Home

Lighton Series (Lighton 3 / Lighton 5) User Manual

1. 1 Press A to select the Sub Switch 2 Press B to set the Universe 3 Press C to select Enable and select the output ArtNet 4 Press D to select Disable and disable the output ArtNet Press MENU to exit 33 WORK 9 LightOn Series User Manual LOAD AND COPY LIBRARY LightOn console allows the operator the ability to copy and load the libraries information from the submaster mode ML mode moving heads the LED mode and Patch information from the console to a USB memory devices libraries being very useful to copy to another console To access this feature perform the following steps 1 Activate the Single or Scene Two Scene modes by their corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Set Up BUFFER Patch DMX BASE LedSet A 000 Toss Next 4 Press the key D corresponding to Next again as shown in the image below Hd Huch sw BUFFER VGA SC BASE Dmx_Bs A 255 TI Next 5 Then press the key C corresponding to Upload Lib as shown in the image below Set BUFFER Set DMX Upload BASE Lib Cc 34 LightOn Series User Manual WORK 9 6 Once inside you can select from 4 options 1 Press the key A for Upload System to copy the entire library system on a USB stick 2 Press the key B corresponding to Fix Upload
2. Sub BUFFER 13 Page BASE 37 All Fader 12 255 Exit Le 3 Press any FX1 Fx2 Fx3 Fx12 key the effect where you want to record The button will lit in blue colour and the display shows the following Sub BUFFER FX Base 13 a BASE 37 Next x Fx 01 S 000 T 000 Back In Looking at the bottom side of the display it shows information about the status of this Fx S000 refers to the current step within Fx by contrast Txxx refers the total number of steps stored within this Fx 4 Adjust the channel level from 1 to 48 for the first step 5 Press Step to store the first scene in the Fx 6 Adjust the channel levels from 1 to 48 again for the second step 7 Press the key Step again to store the second scene in the Fx 8 The scenes continue storing the same way Once stored all desired scene press the Fx that lits in blue colour to finish the recording 67 LightOn Series User Manual WORK had FX Edition If during scenes recording we want to move between stores scenes to eliminate a step or to remove the entire Fx we can make it through the A B C and key Ds key A Deletes the current step this is indicated through Sxxx key B Deletes entirely all Fx steps leaving it clean key C Allows to select the steps moving us forward key D Allows to select the steps moving us backwards If you want to edit an already stored Fx we will p
3. 6 Press a selection button 1 to 12 The buttons will stop flashing you will have recorded the group Example 3 Making a group with the devices on rear truss 1 Select ML mode 2 Press the selection buttonsof the devices located on rear truss in this case 5 6 7 and 8 to activate them 3 Press the button Menu 4 Press the key C corresponding to Record Group 5 Press the selection button 1 to store the devices in group 1 6 Press the Menu key to exit 7 Press the key B corresponding to Recall Group 8 Press the selection button 1 We can work with all devices on rear truss at the same time 82 LightOn Series User Manual Delete In ML mode LightOn console has two delete functions A Delete Fixture With it you can remove the patched devices WORK B Delete Chase With it you can eliminate chases or programs stored in the preset faders A Delete Fixture The steps to remove the patched devicesare 1 Activate ML mode through corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below CLEAR BUFFER DMX BASE RH Fixture Menu Fix Patch Channl Setup Record Group Fader 01 000 Next 4 Then press the key A corresponding to Delete CLEAR BUFFER DMX BASE RH Fixture Menu Delete List Fix Auto DMX Fader 01 000 Next
4. Assign Fade Fade A Fade B RH FX Fader 12 255 HUE 71 LightOn Series User Manual 2 Press Record key CLEAR BUFFER DMX BASE x RH Submaster Mode Del Sub 01 Del 13 Page 25 Del 37 All Fader 12 255 Exit 3 Press DMX BASE key located in the left side of the display It will lit in blue colour 4 Press any Fx1 Fx2 Fx3 CLEAR BUFFER DMX BASE MEN Fx12 button This button will flash in pink colour 5 Press key A corresponding to BBT Record CLEAR BUFFER DMX BASE RE 6 Press key A corresponding to AUTO Record CLEAR BUFFER DMX BASE x lt RH Record DMX Base BBT Record A BBT RECORD Dmx B DMX RECORD Record C DEL BASE 01 D DEL ALL BASE Delete Recording EXIT Base Pg 01 Record Sub DEL A BBT Record Set Auto Record MANUAL Record Pg 01 Record Sub Exit BBT Record Set Yes Yes Will cancel other function No Exit Free Space No 51200K Pg 01 Record Sub 72 WORK HU HOH Wich HEE 9 LightOn Series User Manual 7 Press key A corresponding to Yes CLEAR BUFFER DMX BASE x RH BBT Record Set Recording TIME 00 00 Pg 01 Record Sub Exit When you want to stop de recording process press key D corresponding to Exit
5. The LightOn console includes the most libraries commercially available devices All of them are stored in the USB memory The LED mode menu has its own Sub menus below shows a diagram 101 LightOn Series User Manual WORK had Fix Patch Each LED device can be assigned to a fade preset thus we can select the device quickly via these selection buttons 1 to 12 T he main function of patching equipment is to indicate which unit is located in each preset fader and indicate its direction The steps to patch a LED fixture are 1 Access the LED mode via the corresponding button mew Fixture Menu Fix Patch BUFFER Setup DMX Record BASE Group x Fader 01 000 Exit 2 Press key A corresponding to Fix Patch Read 00 Fixture CLEAR BUFFER DMX BASE n RH Fader 01 000 HU Mich The console will start scanning the libraries available from the USB memory once it indexed them Total 01 CLEAR DMX More e Fader 01 000 Enter In 102 LightOn Series User Manual WORK had 3 The units are indexed by manufacturer Through the A B and key Cs for Back Next and More you can go moving us Once you locate the manufacturer select it through the key D for Enter 4 The console indexes the LED devices to the selected manufacturer Through the A B and C keys for Back Next and More may be movin
6. CLEAR Password DMX e Master 255 Enter In EXT BUTTON ASSIGNATION This function is controlled by the auxiliary buttons EXT1 4 which enable the DMX devices on or off This allows to control up to 4 effects dance to sound and moving heads all from a single console These auxiliary channels are not connected to the rest of the console so that the function does not affect these BlackOut four channels Can only be enabled disabled from the corresponding key EXT1 4 lt The steps for performing the allocation are 1 Activate the Single Mode or Scene Two Scene by their corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Set Up BUFFER Patch DMX BASE LedSet Cc SS e mn CS 45 LightOn Series User Manual WORK 9 4 Then press the key D again for Next as shown in the image below gt e HH SW BUFFER VGA BASE Dmx_Bs A 255 TI Next 5 Then press the key D again for Next as shown in the image below Set BUFFER Set DMX Upload BASE Lib Master 255 Next 6 Then press the key D again for Next as shown in the image below Files BUFFER Passwrd BASE Memory Master 255 Next MH 46 LightOn Series User Manual 7 Then press the key A corresponding to Assign EXT to access the function
7. WORK x a Lighton Series CLighton 3 Lighton 5 ech wg EikbikkAkiE bebakabakakakakak Fed Green Woe A awe imines Color PRESET User Manual Rev 12 03 04 LightOn Series User Manual WORK INDEX Before d E A CONTENTS OF THE BOx in tn nEs tE nE ESEAtES NENES NEEEESEENESEES EANES ENESE SEESE EnEn En Ene En 3 BE Ne 3 INFORMANON D 3 SPECIFICATION E A dee e Det EE 5 effet 6 del RE 7 CONTROL ELEMENTE 12 CONNECTION 14 Using Hl dE 15 Channel COmmQuration 2 scsecccdeeveasssetegvethcctinzecezcansbedegvebs EE dd Eed REENEN EERdEEdE eege 15 Channel Assign Dmx Patch 16 LCD panel ET 21 Console Software Update sciiicet aaa iii aede Earias aeai 22 VGA card Softaware Update ccccccceccceeceeeeeeceeceeeeeeeaaeeeeeeseaaeaeceeegdaaeceseeeeesaeeeeeeseeeeaeeeeess 24 Dmx Base Update eee ea eae A Ee E E aves E E AA E E need 25 VGA Card EE UE 29 ArtNet Output SettiN gsr egar des vets eira tne EE d e it a NEE ENEE ENEE 31 Load amp Copy LIBRARY ergi eege ee deed irai r i ET Eri NEn 34 System files COpy rrerapen a rre Ea n dle eden Reed LAR dE 36 Password Change aicci aeaa eet E E EE Eaa E E E E E EAS 40 Memory LOCK sisieun aaa aAA Eia ri E EE A EAN ia 43 EXT b tt ns ASSIQMALON sirine a aE E aa a EEE E aE E rai 45 Software INONMA t ON sseni eiiiai aiiiar eniai iiaii Edel 48 Menu Dia Qian sts cciat sccecsencs see sccetveccdstecdcapeh steed aana a a E de da a aaa E E aa a
8. the scene 3 5 The LCD display shows the percentage value of both input and output fade 62 LightOn Series User Manual WORK 9 RECORD FUNCTION LightOn console allows the operator to perform up to 3 different recording functions 1 Submaster Record It has been used previously to explain the submaster mode pg XXX 2 FX Record You can store up to 12 Fx from Single Scene Two Scene and Submaster modes 3 DMX BASE Record To store DMX data from an external device SUBMASTER RECORD Previously it has been explained in detail how to work in submaster mode as summarized below for briefly You can go to the submaster section page XXX for more information Example 1 Recording a submaster 1 Select Two Scene or Single Scene mode 2 Set the Grandmaster to 100 3 Raise the preset faders 4 Adjust the level of the desired channels eg raise the fader 1 2 and 3 5 Press Record the selection buttons for each channel will flash in red colour 6 Press the selection button of the channel where you want to save the scene eg 1 7 Check the display to see how the recording process starts once it finish the red colour buttons will turn off again leaving in green colour the channels that we have adjusted their levels 8 Set all channels to 0 9 Click on submaster to access this mode 10 Raise the fader 1 where we recorded above to activate the scene 63 LightOn
9. CLEAR BUFFER DMX BASE JEBE Menu Assign EXT REV 1 20 Master 255 Back WORK MH 9 8 Once inside you can toggle each of the 4 EXT between Momen or Latch through its corresponding key key A EXT1 key B EXT2 key C EXT3 C key D EXT4 CLEAR BUFFER DMX BASE FX JEBE Assign EXT Momen 1 Latch 2 Latch 3 Master 255 Latch 4 47 HH LightOn Series User Manual WORK had SOFTWARE INFORMATION LightOn consoles receives software updates constantly in order to achieve greater flexibility and better possibilities For the current version of the console software the steps are 1 Activate the Single Mode or Scene Two Scene by their corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Set Up BUFFER Patch DMX aooo CS 4 Then press the key D again for Next as shown in the image below SW BUFFER VGA DMX Update BASE SECH c EEN vn CS 48 LightOn Series User Manual 5 Then press the key D again for Next as shown in the image below CLEAR BUFFER DMX BASE x RACH 6 Then press the key D again for Next as shown in the image below CLEAR BUFFER DMX BASE Pie x 7 Then look at the key B for REV X XX which indicate the current version of softw
10. Press the key D the key for Next to access the following options page function DwLoad BUFFER DwLoad BASE DwLoad Master 255 Next In 10 When you select the option Next proceed to the next page of options which can select among 4 other options 1 Press the key A for ML DwLoad to import all the information stored and existing configurations in ML mode for moving heads from a USB memory 2 Press the key B corresponding to Led DwLoad to import all the information stored and existing configuration in LED mode from a USB memory 3 Press the key C corresponding to Patch DwLoad to import information of console patching a console from a USB memory 4 Press the key D for Next to access the following options page function DwLoad BUFFER DwLoad BASE DwLoad 11 When you select the option Nex you proceed to the next page of options in which we can select from other 2 options 1 Press the key A for FACTORY RESTOR to thoroughly clean the console of any configuration before importing data from a USB stick 38 LightOn Series User Manual WORK 9 2 Press the key D for Next to return to the first page of feature options RESTOR ES BUFFER DMX NOTE If the case that during the import of configurations for a single object from the USB to the console this also contains data these are replaced by the USB memor
11. B The steps are as follows for use Manual Record function 1 Access to Submaster mode through its corresponding button CLEAR BUFFER DMX BASE x ree 2 Press Record button Submaster Mode 01 13 25 37 Assign Fade FadeA Fade B Fader 12 255 73 WORK HH HH 9 LightOn Series User Manual CLEAR BUFFER DMX BASE X RH Submaster Mode Del Sub 01 Del 13 Page 25 Del 37 All Fader 12 255 Exit 3 Press DMX BASE key located in the left side of the display It will lit in blue colour 4 Press any Fx1 Fx2 Fx3 CLEAR BUFFER DMX BASE nm ree Fx12 button This button will flash in pink colour 5 Press key B corresponding to DMX Record CLEAR BUFFER DMX BASE kul x lt RH 6 Press key A corresponding to MANUAL Record CLEAR BUFFER DMX BASE ky x RH Record DMX Base BBT Record A BBT RECORD Dmx B DMX RECORD Record C DEL BASE 01 D DEL ALL BASE Delete Recording EXIT Base Pg 01 Record Sub DEL AN BBT Record Set Auto Record MANUAL Record Pg 01 Record Sub Exit BBT Record Set Yes Yes Will cancel other function No Exit Free Space 51200K No Pg 01 Record Sub 74 WORK HH HE HH HH 9 LightOn Series User Manual 7 Press key A corresp
