AG-168V FXS gateway User Manual
Contents
1. 7 use dda service 8 use vida service 9 use Smartcon s service 10 use avtech s system 11 use Ringtec s system 12 use citron s system 13 use asiasoft s system 14 use txtc s system 15 use i fon s system 16 use suntek s system 17 use asiainfo s system 18 use Lucent s system 19 use IPN s service 20 use yayuang s system 21 use thinker s system 22 use vfon s system set serviceaddr XXXX Set IP address or domain name of gatekeeper set nattraversal X Set NAT traversal or not X ranged from 0 through 6 0 do not use When the log in server and IP phone in the same LAN or the log in system supports the IP phone working behind the LAN 1 Use 46 AG 168V H323 Gateway User Manual V1 43 NAT traversal When the login system does not support IP phone working behind the LAN please use this value to search public IP address of the NAT device With this item selected please make port mapping on NAT device 2 With Citron private protocol used use this value to fit into the GnuGK system transferring the voice and signal by router 3 use this value with Innopath private system used 4 use this value with vida private system used 5 aivgr use this value with aivgr private system used 6 use this value with Eproxy private system used set nataddr XXXXX Set IP address of NAT device wan port or URI of free assistant service Such as www showmyIP com etc in Interne2. ccsecseseesseeeeesteeseeeeeeeeeeeeees 60 Q7 Why is the local IP K KEE 61 Q8 Why is the local IP 255 255 255 255 ssccssecssseeseeeenseeeeseeeeseeeenseeeeeseeeeseeeenseeeeeees 61 Q9 How to reset the AG 168V to the factory default sssnsseee rer 61 Q10 How to use the fast dial up function cceeecestteeeeeeeeeeeeeseeeseseeeeneeeeeenesesneneneeees 62 Q11 Why does the other side feel my voice is very Weak cs cccesssecenseseeeeenees 62 Q12 Why do AT320 AT323 and AG 168V gateway disconnect while calling each other BUEN GS ee EE 63 Q13 What is Dial Plan used for How to Configure it ccesccssseeeeseeeeteesneeenseeees 63 G14 Wihatis inner line seers aeneae e aeae aeea aa aaaeeeaa aaaeeeaa aaaeeeaa 64 Q15 How to speed the register time sccsseeeeseeeseeeeeeseeeeeeeeseaeeeseeeenseeesseesesseeneneeees 65 Q16 HOW toset TOS field eseu ENEE deen stoners 66 AG 168V H323 Gateway User Manual V1 43 1 AG 168V gateway Appearance Introduction e AG 168V gateway Front Illustration Refer to Fig 1 1 Fig 1 1 AG 168V gateway Illustration e AG 168V gateway panel illustration Refer to Fig 1 2 AG 168V H323 Gateway User Manual V1 43 Front Side Back Side Tel port Powerport yp R45 port line port Fig 1 2 AG 168V panel illustration AG 168V H323 Gateway User Manual V1 43 1 1 Indicator light and function Power Indicate power on when alight Status blinkin
3. in the blank after 001 input 56489237 in the blank of phone number then Jack s number of 56489237 will be saved in the first position After setting all of the number press save button then return to the handset connected to the gateway press 001 after the dial tone then the gateway will dial 56489237 automatically Q11 Why does the other side feel my voice is very weak A Pls adjust the input volume larger but pls note the maximum is 15 62 AG 168V H323 Gateway User Manual V1 43 Q12 Why do AT320 AT323 and AG 168V gateway disconnect while calling each other but it rings A Pls check if the phone and gateway is using the same CODEC Q13 What is Dial Plan used for How to configure it A Dial plan is used to convert the number dialed to the number actually sent based on dial number ddd prefix idd prefix ddd code idd code these parameters Parameter use dial plan contains 5 options 1 disable Number sent is the same as number dialed 2 enable If the number dialed is prefixed by idd prefix the number sent will be the rest part of the number dialed dropping off the idd prefix Otherwise if the number dialed is prefixed by ddd prefix the number sent will be idd code the rest part of the number dialed dropping off the ddd prefix Otherwise the number sent will be idd code ddd code the number dialed For example set ddd code 10 idd code 86 idd prefix 00 ddd pr
4. with AG 168V gateway 39 AG 168V H323 Gateway User Manual V1 43 set dns XXX XXX XXX XXX With IPtype set as 0 use this command to set IP address of DNS server set dns2 XXX XXX XXX XXX With IPtype set as 0 use this command to set IP of backup DNS server set mac XX XX XX XX XX XXK Set MAC address of the AG 168V gateway Parameter XX XX XX XX XX XX Must be an HEX number set codec X Set the priority 1of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec2 X Set the priority 2 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec3 X Set the priority 3 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec4 X Set the priority 4 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec5 X 40 AG 168V H323 Gateway User Manual V1 43 Set the priority 5 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec6 X Set the priority 6 of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set vad X Enable disable VAD X is ranged from 0 through 1 0 disable VAD 1 enable VAD set agc X Enable disable AGC X is ranged from 0 through 1 0 disable A
5. 48 AG 168V H323 Gateway User Manual V1 43 ID to login the GK 1 use phone number as E 164 and designated H323 ID by set account XXX command 2 use support automated negotiate about MD5 or CAT authentication system 3 use MD5 authentication account and pin 4 use CAT authentication account and pin 5 use SHA1 authentication account and pin set dtmf X Set DTMF relay type X is ranged form 0 through 2 0 Inband audio 1 H245 string 2 Q931 keypad set superpassword XXXX Set super password of the AG 168V gateway XXX must be ASCII characters set debug X Set open debugging message output grade for special tool X is ranged from 0 through 5 0 close debugging output 1 output the operation information to the window 2 output all the bug information and data in test window 3 save the bug information into SDRAM 4 disable checks the mark set password XXXX Set password of the AG 168V gateway XXX must be ASCII characters set upgradetype X Set auto upgrade matching type X is range from 0 through 5 49 AG 168V H323 Gateway User Manual V1 43 0 disable 1 all 2 mac 3 ppp id 4 account 5 phone number set upgradeaddr XXX XXX XXX XXXK Set IP address or domain name of FTP server supplying upgraded program of AG 168V gateway set sntpIP XXX XXX XXX XXXK Set IP address of time server set daylight X Set use daylight or not X ranged from 0 through 1 0 do not use dayl
6. g711a gsm and iLBC AG 168V H323 Gateway User Manual V1 43 e vad Enable disable VAD voice activity detection e agc Enable disable AGC e aec Enable disable AEC e g 723 1 high rate enable disable g 723 1 high rate G 723 1 high rate is 6 3kbps low rate is 5 3kbps e audio frame Set audio frames in RTP package Minimum is 1 and maximum is 8 e jitter size Set buffer size of RTP package The value range is 0 32 e ilbc payload Set the payload type of RTP package when ILBC codec selected to DTMF delay The value range is 96 255 e handset in Drag the slider to adjust the volume of handset input Drag it to the left to reduce the volume while drag it to the right to increase the volume e Dual mode Set this item to enable or disable the PSTN line Disable With this item selected PSTN line is disabled PSTN First This item selected AG168V FXS gateway will choose PSTN calling first AG 168V H323 Gateway User Manual V1 43 P First This item selected AG168V FXS gateway will choose IP calling first e Dual modes prefix When IP first is set in the dual modes setting setting switches to PSTN prefix such as 9 AG 168V H323 Gateway User Manual V1 43 3 2 3 Dial plan Setting Dial Plan Settings use dialplan disable zl dial number ddd code idd code se idd prefix foo ddd prefix inner line disable v inner line prefix o forward mmber 82378801 fed poweroff TT r f
