English-eTotem-NOVA-User manual
Contents
1. PP series User Manual 6 Terminal Server 6 1 Nebula TC Software Instruction Advertising display terminal is an unmanned multi media system After being connected with Nebula system terminals can realize information transmission with the system and the system can offer all kinds of services for terminals Terminals will periodically visit the server to receive and perform the control command terminals will download and broadcast the list do the listing and collect and feed back execution result as well as play log for operation platform to check Several tips shall be noted in order to make the system automatically start up and enter into Nebula terminal working state 1 There can only be one user name for operation system 2 There should not be password for operation system 3 The Windows7 system shall set the terminal executable permissions only for the administrator Advertising display terminal settings include three parts terminal information configuration display configuration and camera configuration Terminal information configuration is to set terminal registration communication rules and relative information to the server to ensure right authentication and normal communication in Nebula system Display configuration is to set mapping area and location of the display in IPC and program broadcasting configuration to make sure that terminal can play correctly and smoothly Camera configuration provides a means of2. 7 1 2 3 4 5 8 Maintenance Appendix A Technical Specification Appendix B Dimensions PP series User Manual 1 SAFETY This chapter contains important information to prevent personal injury and product damage when you install the display Read this chapter and keep it properly Ensure that you understand and follow all the safety instructions and warnings in this chapter before installing Personal Protection Warning Ensure that you understand and follow all the safety instructions warnings mentioned in this manual Warning Pay attention to electric shock Warning Wear a hard hat to reduce the risk of personal injury Warning Be aware of suspended loads Warning Mind your fingers while dealing with heavy loads Personnel of installation and maintenance The installation and maintenance of this product must be performed by authorized and qualified technical personnel only The manufacture does not take responsibility for the results caused by incorrect improper irresponsible and unsafe actions GND and Lightning protection Do not underestimate the safety protection of grounding plug socket If the supplied plug socket is defective replace the defective parts Ground the product correctly to avoid electric shock caused by large electricity leakage Disconnect the power in the time of lightning or provide other suitable lightning protection device Disconnect the power plug when the product is no
3. Wa dp Status TI Config 3 Schedule Impor t PP series User Manual 6 5 Camera Settings On site visible monitoring solution would be provided which is involved with screenshots of the multimedia player as well as timing photo taking of the camera Through the operation platform the pictures which are uploaded to the server could be seen and downloaded The maintenance personnel can know the situation of the screen via screenshots Besides the condition of surroundings and audience can be detected through the camera photo taking process In the camera configuration bar picture capturing size and position could be set via sub dialogue camera shot Remember to tick and select camera shot A Nebula Terminal Control Maximum number of local pictures when network failure Camera Shot Camera Type Camera Information op Upload Status 1 ovr Config amp 5 Schedule Import 24 PP series User Manual 6 6 Basic Information of the Terminal Basic information of the terminal mainly indicates the current status of the terminal For instance the MAC address equip connect status read equip status result interaction interval last interaction time and result See the picture below a Hebula Terminal Control MAC Address O0 08 2F 3T 35 3F Current Schedule Name schl sch Screen Config Equip Connect Information Camera Config EE 1 Equip Connect Status Connected QE term
