- Polypipe
Contents
1. Index of protection IP20 Displayed temperature update 10s Reading accuracy 1 C at 20 C Reading resolution 0 1 C Swing 0 2 C Comply with EMC and LV directives LVD EN60730 1 EN60730 2 7 EN 60730 2 9 EMC EN 55014 1 EN 55014 2 EN 61000 3 2 EN61000 3 3 Subiect to technical modifications Touch Screen Programmable Room Thermostat Polypipe Building Products Broomhouse Lane Edlington Doncaster DN12 1ES Tel 01709 770 000 Fax 01709 770 001 www ufch com 2410 London Road Mount Vernon Glasgow G32 8 7 Tel 0141 778 8822 Fax 0141 778 2703 Dromore Road Lurgan Craigavon Co Armagh BT66 7HL Tel 028 38 881270 Fax 028 38 882344 www polypipe com Polypipe2. Touch Screen Programmable Room Thermostat Installation and User Manual Polypipe Safety Instruction Step 4 Cover the relay case and screw it properly with screwdriver Installation and mounting of electrical appliances must be carried out only by skilled electricians It is imperative to observe the generally applicable safety measures such as Before starting work on the appliance switch off power supply and secure against switching on Positioning The room thermostat should be positioned away from direct sunlight or heat producing appliances It is recommended that the thermostat is installed 1 2 metres above floor level Installation Step 1 Step 5 Mount and fix rear case with screws in wall Open front and rear case with screwdriver then take off the front case oo Step 6 Put 2 x 1 5v AA batteries into battery box observing polarity Step 2 Open relay case with screwdriver and take off the relay case Step 7 Cover front and rear case correctly Step 3 Day of week 1 Monday 2 Tuesday etc Programmed temp setting Connect all wires properly See page 2 Mode uu 32 1234561 or Increase key Alternating 2 15 current time Kd temp display O Night mod ai o JN A Y Temperature 9 key D 4 nad y 0 setting key ils y La ee Confirmation la al Time
3. key Programme Key OK VE HO EZ Z nu 06 12 18 24 Programmed setting indicator Status indicator showing programmed setting for the day or narmanant cattine Wiring details for single zone master unit PB1ZM PBTSP Wiring details for 4 zone and 6 zone slave PB4ZS and PB6ZS PBTSP JoyedIpu 4 N Nin Aa WIL 11 5 Aa gt aanpey ax SPAD UI dwar Buljas 1 SIET 2 Dum s 2 190 5 ati 1 61 seq ON zu uew d 40 Aep ay 104 Buas pauuweibord Buimoys 21 Sn 652 Q TAT D se TE Ca 2 o du o T vis KK eps n z Kepuon M M JO Aeq Ka gt uonpulluuo Kar BPOW JUBIN ejdsip dwar WI JUAN DunPpul lv Kar Dum s Time Setting LY a Press the key to flash the following in order Year Month Day Hour Minute Use the or key to adjust each b Press OK when complete to confirm exit Note The internal calendar will calculate the correct day of the week 1 Monday etc Note The time with change automatically to adjust BST and GMT on the correct date Temperature Setting 0 There are 3 temperature settings availabl
4. d Press OK key to confirm and exit or exit automatically in 1 minute after 15 seconds the display will switch off The number of hours and the override temperature are flashing alternately on the top right side of the display Press OK to exit from the override function Hold Days Holiday a Press or key to adjust override temperature the symbol EN indicator will appear on the display b Press key twice to display 1d and aif indicator c Press OK key to confirm and exit or exit automatically in 1 minute after 15 seconds the display will switch off The number of hours and the override temperature are flashing alternatively on the top right side of the display Press OK for exit from the override function Hold Long Period Running a Press or key to adjust override temperature the symbol a indicator will appear on the display b Press key three times and will display c Press OK key to confirm and exit or exit automatically in 1 minute after 15 seconds the display will switch off The temperature will be kept until manually pressing OK key Alarm Setting a Press and hold key for 3 seconds to display AL b Then press key once to display Jon the top left Press or key to select the days 1 5 6 7 1 7 c Press key once to flash hour Press or key to set hours of alarm clock d Press key once again to flash minute Press or key to set minutes of alarm cl