7. set fwdnumber XXXXXXX Set receiving forwarded calls phone number XXXX must be an Arabic numeral and no longer than 16 characters set fwdalways X Enable disable forward all calls X is ranged from 0 through 1 0 do not forward all calls 1 forward all calls set fwdbusy X Enable disable forward calls if busy X is ranged from 0 through 1 0 do not forward calls if busy 1 forward call if busy set fwdnoanswer X Enable disable forward calls without replying X is ranged from 0 through 1 0 do not forward calls without replying 1 forward call without replying 44 AG 168V H323 Gateway User Manual V1 43 set answer X Set the ring seconds before the phone answers the call auto or forward the calls X is ranged from 0 through 60 set digitmap X Set whether to use digitmap X ranged from 0 to 1 0 do not use digitmap 1 use digitmap set service X Set register the gatekeeper or not A ranged from 0 through 1 0 do not register 1 register set registerttl X Set register TTL X is range from 10 through 65535 Sec Default value is 60 Sec set service type X Enable disable the prepaid and service system choose the repaid server provider or system Parameter x ranged from 0 through 22 0 common disable repaid card 1 use huawei s system 2 use ZTE s system 3 use harbour s system 4 use utstarcom s system 5 use soyo s system 6 use etalk s service 45 AG 168V H323 Gateway User Manual V1 43
8. use dial plan 3 omit prefix The only difference between 2 enable is that if the number dialed is prefixed by inner line prefix the number sent is the number dialed dropping off this prefix Q15 How to speed the register time A Before registration Gateway will first visit FTP server and check if the server has got new firmware or settings to upgrade then it will visit the time server on the Internet to get current date and time If the FTP server s address is a domain name program will visit DNS to resolve this domain name into IP address Besides if local IP address is allocated by DHCP we will check if the allocated IP address conflicts with other devices All these work will cost some time to complete which causes the delay of registration To speed it up try the following two methods 1 set upgrade type to disable then gateway will not check new upgrades 65 AG 168V H323 Gateway User Manual V1 43 from the FTP server 2 set sntp IP to 255 255 255 255 then gateway will not visit timer server to get date and time If one must know the current date and time please set sntp IP to the IP address of a local time server which has fast access Q16 Howto set TOS field A The 8 bit TOS field specifies how the datagram should be handled and is broken down into five subfields Let s assume that bit 0 is the most important bit and bit 7 is the least important bit Bit 0 2 Three PRECEDENCE bits specify dat
9. O disable timezone 55 GMT 08 00 Beijing Hong Kong Urumgi Input ordinary password with debug set as O disable following information will be seen PA168X V1 43 settings Password P gt get HEE ERR RR Network Settings IPtype O static IP 192 168 1 100 subnetmask 255 255 255 0 router 192 168 1 254 dns 202 106 46 151 dns2 202 96 128 68 mac 00 0d ea 00 00 03 kerene Adio Settings r rrr codec1 0 g729 codec2 1 g7231 codec3 2 g711u codec4 3 g711a codec5 6 null codec6 6 null vad 1 enable agc O disable aec 1 enable audioframes 2 6 3k 1 enable ilbcpayload 98 37 AG 168V H323 Gateway User Manual V1 43 jittersize 0 handsetin 7 handsetout 20 dualmode 1 pstn first dualmodeprefix 30 seen Dial Plan Settings dialplan 1 enable dddcode 10 iddcode 86 iddprefix 00 dddprefix 0 innerline 1 enable innerlineprefix 0 callwaiting 1 disable fwdnumber 82378009 fwdpoweroff 1 enable fwdalways 1 enable fwdbusy 1 enable fwdnoanswer 1 enable answer 30 digitmap 1 enable neocon Other Settings re password 1234 upgradetype O disable upgradeaddr empty sntpIP 0 0 0 0 daylight O disable timezone 55 GMT 08 00 Beijing Hong Kong Urumagi gt Command set Syntax descrIPtion set keywords value Usage Used to configure password and other running parameters of AG 168V gateway Detailed descrIPtion set IPtype X Set how AG 168V gateway gets relevant network parameters X ranged from 0 through 3 0 authorize use
10. the wrong firmware into the phone 28 AG 168V H323 Gateway User Manual V1 43 3 2 5 Other settings passnord sntp ip tinezone Other Settings 1234 upgrade type disable DI upgrade addr 0 0 0 0 use daylight GN1408 00 Beijing Hong Kong Urungi Save Settings Address Book Upgrade Firmware Fig 3 6 Other Setting Page e password Set the password of the gateway Default password is 1234 e upgradetype Set the auto upgrade type of the gateway disable Disable auto upgrade all AG 168V will find matching firmware binary file and configuration file of the hardware type only at the FTP server specify by upgradeaddr item mac AG 168V gateway will find matching firmware binary file and configuration file of the MAC address only at the FTP server specify by upgradeaddr item ppp id AG 168V gateway will find matching firmware binary file and configuration file of the ppp id only at the FTP server specify by upgradeaddr item account AG 168V gateway will find matching firmware binary file and configuration file of the account only at the FTP server specify by upgradeaddr item phonenumber AG 168V gateway will find matching firmware binary 29 AG 168V H323 Gateway User Manual V1 43 file and configuration file of the phone only at the FTP server specify by upgradeadar item e upgrade addr Put IP address or domain name obtained by ISP of FTP server supplying upgrade program into this fie
11. AG 168V H323 Gateway User Manual V1 43 AG 168V FXS gateway User Manual i AG 168V GATEWAY APPEARANCE INTRODUCTION ccscccsessees 3 1 1 Indicator light and FUNCTION ccecceseeseeeeeseeeeeeeeeseesesaeenseeeeesneeseaeedseaesneeeeeeseenas 5 2 FEATURES EE E A E T E E 6 2 1 FAN LW ANG ssaa ect ccc eege 6 2 2 SORA eege 6 2 3 Standard and Protocol sseccccseeeesseeeseeeeeseeeeeseeesceeseseeeeeeseeeseaesesneeenseeeeseeseseeeeenseees 7 2 4 Operating requirements ccccecceeeesseeeeseeeeneeeeeeeesesneeeeneneeseaesesaesaseeeeneeesseeeeenseaeees 8 2 5 E OC UE 8 2 6 EE 8 2 7 DPS UE TE 8 3 CONFIGURATION sisssissasevesseassassencsinsseasnsuanedetassnevascasiannbasaventssanseunseusiouineesbens 9 3 1 Phone Keypad Pre configuration ssssssnsssnsennenunrnunnnunnnunnnnnnnnnnnnnnnnnnnnnnn annene 9 3 1 2 Keypad setup Step Dy Step ccccccccssccssscsssessscsssesssenscenecenscenscenacenacenacenacenscenesnaconaeenes 11 3 2 Configured by WEB 22 EAD ERE EES 12 3 2 1 Network fters rarte e Ar EES A ENE EA E OAN 14 3 2 2 And OSET pE EE AEE ATEEN 16 3 2 3 Dial plan Seling sis cicccinsiscunsiccie isis deed deed dd dE edd d e dee d e 19 3 2 4 A323 PFOLOCOL SeT aena 22 3 2 5 Other TEE eegen eegen ae iii iain 29 3 3 Configured by Palm TOO ccccccceeeceeseeeeneeeeeeeeeeseeeseseeeeeeeeeanaesaseeeeeeeeessesaseenenseees 33 3 4 Telnet Gong tege 34 3 4 1 AG 168V Telnet Commands Explanation 222sseuuuversenerererensenenensens
