DT523 English - UPM Marketing
Contents
1. note that in the event of a power failure or if the on and off times are identical the timer will go back to operating as a dawn to dusk timer See the following example of program setting on pages 7 and 8 INTRODUCTION The DT523 is a dusk to dawn timer This heavy duty outdoor timer is ideal for use with 2 or 3 prong plug in devices such as security lighting seasonal lighting patio lighting and other devices you would operate at night It can be set to operate in one of three modes 1 Continuously on from Dusk till Dawn 2 On at night limited by a program 3 Manually switched on For more information on Dusk to Dawn function see page 4 Setting the Clock see page 5 Programming see page 6 Manual function see page 4 Technical specifications see page 9 Warranty see page 9 ELECTRICAL SETUP 1 Plug the timer into a standard 120V electrical outlet then plug your lighting Or another device into the timer outlet 2 Ensure the device is in the ON position For example if a lamp is plugged into the timer ensure that the lamp s on off switch is in the ON position 3 Press and hold MODE for 3 seconds to activate the ON OFF manual override to test if the device is working Note Ensure the load does not exceed the maximum load rating of 1800W resistive or 600W tungsten PROGRAMMING ON TIME Program Diagram PROGRAM ON TIME ATI o PROGRAM OFF OFF TIME BUTTONS LCD DISPLAY Butto2. OWNER S MANUAL This heavy duty outdoor timer is ideal for use with security lighting seasonal lighting or patio pond lighting Please take the time to read and understand this manual to enjoy the benefits of this product FEATURES e Clock display e 1 program daily e Photocell light sensor e Dusk to dawn mode activated by darkness e Manual on off override e Heavy duty design e Weather resistant housing e Standard 3 prong outlet Outdoor Dusk to Dawn Timer with one daily program DT523 EES LCD DISPLAY PHOTOCELL MODE MODE Q PROGRAMMING By setting a program you limit the time the power can go occur between certain hours To do this you must first set the clock and then enter the time you would like it to go on and the time you would like it to go off The power will be turned on if it is dark and it is between the on and off time settings The power will be turned off when the off time is reached or when it is light again which ever comes first For example if you set an on time of 6 pm and an off time of 9 pm and the sun sets at 5 pm and rises at 6 am then the light will go on at 6pm and turn off at 9pm However if you are using the same six to nine program and the sun does not set until 7 30 pm the timer will wait until dark to turn on at 7 30 pm and then off at 9 pm Please
3. erence if you scroll up to 1 00pm because the number will display as 13 00 hours in 24 hour mode This change will affect the program times as well
4. gram mode press MODE to return to the regular clock mode If no key is pressed for 8 seconds the display will automatically return to the CLOCK display MANUAL ON OFF OVERRIDE Press and hold MODE for 3 seconds to manually turn the device ON or OFF Selecting on off manually will temporarily interrupt the dusk to dawn function For example if you manually turn on the light in the middle of the day it will stay on until the first of the following occurs Dawn the next day It encounters the programmed off time You manually turn it off again DUSK TO DAWN MODE This timer is equipped with a photocell that senses ambient light levels In dusk to dawn mode the timer will turn the power on when light levels drop and the unit is in darkness and will turn off the power when it is light again This is the default setting of the timer and it will function in this mode when first plugged in The automatic on off can be tested by covering up the photocell for 8 seconds to turn the power on and exposing it to the light for 8 seconds to turn it off Please note that in the event of a power failure or if the ON and OFF times are identical the timer will go back to operating as a dusk to dawn timer TECHNICAL SPECIFICATIONS Ratings 120V AC 8A 60 Hz Max Load 15A 1800W resistive 600W tungsten Note If the LCD appears blank it may indicate that the electric circuit has been disconnected Double check that the power cords are
5. ns features e LCD displays the time and program settings 1 program daily e PHOTOCELL environmental light sensor activates the timer in darkness in dusk to dawn mode e MODE changes from clock to program mode e SET confirms settings LCD display CLOCK MODE PROGRAM MODE ON TIME OFF TIME l TIME HOUR MINUTE To learn how to set any program use the Program Diagram as a reference Daily Program ON TIME 8 15pm OFF TIME 5 00am Press MODE until PRG ON displays Press SET to begin programming the ON TIME the hour will flash Press MODE to scroll to the correct hour Press SET the minutes will flash Press MODE to scroll to the correct minute Press SET to finish the ON TIME In the Program Diagram the ON TIME is set to 8 15 pm 1 2 3 4 3 4 PM INDICATOR 12 or 24 hour clock PROGRAMMING OFF TIME Once the ON TIME programming is completed you may advance to the OFF TIME Ensure that you have confirmed all ON TIME settings by pressing SET check that no icons are flashing on the LCD screen 1 Press MODE until PRG OFF displays see Program Diagram 2 Press SET to begin programming the OFF TIME the hour will flash 3 Press MODE to scroll to the correct hour 4 Press SET the minutes will flash 3 Press MODE to scroll to the correct minute 4 Press SET to finish the off time In the Program Diagram the OFF TIME is set to 5 00 am To end the pro
6. securely attached to the timer Warning For outdoor installation mount the time at least three feet above the ground with the receptacle plug facing down to avoid a shock hazard 1 YEAR WARRANTY This product carries a one 1 year replacement warranty against defects in workmanship and materials This product is not guaranteed against wear or breakage due to misuse and or abuse If the product is defective return it with a dated proof of purchase to the retailer from which you purchased it Note shipping and handling for returns is not included under this warranty Customer Service Centre 1 888 468 6876 www upm marketing com SET CLOCK 1 Press SET while the CLOCK icon is displayed on the LCD The hour will flash on the LCD display 2 Press MODE to scroll to the correct hour 3 Press SET The minute will flash on the LCD display 4 Press MODE to scroll to the correct minute 5 Press SET After the correct time has been selected the SET icon will disappear and the timer will return to normal clock display with only the CLOCK icon displayed Note To toggle between 12 hour and 24 hour format wait until the time setting is complete when no numbers are flashing but the CLOCK icon is still visible Then press and hold MODE and SET at the same time for 3 seconds to toggle between 12 and 24 hours The time before 12 noon looks the same in either 12 or 24 hour mode but you will be able to see the diff
Download Pdf Manuals
Related Search