4. Hi TAFC IAJEDIEEDO P Seen Tas Lila Tp C gil 1 Canin Gere Mode Saghirazi First Bre 3 Lev Grey Ce Orest Conia n ae Dsrrde Tae Wai Ste ce La Hina ail FHT 58 px uii Fiird AA tih Fim Hanh Madii 2 irie Pero are Bain ia i mH oe cod dias 48 Retest Arj S Guha Clark club Pri Fi rdcin Time Lime CTT FA Image 5 6 Scan board configuration interface 20 PP series User Manual 5 Screen connection According to the data cabling of your LED Display fill in the actual value of columns and rows Choose right ports and fill right scan board size as below Select correct direction of signal cable cascading Image 5 7 shows the front view of screen see from image4 6 S for the first tile and E for the last one Choose Send to HW and Save CEPIT ip T Hn 1 E Sinding Board Scan Board Seam Configuration era morakn Typ KA Sipe Soar eee Dr Sailr d Ser Ce Comylez Ey aen Bast Infsrsatisn E 0 T ip Virtual Boda Faal Firal Dparhha Fari Eran Jour dl 5 Zenlimp Poud Indes Calne F sj sd sl El wl ml wl w KA AA ent Sean Darl Fidih Hi Haight 4 Image 5 7 Screen connection interface 21
5. i User U System S Device E Control C Plug in Tool P Setting Language L Information Help H X e 6 Q Screen Config Brightness Cabinet t Calibration Display Control Monitor Function Card Global Control Connect Info Current Serial Port COMS Device Type Controller System Device Count Monitor Info Status Temperature Humi di ty Server Status 1 0 Image 3 8 NovaLCT Mars control software interface Note For more information about installation and instruction of control software consult Nova LED Display Control System Mars 3 User Manual 13 PP series User Manual 3 8 Power Distribution System The power distribution system of the PP series has air switch leakage protection switch fuses AC contactors The system has protection of overvoltage overcurrent undervoltage Short circuit open circuit and leakage The main switches in the power distribution cabinet are made of the Schneider devices and all other accessories and wires has CCC certification kE SSR j iu n KA ys M ul 0d a eU 1 po p x Power supply for 0 Multi funtion card Power supply for IPC 8 Speaker Positive pole terminal Negative pole terminal Image 3 9 PP series power supply system diagram Selecting and layout of the power line LED display is supplied with AC220V power with good grounding and reguires that the grid voltage f
6. 4 Resolutions supported 1024 1200 1280 1024 16007848 1920 712 2048 640 Caution A multifunction card is required for outputting the audio Data Interface A 3 2V 5 0V input socket Data interface B 017 USB interface DVI input interface Image 3 6 MSD300 transmitter card 11 PP series User Manual 3 6 3 MFN300 Multifunctional Card 1 RJ45 ports for connection with receiver cards 2 serial ports for connection with the control computer 3 Support 8 power supply control 4 Support light sensors 5 Support temperature and humidity monitoring 6 Audio input interface Caution For audio output the multifunctional card needs to be connected between receiver cards or at the end of the cascading chain 3 2V 5 0V input socket Rs232 Serial port RJ45 connect to receiver card Image 3 7 MFN300 multifunctional card 12 PP series User Manual Peer gp DBDB p 3 7 LED System Control Software NovaLCT Mars control software is used to configure and control LED display through PC in Graphics User Interface fua kari Eh H fom Tres 8 dom ira Bag 757 iim bain Ham ien erin mind Dris foes Am Fede Ba eR Patika Tuas i aga i iif H kidi fimi hiur faria Bai dade E e im ed aite E EDO e P B ER n E luna eum It I up
7. Begin Download Time 2012 12 21 13 01 5T Finish Download Time 2012 12 21 13 02 07 5 ly seren a File Hame List Hame Status Retry Time Download Progress Bit Camera Contig P Terminar Info am f e 4 Update Info or Upload Status Lu DYI Config schedule Import Download Status 1 6 9 Log Upload Status When the platform commands the terminal to upload play log the upload progress and result would be fully demonstrated See the following picture Nebula Terminal Control fe a l tersine Config Begin Upload Time Finish Upload Tima J 1 Screen Status Upload Progress Fila Path Screen Config 5 ar Camera Config OQ Terminal Tuto 9 Update Info v Download Status Cam Config uet 26 Clear PP series User Manual 7 Trouble Shooting 7 1 Software Trouble Unable to open Noval CT Replace LCT software Software problem ay Computer is not 1 Computer is not installed installed with NET wit Framework h NET Framework 2 Already installed but software may be damaged The RS 232 System notice Install Microsoft NET NovaLCT exe error Framework 2 0 Check the RS 232 dl communication IS not connection and T comimunieston connected or could y not get through connection fails 1 Nova LCT version may be L