12. Fader 12 255 In Example 3 Assign a fade time at preset A 1 Press the key A for Fade A on the right of the display 2 Set the Fade Time to 1 30 using the Step Rate fader CLEAR o1 MEER BUFFER 13 DNX 25 MERE BASE 37 Fade B X Fader 12 255 RH MH 3 Press the key A again to clear the option Fade A 4 Raise the preset A to 100 and then lowered to 0 As you ve noticed now when you raise or lower the preset A fader it is not controlled by the speed of your movement but it works independently as fade times we have assigned Just as we have assigned a Fade time to preset A we can do with the preset B Even with the two simultaneously selecting both and then adjusting the Fade Time 5 Press the key A again for Fade A and adjust the Fade Time to 0 disabling the fade time Therefore the fader mode Preset A will work directly 53 LightOn Series User Manual Example 4 Using the Crossfade WORK For this exercise will depart from 0 leaving behind the previous 3 exercises 1 Press Single Scene being the key in green colour 2 Ensure that GrandMaster is set to 100 3 Raise the Preset A and Preset B faders 4 Press the key Next this will light in red colour LELAA LEE 5 Move the channel faders to adjust the channel levels for scene A For example channel through 12 to 100 6 Down the faders of Preset A a
13. for Next to select Work 7 Press the key D corresponding to Enter 8 Press the key D corresponding to Enter to select the appliance WKB572C1 9 Press the select key 1 and hold it down 10 Press the select key 8 Thus we have patched 8 Work 575 Blade devices once 79 LightOn Series User Manual WORK 9 Example 2 Patching a device on a DMX address given 1 Select ML mode 2 Press the Menu button 3 Press the key A for FixPatch 4 Press the key C for More 5 Continue pressing the key C for More to see the display Work 6 Press the key B for Next to select Work in the display 7 Press the key D corresponding to Enter 8 Press the key D corresponding to Enter to select the appliance WKB572C1 9 Introduce the DMX address where we want to patch it through the buttons FX1 FX2 FX10 eg 216 10 Press the select key 1 Thus we have patched 1 Work Blade 575 device in the address 216 Channel Set Up Thus we definy from which channel will be patched each of the different types of devices which supports LightOn console Steps to follow 1 Activate ML mode by the corresponding buttons 2 Press Menu button 3 Press the key B corresponding to Channel Setup as shown in the image below Patch BUFFER Setup DMX Record BASE Group c 80 LightOn Series User Manual WORK had 4 Once inside you will see the all
14. 124 LightOn Series User Manual WORK 3 Define the type of channel Shutler 4 Set the default value when we locate the heads from the console 125 LightOn Series User Manual work I Example 6 Creating Palettes Palettes or Presets in a device can be defined from File gt Edit Palette sf Palette Edit R Chi aiu CG EHA 5 Ch paate set Shutter Pan E Tilt TC Dimmer TC Colour Goor E Focus 1 F Gebei M Gobo2 F GobolRot F GoboSpin E Prism F Maco NS EICH 126 LightOn Series User Manual WORKI I We can define up to a maximum of 10 palettes Press the Update Setting button you assign a name to the Palette and select the attributes we wan definy in the palette e Palette Tt Ary ii The process for presets creation is exactly the same we select one of the 10 entries on the left we add a name and then assign a value Chi DG Ch3 Chi Chi Che Ch Che ChS Dun Chi hi2 Ch3 Chi4 Cup Dip Chi Chis Chis Ch20 23 Ch24 Ch25 D Ch2 Ch28 Ch29 Ch30 Ch31 Ch32 Ch33 Ch34 Ch35 Crab Ch37 Ch38 Ch39 d 127 LightOn Series User Manual work I Just as we edited the library with a moving head can do with a LED device therefore we move to Fixture LED Menu gt LED Fixture Edit To edit a LED device library the process is exactly like the Moving Heads k LED Fitiire L t Once created the libraries you can copy to your LightOn console via
15. 20 LightOn Series User Manual WORK had LCD PANEL ADJUSTMENT Lighton consoles have a 60 x 128 dots TFT LCD display with contrast adjustment We can adjust the contrast and brightness of the panel to achieve optimal vision Steps to follow 1 Activate the Single Mode or Scene Two Scene by their corresponding buttons 2 Press Menu 3 Press the key C corresponding to LcdSet as shown in the image below Set Up BUFFER Patch DMX a aco we Ce 4 By pressing C corresponding to gt we can move and change between the Contrast and Brightness Adjustment Use the keys A and B for UP and Down respectively to adjust the values Thus we can adjust the LCD panel to achieve optimal vision as shown in the image below mew Led Contrast Up aes 20 Dow Light gt High i A 255 Ti aain Ener p 5 After making the appropriate changes will press the key D Corresponding to Enter to save them 21 LightOn Series User Manual WORK 9 CONSOLE SOFTWARE UPDATE Through this menu you can update the console software to the latest version For more information please go to the Equipson official website www equipson es Once downloaded the file store it in a USB stick under the path SOFTWARE BIN WORK1248 SOFTWARE BIN The path and file name should not be changed under any circumstances otherwise the console will not find the BIN file Steps
16. LightOn Series User Manual WORK had In case of not worry about Fade times during programming LightOn console allows the operator to allocate Fade times after having been programmed You can even edit submasters with fade time previously assigned Example 3 Reassign or Record a new Fade time 1 Select TwoScene or SingleScene mode 2 GrandMaster must be set at 100 3 Raise at top the preset faders 4 Adjust the level of the desired channels eg this time we raise the fader 7 8 and 9 5 Press Record the selection buttons for each channel will flash in red colour 6 Press the selection channel button where you want to save the scene eg in this case 3 7 Look at the screen to check the recording process once finished this process the red colour buttons will turned off again leaving in green colour the channels that we have adjusted the levels 8 Set all channels to 0 9 Click on submaster to access this mode 10 Press the key A Corresponding to AssignFade located to the right of the screen 11 Hold down the select button to be edited submaster p eg this time the 3 12 With the select button pressed adjust the Fade Time through the fader Step Rate 13 Releas the select button in this case 3 and press the key A again corresponding to Assign Fade As you noticed now when you raise or lower the channel 3 fader this is not controlled by the speed of your movement it works independentl
17. PRESET LightOn Series User Manual work T CONFIGURATION AREA Lighton consoles have a TFT LCD display with adjustable contrast and 60 x 128 dots By this display can perform all configuration tasks and setting parameters patch scenes libraries and software updates We can access the console menu by pressing MENU and navigate through it with the A B C and D buttons 10 LightOn Series User Manual work I GRANDMASTER AREA By default the Grand Master controls the HTP channels and playbacks console respectively Over the Grand Master we have the BLACKOUT key When you press this key all HTP taken zero leading to an Dark When released all HTP return to their output levels LTP channels unaffected by BLACKOUT key 11 LightOn Series User Manual WORK had Control Elements Key 1 24 amp Key 25 48 Used to select the top or bottom page Choosing the key 1 24 to the master fader 1 24 and the key 25 48 for the master fader 25 48 Key 1 Key 2 Key 3 Key 24 Selection of devices or pulse pulse 1 pulse 2 pulse 3 Pulse 48 separately Single Scene Used to enter in Single Scene mode TwoScene Used to enter in Two Scene mode SubMaster Used to enter in SubMaster mode ML Moving Light Used to enter in ML mode and to work with moving heads PlayBack Used to enter in Playblack mode NEXT Used to process the Crossfade function in Single Scene mode Record Us
18. Raise the fader Attrb and see how we change the gobo devices Usin the key C corresponding to Attrib we assign the fader Attrb the desired function from the gobo wheel to the iris focus prism tone Example 4 Recording a PlayBack from Example 3 1 Press the Record key 2 Press any selection PlayBack button 13 to 20 To select the playback 3 Press the Playback selection button again To save the step 4 Press the ClearBuffer key 5 Press the Record button To stop recording 6 Raise the recorded PlayBack fader As you can see we have pressed the ClearBuffer button when we finished recording the Chase Otherwise when we were to run would overwrite the Chase and not run properly Example 5 Recording steps in a PlayBack from Example 3 1 Press the Record key 2 Press any selection PlayBack button 13 to 20 different from the example above To select the PlayBack 3 Press the Playback selection button again To save the step 4 Modify the Pan position Tilt and color 5 Press the Playback selection button again To save the step 6 Assign a different function to Attrb fade and change the gobo 97 LightOn Series User Manual WORK 9 7 Press the Playback selection button again To save the step 8 Press the ClearBuffer key 9 Press the Record button To stop recording 10 Raise the recorded PlayBack faders On this occasion we recorded a series of steps i
19. adjust step time 11 Press the selection PlayBack button again To select the PlayBack 12 Press the ClearBuffer button 13 Press the Record button to end recording Running the PlayBack that we recorded we will see how the steps are happening as the fade and step time we have assigned Example 7 Use of pallets from example 3 1 Press the Menu key to exit the Attrb function 2 Press the key A corresponding to Preset Pallet 3 Press the key A for Colour To view the color palettes 4 Press any key A B and C to switch between colours 5 Press the key D corresponding to More to see more color palettes 6 Press the Menu key again to go back During programming of the devices the operator often used certain positions colours etc Like the palette of an artist Lighton console can invoke them offering a maximum of 10 pages of 10 palletes Example 8 Using Shape figures generator from example 3 1 Press the Menu key to exit the Attrb function 2 Press key D corresponding to Next 3 Press the key A corresponding to Shape 4 Press any key A B and C for Circle Figure Fan respectively Eg Circle 5 Adjust the parameters of Radius Radius Up and Down with the keys A and B respectively 6 Press the key D for Next 7 Press the key B corresponding to RUN to implement the Shape 8 Press the key D corresponding to Stop to stop the Shape 99 LightOn Series User Manual WO
20. can be seen in the bottom of the display shows the number of playback and what step you are changing Using the A B C and key Ds you can select the attributes that you want modify 8 Press the key D for Next to move to the next page of the submenu CLEAR 02 XBanDa S BUFFER 1 Red 127 2 Green 064 DMX PL 01 001 T005 Next In Use the keys A and B for Up and Down respectively you can move between the different steps containing the PlayBack If you want to delete a step select it and press the key C corresponding to Delete to delete it 112 LightOn Series User Manual WORK 9 9 Press the key D for Next to move to the next page of the submenu mew Modify Playback Cover aA TERR 02 XBanDa i i BUFFER T Red eg nse 2 Green 064 DMX Blue 3 Blue 012 Record x PL 01 S001 T005 Next p J Through the key B for Insert you can add another step in the PlayBack Once added we select the key C for Record to store the changes 10 Press the key D for Next to move to the next page of the submenu Record we Modify Playback by Cha CLEAR 02 XBanDa Loop BUFFER 1 Red 127 On 2 Green 064 3 Blue 012 BASE We set the PlayBack to run in loop mode or only once by pressing key B corespondiente to Loop On In addition we can correct or add a shape already stored on any step by pressing key C corres
21. lowered the level of the faders to 0 before switching to SubMastre This is because the console allows the operator to maintain the current settings of the faders like the scene in the background If you prefer to cancel this configuration you must press the CLEAR BUFFER key located in the left side of the display to eliminate it mew Submaster Mode Assign Fade CLEAR 01 BUFFER FadeA 13 ade BASE 37 x Fader 12 255 H Example 2 Recording a submaster with fade time 1 Select Two Scene or Single Scene mode 2 Adjust the level of the desired channels eg this time we raise the faders 4 5 and 6 3 Press Record the selection buttons for each channel will flash in red colour 4 Adjust the Fade value through the Step Rate fader eg to 1 second 5 Press the select channel button where you want to save the scene eg this time select the fader 2 6 Look at the display and check how the recording process starts once it finish the red colour button were turned off buttons again leaving in green colour the channels that we have adjusted the levels 7 Low all channels to 0 8 Push submaster button to access to this mode 9 Raise the fader 2 where we recorded above to activate the scene As noted now when raise or low the fader 2 this is not controlled by the speed of their movement but works independently according to fade times we have assigned 58