12. GC 1 enable AGC set aec X Enable disable AEC X is ranged from 0 through 1 0 disable AEC 1 disable AEC set audioframes X Set audio frames in RTP package X is Arabic numerals between 0 and 7 set 6 3k X With G 7231 set AG 168V gateway to use 6 3K rate or not X is ranged from 0 through 1 0 use 6 3K rate 1 use 5 3K rate set jittersize X Set buffer size of RTP package X is range from 0 32 41 AG 168V H323 Gateway User Manual V1 43 set ilbcpayload X Set the payload type of RTP package whne ILBC codec selected to DTMF delay X is range from 96 255 set handsetin X Set initial volume of handset X is ranged from 0 through 15 set handsetout X Set initial volume of handout X is ranged from 0 through 31 set dualmode X Set to enable or disable the PSTN line X ranges from 0 through 2 0 do not use PSTN line 1 use PSTN line first 1 use IP side call first set dual modes prefix XX When IP first is set in the dual modes setting setting switches to PSTN prefix XX ranges from 0 through 99 set dialplan X Enable disable dial plan and dial number Parameter X ranged from 0 through 4 0 disable dial plan 1 enable dial plan 2 use dial number 3 use 179XX service 4 use hotline function set dialnumber XX When set dialplan value set as 2 please use this command to set dial number For example with eTalk card used please set it as 42 AG 168V H323 Gateway User Manual V1 43 00 When set dialpl
13. When this is selected please select 22 AG 168V H323 Gateway User Manual V1 43 dialnum from the Use dialplan list box and put 00 into dial number dda Use Dda s system vida Use Vida s system smartcon Use Smartcon s service auvtech use Auvtech s system ringtec Use Ringtec s system When this is selected please select dialnum from the Use dialplan list box and put Ringtec account into dial number citron Use Citron s system asiasoft Use Asiasoft s system xtc Use tice system j fone Use i fone s service suntek Use Suntek s system asiainfo Use Asiainfo s system lucent Use Lucent s system 23 AG 168V H323 Gateway User Manual V1 43 IPN Use IPN s service yiyang Use Yiyang s system thinker Use Thinker s system vfone Use vfone s service e service addr Please set the URI domain name IP address service port of the server into service addr When the default service port is used service port can be omitted If use service is checked please set the URI of gatekeeper into service addr The default service port is 1719 If use service is not checked to make calls through gateway please put the URI of the gateway into service addr To make IP to IP call please clear this field In both cases the default service port is 1720 e nat t
14. agram precedence with values ranging from 0 normal precedence through 7 network control allowing senders to indicate the importance of each datagram Bit 3 Also called D bit When set the D bit requests low delay Bit 4 Also called T bit When set the T bit requests high throughput Bit5 Also called R bit When set the R bit requests high reliability Bit 6 7 Unused TOS is just a hint to the routing algorithm that helps it choose among various paths to a destination An internet does not guarantee the type of transport requested 66 AG 168V H323 Gateway User Manual V1 43 Reserves the right to make changes in technical and product specification without prior notice AG 168V FXS gateway User Manual V1 43 All rights reserved 67
15. an value set as 4 please use this command to set hotline number set dddcode XX Set the area code when set dialplan value set as 1 or 2 For example the area code of Beijing is 10 the area code of Shanghai is 21 and the area code of Chengdu is 28 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set iddcode XXX Set the country code when set dialplan value set as 1 or 2 For example the country code of China is 86 the country code of USA is 1 etc Parameter xxxx must be an Arabic numeral and no longer than 4 characters set iddprefix XX Set IDD service prefix number when set dialplan value set as 1 or 2 For example IDD service prefix number of china is 00 IDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set dddprefix XX Set DDD service prefix number when set dialplan value set as 1 or 2 For example DDD service prefix number of china is 0 DDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters 43 AG 168V H323 Gateway User Manual V1 43 set innerline X Set use innerline call or not X ranged from 0 through 1 0 disable 1 enable innerline call set innerlinepreifx X With innerline set as 1 enable please set the prefix to pick up inner line such as 0 set callwait X Set whether to use call wait X ranged from 0 to 1 0 do not use call wait 1 use call wait
16. assigns all the required network parameters to any device connected to it when the device log on AG 168V gateway is shlPped from the factory with DHCP on So if your LAN or router is configured to use DHCP addressing the gateway s LAN parameters will automatically be configured as soon as it is connected to the LAN or router and powered up PPPoE Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them With this system ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on modem If the AG 168V gateway used with modem please select this 14 AG 168V H323 Gateway User Manual V1 43 item to get relevant network parameters auto Then please fill ID and pin into ppp id and ppp pin fields e ppp id With PPPoE or modem selected in IPtype drop down list please enter the user name here e ppp pin With PPPoE or modem selected in IPtype drop down list please enter the password here e local IP With static IP selected in IPtype drop down list please enter IP address of AG 168V gateway here e subnet mask With static IP selected in IPtype drop down list please enter subnet mask of AG 168V gateway here e router IP With static IP selected in IPtype drop down list please enter router IP address of AG 168V gateway here e dns With static IP selected in IPtype drop down list please enter IP a
17. ckup the handset input IP address after dial tone press to send numbers 2 Press speaker input IP address after dial tone press to send numbers Notice Dial with IP address using instead of e Call with GATEWAY If registered in Gatekeeper dial the number 56 AG 168V H323 Gateway User Manual V1 43 Pick up the handset or Press speaker dial the number after the dial tone and then press to send the number 5 2 Call when PSTN first Dual mode enabled Call PSTN number When PSTN first set the way of dial is the same as normal PSTN phone Call VoIP number Press the cradle or the flash key of the normal phone enable AG 168 to be in volP state from pstn first mode Dial after the dial tone Refer to Call when Dual mode disabled chapter 5 3 Call when IP first Dual mode enabled Call VoIP number When IP first was set pick up the phone and dial as Call when Dual mode disabled chapter Call PSTN phone Predial the prefix number in the dual mode prefix AG 168V will change to PSTN line call after the dial tone 5 4 Emergency Call When AG 168V is power off or the network is down the Normal phone would connect with the PSTN LINE work as the LIFELINE and call emergency number 57 AG 168V H323 Gateway User Manual V1 43 6 Reset AG 168V to factory default AG 168V has its default factory setting Changing the firmware version or setting frequent