8. controller He start the controller o WU Divider is working when RUN lamp blinks 2 times per second The lamp blinking 2 seconds per time means no data is output from controller or the fiber is broken Check the power of the No power for the divider divider Check data input from upper receiver card RUN lamp blinks 2 times per second If the data in is ok but problem still exists replace the receiver card Check RUN status on There is no data the divider If it blinks 2 from the controller seconds once it means or the fiber cable no data from the fiber is not well cable connected Hardware problem Poor Cat5 connection or output data problem of the upper receiver card If there is no data input from the cat5 check the cat5 connection or no data output from the upper receiver card Check the hub card connection with the scan card or the ribbon cable connection Connection between the hub card problem or and module If hardware problem connection is no problem replace the hub card PP series User Manual 7 2 System Hardware Trouble Problem type Problem description Controller Black screen Divider Divider driving area is black Heceiver card problem causes black display on single tile Receiver card One row of the module in the tile is black or messed up 28 PP series User Manual 7 3 Module Problems Problem Problem Phenomenon amp Besson Analysis type description
9. image 5 1 to open Nova LCT Mars control software and the computer will enter to the interface as image 5 2 Local system info shows the real system connection information when it shows Control System 1 it means the USB serial port connection is ready for communication between PC and controller If not it shows Control System 0 for the connection is not good with no communication If there is no image on LED screen green indicator of sending card not flicking please check DVI cable from graphic card to sending card then check multi display mode from control computer Keep display mode under duplicate mode 0 E HovaLCT Mar Image 5 1 E rs uiu GANDO Mai TEI 113 aad LI Lari gS snauLi mini f regam Dusplawiccen Monier l uecti n Dare Lal teesenm rag Lamtrsl Ce C mz p Mundo mo No Screen click here to config Berem Berar rT Image 5 2 18 PP series User Manual Eap 3 3 3X 2 User Login User login This menu is for user to login It is necessary for the configuration of the LED screen Click User Advanced Log in enter password 666 or admin O 8 0 2 8 37 System Tools Plug in Tool P Userlh LanguagefLangifL HelpiH a xX Brightness Display Cantral Monitor Function Card Local System Info 8 User Login Control Svstem View Detail Monitor Info Server Status Server Yersion 2 0 I
10. 0269 SHENZHEN LIANTRONICS CO LTD Headquarters ADD Liantonics Budding No 1 of Urian 3d Road Section 48 Bcoon District Shenghen City PRC Tel 845 755 2397 44688 Postcode 518101 Alter service 84 755 29 46683 27745557 E MAIL oversectitiononics com service com
11. CT communication Replace LCT changed confirm that you is not stable use the right version Set values of R G B brightness on the all controllers as the 1 Brightness values are not the same 2 Data is not saved Controller s R G B brightness values are not the same same successfully after setting 1 Calibration mode is not On 2 All the calibration modes are On but not successfully saved after setting 1 Brightness adjusting modes are not set as the same 2 The setting is not saved successfully Nova LCT The calibration mode The brightness is of controllers did not different before and set to On after calibration display brightness is Brightness adjusting not uniform Change the brightness modes are different adjusting mode between different controllers Check Gamma value of different controllers and resend the database If brightness adjusting is in auto mode and Brightness sensor controlled by sensor action need to wait new update needs to for 30 seconds wait for 30 seconds Gamma values are varied for different controllers shows wrong status LCT software card is black column setting in LCT LCT is wrong The whole display is schedule setting is wrong tudio black Media source is lost source or stopped No HDMI signal output from the graphics card in PC Check the power of the No power for the Cem No HDMI signal to the controller controller
12. Solution l The lamp is dead or LED lamp Blind lamps Replace the module soldering is not good kha najaza The driving IC resistor is LED pixel p Replace the module bad soldered or out of black or loses color Nork One or several Check the ribbon whole LED modules cable and power Cable is not connected LED module in the same row are cable connection on or not well connected black or defective the module 7 4 Power Problems Problem Problem Phenomenon amp Xt Reason Analysis type description Solution Check power M Power to the tile is not The whole tile is connection with the Tile power well or the breaker is black tile and the breaker turned off in the tile The whole tile is Replace the The power supply mE Power supply black defective power feeding the receiver supply card is defective Several nearby Replace the The power supply Power supply module areas are defective power feeding the module area black supply is defective 7 5 Data Transfer Problems Problem Phenomenon amp Check the data T The whole column The connection is not connection between Cat 5 of the display is nm good or the cat5 is the divider and the black defective first scan card One or several Check the cat5 The connection is not Cat 5 tiles in column are connection between good or the cat5 is black the tiles defective ANING espana Check and correct up but the columns The connection order is Cat 5 i