22. select the key C for Record to store the changes 10 Press the key D for Next to move to the next page of the submenu CLEAR BUFFER DMX BASE FX RH e Record Modify Playback by Cha Pan Loop Tilt On Color Dimmer Sh Shutter SES PL 01 S001 T005 Back We can set the PlayBack to run in loop mode or only once by pressing key B coresponding to Loop On In addition we can correct or add a shape over already stored step by pressing key C corresponding to Shape WORK H MH 11 To return to the first page of Modify PlayBack function press the key D corresponding to Back 90 9 LightOn Series User Manual The diagram for PlayBack Modify menu function is as follows 91 WORK Page 4 9 LightOn Series User Manual WORK I P T Invert LightOn console allows the operator to reverse the Pan and Tilt of the devices from the console This can be set to Normal or Reverse The steps for using the Modify PlayBack are 1 Activate ML mode via the corresponding buttons 2 Activate the devices we want to change through their rrespective selection buttons 1 12 3 Press Menu button 4 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup DMX Record BASE Group c Fader 01 000 Next In 4 Then press the key D corresponding to Next BUFFE
23. to Modify PlayBK Modify BUFFER Invert DMX Memory BASE Lock C Fader 01 000 Back In LightOn Series User Manual WORK 9 6 The display will prompt you to select the playback you want to modify mewu Hit Playback BUFFER Fader 01 000 Exit In 7 Press the selection PlayBack button 13 20 that want to modify menu Modify Playback Focus Pan CLEAR l Color Bax Dimmer i SE Se S PL 01 001 T005 Next bp J As can be seen in the bottom of the display it shows the number of playback and what step we are modifying Through keys A B C and D you can select the attributes that you want modify 8 Press the key D for Next to move to the next page of the submenu Pan CLEAR i Color DMX Dimmer PL 01 S001 T005 Next In Use the keys A and B corresponding to Up and Down respectively you can move between the different steps containing the PlayBack If you want to delete a step select it and press the key C corresponding to Delete to delete it 89 LightOn Series User Manual 9 Press the key D for Next to move to the next page of the submenu Modify Playback CLEAR BUFFER DMX BASE BID Cover Pan Tilt Insert Color Dimmer R d Shutter econ PL 01 S001 T005 Next Through the key B corresponding to Insert you can add another step in the PlayBack Once added we
24. 5 Then press the key A corresponding to Delete Fix CLEAR BUFFER DMX BASE MEN Delete Menu Delete Fix Delete Chase Fader 01 000 Exit 83 PIE HH HH 9 LightOn Series User Manual WORK had 6 Then you can choose between two options Delete All to delete all stored chases and Delete One To remove only one device Press the key AA corresponding to Delete One mewu Delete Menu Delete One BUFFER e DMX Io Fader 01 000 Exit In 7 Press the select button 1 12 of chase we want to eliminate K sse Press a Preset B DMX Dolte No 8 After selecting the device press the key A for Yes to confirm the device erased of the patch B Delete Chase 1 Active ML mode via the corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup DMX Record BASE Group c 84 LightOn Series User Manual WORK 9 4 Then press the key A corresponding to Delete mew Fixture Menu Delete A BUFFER Fix DMX Auto BASE DMX c 5 Then press the key A corresponding to Delete Chase Fix BUFFER Chase DMX Fader 01 000 Exit In 6 Then you can choose between two options Delete All to delete all stored chases and Delete One To
25. E MODE In this mode each of the faders on the console operates with an specific channel We can only work with 1 scene each time The menu entries are explained above under Setup The examples outlined below are meant to make them one after another starting with the most basic and adding functions gradually Example 1 Switch on channel pairs 1 to 12 1 Press Single Scene being the key in green colour 2 Press the key 1 24 on the left of the faders to ensure we are allocating dimmer channels to the first 24 faders 3 Raise the Grand Master to 100 4 Raise the preset Ato 100 5 Raise faders labeled 1 through 12 to 100 We have turned the 12 pairs You will notice that as we raise the faders 1 through 12 the selection keys are illuminated in green colour Also on display there have been a series of bars indicating the level of each channel mewu Single Scene ragen A o1 MERE BUFFER 13 5 Fader 12 255 In 52 LightOn Series User Manual WORK had Example 2 Switch on the channel pairs 25 to 38 1 press the key 1 25 48 located to the left of the faders to ensure we are assigning the 24 following dimmer channels to faders 2 Raise the labeled faders from 25 through 38 to 100 We have turned the other 12 pairs Have appeared in the display more bars indicating the level of newly activated channels o1 A BUFFER 13 DMX 25 MRR 37 Fade B
26. FER DMX No Exit Free Space BASE 51200K No 6 Press key A corresponding to Yes Dmx Record CLEAR BUFFER Recording TIME 00 00 DMX BASE x lt Pg 01 Record Sub Exit HH vn HUN Mich RH 7 Press key A corresponding to Start When you want to stop de recording process press key D corresponding to Exit 76 LightOn Series User Manual WORK 9 MOVING LIGHT MODE SETUP LightOn console allows the operator to control up to 8 devices of 40 channels each You can store up to 20 playbacks of 99 steps each Each stored step has a fade time and a stand time The LightOn console includes most libraries commercially available devices All of them are stored in the USB memory The ML mode menu has its own submenu then shows a diagram Page 2 Fix Patch Each device can be assigned to a fade preset thus we can select the device quickly via these selection buttons 1 to 12 Thus we use the fader to control the intensity of the device and the select button to select it during programming The main function of patching equipment is to indicate which unit is located in each preset fader and indicate its direction 77 LightOn Series User Manual WORK 9 The steps to patch a fixture are 1 Access the ML mode via the corresponding button Patch BUFFER Setup DMX Record BASE Group C Fader 01 000 E
27. FFER DMX BASE Kul ME Fixture Menu Modify PlayBk P T Invert Memory Lock Fader 01 000 Back WORK H Heek 9 7 By accessing the console will prompt for a password in order to block Introduce the password 168168 via buttons FX1 FX2 FX8 Then press the key D corresponding to Enter to confirm CLEAR BUFFER DMX BASE MRi Memory Lock Exit Memory Lock Password Eug Master 255 Enter 94 HH LightOn Series User Manual WORK 8 Thus the console is completely blocked Pressing the Menu key the console will indicate that is blocked If you wish to unlock press the key A corresponding to Unlock Memory CLEAR BUFFER DMX BASE RH FX Memory Lock Unlock Memory Memory Locked Exit Master 255 HH 9 The console will prompt the administrator password to unlock it Enter the password 168168 through buttons FX1 FX2 Then press the key D corresponding to Enter to confirm CLEAR BUFFER DMX BASE Piel Memory Lock Exit Memory UnLock Password eae Master 255 Enter 95 H FX8 LightOn Series User Manual WORK had USE amp PROGRAMMING Will make the explanation of the use and programming of devices through simple examples These will cover all aspects of use a nd programming the LightOn console To start r
28. Preset B and Preset A faders to down so we will have activated the CrossFade 5 Move the Preset B and Preset A fader to the top position again the stored scene in the submaster 1 is launched so its selection button holds steady in yellow colour and the select button 2 changes to flashing in yellow colour This indicates that the submaster 1 is running and that the submaster 2 is ready 6 Down the Preset A and Preset B fader again 61 LightOn Series User Manual WORK had 7 Raise the Preset B and Preset A faders again as you raise the Preset A and B faders they go fading from the stored scene in the submaster 1 to the stored scene in the submaster 2 Now the select button 2 will stop flashing and stay lit indicating that it is running By contrast the select button 3 will blink in yellow indicating it will be the next to run Thus all Submaster will running in way secuancial way When do CrossFade in submaster mode must be taken into account 1 To stop CrossFade move down the Preset A Fader only and then up Thus we will fade the final output scene 2 When changing the operating mode from Submaster toanother directly we will be stopping CrossFade immediately eliminating the last fade out It is not recommended 3 Any Submaster void or unenforceable will be ignored 4 Any submaster that has been adjusted level manually will be ignored Eg If the fader 1 and 2 are up the CrossFade starts from
29. R Fix DMX Auto BASE DMX c Fader 01 000 Next In 5 Then press the key B corresponding to P T Invert BUFFER Invert DMX Memory Fader 01 000 Back In 92 LightOn Series User Manual WORK 7 With A and key Cs for Pan Normal and Tilt Normal respectively we can adjust the inversion of parameters CLEAR BUFFER DMX BASE FX RH Fixture Menu ran Normal Tilt Normal Fader 01 000 Enter HH 8 Once modified the Pan and Tilt parameters press the key D corresponding to Enter to confirm Memory Lock LightOn console allows the operator to lock the memory of it allowing you to save different configurations and thus prevent unauthorized modification The steps are 1 Activate ML mode via the corresponding buttons 2 Activate the devices we want to change through their respective serlection buttons 1 12 3 Press Menu button 4 Press the key D corresponding to Next as shown in the image below CLEAR BUFFER DMX BASE x RH Fixture Menu Fix Patch Channl Setup Record Group Fader 01 000 Next 93 HH LightOn Series User Manual 5 Then press the key D corresponding to Next CLEAR BUFFER DMX BASE NK Fixture Menu Delete List Fix Auto DMX Fader 01 000 Next 6 Then press the key C corresponding to Memory Lock CLEAR BU
30. RK had LightOn console has a shape generator which gives the operator the ability to create complex effects all quickly and easily A shape is simply a sequence of values which can be applied to any attribute of the device A circular shape for example applied to the pan and tilt attributes would cause the device to move the beam around ina circular pattern you can set the center of the circle the size and movement speed Example 9 Running a Chase Step by Step from Example 6 1 Execute the recorded PlayBack by raising the fader 2 Stop the Chase by pressing PlayBack selection This will turn to yellow colour 4 Press STEP button again to execute the next step 5 Press the selection PlayBack buttonagain This will eliminate manual control HTP channels intensity in the chase shall be controlled by the fader The other channels LTP will be configured asmuch as the fader is moved from zero according to the fade times programmed in the chase We can set the point from which the LPT channels are activated from LIBRARY FIXTURE FILE 100 LightOn Series User Manual WORK had LED MODE LightOn console allows the operator the use of LED devices in the same way as in the ML mode You can create groups edit groups forms or apply effects etc The console can control up to 8 LED units RGBA LED Mode Group CLEAR BUFFER Attrib BASE Shape u D Ka HH X A 000 E
31. Series User Manual Any recorded Submaster can be erased the steps are Deleting a single submaster WORK 1 Access to the Single Scene mode Two Scene or Submaster through their corresponding buttons Submaster Mode Assign Fade CLEAR 01 BUFFER 13 Fade A DMX 25 BASE 37 Fade B T x lt Fader 12 255 RH 2 Press Record button 3 Press key A corresponding to Del Sub as shown in the image below Submaster Mode Del Sub CLEAR 01 BUFFER 13 Del Page DMX 25 BASE 37 Del All Fader 12 255 Piel Exit 4 Press the button for selecting the submaster you wish to remove Del Pg 01 Sub 01 Yes CLEAR 01 BUFFER 43 DMX 25 BASE 37 No RH x lt Fader 12 255 5 Press the key A corresponding to Yes 64 MH H Kl 9 LightOn Series User Manual Erasing a whole page of submasters WORK 1 Access to the Single Scene mode Two Scene or Submaster through their corresponding buttons menu Submaster Mode Assign Fade BUFFER 13 Fade A BASE 37 ade Fader 12 255 2 Press Record button 3 Press key B corresponding to Del Page as shown in the image below mewu Submaster Mode Del Sub BUFFER 13 Page e D BASE 37 All Fader 12 255 Exit 4 Press the button for select
32. With it we can eliminate chases or programs stored in the preset faders 105 9 LightOn Series User Manual A Delete Fixture The steps to remove the patched devices are 1 Activate LED mode through corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below CLEAR BUFFER DMX BASE NEY LED Mode Fix Patch Channel Setup Edit Group Fader 01 000 Next 4 Then press the key A corresponding to Delete CLEAR BUFFER DMX BASE RE LED Menu Mode Delete List Fix Auto DMX Fader 01 000 Next 5 Then press the key A corresponding to Delete Fix CLEAR BUFFER DMX BASE FX Pies Delete Menu Delete Fix Delete Chase Fader 01 000 Next 106 WORK HH Heek HH 9 LightOn Series User Manual WORK had 6 Then we can choose between two options Delete All to delete all LED patched devices and Delete One to remove only one LED unit Press the Delete key A for One mewu Delete Menu Delete One BUFFER e DMX x Fader 01 000 Exit Dp 7 We press the select button LED 1 12 of device you want to delete K sse Press a Preset B DMX Geer No 8 After selecting the LED device press the key A for Yes to confirm the device erase
