445F Ionizing Air Gun Instruction Manual
Contents
1. 445F lonizing Air Gun Instruction Manual Thank you very much for purchasing the lonizing air gun For your safety please read this Operating instruction carefully before operating And always keep this Manual within reach Frc the ionizing air gun is a kind of electric products and please comply the safety instruction for avoiding happening suddenness SECTION IT INSTRUCTION 1 1 Summary The 445F Ionizing Air Gun is used for removing static and dust of the inaccessible charged object and it can easily clear the parts and prevent it from being attached again after removing static Nozzle Spanner High voltage cord connecting with Inlet of the air the high voltage power supply 1 2 Parameters Z NOTE Never use it over the following parameter range otherwise it will damage the machine or hurt the human body Request of air supply Clean and dry air 0 1 0 7Mpa Connection with air supply a 6 X 8mm PU tube Request of high voltage TKVAC 40 50Hz 60Hz Effective distance of removing static Within 1000mm Standard length of high voltage cord 3 meter SECTION2 Installation N OTE the unit cannot be used in the danger zone such as use with flammable gas or solvent 2 1 Installation of the high voltage power supply High voltage power supply can be fixed on the wall or flat surface Detailed operation can refer to the installation part of operation manual of high voltage power supply 2 2 Grounding 1 F2. ce Z NOTE If the ion balance has deflection please adjust the ion balance adjustor on the high voltage power supply When the offset is negative adjust the adjustor anticlockwise and when the offset is positive adjust the adjustor clockwise 4 2 Regular maintenance For working effectively please keep the ion discharged needle clean Ion discharged needle can be cleaned by ordinary eraser Turn off the power switch put the eraser to placket of nozzle slowly press it down lightly and make the ion discharged needle prick into the eraser and rotate the eraser at the same time By this way the deposit in 10n discharged needle can be safely cleared Z NOTE Not to use any sharp and hard object to scrape the ion discharged needle since it will scathe the ion discharged needle Ion discharged needle should be kept as sharp as possible in order to keeping the best effect of using In case of ion discharged needle become blunt or scathed replace it
3. or having a necessary good ground between the ionizing air gun and the high voltage power supply connect the grounding cord to the grounding socket on the high voltage power supply and then screw down the screw cap 2 For avoiding the badness grounding of the three terminals socket one end of the grounding cord green amp yellow enclosing with the high voltage power supply connects with the grounding pole on the high voltage power supply and the other end connects to the earth 2 3 Connection with the high voltage cord Connect the plug of the high voltage cord of the ionizing air gun to the high voltage output socket on the high voltage power supply and tighten the screw by hand Please don t use any tool 2 4 Connection with the outer air source Connect the outer air source to the inlet of the ionizing air gun by a 4X 6mm PU tube The inlet is in the tail end of the ionizing air gun 2 5 Connection with the power cord The cord should be connected to a power supply of a rating voltage These using conditions are listed on the nameplate All power sockets should be the three terminal sockets with a good grounding system NOTE Do not to connect the power cord of power supply unit before all grounding line and power cord connections completed In order to use the ionizing air gun correctly and prevent operator from electric shock make sure there is a reliable grounding among the ionizing air gun high voltage po
4. to the charged object about several seconds for neutralizing the electrostatic left on the object All the parts of the charged object must be blew and make sure remove all the dust and static on it 3 If necessary test the balance voltage In case of balance voltage exceeds the normal range adjust the adjustor on the 2 High Voltage Power Supply 4 Turn off the power switch and the indicator lamp will be off high voltage output is stopped Z NOTE When the Power unit is turned on and off periodically in a cycle the on and off interval time should be one minute at least If the interval time is less than this the service life of the power unit may be shortened SECTION 4 INSPECTION AND MAINTENANCE 4 1 Checking of ionizing air gun 1 Recommend using a charge plate monitor for instance CPM374 to check the ion balance according to the Ionization Standard ANSI ESD STM3 1 2000 of the ESD Association 2 If there is only a charge plate monitor held by hands check the neutralizing performance periodically according to the following steps 1 Measure the static voltage of a charged object by a charge plate monitor 2 Turn on the power switch and the ionizing nozzle works normally Make the charged objects under the air outlet of ionizing bar and 15 30mm from it for several seconds 3 Measure the static voltage of the charged object again If the voltage obtained is within the eligible range it means that the unit is in good servi
5. wer supply and the earth Since the infectant air can block the nozzle or make it short circuit the air should be filtered cleanly before using Air pressure should be within 0 1 0 7Mpa SECTION 3 OPERATION Z NOTE The unit cannot be used in hazardous environment where it will be exposed to ignitable or corrosive materials gases or solvents It can be used after all of the electric and air supply connections have been completed 1 Turn on the switch of air source and adjust the air pressure and make it within a suitable range 2 High Voltage Power Supply has a switch with indicator lamp When turn on the switch the indicator lamp will be on and high voltage outlet will produce high voltage Ion discharged needle will ionizes the air and produces positive and negative ions When need to neutralize electrostatic on the charged object press the spanner of the ionizing air gun and then positive and negative ions will be exported along with airflow and neutralize static of charged objects in working area remove dust stuck to the charged objects prevent it from being attached again the emergence of electrostatic For getting the better effect of removing the dust and neutralize electrostatic firstly the ionizing air gun must be very near the charged object when working for blowing away all the dust Secondly move the ionizing air gun and make the nozzle of the gun away from the object about 200 300mm and keep the ionizing airflow blow
Download Pdf Manuals
Related Search