13. UTASA FELA m qr Hie a Ty iau TEN LEE iL y gE TTT 1 QULDLUARE kamaa 01 UEDA 41 mi ni m PP series user manual menm This manual is only for operating instructions and does not serve as repairing service Changes Liantronics provides this manual as is without warranty of any kind either expressed or implied including but not limited to the implied warranties or merchantability and fitness for a particular purpose Liantronics may make improvements and or changes to the product s and or the program s described in this publication at any time without notice This publication could contain technical inaccuracies or typographical errors Changes are periodically made to the information in this publication these changes are incorporated in new editions of this publication Copyright All rights reserved The copyright of this manual is protected by the Copyright Law of the People s Republic of China and other intellectual property laws No part of this document may be copied reproduced distributed translated or used for commercial purposes It shall not otherwise be recorded transmitted or stored in a retrieval system without the prior written consent of Liantronics LIANTRONICS CO LTD Add Liantronics Building No 1 Liuxian 3rd Road Section 68 Baoan District Shenzhen China Postcode 518101 E mail oversea liantronics com service lcjh com Visit us at the web www lian
14. anual 3 6 Control system 3 6 1 LED Receiver Card The functions of the MRV300 receiver card are shown as below Power supply 3 3 5 0V Temperature monitoring standard feature Power supply voltage monitoring standard feature Working status monitoring standard feature 16 RGB data groups output it can be extended to 32 groups load capacity of single receiver card up to 256x128 eSupport pixel level brightness color calibration DC input socket Press this button to change test pattern DC input terminal m B o5 W B ee ee ROB OMNE 50 pins data interface A RJ45 interface A CYA Extension data interface RJ45 interface B Status monitor Interface Reserved interface 50 pins data interface B Image 3 5 MRV300 receiver card Off line Test The receiver card supports off line test Users can test each parts of the PP series without connecting with LED control system The test steps are as below 1 Make sure that the receiver cards are connected with each of the LED modules but not connected with CAT5 data cable 2 Turn on the LED screen the tiles show nothing Press the black switch on the receiver card seven times Then the display contents on the LED tile will be changed to Diagonal Grey Red Green Blue White and Black in order 10 PP series User Manual 3 6 2 MSD300 Transmitter Card 1 DVI interface for video input 2 USB interface for instruction communication 3 Audio input interface
15. e the Cat5 connection are not in right l wrong order order in the divider ld oA C VJ PP series User Manual 8 Maintenance Routine maintenance 1 Make sure the LED display is well ventilated dry and running in suitable temperature 2 Regularly check the internal cables inside the LED display are in stable connection the power Supplies are working well the ground wires are connected well and the lightning arrester is running well 3 Regularly wipe the dust on the surface of the LED tile with a soft cloth and keep the LED display surface clean to avoid brightness differences between clean and unclean LED tiles Cautions for use 1 Before power on the LED display start your computer first and then turn on the power of LED display 2 Before turn off the display system first turn off the power of LED display and then turn off the computer 3 When you are editing video playlist you had better to keep the LED display off 4 When failure appears first turn off the power of LED display then contact with service department of LIANTRONICS for technical support 30 PP series User Manual Appendix A Technical Specification PP series Pixel Pitch mm 2 4 122 diagonal 97 diagonal 1412mm L X3486mm H X120mm D 1112mm L X2758mm H X120mm D Display Size 1152mm L X2880mm H 952 32mm L X2261 76 H Resolution 384pixels L X960pixels H 384pixels L X912pixels H Weight 200Kg 190Kg Power Co