18. d a keep alive registration message to H323 gatekeeper every register ttl seconds The value range is 10 65535 Default is 60 e local type This parameter refers to how IP phone authenticate itself to the gatekeeper The meaning of each item is as follow phone number Use phone number as E 164 and H323 ID to login the GK account Use phone number as E 164 and designated H323 ID filled in account field as H323 ID to login GK auto use support automated negotiate authentication account and pin about MD5 or CAT md5 use MD5 authentication account and pin Cat use CAT authentication account and pin sha1 use SHA1 authentication account and pin 27 AG 168V H323 Gateway User Manual V1 43 e dtmf Set DTMF signal sending way by selecting inband audio h245 string q931 keypad from list box e super password Set the super password of the phone Default super password is 12345678 e debug Set the debug level of the phone a disable Disable output the debug message by selecting this item a output Output the operation information to the window such as register input by selecting this item output all Output all debug information and data in test window by selecting this item remote debug Save the debug information in SDRAM of IP phone by selecting this item a no check Disable checking firmware tags when upgrading This is not suggested because it will increase the risk of upgrading
19. ddress of DNS server here e dns 2 With static IP selected in IPtype drop down list please enter IP address of backup DNS server here e mac MAC address is the physical address supplied by the Ethernet NIC AG 168V Gateway is shlPped from the factory with a unique AG 168V H323 Gateway User Manual V1 43 algorism MAC address printed on the back of the base 3 2 2 Audio Setting Audio Settings codecl z129 codec Jeitz gt codec3 eTiiu zl codect gsn e codecS mu gt codecd mi sl vad v age E aer Iw audio franes E 723 1 high rete e ilbe payload pB jitter size o handset in i0 15 fis handset out 0 31 jo dual node pstn first m dual mode prefix po Fig 3 3 Audio Setting e codec1 Set the priority 1 of the audio compression algorithm The options are g729 g7231 g711u g711a gsm and iLBC e codec2 Set the priority 2 of the audio compression algorithm The options are g729 g7231 g711u g711a gsm and iLBC e codec3 Set the priority 3 of the audio compression algorithm The options are g729 g7231 g711u g711a gsm and iLBC e codec4 Set the priority 4 of the audio compression algorithm The options are g729 g7231 g711u g711a gsm and iLBC e codec5 Set the priority 5 of the audio compression algorithm The options are g729 g7231 g711u g711a gsm and iLBC e codec5 Set the priority 6 of the audio compression algorithm The options are g729 g7231 g711u
20. down list set long distance call prefix according to E 164 dial rule such as 0 Note With dialnum seletcted in use dialplan drop down list you can also set dddcode iddcode iddprefix and dddprefix according to requirement of system e innerline Enable disable multi settings by selecting corresponding items from dropdown list AG 168V Gateway allows saving 5 settings totally disable Disable multi settings by selecting this item then the Gateway will call out using current setting enable Use designated system to place calls by selecting this item m innerlineprefix With enable selected in innerline dropdown list please fill the prefix number pick up to inner line such as 0 e Use digitmap Enable disable digit map by checking unchecking the box 20 AG 168V H323 Gateway User Manual V1 43 e Call waiting Enable disable call waiting by checking unchecking the box e forward number Enter receiving forwarded calls phone number into this field If the AG 168V gateway used with modem with modem item selected in IPtype list box and then fill ISP number into this field e fwd poweroff Forward calls if power off by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd noanswer Forward calls without replying by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd always Forward all calls by checking this box Pleas
21. dress Book Upgrade Firnvare Fig 3 7 Setting Page using ordinary pin with Debug set as 0 disable e Save Settings Click this button to save the configuration and the gateway will reboot Once the gateway reboots successfully the new configuration is effective Note After entering set page if save settings button is not clicked within 10 minutes then when you click it again the index page asking for pin will pop up again Then please input the password again to enter the set page and then click save settings button to confirm the modification e Address Book Click this button to open the speed dial settings page Please refer to Fig 3 8 In this page you can set and save the speed dial number by typing the name into the Name field and then entering the corresponding number following the name For example input Jack in Name field following 001 and then input 5989426454 into Phone number 31 AG 168V H323 Gateway User Manual V1 43 No 001 003 005 DOT 009 field Then Jack s number 5989426454 is saved in phone book Then please click Save Back button In normal state you can use speed dial to call numbers saved in phone book Phone Book Phone Number No Name 5989426454 me fen t S We 004 i nee CUTTY Ee 008 an Eee 010 Deag Fig 3 8 Phone Book Illustration Phone Namber 192 168 1 56 Upgrade Firmware Click this button to update the program the ring and the digit map of AG 168V
22. e RTP Real time Transport Protocol e RTCP Real time Control Protocol e VAD CNG save bandwidth e DHCP Dynamic Host Configuration Protocol e PPPoE PPP Protocol over Ethernet e DNS Domain Name Server e Telnet Internet s remote login protocol e FTP File Transfer protocol e HTTP Hyper Text Transfer protocol AG 168V H323 Gateway User Manual V1 43 2 4 2 5 2 6 2 7 e Build in H323 proxy Operating requirements e Operation temperature 0 to 40 C 32 to 104 F e Storage temperature 30 to 65 C 22 to 149 F e Humidity 10 to 90 no dew Electric requirements e Voltage 9V 24V e Power adapter output DC 12V 450mA e Network interface 1 X RJ 45 Ethernet Connectors Size 153 X 124 X 27 m LxWxH Installation Connect handset to base insert handset cord into handset cord jack at the left side of the base Connect AG 168V gateway to Internet plug the RJ 45 Ethernet cable into the Ethernet Jack Plug the other end of the cable into HUB Power on AG 168V gateway plug the power cord adapter into the Power Jack Then plug the other end of the power cord adapter into the appropriate wall outlet AG 168V H323 Gateway User Manual V1 43 3 Configuration Four different ways can be used to configure AG 168V Gateway phone keypad pre configuration web browser Telnet commands and PalmTool configuration tool on computer 3 1 Phone Keypad Pre configuration Using