33. a iaaa 50 LightOn Series User Manual WORK 9 USING AND PROGRAMMING 2 cssccecceseeeeeeeeeeeeeeeeeeeeeee seen eae eaaesaeseaesaessaesaeseaeeeeeeeeeeeeees 51 Operating MOPS oes sscccsies cece aaien a aa a A snd taeued iE EA aS E sendbead n vied codes 51 Single Scene Oe 52 TWO Scene Mode arnore E O a EEE E AAE Aa EEA 56 S bmaster ee 57 Keren ee 63 lee DE 63 E KE DE 67 DIMXBaSE RECOM D 71 Mowing Light Oe EE 77 LED Ae 101 Memory PlayBack Mode esoeneeeeeeseeeesssensresretrnsretrtnestternsresttennstestttnnsttttntnnsttetnn testen nn tenne en 121 Additional Information cccceecceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeees 123 APPENDIX energesch Eege Eed eeg Eech 123 Uibranes ESO geess eege eege dee 123 VGAsCard IIMStAllAtiOn sc ccssecozs c0i ss tateees aaaea anireo on av adeeestaataduestagtagecaeeannayeed 129 Notes about cables and CONNECTIONS 0 ee eee ceeeeee cnet cette eeeeaaeeeeeeeeeeaeeeeeaeeseneeeensaneeenaaes 130 LightOn Series User Manual WORK 9 BEFORE STARTING Contents of the box Cautions Information 1 x LightOn Console Lighton 3 or Lighton 5 1 x Power Supply DC 9 12V 800mA 2A depending on model 1 x User manual To reduce the risk of electric shock or fire do not expose this appliance to rain or moisture Do not spill water or other liquids on the unit Turn off the unit immediately if it detects a malfunction If you detect smoke or unusual odor from the
34. al vm Sa vn Ce 4 Then press the key D again for Next as shown in the image below SW BUFFER VGA DMX Update BASE Dmx Be C C vn ve Ce 5 Then press the key D again for Next as shown in the image below Set BUFFER Set DMX Upload BASE Lib Cc 43 LightOn Series User Manual 6 Then press the key C for Memory Lock as shown in the image below Menu CLEAR BUFFER DMX BASE System Files Change Passwrd Lock Memory RH Master 255 Next WORK MH 9 7 By accessing the console will request a password Enter the password 168168 or the correct in case of previous change through the buttons FX1 FX2 FX8 Memory Lock CLEAR BUFFER DMX BASE Memory Lock Password Exit X Master 255 RH Enter MH In this way the console is completely blocked Pressing the Menu button would indicate that the console is locked If you want to unlock press the key A corresponding to Unlock Memory Memory Lock CLEAR BUFFER DMX BASE Memory Locked Exit RH X Master 255 Enter 44 eek LightOn Series User Manual WORK had The console requests the password administrator to unlock it Enter the password 168168 or the correct if it has been changed previously via the buttons FX1 FX2 FX8 Then press the key D corresponding to Enter to confirm
35. an USB memory 128 LightOn Series User Manual WORK 9 VGA CARD INSTALLATION Here is the procedure to install the optional VGA card in your LightOn console Before proceeding make sure you have found the right tool and you are in a dry and clean place 1 Save all console data 2 Unplug the power cord from the back of the console 3 Remove the screws of the piece that protects the VGA card slot This is located on the rear panel 4 Insert the VGA card carefully making sure that is properly in place and position 5 Fix the screws again 6 Connect the monitor VGA cable to DB15 connector on the card you just installed 7 Reconnect the power cord and turn on the console system 8 Enter to the Menu and go to the VGA SET and active the output 9 If the image on the monitor is offset adjust with the AutoAdjust function that incorporate all monitors Adjust the brightness and contrast levels for the best picture possible 129 LightOn Series User Manual WORK 9 NOTES ABOUT DMX CABLES AND CONNECTIONS Basic notes about DMX 1 In a DMX 512 connection there are 512 channels which can be assigned in any way 2 Any device able of receiving DMX 512 needs a sequential number of channels to be controlled 3 In order to control you must assign each device a starting address which is the same that has been allocated for that device in the control console 4 There are different ty
36. are CLEAR BUFFER DMX BASE FX NEY Menu VGA Set ArtNet Set Upload Lib Master 255 Next Menu System Files Change Passwrd Lock Memory Master 255 Next Menu Assign EXT REV 1 20 Master 255 Back 49 WORK Mu eee HH 9 LightOn Series User Manual WORK had MENU DIAGRAM 50 LightOn Series User Manual WORK 9 USING AND PROGRAMMING OPERATING MODES LightOn console supports up to 6 working modes each mode is set to each of the programming needs control and playback of any event Specific modes are 1 Single Scene Used to work in single scene mode with dimmer channels 2 Two scene Used to work in two scene mode with dimmmer channels 3 Submaster Used to run different scenes in each fader with channels of dimmer These scenes have been previously recorded in the Single and Two Scene modes 4 ML Used to operate robotic devices and moving head sources 5 LED Used to operate devices or LED bulbs 6 MEM Playback Used to play pre recorded scenes in Single Scene Two Scene ML and LED For a better understanding of the operation of each mode we have made examples showing how to use each Then we will detail them in each including a series of exercises and links to examples 51 LightOn Series User Manual WORK 9 SINGLE SCEN
37. ate the Single Mode or Scene Two Scene by their corresponding buttons 4 Press Menu 5 Press the key D for the entry Next as shown in the image below Set Up BUFFER Patch DMX SS we Ce 6 Then press the key B Update for VGA as shown in the image below SW BUFFER VGA DMX Update BASE Dink Bs c C wn we Ce 7 Once inside will press the key D corresponding to Enter to make the copy The update will make automatically Once completed restart the console When turned on again we have a new display 24 LightOn Series User Manual WORK 9 DMX BASE UPDATE Lighton has the ability to store data from an external device to the DMX Base The DMX Base allows us to record or upgrade from an external file To update the DMX Base first copy the corresponding file on the path WORK1248 DMXBASE on a USB stick Steps to follow 1 Connect the USB to the console Lighton 2 Power on the console 3 Activate the Single Mode or Scene Two Scene by their corresponding buttons 4 Press Menu 5 Press the key D for the entry Next as shown in the image below Set Up BUFFER Patch DMX Cm aco So ve Ce 6 Then press the key C Update for Dmx_Bs as shown in the image below SW BUFFER VGA DMX Update BASE Dmx_Bs c C sr ve Ce 25 LightOn Series User Manual WORK 9 7 Once inside enter th
38. bmaster modes without content in ML and LEDs Each FX has a fade time and time single step maximum 99 steps for each FX 6 operating modes Single Scene Scene Two Sub Master Moving Light ML To Moving Head LED and Memory Playback Blackout to shut down all units Memory Playback mode enables a combination of Sub Master mode LED and Moving Light Wireless DMX optional VGA output for monitor 800 x 600 optional LightOn Series User Manual work I Layout LightOn Series User Manual work I FADER AREA It contains 24 physical faders with their respective buttons Single mode and Scene Two Scene by activating the 1 24 assign the first 24 channel faders Conversely when 25 48 turn on a button will be assigned the following 24 channels to the faders In Moving Light ML and LEDs modes each of the selection buttons sis used to select the devices with fixtures or LEDs those who want to work Sub Master mode use each of the faders to launch pre programmed scenes Kat ee eS CDCR Ee Ee CD ee eo LightOn Series User Manual work IY EDITION AREA From the Edition Area we perform the following operations e Switching between the operating mode of the console e Enable or disable devices that do not support DMX e Record e Set fade times e Set the stand time e Perform CrossFade function e Apssgergsantsh Shee 1 2 3 A forrest se fs es p H i lk m Pe Se Ce Biebssgerka
39. bove to activate the scene We can then switch between the 12 submaster pages you just need to hold down the Submaster and then press one of the select buttons 1 to 12 to go to the page you want The same way we can assign a Fade time on each submasters we can assign the Fade A and B Therefore whenever we make a crossfade with Preset A and B faders we will do with certain Fade Time Example 5 Setting Fade A and Fade B 1 Press the Submaster button to access to this mode 2 Press the key B corresponding to FADE A located to the right of the screen 3 Adjust the Fade time of Preset A fade through fader Step Rate 4 Press the key A again to clear the selection 5 Press the key C corresponding to Fade B 6 Adjust the Fade time of Preset B fader through fader Step Rate 7 Press the key C again to clear the selection 8 CrossFade between Preset B Preset A and to see the changes we have made 60 LightOn Series User Manual WORK had Submaster mode Lighton console allows the operator to CrossFade in sequence May fade between each of the Submasters recorded one after another Example 6 Using CrossFade in submaster mode 1 Submaster Press the button to access this mode 2 Check that the Preset B Preset A faders are in the down position 3 Move the Preset B and Preset A faders to the top the selection key number 1 will blink in yellow colour LELAA LEE 4 Move the
40. d of the patch B Delete Chase 1 Active LED mode via the corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup DMX Edit BASE Group c Fader 01 000 Next Dp 107 LightOn Series User Manual 4 Then press the key A corresponding to Delete CLEAR BUFFER DMX BASE kul x lt JBE Led Menu Mode Delete List Fix Auto DMX Fader 01 000 Next 5 Then press the key A corresponding to Delete Chase CLEAR BUFFER DMX BASE x lt rie 6 Then you can choose between two options Delete All to delete all stored chases and Delete One To remove only one chase Delete Menu Delete Fix Delete Chase Fader 01 000 Exit Press the key AA corresponding to Delete One CLEAR BUFFER DMX BASE Er 7 Press the select button 1 12 of chase we want to eliminate CLEAR BUFFER DMX BASE RE 8 After selecting the device press the key A for Yes to confirm the deleted of the chase Delete Menu Delete One Delete All Fader 01 000 Exit Delete Menu Yes Press a Preset lt BUMP gt to Delete No Fader 01 000 108 WORK Hd Mick Hun Huch 9 LightOn Series User Manual WORK had List Fix Fix List function helps the op
41. d or missing accessory do not use and contact your dealer Please read this manual carefully Keep this manual with the unit for future reference NOTE Performance data and controls are common to both Litghton console models The only different features related to the number of channels size and weight are specified in this manual LightOn Series User Manual WORK 9 Functions Professional DMX console ideal for conventional light Moving Heads and LED devices LCD display for easy operation with contrast adjustment USB port for upload download data and software update Artnet port for fast communication between such devices DMX IN with XLR 3 pin connector to connect other external console DMX Output that accepts 2 DMX groups XLR 3 and 5 pin connectors for use with dimmer or other similar devices Backlit buttons that change the color depending on the state Grandmaster fader control all of the output 576 recordable scenes 12 pages x 48 scenes Sub Master mode for conventional lights 1152 for Lighton 5 24 faders for conventional control Moving Head and LED devices 48 for Lighton 5 Controls up to 8 Moving head devices up to 40 channels each 24 for Lighton 5 20 Playbacks of 99 steps each in mode Moving Light mode For Fixture groups Controls 8 LED elements RGBA 24 for Lighton 5 20 playbacks of 99 steps each in LED 12 FX mode embedded with content already recorded on Single Scene Two Scene and s u
42. de BUFFER Fade A 13 BASE a Io Fader 12 255 In To record a submaster we should be in Single Scene or Two Scene The process is fast and simple just record from either mode and switch to submaster mode to run stored scenes Example 1 Recording a submaster 1 Select mode Single Scene or Two Scene 2 nd We make sure to have the 100 GrandMaster 3 Raise the preset faders 4 Adjust the level of the desired channels eg turn up the fader 1 2 and 3 5 Press Record the selection buttons for each channel will flash in red colour 6 Press the channel selection button where you want to save the scene eg 1 7 Look at the display and check how the recording process starts once finished the red colour buttons will turn off again leaving in green the channels that we have adjusted the levels 8 Raise all channels to 0 9 Click on submaster to access this mode 10 Raise the fader 1 where we recorded above to activate the scene channel select where you want to save the scene eg 1 7 th We look at the screen and starts veemos how the recording process once the eye buttons will turn off again leaving green channels that we have adjusted the levels 8 th We got all channels to 0 9 th click on submaster to access this mode 10 Raising the fader 1 where we recorded above to activate the scene 57 LightOn Series User Manual WORK had If you look at the 8th step we have