16. fter installing and cabling Be ensure all the devices and terminals are covered before turning on the power e Do not touch the terminals when power is on Clean and screw the terminals when power is off Moving or transporting product Do not hit the corners of LED tiles when installing or dismantling LED tiles Be careful when moving or transporting the product to prevent any damage LED tiles can not be transported in containers other than LIANTRONICS flight cases or packaging Even the use of LIANTRONICS packaging does not guarantee the LED tiles against damage due to excessive force of impacts All warranty claimed regarding damaged modules due to incorrect packing will be rendered invalid PP series User Manual 2 Installation requirements This chapter specifies the requirements for safety mechanism electricity and control software of PP series fA Warning This LED indoor product is designed only for indoor use Never install and use it in outdoor environment and keep it far away from direct sunlight dust and moisture 2 1 Mechanical Requirements Weight Warning Do not underestimate the weight of the PP series Be sure that the floor or truss installation on which the PP series has to be installed is capable of handling five 5 times the complete load of the display For floor mounting conclude the weight of any other load Horizontal surface For floor installation the floor on which PP series is installed mu
17. inal Info Last esd oratie 2013 3 15 11 14 34 Time Read Equip Status Update Info Rese Download Status System Interaction Information a 2013 3 15 11 14 48 2013 3 15 11 15 08 Upload Status l Last Interaction 7 Result DYI Config Succeed 1 l Next Interaction 2013 3 15 11 15 48 Time gt Schedule Import Interaction Interval BO seconds 6 7 Software Update Information This part maintains the current version of terminal and the update status of terminal version as shown in the following picture s Hebula Terminal Control yA Terminal Config Version Information Sersem Finis Software Ee 2 3 1210 3101 Hitra Version Version Before Update ue Camera Contig Update Information O tesina Info Current Update Status Update Into Last Update Time F Download Status Last Update Result Upload 5tatus Last Update Fail Reason Led IYI Config ki Schedule Import 6 8 Download Status of the List Terminal of the advertising display would download the list from the server and play it in accordance to its schedule After receiving the download list or schedule order the terminal would start to download and the whole progress together with the result can be clearly seen Nebula Terminal Control Online schedule download status schedule merge status Schedule Play Info gem l 1 Um Terminal Config
18. luctuation is less than 10 e Determine the diameter of the power cord according to the power of the display Unit mm the cross sectional area of the power cord The power supply has three wire system live neutral and earth or five wire system 3 live wires neutral and earth When the maximum power consumption of the LED large display is less than 10 KW generally use single phase three wire power supply and vice versa use the three phase five wire power supply 14 PP series User Manual 4 INSTALLaTION Installation Preparation Good viewing angle and good sight for the surroundings Favorable ventilation conditions eSafe and stable rating input voltage Suitable size firm and stable installation table board Rear maintenance space is more than 800mm from front to back Tools list for installation choice depends on the practical jobsite 1 Diagonal cutting plier 2 Combination plier 3 Screw drivers P v 4 Cut the wire Cut the steel wire rope Install tiles and power supply 4 L shape spanners 5 End wrench tool set 6 Adjustable wrench TA Tighten or loosen the screw Install tiles 7 Socket wrench 9 Rubber hammer TIE I ag w F Tar Lr 1 F Assemble the screen Measure voltage or current Adjust the gap between tiles Other tools for installation choice depends on the practical jobsite High brightness flashlight Safety rope Personal safety ve
