User Manual
Contents
1. Wta VisionSystems Safe T Scope Mirror Monitor Backup Camera System INSTALLATION USER MANUAL oe STSK6630 Ge STSK5530 STSK1030 Not Shown 90 21 144th Place Jamaica NY 11435 1 800 227 2095 www roscovision com e WARNING 1 To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are dangerous voltages inside the monitor There are no user serviceable parts inside 2 Avoid exposing monitor to water rain moisture etc It is NOT waterproof Any moisture inside the monitor could cause extensive damage 3 Do not disassemble the camera or the monitor This voids the warranty Disassembling the camera will compromise the waterproof seal e STORAGE 1 Do not expose the monitor to excessive heat or cold The storage temperature of this device is 5 158 F and operating temperature is 5 149 F 2 Do not store or operate in humid environments e GENERAL 1 This system is intended for use in automotive applications Power source should be an automobile storage battery 12V 24V 2 Make sure all cables are connected properly Improper cable connections may damage the monitor Remove the cable connection when you do not intend to use the unit for a long period of time 3 Please install this system according to the instructions in this manual 4 Connect the system to an ignition switched power source Connection to an unswitched battery source will reduce battery life Thi2. Camera mount in suggested location Mount camera assembly high Centered Fig 2 Camera Housing Fig 3 Camera mounting hole pattern 16mm 0 23in 10 Fig 4 Fig 5 pi POWER INPUT LEAD RED To Ignition Switched Accessory GROUND WIRE BLACK To metal point of the vehicle Filter ul gt CAM2 CAM2 REVERSE Trigger WHITE REVERSE Trigger GREEN Reverse Note For typical single camera installation this trigger wire should be connected to the vehicle s back up lights circuit and the rear view camera should be attached to the connector marked REVERSE 12 Camera Connector NOTES 13 VisionSystems 90 21 144th Place Jamaica NY 11435 www roscovision com Ph 1 800 227 2095 Fx 1 718 297 0323 ISO erin FM 78496 A Century of QS 9000 March 1998 FM 78495 Printed in China Automotive Safety Lit P N 04242012
3. bright light Compact and lightweight design installs easily into most vehicles e Waterproof dustproof IP67 rating STSM215 HIGH BRIGHTNESS LCD COLOR 7 MONITOR Menu button for Picture System and Options e Camera 1 Camera 2 e Power stand by switch Built in speaker e Auto dim CONTENTS OF COMPLETE SYSTEM 1 Camera with Accessories Mounting Bracket w hardware 65 Camera extension cable 33 for STSK5530 1 Mirror Monitor with Accessories Power Video Audio Distribution harness with reverse trigger IMPORTANT For typical rear view installation the rear camera MUST be connected to the power harness at the connector marked REVERSE Note The following instructions are for typical rear view application STSC109 CAMERA 1 Find location for camera close to rear marker lights centered on vehicle Attachment point must be sturdy enough to support camera and bracket Fig 1 2 Camera is designed for installation near the top of the vehicle in order to capture images of the rear bumper and danger zones immediately behind the vehicle It is not recommended to be installed near the bumper This reduces the view of critical areas and increases the chance of physical damage to the camera 3 Remove camera cover by removing the screws located at the ends of the camera Remove camera by twisting retaining ring counterclockwise until camera is released Fig 2 4 Drill one inch 16mm hole where the came
4. electrical equipment fitted to petroleum vehicles must be connected via battery master switch and must be isolated from the battery while the vehicle is loading and unloading For other specialty vehicles please check applicable code and regulations prior to installation 10 Always consult your dealer when fitting an electrical or electronic equipment to a vehicle fitted with a CAN bus or multiplex system IMPORTANT For installations requiring multiple cameras or for installations not requiring typical rear view images please refer to the wiring diagram Fig 7 and the particu lar vehicle s electrical schematic for selection of proper power and trigger connection points 0000008000000 e o o o o 200000000000 000000800000 00000000000 200000000000 o o o o o 0 0 0 0 0 0 0 0 00 000000000000 o o o o o o FUNCTIONS AND OPERATION MONITOR 1 POWER When the ignition is switched on the monitor will be in standby mode waiting for trigger signal When a trigger wire is energized by 12v power the image captured by the selected camera will appear on the monitor Pressing the power switch will change the monitor status from standby to steady on Steady on mode status will show camera view depending on user selection 2 LIGHT SENSOR When auto dimming is active monitor will automatically change screen br
5. ightness according to ambient light around the monitor 3 5 Volume Adjust Speaker Volume These buttons are also used to adjust the values within selected setting of menu option 4 MENU Button See p 8 Press MENU to active screen options Press Menu to cycle through choices and to change settings 6 C1 C2 Switches from Camera 1 to Camera 2 and vice versa MENU CONFIGURATION NOTE On screen menu commands should only be selected when monitor is in Steady on mode Never change settings while operating vehicle Press the MENU button once to set desired brightness Press to increase reduce the brightness Wait 3 seconds to exit setup mode Press the MENU button twice to set desired contrast Press to increase reduce the contrast Wait 3 seconds to exit setup mode Press the MENU button three times to set desired color Press to increase reduce the color Wait 3 seconds to exit setup mode Continue to press the MENU button to change desired settings Tint Press to increase reduce the tint Language Press to select English French Spanish Reset Press to restore factory defaults CAM1 Press to select Normal Mirror mode CAM2 Press to select Normal Mirror mode Vertical Press to flip image vertically Dimming Press to select Auto Day Night Scale Press to select On Off for backup grid to appear when in triggered mode Scale Adjustment Press to change