43. e since it can activate the VGA output which show us real time information about the status of the playbacks scenes channels effects submasters and presets as shown in the image below SUBMASTER j PRESET EFFECT OU To access to VGA card adjustment the steps are 1 Power on the console 2 Activate the Single Mode or Scene Two Scene by their corresponding buttons 3 Press Menu 29 LightOn Series User Manual 4 Press the key D for the entry Next as shown in the image below Set Up BUFFER Patch DMX Io A 000 Totes Next 5 Then press the key D again for Next as shown in the image below SW BUFFER VGA BASE Dmx_Bs A 255 TI Next 6 Then press the key A for VGA Set as shown in the image below Set BUFFER Set DMX Upload BASE Lib Master 255 Next 7 Once inside you can select from three options 1 Press the key A for Open to activate the output to VGA 2 Press the key B for Close to disable the output to VGA 3 Press the key D for Exit to exit this function 30 WORK HH HH MH 9 LightOn Series User Manual BASE RH vga Enable Set Open CLEAR If you select BUFFER OPEN Close DMX will Reboot Exit FX Master 255 WORK MH By selecting the Open option the console will reboot and when start on the monitor can see the cons
44. e channels adjustment press key D corresponding to Enter At any time you can leave this page by pressing he Menu key Thus we have defined from which channel will be patched the different devices supported by LightOn console Edit Group LightOn console allows the operator to create groups of equal LED devices and can select multiple devices at once The steps to record a group are 1 Activate LED mode via the corresponding buttons 2 Activate the devices you want to include in the group through its select button 1 to 12 104 LightOn Series User Manual 3 Press Menu 4 Press the key C corresponding to Record Group as shown in the image below CLEAR BUFFER DMX BASE FX RH 5 The display shows a message indicating that we select one of the selection buttons 1 12 which will be flashing in blue colour Thus it will include selected LED devices in the same group CLEAR BUFFER DMX BASE RE Fixture Menu Fix Patch Channel Setup Record Group Fader 01 000 Exit Edit Group Record Group Select a Bump as a Group Fader 01 000 Exit WORK HUE MH 6 Press a selection button 1 to 12 The buttons will stop flashing and we will have recorded the group Delete In LED mode the LightOn console has two deleted fuctions A Delete Fixture With it we can remove the patched devices B Delete Chase
45. e password 168168 through the buttons FX1 FX2 FX8 mew Update software e CLEAR l Insert USB Password DMX A 255 T Enter Dp 8 After entering the password press the key D corresponding to Enter to access the USB drive We press on Enter again and the updated will done automatically For this function we used a conversion software to convert a flash file Swf in DMX frame Thus the console may use this data to create effects on LED devices for example Using conversion software Lemon 512 Along with the console there is provided a software installer that contains the Flash Convert Lemon 512 so it will be necessary a computer with Microsoft Windows for installation Once installed run it and in the desktop appears the program as shown in the image below Le Lee S07 Flach Cee Ver 1 00 Mare ree D Leg Ee LT ne 26 LightOn Series User Manual WORK I Becoming swf files to scn The LightOn console accepts swf files after being processed into a scn files To perform this conversion charge a Flash file format swf by pressing the button Open Flash so will open a window where you can select the file you want to load as shown in the image below Legare Hasie E Desking oco Dyah kiria E Zi 2348 After selecting the file click Open so we loaded our file conversion within the software mF if mee F rh ere ee 1 arb He
46. e select key 1 and held down 7 Press the select key 4 Example 2 Controlling the devices 1 Select LED mode 2 Make sure to have the Master at 100 3 Activate the devices 1 2 3 and 4 through the selection keys 1 12 4 Raise the fader of LED devices 1 2 3 and 4 to increase the intensity 5 Raise the fader Red fader number 45 to see bright red LED devices 6 Raise the fader green Green fader number 46 to add to the color green LED devices 7 Raise the fader Blue fader number 47 to add the color blue LED devices Example 3 Changing the attributes of the devices from Example 2 1 Press the key B corresponding to Attrib 2 Select the attribute you want amending 3 Return to the fader Attrb fader number 48 We have assigned a new attribute to control 117 LightOn Series User Manual WORK 4 Raise the Attrb fader and see how change the attribute assigned CLEAR 02 Santa Sen BUFFER 1 Red 127 d 2 Green 064 DMX Example 4 Recording a PlayBack from Example 3 1 Press the key Record 2 Press any PlayBack selection buttons 13 to 20 To select the playback 3 Press the button again to select Playback To save the step 4 Press the ClearBuffer key 5 Press the button Record To stop recording 6 Raise the fader PlayBack to finish the record As you can see we have pressed the ClearBuffer button when we finished recording the C
47. eck the ASSIGN FADE WORK 9 Press the keys B and C for Page Up and Page Down respectively to configure the Submaster paging 10 In Mem PlayBack mode can switch to another mode by pressing the corresponding key The display will show what following Mem PlayBack CLEAR Exit PlayBack BUFFER Intro SUB MASTER DMX BASE Yes No RH FX P 01 Select 1 12 BEE 11 press the key A for Yes to change modes or press the key C for No to remain in Mem PlayBack mode 122 9 LightOn Series User Manual work I APPENDIX LIBRARIES EDITION iF you can not find the library for the used devices uand you want to create or you want to know how to create a custom ML bank this section will explain Along with the LightOn console we supply software for editing and creating libraries for your console To use the LightOn Edit Library software you need a PC with Microsoft Windows Once installed you can create your own libraries a H a a a a a a a o a a a D Before you start editing your custom library make sure you have your channel list and technical specifications of its LED or Moving Head device 123 LightOn Series User Manual work I Steps to follow 1 Start by indicating the properties of the device ee Humber oi Channels fie Me TitDegwe 270 2 Define the channels of the device t 0 0 y i H H 0 D 0 a
48. ed to record presets and scenes EXT 1 EXT 2 EXT 4 On Off keys 12 LightOn Series User Manual WORK had Key A Key B Key C Key D Keys for programming A B C y D Used to navigate through console menus e Menu This key is used to program each parameter and to enter or exit of the menu e FX Push this key the keys FX 1 12 are avaible in FX mode Clear Buffer Clean ongoing operations DMX Base Push this key Chase 1 12 will be in FX mode 99 steps per chase and 12 chases can operate synchronously FD ST TIME The fade time FD is enabled when the indicator is red The stand time ST is available when the indicator is yellow e STEP Used to configure the steps in FX 1 12 GO STOP Used to start ans satop the FX 1 12 play e SOLO It means if keys 1 12 has SOLO function or not FADERS 1 Fader 1 Fader 2 Fader 3 Fader 24 Refer to 1 2 3 24 If you choice key 25 48 the channels will be 25 25 27 48 2 Preset A and Preset B Scene control fader for Preset A yand Preset B 3 Flash level The Flash key value in the output 4 Step Rate Used to configure the play time for FX 5 Grand Master Main control for HTP values in DMX channels 13 LightOn Series User Manual WORK had CONNECTIONS hw i m Dmx out m Dmx our K rower WORK Y A B sa aii E Cl me CC 1 PDC IN Port Connect the external power supply with a max of 9 12 V DC 2A 2 ArtN
49. el in the console Steps to follow 1 Activate the Single Mode or Scene Two Scene by their corresponding buttons 2 Press Menu 3 Press the key corresponding to B DMX Patch as shown in the image below Menu CLEAR BUFFER DMX BASE Channel Set Up DMX Patch LedSet A 000 RE Next 17 H LightOn Series User Manual WORK 9 4 Once inside press the key A corresponding to Chan Patch Patch BUFFER Patch DMX Cm s Ce 5 Upon entering wit appears the next window which indicates that the Channel 1 in the console controls only channel 1 Dmx mewu adress Patch Up A ae Patch By Cha gt 01 ZER gt 01 gt x Fader 01 000 Enter In 6 By pressing C corresponding to gt we can move and change between the console channel and the different DMX channels yp g p g g Use the keys A and B for UP and Down respectively to adjust the values Thus we can make a configuration as shown below CLEAR l Patch By Cha gt 01 BUFFER Dimmer Down 001 002 003 ur oos e E BASE 007 008 009 z C 7 Once the relevant changes will press the key D Corresponding to Enter to save them Now when we get console channel 1 we will be controlling dimmer channels 1 to 9 from the same Fader 18 LightOn Series User Manual DMX Patch In this way we will be assigning a channel to a c
50. emory Lock Memory Lock Exit Master 255 Enter 115 WORK Hd Heek HH MH 9 LightOn Series User Manual WORK 8 Thus the console is completely blocked Pressing the Menu key the console will indicate that is blocked If you wish to unlock press the key A corresponding to Unlock Memory CLEAR BUFFER DMX BASE X RH Memory Lock Unlock Memory Memory Locked Exit Master 255 eek 9 The console will prompt the administrator password to unlock it Enter the password 168168 through buttons FX1 ES Then press the key D corresponding to Enter to confirm CLEAR BUFFER DMX BASE X RH Memory Lock Exit Memory UnLock Password Less Master 255 Enter 116 BEE FX8 LightOn Series User Manual WORK 9 USE AND PROGRAMING We will explain the use and programming of LED devices through simple examples these will cover all aspects of using and programming the LightOn console We start repeating the patch example previously seen in the ML mode NOTE The examples are designed to perform them consecutively Example 1 patching 4 consecutive LED devices 1 Select LED mode Press Menu button 3 Press the key A for FixPatch 4 Move between different LED devices and select one 5 Press the key D corresponding to Enter to select the appliance 6 Press th
51. epeat the previos patching example NOTE The examples are designed to perform them consecutively Example 1 patching 8 consecutive devices 1 Select ML mode 2 Press theMenu button 3 Press the key A for FixPatch 4 Press the key C for More 5 Continue pressing the key C for More to see Work in the display 6 Press the key B for Next to select Work 7 Press the key D corresponding to Enter 8 Press the key D corresponding to Enter to select the appliance WKB572C1 9 Press the select key 1 and held down 10 Press the select key 8 Example 2 Controlling the devices 1 Select ML mode 2 Set Master to 100 3 Activate the devices 1 2 3 and 4 through the selection keys 1 12 4 Raise faders of 1 2 3 and 4 fader to increase the intensity 5 Raise the fader Attrb fader number 48 until the shutter is opened 6 Adjust the Pan of the devices using fader Pan fader number 45 7 Adjust the Tilt of the devices using fader Tilt fader number 46 8 Change the colour of the devices by Color Fader fader pins number 47 96 LightOn Series User Manual WORK 9 Example 3 Changing the attributes of the devices from Example 2 1 Press the key C corresponding to Attrib 2 Select the attribute you want to modify eg Gobo 3 Return to fader Attrb fader number 48 now no longer controls the shutter have assigned a new attribute to control 4
52. equipment stop using and unplug it Do not open the unit No items for the user control inside Do not dismantle or modify the unit void the warranty Never try to repair it Repairs by unqualified persons may cause damage or malfunction Contact with an authorized service Keep dry the unit This product is not waterproof and can malfunction if is exposed to high levels of moisture The internal oxidation can cause damage Do not hit it This product may malfunction if it is subjected to strong shock and vibration Keep away from strong magnetic fields Not use or place the unit near equipment that generates strong fields of electromagnetic radiation or magnetic fields Heavy loads of these fields as radio transmitters can interfere with the display or affect the internal circuitry of the product Cleaning Due to the residues of smoke or dust to clean the outside of the unit is necessary Use a glass cleaner conventional and a soft cloth Copyright None part of this user manual may be reproduced transmitted transcribed stored in any system or translated into any language in any form or medium without permission LightOn Series User Manual WORK I Specifications Power Supply DC 9 12V 2A Max Chassis Electrolytic Plate with powder finishing LCD 60 x 128 dots LCD TFT display with contrast adjustment Inputs Outputs e DMX IN Neutrik XLR Connector e DMX OUT Neutrik XLR 3 amp XLR 5 Connectors e POWER SUPPLY Connected t