23. e and confirm it 3 End of Upgrading During upgrading the Palmtool shows the information of Updating please 59 AG 168V H323 Gateway User Manual V1 43 wait until the update led stops flashing Then the Server light will keep on blinking The updating will need some time after update successfully AG 168V gateway will reboot automatic Q4 Why the Palmtool shows can t connect to palm1 message box A there are several reasons that palmtool shows can t connect to palm1 when user try to use palmtool to configure the gateway 1 AG 168V was not connected to the computer 2 The IP address you have filled in the Palmtool is not the IP address of your gateway 3 The debug option is set to disable You can change it to output through IE 4 Your computer and your gateway are in the difference subnet Please change the setting of your computer or the gateway to let them in the same network Q5 How to update the protocol for the AG 168V A Please refer to chapter 4 Q6 What should do if can t access my gateway A you can try the following method 60 AG 168V H323 Gateway User Manual V1 43 1 Reset the device to factory default Please ref 2 if this can t help 2 Upgrade AG 168V firmware in safe mode Step 1 Enter safe mode power off gt press and hold the IP button and then power on release the IP after 10 seconds gt Power and Server light are lit Then the AG 168V is
24. e enter receiving forwarded calls phone number into fwd number field e fwd busy Forward calls if busy by checking this box Please enter receiving forwarded calls phone number into fwd number field e answer Enter a number from 0 through 60 to set the entries of the seconds before the phone answer the call auto or forward the calls Note please refer to FAQ for more information of dial plan 21 AG 168V H323 Gateway User Manual V1 43 3 2 4 H323 Protocol Settings H323 Protocol Settings use service Iv service type common service addr 203 93 9 57 nat traversal aisahle zl nat addr lt lt 5 22 nat ttl bn phone number 2378808 account hae pin eegen ras port i720 9931 port fi720 h245 port 1722 rtp port i722 tos p register ttl jo local type phonenumber zl DOT h245 string gt super password 12345678 debug output zl Fig 3 5 H323 Protocol Settings e use service Enable disable service by checking clearing this box To make calls through gatekeeper please check this box otherwise phone can only make IP to IP calls or calls through gateway e service type This option is used to accommodate the miscellaneous requirements of the system providers Common no special requirements Huawei Use Huawei s system ZTE Use ZTE s system harbour Use Harbour s system utstarcom Use UTstarcom s system soyo Use Soyo s service etalk use etalk prepaid card
25. efix 0 If the number dialed is 00 1 4089821818 the number sent will be 1 4089821818 63 AG 168V H323 Gateway User Manual V1 43 If the number dialed is 021 82378008 the number sent will be 8621 82378008 If the number dialed is 82378008 the number sent will be 861082378008 3 dial number Convert the number dialed to a new number according to enable dial plan then prefix dial number to this new number This new number is the number sent 4 prefix Effective only when dial number is not empty This serves for those calling cards The number sent is just dial number During the call connection program will automatically send out a number made up with account pin number converted by enable dial plan 5 hotline The number sent is dial number Whenever the handset is lifted up this number will be automatically dialed out Q14 What is inner line A Parameters inner line and inner line prefix help to distinguish whether the number dialed is an inner line number inner line contains 3 options 1 disable No distinction among numbers The number sent is the number converted 64 AG 168V H323 Gateway User Manual V1 43 according to parameter use dial plan 2 enable If the number dialed is prefixed by inner line prefix the number sent is just the number dialed because this number is an inner line number Otherwise the number sent is the number converted according to parameter
26. ensene 35 4 UPGRADE 3 AG 168V GATEWAY cccccccccrscccrssccssscccssecsensccccssccssenecoes 54 4 1 Use IE browse to upgrade the AG 168V gateway scccssccssseeeeeteesesesseeeeeeees 54 4 2 Use the PalmTool to upgrade the AG 168V gateway cssccesssseeesseeenseeees 54 5 USAGE OF THE GATEWAY scssvcissseinssvessssvn cess snasocessvedecieinnarisenssiseesieasseesions 56 5 1 Receiving Call Se aerer gesteet 56 5 2 Call when Dual mode disabled c s ccceceeseeesseeeeeneeeeeeeeseeeseseeeenseeeesseesesnenenseees 56 5 2 Call when PSTN first Dual mode enabled cssecceeeeeesseeeeseeeeeeeeeeeeesesseeenseeees 57 5 3 Call when IP first Dual mode ernabled sccccssccseeeeeeeeeeseeeeeseeeenseeeseeesesneeeneneees 57 5 4 Emergency talk eseou ege Eege 57 6 RESET AG 168V TO FACTORY DEFAULT cccscssssssssssscsssssssseeees 58 AG 168V H323 Gateway User Manual V1 43 T PAC P E E E E A A E E E EE 59 Q1 How can I obtain the AG 168V s IP assnssunnuunnuunnuunnunnnnunnnunnnunnnunnnnunnnnnnnnnnnnnnnnnnnn 59 Q2 Why I can t see the complete setting page when access the AG 168V by IE 59 Q3 How to use the PalmTool to upgrade the AG 168V gateway ssseeese 59 Q4 Why the Palmtool shows can t connect to palm1 message box 0 0 60 Q5 How to update the protocol for the AG 168V asssaannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn 60 Q6 What should I do if I can t access my gateway
27. er auto to get the corresponding file and deal with it Relevant usage ftp X X ranged from 0 through 2 X 0 Connect to FTP Server to get the file of updating program and save it to the SDRAM of the phone Then the file can be read by PalmTool This operation aims at testing X 1 Connect to FTP Server to get the file of updating program and update program Flash This operation aims at updating program X 2 Connect to FTP Server to get the file of updating dial rules and update program Flash This operation aims at updating dial rule Note When you use ftp 0 and ftp 1 commands if the file get from FTP server is too large or the net speed is too slow then the process will not be seen in telnet window Please be patient Using ftp command in telnet to get file soends almost same minutes as getting file using phone So if nothing is displayed after too long time it means that ftp is fail Note All the Telnet commands of AG 168V gateway should be written in low case and the password is case sensitive 52 AG 168V H323 Gateway User Manual V1 43 53 AG 168V H323 Gateway User Manual V1 43 4 Upgrade AG 168V gateway 4 1 4 2 Use IE browse to upgrade the AG 168V gateway Step 1 Fill the AG 168V gateway in the IE browse press the IP button and pick up the handset to obtain the gateway s IP Step 2 Use super password to access the AG 168V setting page and choose the debug caption to the item except no output Ste
28. etting mode and then you can set the AG 168V gateway by using the telnet commands 34 AG 168V H323 Gateway User Manual V1 43 3 4 1 AG 168V Telnet Commands Explanation AG 168V Telnet Commands Command Function Supply command name and parameters get Display basic parameters of AG 168V gateway set Set parameters of AG 168V gateway store Save current settings to designated position load Load designated settings to current position exit Exit from the setting mode without saving the configuration write Exit with saving all configurations and restart AG 168V ping Ping other net parameter ftp The gateway connects to FTP server and then get the files Detail descrIPtion of AG 168V Telnet commands gt Command Syntax descrlPtion No optional parameter Usage Type command name and parameters following P gt Be used as the keyword to supply keyword and parameters of the relevant commands Relevant usage None ER AG 168V H323 Gateway User Manual V1 43 Detailed descrIPtion List help of all commands For example P gt set get list settings store x store current to xth settings load x load xth settings to current exit write save settings gt Command get Syntax descrIPtion No optional parameter of keywords Usage Display basic parameters of AG 168V gateway Relevant usage None Detailed descrIPtion get Display basic running parameters of the AG 168V gateway Input ordinary password without debug bei