19. mage 5 3 Login interface Select Config Screen directly to follow the next step XY NavalCcI NEars Vi 7 2 System iG Tools i ux Lozal Syaten Info Control System D Config Sereen Wodi Lor Tafe o Load Config File Server Stated Server Version 1 Image 5 4 Configuration interface 3 Go to sending board configuration As is Shown in image 5 5 select proper resolution for sending card and it should be close to graphic card Click Save to save parameter on HW 19 rap hikes oii ra yal utari 8x x d 024 cusi Slave Device Sie Sending Ei care indes PP series User Manual oe M PNE bl Scan Dord Screen 250 x i E cage as Bik i i ETE Coes bare Ng Ex redire cea nllinrr Get Hia sari ng ba arci Bl epi asy ree 255 45 ibi 1 ir DI Ferra eh Faki Hod Backup Sing Master Device Waster Furl majer 11 Board naar Image 5 5 Sending board configuration interface 4 Go to scan board configuration As is shown in image 5 6 select Load File down load rcfg file from delivered CD Click Send To HW and then the file will be send to each scan board receiving card Click Save and save all files in hardware when restart power files is no need to send again If tiles shows correct images before loading file skip this step and directly jump to step 5
20. nsumption 750W Average 2400W Max 600W Average 2000W Max Brightness 1200cd m Viewing Angle H 160 V 160 3000 1 21920Hz 60Hz Contrast Ratio Refresh Rate Frame Rate Color Temperature 2000KsTCs9300K Adjustable Brightness Adjustment Programmable Auto Manual Signal Processing 16bit Communication WiFi 3G CAT 5 Protection Grade IP32 Life Span 50 000hrs Power Supply Voltage 176 264V AC Operation Temperature 20 4500 Storage Temperature 40 60 Relative Humidity 10 95 Moisture proof dust proof flame retardant Protection Anti corrosion anti static anti seismic High temperature amp lightning protection Over current or short circuit protection Safety Over voltage or low voltage protection Temperature alarm Failure Monitoring Monitoring of temperature voltage working condition network failure 32 1000 PH3 8567 Cx X X UA UR UN UR e 000002 BOK A v SS Se x gt on LA x 1412 115 X Ux X Pt 0 Mete 0 e 120 Appendix B Dimensions PP series User Manual PP series User Manual T E 1125 2262 2158 p c LIANTRONICS 33 YA Lian Tronics souma QU CE RoHS FE call canines 400 885 0158 website www lc h com stock code 30
21. on spot and desktop monitor By camera configuration users can take photos and get screen shots of the desktop and send them to the server The platform can monitor these photos and shots to know system operation Status a f Core Server System switeh Main serve j d w E Rol r P i Firewali pa 2 Es 7 Speedup server 1 Switch se backup main Sener 3 1 E Speedup server z Operation platform Service platform Speedup server B Tanz group 1 Terminal group 2 Terminal group mnm 6 2 Install the Nebula TC Software After Nebula TC is installed terminal server will be automatically set as automatic operation after System startup If you need manual start click Nebula TC in the Start Menu shown as below AT m umm ee NENE D AA HovaHebulaTC fgg HovaN bulaTC 22 PP series User Manual 6 3 Main interface of Nebula TC i Hebula Terminal Control Language English len Log Config Operate Loz Save Time Q Last 3 days 0 Last 1 week Q Last Z weeks Play Log Save Time e Last week Q Last 2 weeks 0 Last 1 month Terminal Config Close Software on 71122 00 068 i Ladies Time Synchronization With Server MAC Address 00 OP 2P 3T 35 GF v E WAC 00 05 2F 37 95 38 Controller Type KO W200 System 9 M3 System Wpdate Screen Info Upda File Transfer Config Enable 53 Work Path Meal oooO make s
22. pplying the rack shall be installed near the equipment and be easily accessible or a readily accessible general disconnect device shall be incorporated in the fixed wiring Mounting parts The mounting parts are only used to install LED display Do not repair or copy Only use parts appointed by the manufacturer Contact LIANTRONICS if you want customized application Product care Inspect all installations on a routine basis to check security wear deformation corrosion or any other situation that reduces load carrying capability Increase inspection frequency for key parts Keep structural and mounting parts dry clean lubricated only if recommended coated properly and maintain complying with part design Defective parts must be removed or replaced at once Installation and wiring Install the display and connect cables following the manual instructions The installation and wiring must be secure Poor connection may lead to malfunction Do not step on power data cable or squeeze plug socket and power data cable Do not suspend any items on cables or the back of LED display Connect or disconnect the cables of data communication extension module or control unit after the power is off to prevent product damage or malfunction Risk of electric shock To avoid electric shock and damage do not dismantle the inside electrical parts e Hot plugging the cable is forbidden to prevent electric shock or circuit damage e Keep clean a