53. erator to see easily neatly and clearly the assigned LED devices and their corresponding DMX address The steps for using the Fix List are 1 Active LED mode via the corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup BASE Group Io Fader 01 000 Next In 4 Then press the key B corresponding to List Fix mewu Led Menu Mode Delete BUFFER Fix DMX Auto BASE DMX C Fader 01 000 Next In 5 The display shows the patched devices and their address We will use the key D corresponding to More for move between them CLEAR Num Device DMX BUFFER 01 XBanDa gt 053 02 lt Empty gt DMX 03 lt Empty gt 109 LightOn Series User Manual WORK 9 Auto DMX LightOn console allows the user to auto address the assigned LED devices automatically The steps to use the Auto DMX are 1 Active LED mode via the corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup BASE Group Io Fader 01 000 Next In 4 Then press the key C corresponding to Auto DMX mewu Led Menu Mode Delete BUFFER Fix DMX Auto BASE DMX Fader 01 000 nen 5 Then press the key A for Yes to auto patch them sequentiall
54. erform the following steps 1 Acced to Single Scene or Two Scene modes with their corresponding buttons 2 Press the Record key Sub BUFFER 13 Page BASE 37 All x Fader 12 255 Exit In 3 Press the corresponding key to Fx we want to edit The button will light in blue colour and the display will show the following Step BUFFER FxBase 13 ase Gr Next C 4 Now we can to edit the Fx 68 LightOn Series User Manual If we want add a scene before any other step we will use C and key Ds for Next and Back respectively to select the step where we want to insert the scene and then press Step button to insert it will before that step Fade and Stand time a in Fx At each step of each Fx can be assigned a Fade and Stand time The steps are 1 Access to Single scene or Two Scene modes through their corresponding buttons 2 Press record key Submaster Mode CLEAR 01 BUFFER 13 DMX 25 BASE 37 Del Sub Del Page Del All x lt Fader 12 255 REN Exit 3 Press the key corresponding to Fx we want to edit The button will light in blue and the display will show the following Submaster Mode CLEAR 01 BUFFER 13 DMX 25 BASE 37 Del Step Del FxBase Next x lt RH Fx 01 S amp 000 _ T 000 Back 4 Move between steps with keys C a
55. et Port Allows communication with ArtNet compatible devices 3 USB Port Connect an USB memory to manage files or download updates 4 VGA Port Show the operation of the unit in a screen with de 800x600 pixels resolution Optional card 5 DMX IN Port Connect to receive DMX signals 6 DMX output ports Port A Output for DMX signal from DMX base Port B Output for DMX signal to the next console 14 LightOn Series User Manual WORK 9 USING INSTRUCTIONS Setup Channel configuration Lighton console supports 512 DMX channels in which we can patch any moving head LED or dimmer therefore before patch we define which channels correspond to each type of device This will facilitate patching equipment later Steps to follow 1 Activate the Single Mode or Scene Two Scene by their corresponding buttons 2 Press Menu 3 Press the corresponding key to the Channel Setup input A as shown in the image below Set Up BUFFER Patch DMX BASE LedSet Cc A 000 KE Next In 4 Once inside you will see the allocation of channels divided into 3 groups Dim Dimmer Led for LED devices and ML For Moving Heads Start End gt ES BUFFER Dim gt 001 048 Own Led 053 153 BASE ML 154 512 S 15 LightOn Series User Manual WORK had 5 With the key C corresponding to gt we can move through the values With the keys A and B Up a
56. g us Once located the device selected it by the key D for Enter ix BUFFER To DMX 004 DMX Press Bump BASE Button to Patch C x Fader 01 000 Exit In 5 The selection buttons 1 12 will start flashing in red colour and the display will show two options we can choose another device through the key A or exit through the key B If we want to change the DMX allocation we can use the FX1 FX2 FX10 to assign specific DMX address 6 Press a selection button 1 to 12 The unit will be patched on the selected fader preset Channel Set Up Thus we will definy from which channel will be patchede each of the different type of devices that Lighton console supports Steps to follow 1 Activate the LED mode via the corresponding buttons 2 Press Menu button 3 Press the key C corresponding to Channel Setup as shown in the image below Patch BUFFER Setup BASE Group x Fader 01 000 Exit In 103 LightOn Series User Manual WORK had 4 Once inside you will see the allocation of channels divided into 3 grupos D im Dimmer Led For LED lights or bars and ML For Moving heads Start End om CX BUFFER Dim gt 001 048 own BASE ML 154 512 S 5 With the key C corresponding to gt you can move through the values With the keys A and B Up and Down respectively you can adjust the values 6 Afterfinished th
57. ger PS Co ole Corer eer pea ie SA a i eng Meder ty a a gt Lic hoa samipi SES TH el 27 LightOn Series User Manual WORK had After loading the file to convert click the button FileConvert when clicked will appear a window where you can adjust the Frames per second of the export file The value of frames per second can be adjusted from 1 to 35 frames S Lego TEE h u Ke mm bmm hipag pa a d ae ze Pane Lem F bg soe Teen laps D i im Lei ask Frees f E ie m C p ha IS Ba Sa ST B After setting the value of Frames S click OK and give the name of the Scn file that we create once assigned the name press Save do ali dees Bemis PLA H eai P Desar Rea lebt e E Veto O Te Som l Baris Miia S Den mied ES Ldb r EEEE DaT 1 s After the conversion copy the created Scn file to a USB memory in the path WORK1248 DMXBASE Now we can connect the USB to DMX console and update the Base from the MENU 28 LightOn Series User Manual WORK 9 VGA card adjustment Before you can access this feature you must have done the following 1 You have installed a VGA card optional in the Lighton console as shown in the appendix that accompanies this manual 2 Have downloaded the VGA images as detailed in the Update VGA_P If all the above operations have been carried out correctly we can access this featur
58. hase Otherwise when we were to run would overwrite the Chase and not run properly Example 5 Recording steps in a PlayBack from Example 3 1 Press the key Record 2 Press any PlayBack selection buttons 13 to 20 To select the playback 3 Press the button again to select Playback To save the step 4 Modify the R G and B values 5 Press the button again to select Playback To save the step 6 Assign a different function to Attrb fade and change the new atribut 7 Press the button again to select Playback To save the step 118 9 LightOn Series User Manual WORK 9 8 Press key ClearBuffer 9 Press the button Record To stop recording 10 Raise the PlayBack fader we ve recorded This time we have recorded a series of steps in the PlayBack As we added steps the display indicates that step have recorded and in which PlayBack mew Record PlayBack Focus Sr 02 XBanDa G BUFFER 1 Red e 2 Green 064 DMX Blue 3 Blue 012 Attrib x Fader 45 127 New p When you push the RECORD button the selection buttons for PlayBack that are empty flash On the contrary playbacks in which we recorded previously the selection button is off and can not be selected In this exercise we have allocated Fade time or Step time to each of the steps so that the playback will go running as a Chase The steps will be running one after another quickly Exa
59. heir corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Set Up BUFFER Patch DMX BASE LedSet Cc A 000 Pen Next In 4 Press the key D corresponding to Next again as shown in the image below SW BUFFER VGA DMX Update BASE Dmx Bs c CS 36 LightOn Series User Manual 5 Press the key D corresponding to Next again as shown in the image below Set BUFFER Set DMX Upload BASE Lib Master 255 Next 6 Then press the key A for System Files as shown in the image below Files BUFFER Passwrd BASE Memory Master 255 Next WORK HH HH 7 By accessing the console will request a password to perform file import We introthe password 168168 via buttons FX1 FX2 FX8 mew System Files Exit CLEAR l Insert USB Password DMX BASE eee eee A 255 TI Enter 8 Once inside you can select from 4 options HH 1 Press the key A for System Download to import the entire library system from a USB memory 2 Press the key B corresponding to Fix Download to import the libraries of the devices from a USB stick 37 9 LightOn Series User Manual WORK had 3 Press the key C corresponding to SubMst Download to import the information stored in the Submaster from a USB stick 4
60. ing that it is selected and is running 5 Press the GO STOP button again to stop the chase This will light in solid red as before LightOn console allows the operator to run 12 Fx simultaneously 70 LightOn Series User Manual WORK had DMX_BASE RECORD LightOn console allows the operator to record DMX data from an external device This feature can be very useful in certain circumstances In DMX_Base Record function can choose from 4 options 1 BBT Recording The console starts and stops recording automatically 2 DMX Recording The console requires a confirmation to start recording and stopping 3 Del Base To delete the data stored on the selected FX1 FX2 FX3 FX12 4 Del BASE ALL To delete all data stored on all buttons FX1 FX2 FX3 BBT Record We can choose between two options SES buttons Fx12 A AUTO Record When all the DMX values are 0 the console is ready to record when there are values that are not 0 the console automatically begins recording Recording stops autonomously when DMX values back to 0 B MANUAL Record When all the DMX values are 0 the console is ready to record When you press Start the console starts recording The recording stops autonomously when DMX values back to 0 A The steps are as follows for using the AUTO Record 1 Access to Submaster mode via the corresponding button Submaster Mode CLEAR 01 BUFFER 13 DMX 25 BASE 37
61. ing the submaster page you wish to remove BUFFER 13 e N BASE 37 o Pg 01 Record SubMaster 5 Press the key A corresponding to Yes 65 Cc HH MH HH 9 LightOn Series User Manual Complete removal of all submasters WORK 1 Access to the Single Scene mode Two Scene or Submaster through their corresponding buttons Submaster Mode Assign Fade CLEAR 01 BUFFER 13 Fade A DMX 25 BASE 37 Fade B Fader 12 255 JEBE 2 Press Record button 3 Press key C corresponding to Del All as shown in the image below Submaster Mode Del Sub CLEAR 01 BUFFER 43 Del Page DMX 25 BASE 37 Del All Fader 12 255 Jel Exit MH HH 4 The display will show a window to confirm the delete process of al submasters stored on the console mew Del All Sub gi BUFFER 13 e N o BASE 37 Pg 01 Record SubMaster 5 Press the key A corresponding to Yes 66 HH 9 LightOn Series User Manual WORK 9 FX 1 12 RECORD LightOn console allows the operator to store up to 12 Fx from SingleScene and TwoScene modes Each of the effects recorded will work as a Chase and can store up to 99 steps The steps for recording a Fx are 1 Acces to Single Scene or Two Scene mode through their corresponding buttons 2 Press Record key
62. mple 6 Recording steps in a PlayBack with Fade and step time from Example 3 1 Press the key Record 2 Press any PlayBack selection button 13 to 20 different from the example above To select the PlayBack 3 Press the button FD ST TIME leaving it red colour To adjust the fade time 4 Adjust the Fade time through the fader STEP RATE 5 Press the button FD ST TIME again leaving it in yellow colour To adjust the step time 6 Press the Playback selection button again To save the step 7 Modify R G and B values 8 Press the FD ST TIME button leaving in red colour To adjust the Step time 9 Adjust the Fade time through the fader STEP RATE 119 LightOn Series User Manual WORK 9 10 Press the button FD ST TIME again leaving in yellow colour To adjust the step time 11 Press the Playback select button again To save the step 12 Press the ClearBuffer button 13 Press the Record button to end recording Running the recorded PlayBack we check the steps will follow one another according to the fade time and step we have assigned Example 7 Using Shape figures generator from example 3 Press the Menu key to exit the Attrb 2 Press the key C corresponding to Shape 3 Press any key A B and C corresponding to Rainbow Knight Rider and Chase Eg Rainbow 4 Adjust the parameters of Item Set DirBy Set and Color Set by the A B and C respec
63. n the PlayBack As the added steps the display will indicated what step and in what PlayBack has been recorded menu Modify Playback Focs Pan CLEAR Color eae ua PL 01 S001 T005 Nex In When we have pressed the RECORD button the PlayBack selection buttons that are emptywill flash On the contrary playbacks in which we recorded earlier the selection button is off and can not be selected In this exercise we have not assigned Fade and Step timesto each of the steps so the PlayBack will running as a Chase The steps will be running one after another quickly Example 6 Recording steps in a PlayBack with Fade and Step times from Example 3 1 Press record key 2 Press any selection PlayBack button 13 to 20 different from the example above To select the PlayBack 3 Press the FD ST TIME button leaving it in red colour To adjust the fade time 4 Adjust the Fade time through the STEP RATE fader 5 Press the FD ST TIME button again leaving it inyellow colour To adjust the step time 6 Press the selection PlayBack button again To select the PlayBack 7 Modify the Pan position Tilt and color 8 Press the FD ST TIME button leaving it in red colour To adjust the fade time 98 LightOn Series User Manual WORK 9 9 Adjust the fade time through the STEP RATE fader 10 Press the FD ST TIME button again leaving it in yellow colour To