29. g when making a call Server blinking when registering go out when registered Line port connect to PSTN line Tel port connected with handset LAN port connect to network IP button enter setting mode please refer to chapter 3 1 AG 168V H323 Gateway User Manual V1 43 2 2 1 2 2 Features Hardware Main chIP PA1688LQ 50MHz Data Memory 16MB SDRAM Program Memory 16 MB Flash memory FXS Port 1 FXS Port for Tel Line Port 1 Line port for PSTN Ethernet Jack 1 X10 jack AC DC adapter Output 12V DC 450mA Software DHCP support for LAN or Cable modem PPPoE support for ADSL or Cable modem Set Gateway by HTTP web browser IE6 0 or Telnet Upgrade by FTP Support major G 7XX GSM 610 iLBC audio Codec VAD Voice Active Detect CNG Comfort noise generation Dynamic voice jitter buffer G 168 165 compliant 16ms echo cancellation Tone generation and Local DTMF re generation according with ITU T AG 168V H323 Gateway User Manual V1 43 2 3 e E 164 dial plan and customized dial rules e 100 entries for quick dial e 80 entries each for missed calls answered calls and dialed calls e Voice prompt e Hotline e Support adjustable user password and super password Standard and Protocol AG 168V gateway supports following standard and protocol e EEE 802 3 802 3 u 10 Base T 100Base TX e Major G 7XX GSM610 iLBC audio Codec H323 V4 e TCP IP Internet transfer and control protocol
30. gateway Firmware File Name GEZ Update Firmware Digitmap File Name RIG Update Digitmap Fig 3 9 Upgrade firmware Illustration Ring File Name RU Update Ring 32 AG 168V H323 Gateway User Manual V1 43 3 3 Configured by PalmTool PalmTool is a tool designed especially to configure and upgrade the AG 168V gateway On a PC double click icon to open the PalmTool The index page of PalmTool will popup Input the IP address of the phone into Local IP field such as 192 168 1 100 and then click Phone Settings button Use PalmTool to set the AG 168V gateway please set debug as output or output all firstly otherwise PalmTool cannot connect AG 168V gateway The parameters of PalmTool is same as the parameters in HTTP so please refer to HTTP set chapter to learn how to set AG 168V gateway 33 AG 168V H323 Gateway User Manual V1 43 3 4 Telnet Configuration e On the PC choose Start gt Run and then type telnet 192 168 1 100 into Run field in popuping Run dialog Or input telnet 192 168 1 100 in the DOS window Then the following information will be displayed PA168X V1 43 settings Password Then please type password With debug is set as O disable if type ordinary password default one is 1234 after Retun you will see Password P gt If you type super password then you will see Password a kkkkkkkk P gt Above information indicates that AG 168V gateway is under s
31. ight 1 use daylight set timezone XX Set time zone gt Command store Syntax descrIPtion no keyword Parameter ranged from 0 through 4 Usage Save the current settings to the designated position Relevant Usage store 1 gt Command load Syntax descrIPtion no keyword Parameter ranged from 0 through 4 Usage Load the designated settings to the current position Relevant Usage load 1 50 AG 168V H323 Gateway User Manual V1 43 gt Command exit Syntax descrIPtion no keyword and parameter Usage Exit from Telnet command window without saving the configuration Relevant usage None gt Command write Syntax descrIPtion No keyword and parameter Usage Save the configuration and restart the AG 168V gateway gt Command ping Syntax descrIPtion ping IP address Usage ping IP address of other NAT device Relevant usage In telnet window input ping xx xxx xx xx an IP address and return then the result will be displayed If the address is effective ping OK will be seen if the address is ineffective nothing will be seen Fox example P gt ping 203 93 9 57 P gt ping OK 51 AG 168V H323 Gateway User Manual V1 43 P gt ping 27 56 120 56 P gt Note Usually the echo time of ping command is no more than 1 second So if the result is not displayed in 5 seconds ping command is fail gt Command ftp Syntax descrIPtion ftp value Usage the system connects to the FTP serv
32. in the safe mode and have a static IP 192 168 1 100 now Step2 use palmtool to upgrade the firmware refer to Q3 Notice You can only use PalmTool to upgrade firmware in safe mode status Q7 Why is the local IP 0 0 0 0 Al the AG 168V IPtype is set to DHCP and your network doesn t support DHCP function The AG 168V will shows 0 0 0 0 Pls Check your network in this case Q8 Why is the local IP 255 255 255 255 A Probably AG 168V gateway fails to get IP address if you choose the IPtype to PPPOE you can set your AG 168V s IPtype to static or DHCP through keypad please refer to chapter 3 1 or reset to the factory default Q9 How to reset the AG 168V to the factory default Power up Power light is on 61 AG 168V H323 Gateway User Manual V1 43 Wait until initialization is complete Status light goes out Pick up phone not connected tone is heard Dial 1234 Power and Status light are lit Server light is blinking Push and hold IP button on rear for 10 seconds Power and Server light are lit Push flash key once Dial 5 5 Server light will blink for a while and then the Statue light will lit for a while And then the Gateway will reboot automatically Q10 Howto use the fast dial up function A Use Palmtool or IE to enter into the setting page find the address book fill the name and the full number in the right blank For example fill Jack
33. ld e sntp IP Fill IP address of time server here When network without Internet connect Fill special IP address 255 255 255 255 e use daylight Enable disable daylight e timezone Select correct time zone in list box When debug set as O disable if input ordinary password default one is 1234 then following page will pop up after clicking LC And only those parameters can be modified 30 AG 168V H323 Gateway User Manual V1 43 Network Settings iptype static DI ppp id PEP pin local ip 192 168 1 100 subnet mask 266 2556 266 0 router ip 192 168 1 264 dns 202 106 46 151 dnsz 202 96 128 68 mac D0 09 45 0a745 2e Audio Settings codec1 8729 gt codec2 27112 z codecd feTllu codecd4 esn e codecS mu gt codec null vad ei age O sec audio Frames E z T23 high rate m ilbe payload dual mode posta first D dual mode prefix 30 Dial Plan Settings se jiiter size fo handset 1100 15 fis handset out 0 31 CE Tllu ull e Vv 98 20 NM Vv 30 use dialplan enable x dial mmber jeet ddd code fio idd code 86 idd prefix foo ddd prefix 0 immer line enable z inner line prefix fo call vaiting forward number 95963 Sei power ff P fed noanswer fwd alvays e fwd busy a ancver fo use digi trap T Other Settings pasvord pa oo upgrade type disable upgrade addr a 7 sutp ip 255 255 255 255 use daylight C tinazone CMT 08 00 Boijine Hone Kong Dome d Ad