23. ry important 220V power outlet board 15 PP series User Manual Power connection Open the back shroud which is showed in the Image 4 1 Then you can find the Terminal blocks which is showed in the Image 4 2 s 5 Image 4 1 Back shroud of the PP series Image 4 2 Terminal blocks 16 PP series User Manual If your local power voltage is 220V you should connect the input power cable like Image4 3 The power voltage between L and N is 220V E c ET E n 7 A 1 AODAN P dal Image 4 3 Power connection of 220V power input If your local power voltage is 110V you should connect the input power cable like Image4 4 The power voltage between L1 and L2 is almost 190V Image 4 4 Power connection of 110V power input 17 PP series User Manual 5 START UP OF THE SYSTEM 5 1 Software Installation Before you run the software please make sure all connection are ready From PC to sending card from sending card to LED screen Put the LED system installation CD into CD ROM E Eral TBa 1 Double click fess to start LED control software installation 2 Follow the installation instruction until the installation procedure has finished 5 2 System Operation First power on the control system computer and switch on the power of LED display follow the procedures and instructions as below 1 Start Nova LCT control software Install Nova LCT control software double click the icon
24. st be horizontal Never install LED display on a slant surface Ballast Depending on the height of the display and the position of the LED display upon the foot beams somewhere between front and middle additional weight ballast will be required Consult professionals of LIANTRONICS to calculate the minimum ballast you require for safe installation of the LED display Installation ambience Environmental conditions humidity ventilation temperature etc Location Altitude etc Front clearances for optimal effect ensure that enough free space is supplied in front of the LED display and respect the minimum viewing distance Comply with local regulations regarding such installations PP series User Manual 2 2 Electrical Reguirements Power reguirements Electrical parameter Input voltage 220 15Yo According to the actual situation Average power 815W consumption Max power consumption 2450W Input power frequency 50 60Hz Max supply current 11 1A Input voltage 220 15 Output voltage 57 6VDC Output current 0 50A Input voltage 36VDC 76VDC Output voltage 5VDC Output current 0 30A AC DC Power supply electrical specification AC DC Power supply electrical specification Power cable standard Power system It is recommended to use power distribution system with a separate neutral and grounding conductor to avoid large current loops due to voltage differences in the neutral cond
25. star grade hotel book store pavilion conference center cinema bank office etc 3 2 System Components PP series series includes the following basic components e LED Display PP series e Control System control computer LED display controller distributor control system software PP series User Manual 3 3 System topological graph DVI cable CAT5 cable USB cable Signal cable Audio cable 6 Image 3 1 System topological graph of PP series PP series User Manual 3 4 LED Display Components LED module X 40 PCS Tempered Glass Metallic Painted Base E COLLECTION Image 3 2 The front face of PP series PP series User Manual Fan Access panel Image 3 3 The back face of PP series PP series User Manual 3 5 PP series Module PP series module includes die casting aluminum base frame PCBA etc At the back of the die casting aluminum base frame two copper screw holes are inlaid at each side to fix the module to the frame The black LED lamp array lies in front of PCBA LIANTRONICS adopts the black full color SMD LED lamps The use of black organic silicone and diffuser makes the black LED lamps darker to improve the contrast of the display significantly 5V input port Signal input socket 5V input port Signal input socket Die casting Aluminum base frame Back side of the LED module Front side of the LED module Image 3 4 The components of P3 module PP series User M
26. t used in a long period Ambience of installation and use e The ambient temperature for LED display max 40 C min 0 C e Ensure that the ventilation is good Do not jam or drop metal particles and cable pieces into ventilation opening Keep the ventilation surface clear without foreign matters like wrapping materials False actions may lead to poor ventilation and cause fire malfunction and error e Install LED display far away from radiator heater furnace and other equipments hindering ventilation and heat dissipation including but not limited to amplifier laser ultrasonic vibration devices flammable materials like curtains and other unsafe devices o O signal cables should be shielded to restrain the high frequency interference e LED display can not contact with any corrosive and abrasive matter Do not use LED display in moist ambience in ambience containing airborne contaminant dust oily fume corrosive gas and flammable gas and in ambience with vibration and shock e This LED indoor product is designed only for indoor use Never install and use it in outdoor environment and keep it far away from direct sunlight dust and moisture PP series User Manual ESD and LED LED components are ESD Electro static Discharge sensitive Do not touch LED components when the display is in operation or switched off Disconnect device When the appliance inlets of the individual tiles are not accessible the socket outlets su