6. ons See Fig 6 2 The monitor terminates in a 13 pin connector which should be connected to the mating 13 pin receptacle end of the power video audio distribution harness When connecting the cables check to make sure to match the directions of the arrows on the 13 pin connectors male to female 3 For typical rear view installation connect the camera extension cable from the rear view camera to the harness connector marked C1 4 For multi camera installations be sure to mark each extension cable properly and connect to the appropriate harness connector marked C1 or C2 Bundle excess cable together using a cable tie or electrical tape 5 The green wire is the REVERSE trigger wire In typical rear view installations connecting this wire to the vehicle s backup light circuit will activate the rear view image whenever the vehicle shifts into reverse 6 Camera Drill a inch 16mm diameter hole into vehicle body near the camera and bracket Insert camera cable into vehicle be careful not to kink cable and fit grommet into hole Apply sealant around grommet to increase resistance to water penetration Connect camera to the camera extension cable which runs inside the vehicle 7 Feed as much cable as possible into vehicle and clamp securely This reduces the possibility of it being hooked or snagged 8 Keep all cables away from HOT ROTATING and ELECTRICALLY NOISY components 9 FUEL TANKERS 8 OTHER SPECIALTY VEHICLES All
7. ra cable will go through the body of the vehicle Make sure there are no obstructions behind your hole Using the camera base as a template drill two 1 8 inch 3 5mm holes for attachment screws Fig 3 5 Attach camera housing to vehicle with screws provided 6 Insert camera back into housing and adjust lens angle to desired setting Note that the light sensor is the bottom of the camera Once the angle is set tighten retaining ring onto camera Tighten set screws on the sides of the camera Fig 4 7 Return top cover and secure with original screws Fig 5 STSM215 MONITOR 1 Attach mirror monitor inside vehicle in a existing interior mirror location e g center of dash or overhead 2 Attach the bracket to mirror mount 3 Fasten mirror monitor to bracket and adjust mounting angle to allow optimum driver viewing comfort STSH365 343 CAMERA EXTENSION CABLE 1 Be sure to position the cable properly The male end attaches to the camera The female end attaches to the power video audio distribution harness typically located under the dashboard 2 Donotrun the cable over sharp edges or corners Do not kink the cable Keep the cable away from hot and rotating parts 3 Fasten all cable runs and secure all excess cable Fig 6 WIRING CAMERA AND MONITOR 1 Monitor Connect the red wire to an ignition switched accessory ex radio power source and connect the black wire to chassis ground See wiring diagram for connecti
8. s device complies with Part 15 ofthe FCC Rules Operation is C subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation E 1 3 11 High voltages exist within the monitor Opening of monitor case is unsafe and never necessary for operating purposes 2 In case of any failure please tum off the display at once and notify our company or the corresponding dealer The monitor is made up of many precise electronic components Any disassembly or modification may lead to damage and voiding of warranty COLOR BACKUP CAMERA SYSTEM Color Mirror Monitor INTRODUCTION Please read this manual thoroughly This manual contains instructions to make the installation of the camera and monitor easier The mirror monitor backup camera system is an upgrade to standard rear view mirror systems and will provide additional rear view vision when installed and maintained properly It is not intended in any way to be a substitute for careful and cautious driving All applicable traffic laws and motor vehicle safety regulations must still be obeyed FEATURES STSC109 CAMERA 40 000 pixel image sensor 0 5 Lux sensitivity 6 IR LED Auto White Balance AWB Field of view 150 Diagonal Back Light Compensation BLC e Automatic electronic iris provides a clearer more consistent image in low and
9. selected line on backup grid Press to adjust position of line on backup grid Wait 3 seconds to exit setup mode SPECIFICATIONS STSC109 CAMERA PICK UP DEVICE TV SYSTEM PICTURE ELEMENTS SENSING AREA IMAGE SIZE SYNCHRONIZATION HORIZONTAL RESOLUTION REQUIRED ILLUMINATION SIGNAL TO NOISE RATIO POWER SUPPLY POWER CURRENT LENS ANGLE OPERATION TEMPERATURE STORAGE TEMPERATURE WEIGHT DIMENSIONS W x H x D STSM215 MONITOR SCREEN 7 0 inch ANGLE VOLTAGE POWER CURRENT TV SYSTEM VIDEO INPUT OUTPUT RESOLUTION CONTRAST LCD BRIGHTNESS OPERATING TEMPERATURE STORAGE TEMPERATURE DISCLAIMER CMOS NTSC 720 H x 480 V NTSC 5 6mm x 5 6mm 1 4 inch INTERNAL 420 TV LINES 0 5 LUX MINIMUM F 1 2 MINIMUM 45dB 12Vdc 1 8W AT 12VDC MAX 75mA 150 D 5 F to 149 F 20 C to 65 C 5 F to 167 F 20 C to 75 C 0 1Kg 0 23lbs 3 3 x 2 28 x 1 74in 83 5 x 57 8 x 44 2mm COLOR TFT LCD HIGH BRIGHTNESS 70 TOP 50 DOWN 70 LEFT RIGHT 12 24 VDC 12W MAX 850 mA at 12VDC NTSC COMPOSITE VIDEO SINGLE 1VP P 75 OHM 800 H x 480 V 300 1 1000cd m2 5 F to 149 F 15 C to 65 C 5 F to 158 F 20 C to 70 C The use of the Rosco s Vehicle CCTV system should not in any way be used as a substitute for careful and cautious driving Always obey traffic laws and motor safety regulations must always be adhered to Specifications subject to change without any notice
Download Pdf Manuals
Related Search