34. ly may make the AG 168V in a chaos status In this case you can restore the AG 168V to its factory default through the following procedure Power up Power light is on Wait until initialization is complete Status light goes out Pick up phone not connected tone is heard Dial 1234 Power and Status light are lit Server light is blinking Push and hold IP button on rear for 10 seconds Power and Server light are lit Push flash key once Dial 5 5 Server light will blink for a while and then the Statue light will lit for a while And then the Gateway will reboot automatically 58 AG 168V H323 Gateway User Manual V1 43 7 FAQ Q1 How can obtain the AG 168V s IP A press IP and pick up the handset connected to the FXS port of AG 168V then you can hear AG 168V s IP from the handset Q2 Why can t see the complete setting page when access the AG 168V by IE A Pls access the AG 168V through super password You can t see the complete setting page through normal user password when the debug obtion is set to disable Q3 How to use the PalmTool to upgrade the AG 168V gateway 1 Set IP address press the IPs button and pick up the handset to obtain the gateway s IP and fill this IP in the IP address blank of PalmTool 2 Choose the updating file The updating file is bin file press upgrading the program there come out a new window and choose the corresponding updating fil
35. ng set as O disable or input super password with debug set as O disable then following parameters of AG 168V gateway will be displayed PA168X V1 43 settings Password P gt get Henne Network Settings IPtype O static IP 192 168 1 100 subnetmask 255 255 255 0 router 192 168 1 254 dns 202 106 196 152 dns 2202 106 196 115 mac 00 09 45 65 a3 e6 nee A Udi Settings codec1 0 g729 codec2 1 g7231 codec3 2 g711u codec4 3 g711a codec5 6 null codec6 6 null 36 AG 168V H323 Gateway User Manual V1 43 vad 1 enable agc O disable aec 1 enable audioframes 2 6 3k 1 enable ilbcpayload 98 jittersize 0 handsetin 7 handsetout 20 dualmode 1 pstn first dualmodeprefix 30 HERRER Dial Plan Settings tee dialplan 1 enable dddcode 10 iddcode 86 iddprefix 00 dddprefix 0 innerline 1 enable innerlineprefix 0 callwaiting 1 disable fwdnumber 82378009 fwdpoweroff 1 enable fwdalways 1 enable fwdbusy 1 enable fwdnoanswer 1 enable answer 30 digitmap i1 enable HERR Protocol Settings service 1 enable registerttl 60 servicetype 0 common serviceaddr 203 93 9 57 nattraversal 2 citron nataddr empty natttl 30 phonenumber 82378808 account empty pin empty rasport 1720 q931port 1720 h245port 1722 rtpport 1722 tos 0 localtype O phonenumber dtmf 1 h245 string stereo Other Settings ee superpassword 12345678 debug 1 output password 1234 upgradetype O disable upgradeaddr empty sntpIP 0 0 0 0 daylight
36. p 3 Click Upgrade firmware select the correct program on the firmware file blank and click upgrade to perform upgrade Use the PalmTool to upgrade the AG 168V gateway 1 Set IP address press the IPs button and pick up the handset to obtain the gateway s IP and fill this IP in the IP address blank of palmtool 2 Choose the updating file the updating file is bin file press upgrading the program there come out a new window and choose the corresponding updating file and confirm it 3 End of Upgrading During upgrading the Palmtool shows the information of Updating please wait until the update led stops flashing Then the Server light will keep on blinking The updating will need some time after update 54 AG 168V H323 Gateway User Manual V1 43 successfully AG 168V gateway will reboot automatic 55 AG 168V H323 Gateway User Manual V1 43 5 5 1 5 2 Usage of the gateway Receiving calls No matter what calls from IP or PSTN the phone connecting to AG 168V FXS port will ring You can pick up the handset or the speaker of the normal phone to receive the call Call when Dual mode disabled Call with phone number 1 Dial with handset pickup the handset dial after dial tone 2 Dial with speaker press speaker dial after dial tone 3 Redial press redial and call the last number Call with IP address If not registered in gatekeeper and gateway disabled dial with the IP address 1 pi
37. raversal When the IP phone with private IP address need communicate with other IP phones in a different LAN or on Internet please select an item from dropdown list disable Select this item when the login server and IP phone in the same LAN or the login system supports the IP phone working behind the LAN 24 AG 168V H323 Gateway User Manual V1 43 enable When the system does not support IP phone working behind the LAN please select this item to search public IP address of the NAT device With this item selected nat addr field will be activated Besides port mapping port forwarding needs to be properly set up on NAT device citron With Citron private protocol used select this item to fit into theGnuGK system transferring the voice and signal by routed innopath Select this item with Innopath private system used vida Select this item with Vida private system used aivgr Select this item with aivgr private system used eproxy Select this item with eproxy private system used e nat addr When nat traversal is set to enable please put the domain name of the servers These web server helps to find out the Di public IP of the IP phone into nat addr such as www whatismylP com e nat ttl When IP phone sit behind a NAT device it will send packets to server every nat ttl seconds to keep the port mapping on the NAT device alive nat ttl is an integer bet
38. rs set IP address subnet mask and router IP address of AG 168V gateway manually 1 use DHCP mode With this system your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on AG 168V gateway is shlPped from the factory with DHCP on So if your LAN or router is configured to use DHCP addressing the AG 168V gateway s LAN parameters will automatically be configured as soon as it is 38 AG 168V H323 Gateway User Manual V1 43 connected to the LAN or router and powered up 2 use PPPoE mode Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them With this system ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on 3 use modem mode Those who use AG 168V gateway with modem please set the value as 3 set pppid XXX With IPtype set as 2 use this command to set ADSL ID with IPtype set as 3 use this command to set Modem ID set ppppin XXX With IPtype set as 2 use this command to set ADSL pin with IPtype set as 3 use this command to set Modem pin set IP XXX XXX XXX XXX With IPtype set as 0 use this command to set IP address of AG 168V gateway set subnetmask XXX XXX XXX XXX With IPtype set as 0 use this command to set subnet mask of AG 168V gateway set router AAA ANN XXX XXX With IPtype set as 0 use this command to set router IP of network
39. service type common x Ppp pin router ip mac codecd codeck acc ilbe payload handset out 0 31 ddd code ddd prefix call vaiting fwd noanswer ansver service addr sit ron DI nat addy net ttl phone number 272727 account pin 5060 9931 port 5000 5002 tos fo phonenunber x dint Jinband audio super password 12345678 debug output all D passvord sntp ip tinerone Other Settings 1234 upgrade type disable sl 255 255 255 255 use daylight P GMI 08 00 Beijing Hong Kong Urunqz X 1245 pori regisier ttl upgrade addr IER 168 1 254 fo 0 09 d5 Na d5 2e Bie Fx sj ra eja EI of ch Ion 1 a S IK 203 93 9 ST 6002 d Save Settings Address Book Upgrade Firnvare Fig 3 1 Http Setting 13 AG 168V H323 Gateway User Manual V1 43 3 2 1 Network Setting network settings iptype static Ppp id beet Ppp pin beet local ip 192 168 1 100 subnet mask 255 255 255 0 router ip 192 168 1 254 dns 202 106 196 115 dns2 202 96 128 68 mac 00 09 45 63 17 a8 Fig 3 2 Network Setting e Ptype Set how AG 168V gateway gets relevant network parameters by selecting corresponding item from drop down list m static IP Select this item to authorize users set IP address subnet mask and router IP address of AG 168V gateway manually dhcp Select this item to enable DHCP mode With this system your LAN or router automatically
