SAS-113TQ BACKPLANE
Contents
1. Returning Merchandise for Service Chapter 1 Safety Guidelines 1 1 ESD Safety Guidelines 1 2 General Safety Guidelines 1 3 An Important Note to Users 1 4 Introduction to the SAS 113TQ Backplane Chapter 2 Connectors Jumpers and LEDs 2 1 Front CONNectorS eee 2 2 Front Connector and Pin Definitions 2 3 Front Jumper Locations and Pin Definitions Explanation Of Jumpers EEEU IPC and SGPIO Modes and Jumper Settings Front LED INdicators u 2 4 Rear Connectors and LED Indicators SAS 113TQ Backplane User s Guide Contacting Supermicro Headquarters Address Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A Tel 1 408 503 8000 Fax 1 408 503 8008 Email marketing supermicro com General Information support supermicro com Technical Support Web Site www supermicro com Europe Address Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands Tel 31 0 73 6400390 Fax 31 0 73 6416525 Email sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Asia Pacific Address Super Micro Computer Inc 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C Tel 886 2 8226 3990 Fax 886 2 8226 3991 Web Site ww2. Safety Guidelines To avoid personal injury and property damage carefully follow all the safety steps listed below when accessing your system or handling the components 1 1 ESD Safety Guidelines Electrostatic Discharge ESD can damage electronic components To prevent dam age to your system it is important to handle it very carefully The following measures are generally sufficient to protect your eguipment from ESD 1 2 Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing a component from the antistatic bag Handle the backplane by its edges only do not touch its components peripheral chips memory modules or gold contacts When handling chips or modules avoid touching their pins Put the card and peripherals back into their antistatic bags when not in use General Safety Guidelines Always disconnect power cables before installing or removing any components from the computer including the SAS 113TQ backplane Disconnect the power cable before installing or removing any cables from the backplane Make sure that the SAS 113TQ backplane is securely and properly installed on the motherboard to prevent damage to the system due to power shortage 1 1 SAS 113TQ Backplane User s Guide 1 3 An Important Note to Users All images and layouts shown in this user s guide are based upon the latest back plane revision available at the time of publishing The c
3. aircraft emergency communication devices or other critical systems whose failure to per form be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale
4. Drive Failure 2 5 SAS 113TQ Backplane User s Guide 2 4 Rear Connectors and LED Indicators SAS 1 SAS 3 SAS 5 A A id i g dl email al al SAS 0 amp s 2 oh 4 off 6 Figure 2 4 Rear Connectors Rear SAS SATA Connectors Rear Connector SAS SATA Drive Connector Number Number SAS 0 J1 SAS SATA HDD 0 SAS 1 J2 SAS SATA HDD 1 SAS 2 J3 SAS SATA HDD 2 SAS 3 J4 SAS SATA HDD 3 SAS 4 J9 SAS SATA HDD 4 SAS 5 SAS SATA HDD 5 SAS 6 SAS SATA HDD 6 SAS 7 SAS SATA HDD 7 ACT 1 ACT 3 ACT 5 FAIL 1 FAIL 3 FAIL 5 ACT 6 Ezra sent i i zaza H came 5555970 p v O k rat i S530 ji Us WMS Ee o o MI eS i 2 gmail Ter so Ter ao RET sa ACT 7 FAIL 0 FAIL 2 FAIL 4 FAIL 7 Figure 2 5 Rear LEDs Rear LED Indicators Connector Hard Drive Activity Failure LED SAS 0 D12 D5 SAS 1 D13 D6 Rear SAS 2 D14 D7 SAS 3 D15 D8 SAS 4 D18 SAS 5 D21 SAS 6 D22 SAS 7 D25 2 6 Safety Information and Technical Specifications Notes 2 7 SAS 113TQ Backplane User s Guide Disclaimer cont The products sold by Supermicro are not intended for and will not be used in life sup port systems medical eguipment nuclear facilities or systems aircraft aircraft devices
5. ERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate WARNING Handling of lead solder materials used in this product may expose you to lead a chemical known to the State of California to cause birth defects and other reproductive harm Manual Revision 1 0a Release Date May 11 2010 Unless you reguest and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2010 by Super Micro Computer Inc All rights reserved Printed in the United States of America Safety Information and Technical Specifications Table of Contents Contacting Supermicro
6. SUPER Bim C SAS 113TQ BACKPLANE USER S GUIDE Rev 1 0a SAS 113TQ Backplane User s Guide The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software and documentation is the property of Supermicro and or its licensors and is supplied only under a license Any use or reproduction of this product is not allowed except as expressly permitted by the terms of said license IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOV
7. ard you have received may or may not look exactly the same as the graphics shown in this manual 1 4 Introduction to the SAS 113TQ Backplane The SAS 113TQ backplane has been designed to utilize the most up to date tech nology available providing your system with reliable high quality performance This manual reflects SAS 113TQ Revision 1 02 the most current release available at the time of publication Always refer to the Supermicro Web site at www supermi cro com for the latest updates compatible parts and supported configurations 1 2 Safety Information and Technical Specifications Chapter 2 Connectors Jumpers and LEDs 2 1 Front Connectors 29 an 12 S Tae i Figure 2 1 Front Connectors Front Connectors and Jumpers 1 Power Connectors 4 pin JP10 JP13 10 Connector 5 J12 2 Upgrade Pin JP46 11 Connector 4 J10 3 MG9072 Chip 12 Connector 3 J8 4 Sideband 1 JP51 13 Connector 2 J7 5 Sideband 2 JP52 14 Connector 1 J6 6 1 C Connector 1 JP44 15 Connector 0 J5 7 IC Connector 2 JP45 8 Connector 7 J16 9 Connector 6 J14 2 1 SAS 113TQ Backplane User s Guide 2 2 Front Connector and Pin Definitions 1 Backplane Main Power Connectors Backplane Main Power The 4 pin connectors designated JP10 provide 4 Pin Connector power to the backplane See the table on the Pin Definition ri
8. ght for pin definitions 1 12V 2 and 3 Ground 4 5V 2 Upgrade Connector The Upgrade connector designated JP46 is for diagnostic purposes only This connector should only be used by a certified and experi enced technician 3 MG9072 Chip The MG9072 is an enclosure management chip that supports the SES 2 controller and SES 2 protocols 4 and 5 Sideband Headers Sideband Headers The sideband headers are designated JP51 and JP52 For SES 2 to work properly you rabii A MEK SDIN 1 Controller must connect an 8 pin sideband cable See the Backplane ID SB6 table to the right for pin definitions gt va SDOUT I C GND SB2 Reset SB4 GND SB3 SLOAD SDA SB1 Backplane SCLOCK ID SB7 SCL SB0 No Connec No Connec tion tion 2 2 Safety Information and Technical Specifications 6 and 7 l2C Connectors l C Connector The I C Connectors designated JP44 and ee JP45 are used to monitor HDD activity and status See the table on the right for pin definitions Pin Definition ji Data Ground 2 3 4 No Connection 8 15 SAS SATA Connectors The SAS SATA connectors are numbered 0 through 7 Each may be connected to the system with a SAS or SATA cable 2 3 SAS 113TQ Backplane User s Guide 2 3 Front Jumper Locations and Pin Definitions Figure 2 2 Front Jumpers Exp
9. lanation of Jumpers oe Connector To modify the operation of the backplane n jumpers can be used to choose between optional settings Jumpers create shorts between two pins to change the function Jumper of the connector Pin 1 is identified with a square solder pad on the printed circuit board Note On two pin jumpers Closed Setting EE means the jumper is on and Open means the jumper is off the pins Ao N Jumper Settings Jumper Settings Open Default Closed Reset Buzzer reset Open Default Closed Reset MG9072 chip reset The buzzer sound indicates that a condition requiring immediate attention has occurred The buzzer alarm is triggered by the following conditions 1 Hard drive failure 2 System temperature over 45 Celsius 2 4 Safety Information and Technical Specifications IC and SGPIO Modes and Jumper Settings This backplane can utilize IFC or SGPIO SGPIO is the default mode and can be used without making changes to your jumpers The following information details which jumpers must be configured to use 1 C mode or restore your backplane to SGPIO mode IPC and SGPIO Settings Jumper I2C Jumper Setting SGPIO Jumper Setting Default Note JP33 2 3 1 2 Controller ID Front LED Indicators Figure 2 3 Front LEDs Front Panel LEDs Specification Overheat or
10. w supermicro com tw Technical Support Email support supermicro com tw Tel 886 2 8226 1900 Safety Information and Technical Specifications Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required be fore any warranty service will be rendered You can obtain service by calling your vendor for a Returned Merchandise Authorization RMA number When returning to the manufacturer the RMA number should be prominently displayed on the outside of the shipping carton and mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service RMA authorizations may be requested online http www supermicro com support rma Whenever possible repack the backplane in the original Supermicro box using the original packaging materials If these are no longer available be sure to pack the backplane in an anti static bag and inside the box Make sure that there is enough packaging material surrounding the backplane so that it does not become damaged during shipping This warranty only covers normal consumer use and does not cover damages in curred in shipping or from failure due to the alteration misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems Safety Information and Technical Specifications Chapter 1
Download Pdf Manuals
Related Search