27. tronics com PP series User Manual Software TroubIe cee cee wwa wwa waa waa wwa ce cee ser cee waa waa cae waa waa wwa ace waa wwa ae eae den een eae Hardware kaiouUble sw ore wwa wwa wwa wan rus wwa wwa nen ore awa wwa waa wwa nor waa ola 0 010161006 0 waz wwa aur num ust asd wwa mwa asa sas nnt nor nnt nne as wwa wwa me ee Sn Data Transfer ProbleMms we cee wwe wwa wwe wwa wwa wwa wwa ces wwa ces see ces cen wwa een ees wea ere eens Contents 1 Safety 2 Installation Reguirements 2 1 Mechanical Reguirements 2 2 Electrical Reguirements 3 System Introduction 3 1 Brief Introduction 3 2 System Components 3 3 System Topological Graph 3 4 LED Display Components 3 5 PP series Module 3 6 Control System 3 7 LED System Control Software 3 7 Power Distribution System 4 Installation 5 Start up of the System 5 1 Software Installation 5 2 System Operation 6 Trouble Shooting 6 1 Nebula Software Installation 6 2 Install The Nebula TC Software 6 3 Main Interface Of Nebula TC 6 4 Screen Configuration 6 5 Camera Setting 6 6 Basic Information Of The Terminal 6 7 Software Update Information sese ee HI sees ness ns 6 8 Download Status Of The List 6 9 Log Upload Status 7 Trouble Shooting T 7 7 7 Ta Power Problems
28. uctor Protect the electrical installation by switch circuit breaker over voltage protector defective grounding circuit breaker with proper rated power Install the display in accordance with local electrical installation standards In Europe comply with EN 60364 the standard for electrical installation of buildings In Germany comply with EN 60364 In America comply with National Electrical Code ANSI NFPA 70 Protective grounding To prevent against the risk of electric shock the installation should be properly grounded Defeating the purpose of grounding will expose you to the risk of electric shock PP series User Manual 3 System Introduction 3 1 Brief Introduction PP series of Liantronics the super size LED digital signage defines an electronic totem in digital times As the combination of hi tech and artistic creation it combines information transmission artistic expression and time connotation as one 3 1 1 Key Benefits e Super durable design e High grade protection with tempered glass e Hot backup system e Double backup power supply e Remote control and monitoring system e Centralized cluster network and remote control system to monitor and manage the status of LED screen Embedded with video monitor and ammeter e Access for WiFi 3G wireless and wired network e 4 1 sound track output 3 1 2 Applications PP seriess are perfect for airport subway station train station large shopping mall
29. ure the directory where Server Config Fa Sever Wi ittps 113 105 167 l User Identifier LTPH3 TEEMAA L Terminal Contig 7 1 3 TESS Info A waste Info w Download Status a Upload 5tatus DVI Config gt Schedule Import 6 4 Screen Configuration Fill in the blank according to the actual size and mapping area of the display in order to play the contents accurately and completely Ta Hebula Terminal Control screen Contig Sereen Count Screen Area Sereent Sereen Width 400 i aun cl a E Screen Height 30D Flay Config Enable Preventing Stuck Function for Video Note When enable the function if the video sereen stuck during playing the software can quickly stop the current video and switch to playing the next media Enable draw effects in vertical refresh synchronization Hote When enable the function the CFU utilization increases when picture effects is playing if the picture effects do not move or change in the vertical direction you may disable this function F Normal Video Rendering Bode Hate If the graphics card configuration of computer is low memory is less than 512M use this mode to reduce rezource utilization but transparent text would flash when overlay on the widen software uses advanced rendering mode by default Change this item after stop playing 23 mn 1 Terminal Confi aj LJ Er co Info
Download Pdf Manuals
Related Search