STM32 ST-LINK Utility release 3.1
Contents
1. Cor RN0078 yf i life augmented Release note STM32 ST LINK Utility release 3 1 About this release note Note This release note contains information about the latest version of the STM32 ST LINK Utility software e New features e Improvements e Program corrections e Known problems in current version The part number of STM32 ST LINK Utility software is STSW LINKOO4 New features July 2013 Version 3 1 e Added support of STM32F052 Entry level Cortex MO microcontrollers e Added support of STM32F401 series Cortex M4 e Added support of Connect to a device in low power mode option Version 3 0 e Added support of custom loader for external memory e Displayed Printf data sent via SWO e Added File compare to device memory feature in the CLI mode Version 2 5 e Added support of STM32F42x STM32F43x series Cortex M4 e Added support of drag and drop file opening e Added HotPlug Connect feature Connect to target without halt or reset e Added Context Menu and Edit Menu for Cut Copy Paste Delete operation on file and device memory e Added support of Memory LiveUpdate feature e Added support of Find data feature find in ASCII and HEX e Added support of Fill Memory feature fill with Byte Word or DoubleWord in file and device memory DoclD022036 Rev 8 1 7 www st com New features RN0078 2 7 Version 2 4 e Added support of STM32 F3 series Cortex M4 e Added support2. STM32 L1 ultralow power 32 bit microcontroller devices e Added support for STM32 F2 series microcontroller devices Version 1 2 e Added support of XL density devices 3 DocID022036 Rev 8 RN0078 Improvements Version 1 1 e Added support of Serial Wire Debug SWD interface Version 1 0 Initial release Improvements Version 3 1 e Enhancement of connection management Version 3 0 e Optimization of STM32 internal Flash memory programming and verification Version 2 5 e Enhancement of device memory modification from the memory grid Version 2 4 e Enhanced display of File Flash comparison Version 2 3 e Added Tooltip in the option bytes window e Enable Disable progress bar display in ST LINK CLI STM32 ST LINK Utility command line interface e Added support of programming at unaligned addresses e Different error codes return for each type of problem in CLI mode e Connect under reset option is now available in JTAG mode Version 2 2 e w8 and w32 CLI commands are able to program Flash memory e The Flash memory can be modified from the GUI even when it is not erased Version 2 1 e Automatic MCU voltage check with ST LINK V2 Version 2 0 e Faster switch between device memory display and file display e Connection management enhancement e Core status displayed in the MCU Core window 3 DocID022036 Rev 8 3 7 Improvements RN0078 AIT Version 1 3 e Flash mass
3. erase and Option bytes programming progress display Version 1 2 e Connection management enhancement Version 1 1 e Connection error management enhancement e Debug interface and connection status display Version 1 0 Initial release 3 DocID022036 Rev 8 RN0078 Program corrections Program corrections Version 3 1 e Fix loading Hex files with option bytes section Version 3 0 e BFB2 bit is forced to 1 on all STM32L15xxC devices when programming the option byte Version 2 5 None Version 2 4 e Fix STM32W108CC WRP granularity e Fix loading Hex file adjacent segments e Display RO register in Core window Version 2 3 e CLI return code issue fixed Version 2 2 e None Version 2 1 e Binary file save issue resolved with Windows7 Version 2 0 e Flash size is ignored for STM32 F2 series 32 bit microcontroller devices Version 1 3 None Version 1 2 None Version 1 1 e Corrected STM32 ST LINK Utility user manual pdf name format at start Menu Version 1 0 e Initial release J DoclD022036 Rev 8 5 7 Known problems in current version RN0078 Known problems in current version None Customer support Software released previously is documented internally and available upon request For more information see the STM32 ST LINK utility user manual UM0892 and visit our website at www st com Revision history Table 1 Document revision hist
4. PPLICATIONS SUCH AS LIFE SUPPORTING ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS B AERONAUTIC APPLICATIONS C AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS AND OR D AEROSPACE APPLICATIONS OR ENVIRONMENTS WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE THE PURCHASER SHALL USE PRODUCTS AT PURCHASER S SOLE RISK EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR AUTOMOTIVE AUTOMOTIVE SAFETY OR MEDICAL INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS PRODUCTS FORMALLY ESCC QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY Resale of ST products with provisions different from the statements and or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever any liability of ST ST and the ST logo are trademarks or registered trademarks of ST in various countries Information in this document supersedes and replaces all information previously supplied The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners 2013 STMicroelectronics All rights reserved STMicroelectronics group of companies Australia Belgium Brazil Canada China Czech Republic Finland F
5. ations or improvements to this document and the products and services described herein at any time without notice All ST products are sold pursuant to ST s terms and conditions of sale Purchasers are solely responsible for the choice selection and use of the ST products and services described herein and ST assumes no liability whatsoever relating to the choice selection or use of the ST products and services described herein No license express or implied by estoppel or otherwise to any intellectual property rights is granted under this document If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE IN A SAFETY CRITICAL A
6. of STM32L medium density plus Cortex M3 e Added support of STM32F050 Entry level Cortex MO microcontrollers e Comparison between two files Hex SREC or Bin files e Support of Reset after programming option Version 2 3 e Added support of STM32 F4 series Cortex M4 revision Z e Added support of STM32L Cortex M3 EEPROM data memory programming e Added support of STM32 FO series Entry level Cortex MO microcontrollers e Save file in Intel Hex and Motorola S record file format e Address TextBox replaced by a ComboBox with history saving Version 2 2 e Added support of STM32 F4 series of high performance microcontrollers with DSP and FPU instructions e Added support of STM32W 32 bit RF microcontrollers e Added support of Connect under reset option e Flash modification via GUI and CLI commands e Added support of hardware reset in CLI mode Version 2 1 e ST LINK V2 support e Added support for STM32 F2 series microcontroller programming modes e Connected MCU revision ID Display e ST LINK and ST LINK V2 firmware upgrade to V1J12S3 and V2J14S3 respectively Version 2 0 e Support of Intel Hex file and Motorola S record file format e Command line interface e Automatic Mode Programming and configuring STM32 devices in loop e Flash memory Blank Check e Compare the contents of the Flash memory with files e ST LINK firmware upgrade to V1J11S3 Version 1 3 e Added support for
7. ory Product Document Date ae P Changes Revision Revision 01 Aug 2011 2 1 1 Initial release Added Version 2 2 with support of STM32 F4 and STM32W series and attributes in New features and Improvements Added Table 1 Applicable tools 11 May 2012 2 3 3 Added Version 2 4 with support of STM32 FO series and attributes in Section New features and Section Improvements 18 Oct 2011 2 2 2 Updated Section New features Section Improvements and 29 May 2012 23 Section Known problems in current version Updated Section New features Section Improvements and OS OCEA a a E Section Program corrections Updated Section New features Section Improvements Section Manaos a and Section Known problems in current version Updated disclaimer 29 Apr 2013 3 0 7 Added information related to ST Link release 3 0 in Section New features Section Improvements and Section Program corrections Added information related to ST Link release 3 1 in Section New features Section Improvements and Section Program corrections Deleted Applicable tools table and updated part number in cover page 10 Jul 2013 3 1 8 3 6 7 DocID022036 Rev 8 RN0078 Please Read Carefully Information in this document is provided solely in connection with ST products STMicroelectronics NV and its subsidiaries ST reserve the right to make changes corrections modific
8. rance Germany Hong Kong India Israel Italy Japan Malaysia Malta Morocco Philippines Singapore Spain Sweden Switzerland United Kingdom United States of America www st com ky DoclD022036 Rev 8 717
Download Pdf Manuals
Related Search