5. e Comfort 6 used when room is permanently occupied e g 21 C Economy used when room is temporarily occupied e g 18 C Night J used when the room is unoccupied e g 15 C a Press the key to flash the following in order Comfort Economy Night Use the or key to adjust each b Press OK when complete to confirm exit Mode Setting a Press the key to select the following Automatic programme mode The display vvill also shovv the current temperature at that time e g or Continuous operating at comfort temperature Continuous operating at economy temperature Continuous operating at night temperature Continuous operating at frost protection setting 7 C Quick Set Up To enable quick set up of the Thermostat there is a pre installed programme Simply enter the year date and time Then switch to Auto The programme for each day will be as follows 6 00 a m 8 00 a m Comfort setting Set at 21 C 8 00 a m 6 00 p m Economy setting Set at 18 C 6 00 p m 11 00 a m Comfort setting Set at 21 C 11 00 a m 8 00 a m Night setting Set at 15 C To change any of the temperatures for these times see Temperature Setting Instructions To enter different heating times for each day proceed to Programme Setting Instructions Programme Setting There are three different kinds of programme during the automatic mode That is Daily programme different programme for each day of a week 5 2
6. ock e Press OK to confirm After finishing the setting time buzzer ring BI BI for 30 seconds to the programmed time Press OK key to turn off the alarm clock in the midway To Cancel Alarm a Press and hold key for 3 seconds to display vi Then press and will disappear press OK key to confirm and cancel alarm or exit automatically after 15 seconds the display will switch off Low Battery Indicator When low battery occurs the symbol will appear on the display Change the batteries in a few minutes and the programme temperatures and date setting will remain in memory you only need to reset the time clock hours and minutes Key Lockout Function Hold OK key for 3 seconds to display OK only all keys will be locked out To unlock the keys hold the OK key for 3 seconds to restore the display of the keys Use this function vvhen for example you need to clean the display Technical Data Dimension H x L x W mm 87 x 135 x 32 Operating voltage 2 batteries 1 5v LR6 AA Temperature control range 5 C 435 C Temperature display range 5 C 437 C Switching capacity changeover contact at ohmic loads at inductive loads cos w 0 6 max 6a 240v 50hz max 2a 240v 50hz Switching output Floating Function modes Heat Cool Anti frost 7 C Ambient temperature 5 C 45 C Programming Daily Weekly and 5 2 Class of protection
7. programme the same programme for Monday 1 Friday 2 and the same programme for Saturday 6 Sunday 7 Weekly programme the same programme for each day of a week Daily Programme a Press and hold 3 key for 3 seconds to flash the day 1 7 b Press or key to set the day which you want to programme c After setting the day days press key to flash time 0 00 and the corresponding bar dot for programme is flashing d Press key to enter into energy saving mode press key to enter into comfort sun mode press 3 key to enter into night moon mode e Press or key to adjust time Repeat step d and e if you want to change the programmed level temperature f When you finish setting one day programme press Oto flash day g Set the rest days programme of a week as above operation from step b to step f after finishing all settings press OK to confirm and exit or exit automatically in 1 minute after 15 seconds the display will switch off 5 2 Programme a Press and hold key for 3 seconds to flash date b Press or key to select days from 1 to 5 these days are flashing c Set the programme for Monday Friday and Saturday Sunday by using the same way as Daily Programme A operation Weekly Programme a Press and hold 3 key for 3 seconds to flash date b Press the or key to select days from 1 to 5 these days are flashing c Set the programme by using the same method a
8. s Daily Programme operation Copy Function a Press and hold J key for 3 seconds to flash day and enter into COPY mode when you are in automatic mode The day and COPY are flashing b Press the or key to choose the programme of target day which you want to copy from c Press the key again to stop flashing COPY the programme is memorised d Press or key to choose the day which you want to copy the programme to e Press the key again the programme has been downloaded f In the same way to copy and download programme to the rest days after finishing all programmes press OK to confirm and exit or exit automatically in 1 minute after 15 seconds the display will switch off Manual Override Function During the automatic mode you can have the override function Temporary override Party a Press or key to adjust override temperature the symbol ST indicator will appear on the display b After setting the temperature press OK key to confirm and exit or exit automatically in 1 minute after 15 seconds the display will switch off The manual setting temperature and S will be kept until entering next setting programme or when pressing OK key Hold hours a Press or key to adjust override temperature the symbol ST indicator will appear on the display b Press key once to display 1H and afi indicator c Press or key to set holding time from 1 hour to 24 hours
Download Pdf Manuals
Related Search