40. t Note The free service list of Internet www IP calculator com www Pchicken com www Pchicken com www showmyIP com www whatismyIP com www mylPaddress com www whatismylPaddress com IP sbbs net www whatismy lPaddress net checkIP dyndns org set natttl XX Set NAT TTL XX is an integer between 10 and 65535 sec Default value is 20 sec set phonenumber XXXXXXXX Set a phone number of AG 168V Gateway Value xxxxx must be an Arabic numeral and no longer than 16 characters 47 AG 168V H323 Gateway User Manual V1 43 set account XXXXXX While calling card is set set account of chosen card while local type is set use authentication type set user ID while set localtype is set as 1 set H323 ID set pin XXXXXXXXXX While calling card is set set password of chosen card while local type is set authentication type set password set rasport XXXX Set register port XXXX is range from 1024 through 65535 set g 931 port XXXX Set signal port XXXX is range from 1024 through 65535 set h245port XXXX Set control port XXXX is range from 1024 through 65535 set rtpport XXXX RTP port is the port transferring and receiving voice flow using UDP protocol XXXX is an even number between 1024 and 65535 set tos X Set TOS segment of IP head package in RTP digital follow X is range from 0 through 224 set localtype X This command used to set how IP phone log in gatekeeper X is ranged from 0 through 6 0 use phone number as E 164 and H323
41. t dial 1234 gt the Server light blinking now dial 192 168 1 100 press IP button for 10 seconds gt Power and Server lights alight gt then reboot the device AG 168V H323 Gateway User Manual V1 43 3 2 Configured by WEB Double click El icon to open the IE browser Input the IP address of the gateway into address bar Address 192 168 1 100 and then input password of the gateway into the following page Default password 1234 is ordinary password and super password is 12345678 With Debug set O disable please input super password while Debug is not set as O disable please input ordinary password Then click eem button The following configured page wills pop up Refer to Fig 3 1 please AG 168V H323 Gateway User Manual V1 43 iptype Network Settings static D ppp id local ip 192 168 1 100 subnet mask 266 266 266 0 dns bz 106 46 151 dns2 br 96 128 68 codeci codecd vad sudio frames jitter size dual mode use dialplan idd code inner line Audio Settings e728 DI codec era D een P ect nall cd eee z E 2 723 1 high rate E KT handset in 0 15 fis pstn first zl dual mode prefix fo Dial Plan Settings disable zl dial mmber semn pe idd prefix Im feissble zl inner line prefix pb forward mmber 95963 fad poveroff fwd alveys P fwd busy D use digitmap Ci use service nat traversal ras port rtp port local type H323 Protocol Settings Iv
42. the keyboard of the normal phone connecting to AG 168V FXS port and the IP key which can preset and enter into Setting mode operation as below Operation Function 1 press IP and pick up the handset connected to the FXS port of IP AG 168V voice prompt Local IP 2 with handset of FXS port s phone hung press default password then input the number of X IP button in order to set different network 1234 X IP connection X valued O staticIP 1 DHCP 2 PPPoE 3 modem 3 with handset of FXS port s phone hung press default password and 1234 IP press IP button enter setting mode 1234 XXX XXX XXX XXX 4 with handset of FXS port s phone hung press default password then IP input the IP address xxx xxxx xxx xxx press IP button Using the AG 168V H323 Gateway User Manual V1 43 button instead of 10 AG 168V H323 Gateway User Manual V1 43 3 1 2 Keypad setup Step by Step For example you want to set AG 168V s IP to static IP 192 168 1 100 you can Step 1 Change IP type to static pick up the handset gt you can see the status light alight gt dial 12340 gt the Server light blinking now gt press IP button for 10 seconds gt Power and Server alight gt then reboot the device Step 2 Set the static IP of the gateway pick up the handset gt you can see power and status light alight g
43. wd always C fwd busy call waiting fwd noanswer answer TET use digitmap V Fig 3 4 Dial Plan Setting e use dialplan Set whether use dial plan or use dial number by selecting the corresponding item in drop down list disable Do not use dial plan or dial number by selecting this item enable Use dial plan by selecting this item dialnum Use dial number by selecting this item With this item selected please enter the dial prefix into dial number field m prefix Use specially service by selecting this item Hotline Use Hotline function by selecting this item With this item selected please enter the hotline number into dial number field e dial number With dialnum selected in use dialplan drop down list please enter the dial prefix into this field according to requirement of log in server For example with eTalk card used enter 00 here e ddd code With enable or dialnum selected in use dialplan drop down list set area code according to E 164 dial rule For example Beiing 10 Shanghai 21 e idd code With enable or dialnum selected in use dialplan drop down list 19 AG 168V H323 Gateway User Manual V1 43 set country code according to E 164 dial rule For example China 86 U S A 1 e idd prefix With enable or dialnum selected in use dialplan drop down list set international call prefix according to E 164 dial rule such as 00 e ddd prefix With enable or dialnum selected in use dialplan drop
44. ween 10 and 65535 default value is 20 25 AG 168V H323 Gateway User Manual V1 43 e phone number The local phone number or username of this phone usually is allocated by system e account While calling card is set please type the account of chosen card into this field while md5 account item selected in local type dropdown list enter ID here while account is selected in local type dropdown list enter H323 ID here While prefix item selected in use dialplan dropdown list enter language indicating number card number and here such as 14589653185 e pin While calling card is set please type the password of chosen card into this field while md5 account item selected in local type dropdown list enter password here While prefix item selected in use dialplan dropdown list enter password and ff here such as 3185 e ras port Set the register port can be any number between 1024 and 65535 e q931 port Set the call signal port can be any number between 1024 and 65535 e h245 port Set the control port can be any number between 1024 and 65535 e rtp port RTP port is the port transferring and receiving voice packets 26 AG 168V H323 Gateway User Manual V1 43 using UDP protocol This is an even number between 1024 and 65535 e tos Set the TOS field of the IP header of the RTP packets The bigger this value is 0 the higher priority the packet is 224 e register ttl IP phone will sen
Download Pdf Manuals
Related Search