 When using the machine you must respect local laws and regulations regarding noise control and environment protection To avoid any noise disturbance to other people you should carefully decide operation time and consider the surrounding conditions 25 When the machine is running be cautious to prevent your hands feet or head from moving near to the revolving part or the snow exit of the machine 26
14. r tools in maintained ADDITIONAL SAFETY RULES FOR SNOW THROWER 1 Know your tool Read owner s manual carefully Learn its applications and limitations as well as the specific potential hazards related to this tool 2 Do not operate this unit when tired ill or under the influence of alcohol drugs or medication 3 All guards and safety attachments must be installed properly before using the unit 4 Inspect the unit before use Ensure the parts are installed correctly and secure 5 Clear the area to be plowed before each use Remove all objects such as rocks broken glass nails wire or string which can be thrown or become entangled in this tool 6 Keep the area of operation clear of all persons particularly children and pets 7 Avoid dangerous environment Don t use power tools in damp or wet locations or expose to rain Keep work area well lit 8 Keep work area clean Cluttered areas and benches invite accidents 9 Be cautious to avoid electric shock When using the machine keep your body away from different ground terminal of power e g upper and lower water pipes outer frame of heating equipment microwave oven or in a place that is locked 10 The machine should be stored carefully and safely in a dry environment when not used far from the reach of children or in a place that is locked 11 Please do not use the machine in any purposes other than it is designed for otherwise it may cause mechanical defaults or serious
15. t 2 Install the new rubber plate so that the coarse side faces inward and the smooth side faces outward 3 Insert the bolt with the small flat washer into the corresponding holes on each end of the rubber plate Use the large flat washer and locknut to secure the bolt on each end Install the other rubber plates in the same way Figure 25 A Rubber plate E Auger B Rivet F Large flat washer C Small flat washer G Locknut D Bolt Figure 26 Rubber plate E Auger B Rivet F Large flat washer C Small flat washer G Locknut D Bolt Figure 27 A Rubber plate D Bolt B Rivet E Auger C Small flat washer Replacing the Scraper The scraper is located at the base of the snow thrower beneath the rotor housing Figure 28 Scraper B Screw 1 Detach the worn scraper from the snow thrower by removing the 3 screws that hold it in place Figure 29 Scraper removal 2 Install the new scraper and fasten it securely to the snow thrower with 3 screws Figure 30 Scraper C Screwdriver B Screw Replacing the Belt Note Determine the left and right hand sides of the snow thrower by standing behind the unit in the normal operating position 1 Remove the screws from the left panel of the snow thrower 2 Lift the belt tension and roll the large belt off the big pulley Figure 31 A Big pulley C Large belt B Belt tens
16. tance from work area Do not let visitors contact too or extension cord 37 Use right tool Don t force small tool or attachment to do the job of a heavy duty tool Don t use tool for purpose not intended 38 Do not force unit It will do the job better and with less likelihood of injury at a rate for which it was designed 39 Always wear safety glasses Everyday eyeglasses have only impact resistance lenses They are not safety glasses 40 Keep hands face and feet at a distance from all moving parts Do not touch or try to stop the machine when they are rotating Do not operate without guards in place Symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use Double insulated for additional protection C c Conforms to relevant safety standards Read the instruction manual A The following warning symbols are to remind you of the safety precautions you should take when operating the snow thrower x s ii Always keep the children or pets away from the working area F Always keep away from the working area The throwing snow may hurt you bi NF ma Waste electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your local authority or retailer for recycling advice amp Keep hands away from the moving parts of the snow thrower The rotating R parts wil
17. the operator causing serious boldly injury Do not advance the chute deflector too far forward causing an opening to appear between the deflector and discharge chute Do not overtighten the knobs on the chute deflector VI Maintenance warnina Make sure to turn off the switch and disconnect the extension cord before performing any maintenance task on your snow thrower Lifetime Lubrication Lubrication is not necessary and may damage the unit The snow thrower is lubricated for lifetime use at the factory before shipment General Maintenance Tips 1 Do not attempt to repair the machine unless you have the proper tools and instructions for disassembly and repair of the machine 2 Check the shear bolts and other bolts at frequent intervals for proper tightness to ensure that the equipment is in safe working condition 3 After each snow removal session run the snow thrower for a few minutes to prevent the collector impeller from freezing Shut off the motor wait for all revolving parts to stop completely and wipe residual ice and snow off the unit Rotate the chute crank several times to remove any excess snow Replacing the Rubber Plates Note When replacing worn rubber plates pay close attention to carefully distinguish between the coarse and smooth side of the plates Place the coarse side inside and the smooth side outside 1 Detach the worn rubber plate by removing the two sets of nuts bolts and washers used to secure i
18. w thrower use the wheels on one side as the pivot point Slightly tilt the snow thrower on this pivot point to move it forward or backward 4 Start your clearing path near the electrical outlet and work outward throwing snow in a back and forth motion To clear in the opposite direction step over the cord and pivot the snow thrower on its wheels Make sure to overlap clearing paths 5 Note wind direction If possible move in the same direction as the wind so that the snow is not thrown against the wind and thus back into your face and on the just cleared path 6 While moving the snow thrower do not drag the power cable violently or roughly The snow thrower should move within the range that the cable can reach 7 Do not push the snow thrower with excessive force You should push the machine gently and evenly in accordance with the unit s throw rate 8 Do not apply additional man made load to the engine since this may cause engine damage 9 Some parts of the snow thrower may freeze under extreme temperature conditions Do not attempt to operate the snow thrower with frozen parts If the parts freeze while the snow thrower is in use stop the snow thrower unplug the extension cord and inspect for frozen parts Free all parts before restarting or operating the snow thrower Never force controls that have frozen 10 Working on pebbles gravel or unpaved surfaces To avoid throwing loose surface material along with the snow push do
19. wn on the handle to raise the scraper at the base of the unit above the pebbles or gravel Changing Snow Exit Direction A WARNING Never direct the snow discharge chute at the operator at bystanders at vehicles or at nearby windows The discharged snow and foreign objects accidentally picked up by the snow thrower can cause serious damage and personal injury Always orient the discharge chute in the opposite direction from where you bystanders surrounding vehicles or windows are located 1 The discharge chute can be adjusted 180 degrees by rotating the chute crank Rotate the chute control crank clockwise to move the discharge chute to the left counterclockwise to move the chute to the right Figure 22 A Chute crank B Discharge chute Figure 23 A Chute crank B Discharge chute 2 The chute deflector on the top of the discharge chute controls the height of the snow stream Loosen both chute deflector knobs to raise or lower the deflector to the desired height of snow you wish to throw Tighten the knobs to secure the deflector Note Do not overtighten the chute deflector Knobs Figure 24 A Discharge chute CG Chute deflector B Chute deflector knob A WARNING Make sure that the chute deflector snaps and locks completely onto the discharge chute An opening between the discharge chute and the chute deflector may allow foreign objects to be picked up by the snow thrower and thrown in the direction of
Download Pdf Manuals
Related Search