64. nd B and press Next to choose another scene i 7 Move the channel faders to adjust the channel levels corresponding to the scene B For example we down to 0 channels 1 to 12 and raise from 13 to 24 at 100 8 Move the Preset A and B fader so we alternated between stage A and B 9 Raise the Preset Faders A and B to the top again and press the key NEXT again to exit the Next function 54 9 LightOn Series User Manual WORK had Example 5 Switching between modes through CrossFade In this example we show how we can smoothly switch from ML LED Single Scene or Submaster modes For this example we assume that we are in either of these ways for example LED 1 Press the key Single Scene This will light IN yellow coloUr 2 Move the Fader Preset A and B to the top if you are above the descend and raise gently again during this process the Single Scene key blinks in yellow colour 3 At the top position with the Fader Preset the Single Scene button stops flashing and will switch to green softly Example 6 Changing between modes directly In this example we show how to switch between ML LED or submaster directly For this example we assume that we are in either of these ways for example LED 1 Press the Single Scene key It lits in yellow green colour 55 LightOn Series User Manual WORK 9 TWO SCENE MODE Two Scene mode is adapted from Single Scene mode the only difference i
65. nd D for Next and Back Select a step 5 Press the key FD ST it must be lit in red colour Thus we can adjust the fade time WORK HH MH Record FxBase Record FxBase Del Step 01 Del 13 FxBase 29 Next 37 Fade Time 2 00 Back 01 13 25 37 Del Step Del FxBase Next Fade Time 7 00 Back SD ST TIME button is in red colour 69 SD ST TIME button is in yellow colour LightOn Series User Manual WORK 9 6 Adjust the Fade time using the fader StepRate 7 Press the button FD St again this will lii in yellow Thus we can adjust the Step time 8 Adjust theStep timeusing the StepRate fade 9 Press the lighted FX button in blue colour again to finish 10 Press the Record button to exit Launch and Use the Fx After the scenes recording and FX the FX1 FX2 Fx12 buttons containing data will lit in red colour Thus we can distinguish that FX have stored scenes or that are empty To activate the steps are the following 1 Access to Single Scene Scene Two or Submaster modes through their corresponding buttons 2 Press the Fx button you want to execute This will lit in yellow indicating it is selected 3 Press the GO STOP button to launch the Fx This willflash in red indicating that it is running 4 Press the Fx button that are running again This will flash in yellow indicat
66. nd Down respectively can adjust the values 6 After adjusting channels push key D corresponding to Enter At any time can leave this page by pressing the Menu key Thus we have defined from which channel the patch will start on the different types of devices that Lighton console supports In the example has been allocated 48 channels for dimmers in particular from channel 1 to 48 DMXPatch Through DMX Patch menu we can make the appropriate settings to the DMX channel or vice versa from DMX to Channel Steps to follow 1 Activate the Single Mode or Scene Two Scene by their corresponding buttons 2 Press Menu 3 Press the key corresponding to DMX Patch B as shown in the image below Channel Set Up BUFFER Patch DMX A 000 T Next Menu i i HH 16 LightOn Series User Manual WORK 4 Once inside you can select between channels assigned to DMX by pressing A Corresponding to ChannelSet Up or on the contrary to assign the DMX channels by pressing the key B Corresponding to Dmx Patch address Patch CLEAR BUFFER DMX BASE Chan Patch DMX Patch Default x A 255 T RH H 5 If on the contrary we simply want to erase any previous mapping settings and restore the default values press the key C for Default Channel Patch In this way we will be assigning one or mutipleDMX channels to a single chann
67. o an external power supply e USB USB connection for data upload download and software updates e Art Net Art Net connection for fast communications between compatible devices Dimensions 482 x 264 x 61 5 mm Lighton 3 718 x 264 x 61 5 mm Lighton 5 Weight 4 1 kg Lighton 3 6 5 kg Lighton 5 Accesories e AC DC External Power Supply included e Output for VGA 800 x 600 monitor optional e Wireless DMX optional VGA Card Optional Sold separately Reservados todos los derechos Las mejoras y cambios en las especificaciones y dise o en este manual pueden ser realizas sin previo aviso LightOn Series User Manual WORK had INTRODUCTION Congratulations on your purchase of a Lighton Series control console This is a compact versatile and powerful lighting console LightOn 3 It incorporates the following configuration 24 faders for conventional control control up to 8 group of 40 fixture channels each and 8 LED devices LightOn 5 It incorporates the following configuration 48 faders for conventional control control up to 24 ML fixtures up to 40 channels each and 24 LED devices 20 playbacks x 99 steps on each mode ML and LED 1152 recordable scenes Each unit has been thoroughly checked and packed before packaging Unpack the unit carefully retain the carton and packing materials for possible future use Check that the product is not damaged and that incorporates all accessories If the product appears damage
68. ocation of channels divided into 3 grupos Dim Dimmer Led For LED lights or bars and ML For moving heads d Channel Set Up Up Start End gt BUFFER Dim gt 001 048 owm Led 053 153 BASE ML 154 512 7 Fader01 000 Enter 5 eel 5 With the key C corresponding to gt can move through the values With the keys A and B Up and Down respectively can adjust the values 6 After finish the channel adjustment press key D corresponding to Enter At any time can leave this page by pressing the Menu key Thus we definy from which channel will be patched each of the different types of devices which supports Record Group LightOn console allows the operator to create groups of identical devices and can select multiple devices at once The steps to record a group are 1 Activate ML mode through correspondinf buttons 2 Activate the devices you want to include in the group through its select button 1 to 12 3 Press Menu button 81 LightOn Series User Manual WORK 9 4 Press the key corresponding to Record Group as shown in the image below Patch BUFFER Setup DMX Record BASE Group c 5 The LCD displays a message indicating that we select one of the selection buttons 1 12 which will be flashing in blue colour Thus we will include the selected devices in a group Record Group B BUFFER Select a Bump DMX
69. ole output ARTNET OUTPUT SETTING ArtNet setup allows the user to use the following options 1 OpPoll 2 ArtNet Config 3 View device OpPoll Used to detect the presence of otherArtNet devices in the network ArtNet Config Used to set the ArtNetnetwork View Device Used to detect the device on the ArtNet network To access the ArtNet connection setting the steps are 1 Power onthe console 2 Activate the Single Mode or Scene Two Scene by their corresponding buttons 3 Press Menu 31 9 LightOn Series User Manual 4 Press the key D for the entry Next as shown in the image below CLEAR BUFFER DMX BASE F RH Menu Channel Set Up DMX Patch LedSet A 000 T asa Next 5 Then press the key D again for Next as shown in the image below CLEAR BUFFER DMX BASE RE Menu Update SW Update VGA Update Dmx_Bs Next 6 Then press the key B corresponding to ArtNet Set as shown in the image below CLEAR BUFFER DMX BASE X Pies Menu VGA Set ArtNet Set Upload Lib Master 255 Next 32 WORK HH HE MH 9 LightOn Series User Manual WORK 9 7 Once inside you can select from four options SubSw Status Disable Set BUFFER Sub switch 01 Univer DMX Universe 01 BASE Enable C P 01 Select 1 24 Disabl In
70. oncrete DMX channel in the console Steps to follow 1 Activate the Single Mode or Scene Two Scene by their corresponding buttons 2 Press Menu 3 Press the key B corresponding to Dmx Patch as shown in the image below Menu CLEAR BUFFER DMX BASE Channel Set Up DMX Patch LedSet X A 000 rie Next 4 Once inside press the key B corresponding to DMX Patch address Patch CLEAR BUFFER DMX BASE Chan Patch DMX Patch Default RH X A 255 T 19 WORK HH MH 9 LightOn Series User Manual WORK had 5 Upon entering wit appears the next window which indicates that the Channel 1 in the console controls only channel 1 Dmx Patch By Dimmer CLEAR D gt 001 C 01 Down DMX gt 6 Using the key C corresponding to gt we can move and change between the console channel and the different channels Use the keys A and B for UP and Down respectively to adjust the values Thus we can adjust that dimmer channel 3 will be controlled from the console channel 2 as shown in the image below Patch By Dimmer CLEAR D gt 003 C 02 Bow DMX gt Fader 01 000 Enter In 7 Once the relevant changes will press the key D Corresponding to Enter to save them Now when we get console channel 2 we will be controlling dimmer channel 3 instead of channel 2
71. onding to Yes CLEAR BUFFER DMX BASE x RH 8 Press key A corresponding to Start CLEAR BUFFER DMX BASE Piel BBT Record Start Recording TIME 00 00 Pg 01 Record Sub Exit BBT Record Recording TIME 00 00 Pg 01 Record Sub Exit When you want to stop de recording process press key D corresponding to Exit DMX Record The steps are as follows for use DMX Record function 1 Access to Submaster mode through its corresponding button CLEAR BUFFER DMX BASE FX RH Submaster Mode 01 13 25 37 Assign Fade FadeA Fade B Fader 12 255 75 WORK Hd Hr HH 9 LightOn Series User Manual WORK 9 2 Press Record button mew Submaster Mode Del Sub BUFFER 13 Page T BASE 37 All Fader 12 255 Exit 3 Press DMX BASE key located in the left side of the display It will lit in blue colour 4 Press any Fx1 Fx2 Fx3 Fx12 button This button will flash in pink colour mew Record DMX Base BBT Record CLEAR A BBT RECORD Dmx BUFFER B DMX RECORD Record C DEL BASE 01 ie D DEL ALL BASE Delete BASE Base Recording EXIT Pg 01 Record Sub DEL All 5 Press key B corresponding to DMX Record Pg 01 Record Sub mew Record DMXBase Yes CLEAR Ee BUF
72. pes of devices with different numbers of channels We must take this into account when addressing the apparatus so as to avoid overlapping the devices between them This would cause malfunction It is advisable to plan addressing before assigning to each appliance start a channel 5 DMX devices are designed to receive a DMX signal chain so you have a DMX IN connector and a DMX OUT connector 6 The order in which the units are connected is not important each device will respond only to the orders of the channels have been assigned 7 DMX devices can be connected via XLR or XLR 3 5 male female 8 The wiring of the devices must be made with shielded twisted pair lines 9 In the last apparatus of the chain must be closed by a load line This reduces signal errors and avoids possible problems and interference Connection XLR 3 130 LightOn Series User Manual WORK 9 Final Load It is done through a resistance of 120 Ohms 1 4 W between pin 2 and pin 3 of the last device in the chain 3 to 5 pin converter LightOn console has both inputs and outputs 3 and 5 pin does not require any type of conversor However in case you need it the correspondence is as follows CONDUCTOR XLR 3 OUT XLR 5 IN 131 EQUIPSON S A Avda El Saler 14 Pol Ind L Alter6 46460 Silla Valencia Spain Tel 34 96 1216301 Fax 3496 120 02 42 www equipson es equipson equipson es
73. ponding to Shape 11 To return to the first page of the Modify PlayBack function menu press the key D for Back 113 9 LightOn Series User Manual WORK The diagram of Modify PlayBack fucntion menu is the following LightOn console allows the operator to lock the memory of it allowing you to save different configurations and thus prevent unauthorized modification The steps are 1 Activate LED mode via the corresponding buttons 2 Activate the devices you want to change through their respective selection buttons 1 12 3 Press Menu button 4 Press the key D corresponding to Next as shown in the image below 114 5 Then press the key D corresponding to Next LightOn Series User Manual CLEAR BUFFER DMX BASE x lt RH CLEAR BUFFER DMX BASE x lt Pia Fix Patch Channel Setup Edit Group Fader 01 000 Next Led Menu Mode Delete List Fix Auto DMX Fader 01 000 Next 6 Press the key B for Memory Lock 7 By accessing the console will request a password to perform the block Introduce the password 168168 via buttons FX1 FX2 CLEAR BUFFER DMX BASE BID Led Menu Mode Modify PlayBack Memory Lock Master 255 Back FX8 Then press the key D corresponding to Enter to confirmed CLEAR BUFFER DMX BASE FX RACH M
74. remove only one chase Press the key AA corresponding to Delete One menu Delete Menu Delete a One BUFFER e DMX Fader 01 000 Exit In 7 Press the select button 1 12 of chase we want to eliminate mew Delete Menu Ves a Push a Preset lt BUMP gt to DMX Delete Fader 01 000 No In 8 After selecting the device press the key A for Yes to confirm the deleted of the chase 85 LightOn Series User Manual WORK had List Fix Fix List function helps the operator to see easily neatly and clearly the aqssigned devices and their corresponding DMX address The steps for using the Fix List are 1 Active ML mode via the corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup DMX Record BASE Group 4 Then press the key B corresponding to List Fix BUFFER Fix DMX Auto BASE DMX C 5 The display shows the patched devices and their address We will use the key D corresponding to More for move between them Patch by handle CLEAR Num Device DMX BUFFER 01 WK_S72 C2 154 02 WK_S72C2 166 DMX 03 WK_S72C2 178 BASE 04 WK_S72 C2 190 eeek FX Fader 01 000 More eres 86 LightOn Series User Manual WORK 9 Auto DMX LightOn console allows the user to auto addres
75. s FX1 FX2 FX8 and will press the key D for Enter CLEAR Password DMX Ze Cl nase ro o Ce 41 LightOn Series User Manual WORK had 9 After entering the new password the console will introduce requests that again to confirm that they match We again introduce the buttons FX1 FX2 FX8 and press the key D for Enter Change Pswrd Exit CLEAR 7 BUFFER Pls input new password again DMX BASE Cor ee ee er Enter gt x lt gt N a a 4 RH MH 10 After confirming the new password press the key D coresponding to Enter to confirm and exit the Menu Change Pswrd Exit CLEAR Success BUFFER Please remember DMX BASE new Password Enter x lt gt N ON a RH HH NOTE The password is composed of 6 digits After changing the password please write it down and store it in a safe place 42 LightOn Series User Manual WORK 9 MEMORY LOCK LightOn console allows the operator to lock the memory allowing to save the different configurations and thus prevent unauthorized modification The steps are 1 Activate the Single or Scene Two Scene mode by their corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Set Up BUFFER Patch DMX C
76. s that it has both stage A and stage B So we can prepare a scene while there is another in progress The menu entries are explained above in Setup section as in the Single Scene mode The only thing to keep in mind unlike the Single Scene mode is Faders 1 24 control the value of the scene A Faders 25 48 control the value of scene B Example 1 Making CrossFade between scenes 1 Press Scene Two being the key in green colour 2 Raise the Grand Master to 100 3 Press the key 1 24 on the left of the faders 1 12 to adjust the channel level of the scene A 4 Adjust the channel levels 5 Press the key 25 48 located to the left of the faders 13 24 to adjust the channel level of the scene B 6 Adjust the channel levels 7 Raise the preset A and B faders Thus when both sliders are in the upper position is executed scene A 8 Down preset faders A and B Thus when both sliders are in the lower position is executed scene B Shortcuts functions and use of CrossFade for changing modes is equal to the Single Mode Scene Las funciones de Atajos y uso de CrossFade para cambio de modos es igual a la del mod amp ingle Scene 56 LightOn Series User Manual WORK 9 SUBMASTER MODE In submaster mode LightOn console provides the operator the ability to record a different scene on each fader storing up to 576 scenes in 12 pages of 48 scenes each mew Submaster Mode Assign a Fa
77. s the assigned devices automatically The steps to use the Auto DMX are 1 Active ML mode via the corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup BASE Group Fader 01 000 Next In 4 Then press the key C corresponding to Auto DMX BUFFER Fix DMX Auto BASE DMX Cc 5 The display shows the patched devices and their address We will use the key D corresponding to More for move between them lt mew Auto Patch DMX gg a BUFFER No Fader 01 000 In 6 Then press the key A for Yes to auto patch them sequentially 87 LightOn Series User Manual WORK had Modify PlayBack LightOn console allows the operator to edit the stored playbacks Thus the operator can move a show to another place and simply correct positions and focus or make any necessary corrections The steps for using the Modify PlayBack are 1 Active ML mode via the corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup DMX Record BASE Group c Fader 01 000 Next In 4 Then press the key D corresponding to Next BUFFER Fix DMX Auto BASE DMX Cc Fader 01 000 Next In 5 Then press the key A corresponding
78. tively 5 Press the key D corresponding to RUN to implement the Shape 6 Press the key D corresponding to Stop to stop the Shape The LightOn console has a shape generator that gives the operator the ability to create complex effects all quickly and easily 120 LightOn Series User Manual WORK 9 MEMORY PLAYBACK MODE Playback mode is the combination of submaster ML and LED modes From this mode you can run all programming carried out in the console in either mode To do this we must take into account 1 The key 1 24 on the left of the console mode controls the submaster Total 24 pages 2 The 25 44 key located to the left of the console control playbacks recorded in ML and LED modes The steps for PlayBack Mem mode are 1 From any use mode press the button Mem PlayBack 2 The display will display a confirmation message Confirm PlayBack BUFFER Mode DMX No 3 Press the key A for Yes to enter the Mem PlayBack mode 4 Once inside Mem PlayBack mode the display shows Assign BUFFER Up 01 DMX Page c BASE Down 121 LightOn Series User Manual 5 Press the key A for Fade Assign To set the Submaster fade time 6 Press theSubmaster selection button 1 12 that you want to modify y hold down 7 Adjust the Fade value through the STEP RATE fader and release the select button 8 Press the key A again to unch
79. to copy the libraries of the devices on a USB stick 3 Press the key C corresponding to SubMst Upload to copy the information stored in a Submaster to a USB memory 4 Press the key D for Next to access the following options page function Upload BUFFER Upload BASE Upload Master 255 Next HH 7 When you select the option Next proceed to the next page of options which can select among 4 other options 1 Press the key A for Upload ML to copy all the stored information and settings existingin ML mode for movng heads on a USB stick 2 Press the key B corresponding to Led Upload to copy all the stored information and settings existing in the mode LED ona USB stick 3 Press the key C corresponding to Upload Patch to copy information from the console patching in a USB stick 4 Press the key D for Back to return to the first page of feature options Upload BUFFER Upload BASE Upload x Master 255 Next 35 elele LightOn Series User Manual WORK had SYSTEM FILES COPY LightOn console allows the operator the ability to copy and load he libraries information from the submaster mode ML mode moving heads the LED mode and Patch information from a USB stick to the console Being very useful for copying from another console To access this feature perform the following steps 1 Activate the Single or Scene Two Scene modes by t
80. to follow 1 Connect the USB to the console Lighton 2 Power on the console 3 Activate the Single Mode or Scene Two Scene by their corresponding buttons 4 Press Menu 5 Press the key D for the entry Next as shown in the image below Set Up BUFFER Patch DMX Cm vm 2 we Ce 6 Then press the key A for SW Update as shown in the image below SW BUFFER VGA DMX Update BASE Dmx Bs c C sr vn 22 LightOn Series User Manual WORK 9 7 Once inside enter the password 168168 through the buttons FX1 FX2 FX8 CLEAR I Insert USB Password DMX Se A 255 T Enter In 8 After entering the password press D corresponding to Enter to confirm The update is done on a automatically Once finished the update the cfonsole will restart 23 LightOn Series User Manual WORKI I VGA CARD SOFTWARE UPDATE Through this menu you can upgrade the VGA card softwareto the latest version and thus get new images and appearances For more information please go to the official Equipson web www equipson es Once downloaded the file store it in the USB stick under the path L M VGA MAIN The path and file name should not be changed under any circumstances otherwise the console will not find the necessary file Steps to follow 1 Connect the USB to the Lighton console 2 Power on the console 3 Activ
81. xit In 2 Press key A corresponding to Fix Patch Read 00 Fixture CLEAR BUFFER DMX BASE Fader 01 000 BID HH The console will start scanning the libraries available from the USB memory once it indexed them Total 59 CLEAR GEJ mmm w CS BUFFER 02 BBBBB BASE 04 DDDDD More Fader 01 000 Enter In 3 The units are indexed by manufacturer Through the A B and key Cs for Back Next and More you can go moving us Once you locate the manufacturer select it through the key D for Enter 78 LightOn Series User Manual WORK 9 Total 23 CLEAR 01 WKB572C1 Next 02 WKB572C2 DMX 03 WKB57251 04 WKB57252 More Fader 01 000 Enter In IN BUFFER To DMX 001 DMX Press Bump Button to Patch e Fader 01 000 Exit In 5 The selection buttons 1 12 start flashing in red colour and the LCD will display two options you can choose another device through the key A or out via the button B If you patch the selected device will press one of the select buttons 1 to 12 The unit will be patched in the selected fader preset Example 1 patching 8 consecutive devices 1 Select ML mode 2 Press the Menu button 3 Press the key A for FixPatch 4 Press the key C for More 5 Continue pressing thekey C for More to see Work in the display 6 Press the key B
82. y HH Heee mew Auto Patch DMX ga BUFFER DMX BASE No Io Fader 01 000 110 LightOn Series User Manual WORK had Modify PlayBack LightOn console allows the operator to edit the stored playbacks As in ML mode the operator can move a show from a place to another and simply correct positions and focus or make any necessary corrections The steps for using the Modify PlayBack are 1 Activate LED mode via the corresponding button 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Patch BUFFER Setup BASE Group Fader 01 000 Next In 4 Then press the key D corresponding to Next mew Led Menu Mode Delete A BUFFER Fix DMX Auto BASE DMX C x Fader 01 000 Next In 5 Then press the key A corresponding to Modify PlayBK PlayBack BUFFER Lock DMX Fader 01 000 Back In 111 LightOn Series User Manual WORK 9 6 The display will be asked to select the playback you want to modify Hit a Playback CLEAR BUFFER DMX BASE Fader 01 000 Exit JEEN 7 Press the selection button 13 20 who want to modify PlayBack Hu Heek mew Modify Playback p CLEAR 02 XBanDa BUFFER 1 Red 127 own 2 Green 064 DMX 3 Blue 012 Get e PL 01 S001 T005 Next As
83. y Conversely if the console has the configuration of a USB memory preset but has no data on the same subject the console will maintain the preset information 39 LightOn Series User Manual PASSWORD CHANGE This feature allows the operator to change the administrator password of the console Steps to follow 1 Activate the Single Scene Two Scene mode by their corresponding buttons 2 Press Menu button 3 Press the key D corresponding to Next as shown in the image below Set Up BUFFER Patch DMX A 000 Tua Next 4 Then press the key D again for Next as shown in the image below SW BUFFER VGA BASE Dmx_Bs CSC nase Ne 5 Then press the key D again for Next as shown in the image below Set BUFFER Set DMX Upload BASE Lib x Master 255 Next 40 WORK HH HH HH 9 LightOn Series User Manual WORK 9 6 Then press the key B corresponding to Change Paswrd as shown in the image below Files BUFFER Passwrd BASE Memory Master 255 Next In 7 By accessing the console will request a password to perform the password change Entering the password 168168 through the buttons FX1 FX2 FX8 CLEAR Password DMX Ze Cl wn o Ce 9 After entering the old password asks us to introduce the new password Be re introduced through the button
84. y as fade time we have assigned Just as we have assigned a Fade time to channel 3 we can do with the other channels Even with those they have already assigned a Fade time above example 2 By default when you record a submaster this is stored in the page 1 May store any scene in any of the 12 pages this requires holding down the submaster button and press any of the 12 selection buttons to indicate which page we want to record 59 LightOn Series User Manual WORK 9 Example 4 Recording a submaster in any page 1 Select TwoScene or SingleScene mode 2 Adjuste the level of the desired channels eg this time we raise the faders 10 11 and 12 3 Press Record the selection buttons for each channel will flash in red colour 4 Press the Submaster button and hold it 5 Press any of the 12 buttons to select which page we want to record eg press the selection button 2 6 Press the selection channel button where you want to save the scene eg 8 7 Look at the screen to check the recording process once finished this process the red colour buttons will turned off again leaving in green colour the channels that we have adjusted the levels 8 Set all channels to 0 9 Click on Submaster button to access this mode 10 th We press the button again submaster but this time keep it pressed and press a selection button to change the page in that case number2 11 Raise the fader 8 where we recorded a

Lighton Series (Lighton 3 / Lighton 5) User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents