USER`S MANUAL TC200/ TC210/ TC300/ TC310 Series
Contents
1. The printer status from Diag Tool shows Ribbon Encoder Err Running out of ribbon The ribbon is installed incorrectly The LCD shows No Ribbon The printer status from DiagTool shows Out of Paper Running out of label The label is installed incorrectly Gap black mark sensor is not The LCD shows No Paper Calibrated The printer status from DiagTool shows Paper set properly Make sure label size is set properly Labels may be stuck inside The LCD shows Paper Jam ine printer mechanism The LCD shows Take Label Check if interface cable is well connected to the interface connector Not Printing device is well connected between host and printer The port specified in the 60 Gap black mark sensor is not Peel off function is enabled Check if wireless or Bluetooth Windows driver is not correct If using the Ethernet cable Plug the power cord in printer and outlet Switch the printer on Please close the print carriages Supply a new ribbon roll Please refer to the steps on section 3 3 to re install the ribbon Supply a new label roll Please refer to the steps on section 3 4 to reinstall the label roll Calibrate the gap black mark sensor Calibrate the media sensor Set media size correctly Remove the stuck label inside the printer mechanism If the peel off m2. 4 Plug the power cord into the AC power cord socket at the rear of the printer and then plug the power cord into a properly grounded power outlet USB interface Power supply Note Please switch OFF printer power switch prior to plug in the power cord to printer power jack 13 3 2 Open Close the Top Cover 1 Open the printers top cover by pulling the top cover open levers located on each side of the printer and lifting the top cover to the maximum open angle Atop cover support at the rear of the printer will engage with lower inner cover to hold the printer top cover 3 Hold the top cover and press the top cover support to disengage the top cover support with lower inner cover Gently close the top cover 14 3 3 Loading the Ribbon 1 Open the printers top cover by pulling the top cover open levers located on each side of the printer and lifting the top cover to the maximum open angle 2 Open the ribbon access cover and the media cover Note 1 In normal printing mode ribbon access cover can be opened while opens the top cover Ribbon access cover can be closed while top cover is open or close 2 In peeler and cutter mode please open the top cover then the ribbon access cover can be opened or closed 3 Insert the ribbon right side onto the supply hub Align the notches on the left side and mount onto the spokes 15 4 Insert the paper core right side o
3. Horizontal 1 mm max Printout bias 1 5 Ribbon Specifications Ribbon Specifications Ribbon outside diameter Max 40 mm OD Ribbon length 110 meter Ribbon core inside diameter 0 5 ID core Ribbon width 40 mm 110 mm Ribbon wound type Ink coated outside wound 1 6 Media Specifications Label length peeler mode 25 4 mm 152 4 mm 1 6 2 Operations Overview 2 1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping Please carefully inspect the packaging and printer upon receiving the bar code printer Please retain the packaging materials in case you need to reship the printer Unpacking the printer the following items are included in the carton One printer unit One Windows labeling software Windows driver CD disk One quick installation guide One power cord One auto switching power supply One USB interface cable If any parts are missing please contact the Customer Service Department of your purchased reseller or distributor 2 2 Printer Overview 2 2 1 Front View For TC210 series For TC200 series LCD display Menu button Feed button LED indicator Navigation button Ribbon access cover Top cover open lever SD card socket rae Se eS 5 Paper exit chute Recommended SD card specification For TC210 series SD card spec SD card capacity Approved SD card manufacturer V3 0 CLASS 10 UHS microSD 16GB Trans
4. Length i Advanced Mem Description gt gt Default Auto Calibration Printer will feed 2 to 3 gap labels to calibrate the sensor sensitivity N A automatically In case Auto calibration cannot apply to the media please use vanua Serup Manual setup function to calibrate the sensor sensitivity A Threshold Detect This option is used to set sensor sensitivity in fixed or auto Amo Maximum Length This option is used to set the maximum length for label calibration Advanced This function can set the minimum paper length and maximum gap bline length for auto calibrate the sensor sensitivity 49 6 6 Interface This option is used to set the printer interface settings 6 6 1 Serial Comm This option is used to set the printer RS 232 settings Mem Description Default Baud Rate Rate This This item is used to set the RS 292 baud rate Is used to set the This item is used to set the RS 292 baud rate 232 baud rate 9600 This item is used to set the RS 232 parity E Data Bits This item is used to set the RS 232 Data Bits NN Stop Bit s This item is used to set the RS 232 Stop Bits NN 50 6 6 2 Ethernet Use this menu to configure internal Ethernet configuration check the printer s Ethernet module status and reset the Ethernet module Status Menu Interface Ethernet DHCP Configure Static IP Mem Description NN Default
5. Use this menu to check the Ethernet IP address and MAC setting status N A This item is used to ON or OFF the DHCP Dynamic DHCP Host Configuration Protocol network protocol Use this menu to set the printer s IP address subnet mask and gateway 51 6 6 3 Bluetooth This option is used to set the printer Bluetooth settings Bluetooth Name Menu Interface Bluetooth Bluetooth PIN code tem Description _______________________ Default Bluetooth Name This item is used to set the local name for Bluetooth BT SPP Bluetooth PIN This item is used to set the local PIN code for 0000 Bluetooth 6 6 4 Wi Fi Operating Mode Menu Interface Wi Fi ScanAP DHCP Mem Description Default __ This item is used to set the operating mode of wireless local area networks to connect devices to the networks Note Infrastructure mode requires the use of an access point for this communication to take place Operating Ad hoc mode involves connecting a computer directly to another computer sean ap This item is used to scan the access point devise ONA DHCP This item is used to ON or OFF the DHCP Dynamic Host Configuration Protocol network protocol 52 6 7 File Manager This feature is used to check the printer available memory and file list DRAM Menu File Manager FLASH CARD Mem Description gt gt gt Use t
6. all regular heavy duty care label cutters DO NOT cut on media with glue KP 200 Plus keyboard display unit O oo KU 007 Plus programmable smart keyboard O ooo External roll mount with 3 core label spinde O Sleeve O External Bluetooth module serial interface O ooo External 802 11 b g n wireless module serialinterface O o Parallel port for TC210 TC310 series replace USB hos Realtime clock amp Buzzer LO 1 3 General Specifications General Specifications Physical dimensions 203 mm W x 191 5 mm H x 259 3 mm D TC200 TC300 2 2 kg TC210 TC310 2 3 kg Clamshell with Double walled plastic External universal switching power supply Input AC 100 240V 2 5A 50 60 Hz Output DC 24V 3 75A 90W Environmental Operation 5 40 C 41 104 F 25 85 non condensing condition Storage 40 60 C 40 140 F 10 90 non condensing ENVIO menta Comply with RoHS WEEE REACH concern 1 4 Print Specifications Print TC200 TC210 TC300 TC310 Specifications Print head 203 dots inch 300 dots inch resolution dots per inch mm 8 dots mm 12 dots mm Printing method Thermal transfer or direct thermal Dot size 0 125 x 0 125 mm 0 084 x 0 084 mm width x length 1 mm 8 dots 1 mm 12 dots Print speed Up to 6 IPS Up to 4 IPS inches per second Max 3 ips for peeler mode Max print width 108 mm 4 25 105 6 mm 4 15 Max print length 2 286 mm 90 ae ie o sl Vertical 1 mm max
7. m GLS BA 6D 0D BA ACODE 144 62 43 4F 148 38 1 31 34 39 26 1 0 2 6 32 30 26 57114387 20 22 35 PRINT 1 22 0D 04 1 2 6 a 3 2 on eS h 05 a 05 a na ir ana 0d y y y y Y Ob mh 0 j p b G DD TL THE 000 bd dd an ki m ae a a de Ao a ch a Note 1 Dump mode requires 4 wide paper width 2 Turn off on the power to resume printer for normal printing 37 5 3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults The only one exception is ribbon sensitivity which will note be restored to default Printer initialization is activated by the following procedures 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns green after 5 amber blinks Any green will do during the 5 blinks m The LED will be changed as following Green gt amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Release button Printer configuration will be restored to defaults as below after initialization O mm sec 5 ips 203DPI 76 mm sec 3 ips 300DPI Sensor Type Print Direction JO Reference Point 0 0 upper left corner Offset 38 5 4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor Please follow the steps as below 1 Turn off the p
8. and Calibrate the Gap SenSoF occcccccccnccccccnnccconnnnonancnnnnonons 40 NO BAG E 5 O A 41 6 EGO Menu FUNCION a i ee ccc eli alc alae Ted nas a 42 6 1 Emere Menlli a renden 42 6 2 Main Menu OVNIS We altas en O Oa tu NA GERARD DURA CAG 43 A ee AF HY ee A A 44 A ro pia o ee e RO Y O A OF AN o ee aa 46 8 9 SONS Ole un a is 49 8 9 MLCT aC AP E een ee on Scores eae a rn 50 6 6 1 cerial Comius a fas dali judia Dedico di a NW dd dy addo du O dda RA WA sek 50 06 6 2 CINCINCL sia a Sis dO GU GY na Yd GOD O 51 6 6 3 BlUEIOOIN ce 52 AA A cd A era ehh ei 52 6 7 LEE 0 9 LEN E a HT FFR NR EHO RE RU RE YF FON FR UY YU 53 ce MB Fo 0 Lt ei o nr ee HT Merk PR RR HY CS A FAN FFR RR a HN 54 6 91 Print Config dencia 54 6 8 2 Dump Mode unse ae le Fd OGOF 56 6 8 3 Print Head un 57 6 8 4 DISDIAY nassen energie 57 AO AA ats FEWR FEN AE ij Ln pulses me area EU RF NE GA Suan FFAN HYF FFF EYN 58 CO SON CO ad inneren eine 59 Za THOUDISSMOOLING ee ew aa a Be RIO a EA da 60 a AGINDO sas sarado ee fa EG y CF FFO ee Fae dee 63 REVIS RISTO Y uan GN e A RAN loci 65 vil 1 Introduction 1 1 Product Introduction Thank you very much for purchasing TSC bar code printer The TC200 210 series of thermal transfer desktop barcode printer label printer with its new smaller footprint offers the high performance that customers have come to expect from TSC Durable reliable and fast the TC200 210 generates 4 inch wide labels tags o
9. page Codepage 437 English US Codepage 737 Greek Codepage 850 Latin 1 Codepage 852 Latin 2 Codepage 855 Cyrillic Codepage 857 Turkish Codepage 860 Portuguese Codepage 861 Icelandic Codepage 862 Hebrew Codepage 863 French Canadian Codepage 864 Arabic Codepage 865 Nordic Codepage 866 Russian Codepage 869 Greek 2 Codepage 950 Traditional Chinese Codepage 936 Simplified Chinese Codepage 932 Japanese Codepage 949 Korean Codepage 1250 Latin 2 Codepage 1251 Codepage 1252 Codepage 1253 Codepage 1254 Codepage 1255 Codepage 1256 Codepage 1257 Codepage 1258 Cyrillic Latin 1 Greek Turkish Hebrew Arabic Baltic Vietnam OO Y gt mee eu ISO 8859 1 Latin 1 Western European ISO 8859 2 Latin 2 Central European ISO 8859 3 Latin 3 South European ISO 8859 4 Latin 4 North European ISO 8859 5 Cyrillic ISO 8859 6 Arabic ISO 8859 7 Greek ISO 8859 8 Hebrew ISO 8859 9 Turkish ISO 8859 10 Nordic ISO 8859 15 Latin 9 UTF 8 1 2 2 Printer Optional Features The printer offers the following optional features a User Dealer Factory Product option feature Peel off kit Paper length 1 6 Note This peel off module is supported for the thermal plain label only Regular cutter full cut guillotine cutter Paper thickness 0 06 0 19 mm Paper length 1 max length Max width 110 mm Note Except for the linerless cutter
10. Default Use this item to setup printing darkness The available setting is from O to 30 and the step is 1 You may need to adjust your density based on selected media 46 6 203dpi Print Speed ion this it to gyn cab speed Hi wo increase or 4 300dpi ecrease is 1 ips Available setting is from 2 to 6 3 600dpi Tear Off This item is used to fine as media stop location Available 000 setting value is from to or O to 9 This item is used to set the print mode There are 3 modes as below Print mode Printer Mode Tear Off Next label top of form is aligned to the print Tear Off head burn line location Peeler Off Enable the label peel off mode Enable the label cutter mode peen paperan a O to 9 This feature is used to print current printer available fonts list to the label The fonts stored in the printers DRAM Flash or N A optional memory card This feature is used to print current printer available images list to the label The images stored in the printer s DRAM Flash or N A optional memory card This feature is used to print current printer available formats list to the label The formats stored in the printers DRAM Flash or N A optional memor card ia rg Control Prefix This feature is used to set control prefix character Format Prefix This feature is used to set format prefix character Delimiter Char This feature is used to set delimiter character This option is used to set
11. IT 1 35 Print speed inch sec Print darkness Label size inch Gap distance inch Gap black mark sensor intension Code page Country code ZPL setting information Print darkness Print speed inch sec Label size Control prefix Format prefix Delimiter prefix Printer power up motion Printer head close motion Note ZPL is emulating for Zebra language RS232 serial port configuration PHYSICAL XXXX KBYTES AVAILABLE XXXX KBYTES Numbers of download files e e mm Total amp available memory space PAIN Print head check pattern E Dump mode Printer will enter dump mode after printing printer configuration In the dump mode all characters will be printed in 2 columns as following The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters It allows users or engineers to verify and debug the program SPEED 2 0 53 50 45 45 44 20 32 ZE 30 DENSITY 8 BA 44 45 4E 53 49 54 59 20 SET PEEL 0D GA 53 45 54 20 50 45 45 OFF DIRE 28 4F 46 46 GD GA 44 49 52 Sm e in O do E if mn REFERENCE 57 45 46 45 52 45 4E 43 45 20 0 0 SET Ba 43 ASCII Data UTTER ae Hex decimal data related to left 02 mm 6 5 8 30 32 20 60 6D 20 36 35 ZE 30 4 mm CLS 34 20 6D BD D DA 43 40 53 BD PAE ARTE 20 F 32 35 d d dodo SOROS mised 2 86 57114 32 2C 36 20 22 35 37 31 31 34 38T PRIN 33 38 54 22 0D DA 50 52 49 4E
12. NO MOTION lose bi HEAD CLOSE NO MOTION Note ZPL is emulating for Zebra language RS232 serial port configuration PHYSICAL XXXX KBYTES AVAILABLE XXXX KBYTES Numbers of download files Total amp available memory space PHYSICAL XXXX KBYTES AVAILABLE XXXX KBYTES men HH Print head check pattern Mh UU u Note Checking dot damage requires 4 wide paper width 55 6 8 2 Dump Mode Captures the data from the communications port and prints out the data received by printer In the dump mode all characters will be printed in 2 columns The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters It allows users or engineers to verify and debug the program Menu A Diagnostics Dump Mode DOWNLOA D y TESTI DAT 5 CT S DOWNLO AD E TES T4 DAT 5 CLS DOW NLOAD TE ST DAT Sets DO WNLOAD F nTEST4 DA me ACES DOWNLOAD TESTA D 217 Ss CES DOWNLOA D E TEST A DATOS CLS ASCII Data Hexadecimal data related to left column of ASCII data Note Dump mode requires 4 wide paper width 56 6 8 3 Print Head This feature is used to check print head s temperature resistance and bad dots 6 8 4 Display This feature is used to check LCD s color state 57 6 9 Advanced This feature is used to set the
13. Peel off Mode Option 1 Please refer to section 3 3 1 to load the media 2 Use Diagnostic Tool or LCD menu function to set the media sensor type and calibrate the selected sensor Note Please calibrate the gap black mark sensor before loading media in peel off mode to avoid paper jam Please calibrate the gap black mark sensor when changing media 3 Open the printer cover Pull the label through the front of the printer and take some labels off only leave the liner 4 Open the peel off module cover Feed the liner into peel off cover slot 5 Close the peel off module Use the Diag Tool or LCD menu function to enable the peel off mode Post Print Action Fef TEAR eference EET Direction CUTTER 23 24 Disengage the top cover support to close the top cover Printer is ready for peel off mode Press the FEED button to test Note This peel off module is supported for the thermal plain label only 3 4 4 Loading Media in Cutter Mode Option 1 Please refer to section 3 3 1 to load the media 2 Lead the media through the cutter paper opening 3 Close the printer cover 4 Use Diagnostic Tool or LCD menu function to set the media sensor type and calibrate the selected sensor 5 Use the DiagTool or LCD menu function to enable the cutter mode xl Cut Piece OFF Reference Ui Direction 6 Press the FEED button to test Note Please calibrate the gap black mark sens
14. Sensor Calibration Gap black mark sensor sensitivity should be calibrated at the following conditions 1 A brand new printer 2 Change label stock 3 Printer initialization Please follow the steps below to calibrate the ribbon and gap black mark sensor 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED becomes red and blinking Any red will do during the 5 blinks lt will calibrate the ribbon sensor and gap black mark sensor sensitivity The LED color will be changed as following order Green gt amber 5 red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Release button Note Please select gap or black mark sensor by sending GAP or BLINE command to printer prior to calibrate the sensor For more information about GAP and BLINE command please refer to TSPL2 programming manual 33 7 5 2 Gap Black Mark Calibration Self test and Dump Mode While calibrate the gap black mark sensor printer will measure the label length print the internal configuration self test on label and then enter the dump mode To calibrate gap or black mark sensor depends on the sensor setting in the last print job Please follow the steps below to calibrate the sensor 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED becomes amber a
15. TC200 TC210 TC300 TC310 Series THERMAL TRANSFER DIRECT THERMAL BAR CODE PRINTER USER S MANUAL Copyright Information 2015 TSC Auto ID Technology Co Ltd The copyright in this manual the software and firmware in the printer described therein are owned by TSC Auto ID Technology Co Ltd All rights reserved CG Triumvirate is a trademark of Agfa Corporation CG Triumvirate Bold Condensed font is under license from the Monotype Corporation Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners Information in this document is subject to change without notice and does not represent a commitment on the part of TSC Auto ID Technology Co No part of this manual may be reproduced or transmitted in any form or by any means for any purpose other than the purchaser s personal use without the expressed written permission of TSC Auto ID Technology Co Agency Compliance and Approvals EN 55022 Class B EN 55024 EN 60950 1 HC FCC part 15B Class B IN AS NZS CISPR 22 Class B Aus UL 60950 1 2nd Edition LISTED CSA C22 2 No 60950 1 07 2nd Edition EN 60950 1 GB 4943 1 GB 9254 GB 17625 1 Wichtige Sicherheits Hinweise 1 Bitte lesen Sie diese Hinweis sorgf ltig durch 2 Heben Sie diese Anleitung f r den sp teren Gebrauch auf 3 Vor jedem Reinigen ist das Ger t vom Stromentz zu trennen Verwenden Sie keine Fl ssig oder Aerosol
16. Top COVES ccccccccccsssseceeeceeeeeeeeeeeeeceeeeseeeeeeeeeeeeeeeeeesseaeeeeesseaeeeessaaeeeeessaaess 14 JS WOAGCINIG Ihe A 15 SA Ee NH HE Medi eier FR UF FE A TN 18 SA Loading Ihe Media eiu es GLOU a 18 3 4 2 External Label Roll Mount Installation Option eeuuu ieu Le LL Lien 21 3 4 3 Loading Media in Peel off Mode Option nn 23 3 4 4 Loading Media in Cutter Mode Option SSL rr AA AA ILL LL Leon 25 a A een 26 AI Start the Diagnostic FGol Se deis 26 ne send Yd ddd ne 27 4 3 Setting Ethernet by Diagnostic ToOOl ccccoconconccccconcnncncononcnnnnnonanonnnononancnnnnnnnnnnnnnnnnannnnnnnnonas 28 4 3 1 Using USB interface to setup Ethernet interface ccocooccocococconcconconconanonoos 28 4 3 2 Using RS 232 interface to setup Ethernet interface 29 4 3 3 Using Ethernet interface to setup Ethernet interface nenn 30 De POWER GUNES seele ee 32 5 1 Ribbon and Gap Black Mark Sensor CalibratiON ooconccnncccconcnononononcnonononanennnonnnnncnnnnnnnns 33 5 2 Gap Black Mark Calibration Self test and DUMP Mode cccccoccncccccccncococcnnocononnnoconnnnonononnnnonons 34 5 3 Printer IMMANZAUON EFE HF FFF FRAND FARF ein FO FFF HN AR 38 5 4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor 39 5 5 Set Gap Sensor as Media Sensor
17. cend Kingston The DOS FAT file system is supported for the SD card Folders files stored in the SD card should be in the 8 3 filename format The miniSD microSD card to SD card slot adapter is required For TC200 series VOSDHOCLASS44GB OO bO VO SDHO CLASS 6 mingD4GB The DOS FAT file system is supported for the SD card Folders files stored in the SD card should be in the 8 3 filename format The miniSD microSD card to SD card slot adapter is required 2 2 2 Interior view ea YY eee Se YS h A o Na 0 11 12 Ribbon rewind hub Ribbon rewind gear Gap sensor receiver Media holder Media holder locking switch Gap sensor transmitter Print head Ribbon supply hub Top cover support Media guide adjustment button Media guides Black mark sensor Platen roller 10 2 2 3 Rear View For TC210 series For TC200 series h a Ethernet interface USB interface USB host RS 232C interface Power jack socket Power switch 1 2 External label entrance chute o N 2 a PF o nM Parallel interface The interface picture here is for reference only Please refer to the product specification for the interfaces availability 11 2 3 Operator Control 2 3 1 LED Indication This printer has one three color LED indicator LED Color Green Solid Solid Green Solid This illuminates that the power is on and the device is This illuminates that the power is
18. ddress subnet mask and gateway for the on board Ethernet Interface ETHERNET USE COM LPT ETHERNET FEST Se top IP Address Model Name Status l 0018 82FF 0200 10 06 125 1033 50 Ready ee nen em PS Crevg0 00 18 11 C7 6790 100624 DP 5321 Ready 10 0 6 125 Port E a Discover Device Change IP Address Factory Default Web Setup 5 Click the Discover Device button to explore the printers that exist on the network 6 Select the printer in the left side of listed printers the correspondent IP address will be shown in the right side IP address Printer Name field 7 Click Change IP Address to configure the IP address obtained by DHCP or static r 10 0 10 33 subnet Mask 255 256 255 0 Gateway 0 0 10 252 Printer Name PS CFEM MAC Address 00 B 82 31 CF EO Set Printer Mame Set IF Cancel The default IP address is obtained by DHCP To change the setting to static IP address click Static IP radio button then enter the IP address subnet mask and gateway Click Set IP to take effect the settings Users can also change the Printer Name by another model name in this fields then click Set Printer Name to take effect this change Note After clicking the Set Printer Name or Set IP button printer will reset to take effect the settings Click Exit button to exit the Ethernet interface setup and go back to Diag
19. e pecwedseup SetPineiNamo ser Camel 98 4 3 2 Using RS 232 interface to setup Ethernet interface 1 Connect the computer and the printer with a RS 232 cable 2 Turn on the printer power icon 3 Start the Diagnostic Utility by double clicks on the 4 Select COM as interface then click on the Setup button to setup the serial port baud rate parity check data bits stop bit and flow control parameters 4 RS232 Setup COM Part ETHERNET Data Bits Parity Stop Bits Hardware Handshaking Software Handshaking Set 5 Click on the Ethernet Setup button from printer function of Printer Configuration tab to setup the IP address subnet mask and the gateway for the on board Ethernet Printer Function Calibrate Sensor ATC Setup Factory Default Reset Printer Print Test Page Configuration Page Dump Test Ignore ALITD EAS Exit Line Mode Password Setup Ethernet Setup C Static IP 10 0 10 33 Subnet Mask 255 255 2550 0 Printer Mame PS 31CFE0 MAC Address 0046 62 31 EFE0 Set Printer Hame Set IF Cancel 20 4 3 3 Using Ethernet interface to setup Ethernet interface 1 Connect the computer and the printer to the LAN 2 Turn on the printer power 3 Start the Diagnostic Utility by double clicks on the icon 4 Select Ethernet as the interface then click on the Setup button to setup the IP a
20. e ethanol to clean it e Please use 100 Ethenol or Isopropyl Alcohol DO NOT use medical alcohol which may damage the printer head e Regularly clean the print head and supply sensors once change a new media to keep printer performance and extend printer life 63 Continuous printing will cause printer motor overheat Printer will stop printing automatically about 10 15 minutes until motor is cooling down Please don t turn off power when printer pauses or the data transferred to printer buffer will be lost The maximum printing ratio per dot line is 15 for this printer To print the full web black line the maximum black line height is limited to 40 dots which is 5mm for 203 DPI resolution printer and 3 8mm for 300 DPI resolution printer only otherwise this may damage the power supply 64 Revise History Co O EZ 2015 10 21 Modify section 2 2 1 Recommended SD card specification 65 TSC The Smarter Choice TSC Auto ID Technology Co Ltd Corporate Headquarters 9F No 95 Minquan Rd Xindian Dist New Taipei City 23141 Taiwan R O C TEL 886 2 2218 6789 FAX 886 2 2218 5678 Web site www tscprinters com E mail apac_sales tscprinters com tech_support tscprinters com Li Ze Plant No 35 Sec 2 Ligong 1st Rd Wujie Township Yilan County 26841 Taiwan R O C TEL 4886 3 990 6677 FAX 886 3 990 5577
21. e is incorrect Method Use Curent Printer Setting Type Labels With Gaps Gap Height 3 00 mm Gap Offset 0 00 mm Media Handling Post Print Action Tear Off Mecurentce After Every Page label is incorrect The parameter Shift Y is incorrect The vertical offset setting in the driver is incorrect Interval Feed Offset 0 00 mm Position Adjustments ma Saw sm 62 8 Maintenance This session presents the clean tools and methods to maintain your printer 1 Please use one of following material to clean the printer m Cotton swab m Lint free cloth m Vacuum Blower brush m 100 Ethanol or Isopropyl Alcohol 2 Thecleaning process is described as following 1 Always turn off the printer before cleaning the print head 2 Allow the print head to cool for a minimum of one minute 3 Use a cotton swab and 100 Ethanol or Isopropyl Alcohol to clean the print head surface Clean the print head when changing a new label roll Print Head Print Head Print Head Element A ZED Z Element Head Cleaner Pen 1 Turn the power off Clean the platen roller when Platen Roller 2 Rotate the platen roller and wipe it changing a new label roll thoroughly with water to wipe It Sensor Compressed air or vacuum Monthly Exterior Wipe it with water dampened cloth interior Brush or vacuum e Do not touch printer head by hand If you touch it careless please us
22. ead up Sensor Gap Offset Reprint After Error Post Print Action ti amimur Length Cut Piece Gap Inten Reference Bline Inter Direction Offset Shift 2x shift y Continuous Inten Threshold Detection Printer Status Get Status COMI 9600 N 8 1 RTS 2015 7 8 EF 111100 96 4 2 Printer Function 1 Connect the printer and computer with a cable 2 Select the PC interface connected with bar code printer USB cable Other cable Interface Interface USB The default interface setting is USB Ck interface If USB interface is connected with printer no other ETHERNET settings need to be changed in the interface field 3 Click the Printer Function button to setup 4 The detail functions in the Printer Function Group are listed as below Printer Function Function Description o EEE Calibrate Sensor Setup group media sensor feld Ethemet Setup setup the IP address subnet mask gateway for pmelneloetip the on board Ethernet O RTESewp RTC Setup Synchronize printer Real Time Clock with PC En Factory Default pra nel and restore the settings to Reset Printer Reset Printer Reboot printer Print Test Page Print Test Page Print a test page Configuration Page Configuration Page Print printer configuration Dump Text Dump Text To activate the printer dump mode Ignore AUTO BAS Ignore AUTO BAS Ignore the downloaded AUTO BAS program Exit Line Mode Exit Line Mode Exit line mode _ Pess
23. edia is loaded incorrectly Reload the supply Dust or adhesive Clean the print head accumulation on the print Clean the platen roller head Adjust the print density and print speed Print density is not set Run printer self test and check the print Poor Print Quality properly head test pattern if there is dot missing in Print head element is the pattern damaged Change proper ribbon or proper label Ribbon and media are media incompatible The release lever does not latch the print The print head pressure is head properly not set properly No print on the label Plug in the connect cable correctly The connector is loose Remove the label Cutter is not working Cutter jam Make sure the thickness of label is less Cutter PCB is damaged than 0 19 mm Replace a cutter driver IC board Can t downloading the file to memory FLASH The space of memory is full Delete unused files in the memory DRAM CARD SD card is damaged Use the supported capacity SD card SD card is unable to use SD card doesn t insert Please refer to section 2 2 1 correctly Insert the SD card again Missing printing on the left or right side of label The print head is dirty Clean the print head Gray ine Plan IRO The platen roller is dirty Clean the platen roller 61 Wrong label size setup Set the correct label size The printer is in Hex Dump mode The RS 232 setti
24. g Green gt amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Release button 4 Printer will be interrupted to run the AUTO BAS program 41 6 LCD Menu Function 6 1 Enter the Menu Press the Menu button to enter the main menu Use the Cross button to select the item on main menu The selected item will turn red Press the Feed button to enter the setting list Note This LCD function is for TC210 310 series MY 50 10 0 10 125 03 30 AM Model name Firmware version Menu m Sensor Interface Advanced Service Back Select Back Select TSPL File Manager Diagnostic 42 6 2 Main Menu Overview There are 8 categories for the main menu You can easy to set the settings of printer without connecting the computer Please refer to following sections for more details AS 6 3 TSPL2 This TSPL2 category can set up the printer settings for TSPL2 Speed Density None Direction Batch Mode Print mode Peeler Mode Offset Cutter Mode Menu TSPL Shift X Cutter Batch Shift Y Reference X Reference Y Code Page UU Country Item Description _ S Speed Use this item to setup print speed N A Use this option to setup printing darkness The available setting is Density from 0 to 15 and the step is 1 You may need to adj
25. g automatically about 10 15 minutes until motor is cooling down Please don t turn off power when printer pauses or the data transferred to printer buffer will be lost The maximum printing ratio per dot line is 15 for this printer To print the full web black line the maximum black line height is limited to 40 dots which is 5mm for 203 DPI resolution printer and 3 3mm for 300 DPI resolution printers only otherwise this may damage the power supply iv Contents 1 nir Od uc HO i O EI GN RR eee 1 121 PFOdUGL Introduelion series 1 ALS AAA eltern A 2 1 2 1 Printer Standard Features oooccccccconcconccoconcconcconnnncnnnnonnnnnnnnnnnnnncnnnnonnnnrnnnnnnnnncnnnnnnnns 2 1 2 2 Printer Optional Features cc 0c ccccceccessecececcceseseenscceseeeeescceeeseesteceseeeesscoseesensseoess 4 o G eneral pecilic AU ONS ce see 5 Mc TL E AS a let eee 5 1 SRD DO No DECIICANOIS A CW inne use 5 IO Media pecto INS Gotas Dee te eae aa en Hu Cl 6 2 Operations OVENVICW ee etn ase LO RY aia 7 2 kUnpackng ano Aspect O a a a A O OR GAL 7 2 2 ma i ge ONEVIEW ee He era FR FD FY HR 8 272 1 EFONE VIEW erro RR CR A HF Y REN CR NN HI 8 2 2 2 INIETIOR VIEW RS sk cect tt oi HF 10 2 2 3 Rear VIeW en En ED GO GOD DAE TE essa CON GOG 11 oa Do gai a ae ON Ol ee ee a DR nee ere 12 2 321 LED INGIC AON to a sant O De a UG 12 2 3 2 BUON FUNCION ian ia 12 E QUI HE A a a 13 3 Seting UP Ne DIME nasse A aa a da 13 3 2 Open Close the
26. his menu to show delete and run BAS the files saved in the printer DRAM memory Use this menu to show delete and run BAS the files saved in FLASH the printer Flash memory Use this menu to show delete and run BAS the files saved in CARD the printer Card memory 53 6 8 Diagnostics Menu Diagnostics 6 8 1 Print Config Print Config Dump Mode Print Head Display Sensor This feature is used to print current printer configuration to the label On the configuration printout there is a print head test pattern which is useful for checking if there is any dot damage on the print head heater element Menu Diagnostics Self test printout INTENSION CODEPAGE COUNTRY gt XXXXXX FIRMWARE CHECKSUM S N TCF DATE TIME NON RESET 1 X XX XXXXXXXX XXXXXXXXXXX NO 1970 01 01 INCH 00 INCH INCH 54 Print Config Model name F W version Firmware checksum Printer S N TSC configuration file System date System time Printed mileage meter Cutting counter Print speed inch sec Print darkness Label size inch Gap distance inch Gap black mark sensor intension Code page Country code ZPL setting information Print darkness DRRKNESS E Print speed inch sec SPEED l WIDTH 4 Label size TILDE Control prefix Format prefix CARET Delimiter prefix DELIMITER 2CH POWER UP
27. mordSeup Password Setup Set the password to protect the settings Note For more information about Diagnostic Tool please refer to the diagnostic utility quick start guide in the CD disk Utilities directory 27 4 3 Setting Ethernet by Diagnostic Tool The Diagnostic Utility IS enclosed in the CD disk Utilities directory Users can use Diagnostic Tool to setup the Ethernet by RS 232 USB and Ethernet interfaces The following contents will instruct users how to configure the Ethernet by these three interfaces 4 3 1 Using USB interface to setup Ethernet interface oO gt Connect the printer and computer with USB cable Turn on the printer power switch Start the Diagnostic Utility by double clicking on the DiseToolexe icon The Diagnostic Utility default interface setting is USB interface If USB interface is connected with printer no other settings need to be changed in the interface field Interface use Click on the Ethernet Setup button from Printer Function group in Printer Configuration tab to setup the IP address subnet mask and gateway for the on board Ethernet Printer Function Calibrate Sensor Eihemetsetup Ethernet Setup ATC Setup IF Setup Factory Default State IP Reset Printer Print Test Page 10 0 10 33 Configuration Page 299 295 255 10 0 10 252 Dump Text Printer Mame P5 S1LFED Ignore AUTO EAS MAL Address UO 16 6 31 CF EU Exit Line Mod
28. nd blinking Any amber will do during the 5 blinks m The LED will be changed as following order Green gt amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Release button 4 It calibrates the sensor and measures the label length and prints internal settings then enter the dump mode Note Please select gap or black mark sensor by Diagnostic Tool or by GAP or BLINE command prior to calibrate the sensor For more information about GAP and BLINE command please refer to TSPL2 programming manual 34 E Self test Printer will print the printer configuration after gap black mark sensor calibration Self test printout can be used to check if there is any dot damage on the heater element printer configurations and available memory space Self test printout gt MODEL XXXIX cerrar F W version FIRMWARE X XX CHECKSUM XXXXXXXX Firmware checksum S N XXXXXXXXXXX Printer S N TCF NO Configuration file TIME 00 04 18 S ystem time NON RESET 110 m TPH RESET 110 m TPH a no meter NON RESET CUT utting counter RESET Q CUT 5 8 4 00 INCH 4 00 INCH 0 00 INCH INTENSION 5 CODEPAGE COUNTRY DARKNESS SPEED WIDTH TILDE CARET DELIMITER POWER UP HEAD CLOSE 4 IPS 4 00 INCH TEH 5 SEH 2CH NO MOTION NO MOTION BAUD 9600 PARITY NONE DATA BIT 8 STOP B
29. ng is incorrect Turn off and on the printer to skip the dump mode Re set the Rs 232 setting Irregular printing If the label is moving to the right side Label feeding is not stable The media guides do not please move the label guide to left skew when printing touch the edge of the media If the label is moving to the left side please move the label guide to right Label size is not specified Check if label size is setup correctly a AN Geel Calibrate the sensor by Auto Gap or properly Manual Gap options The a Escoria covered Clear the GAP Black mark sensor by blower with dust Printhead pressure is incorrect Ribbon installation is Wrinkle Problem incorrect Media installation is incorrect Print density is incorrect Media feeding is incorrect RTC time is incorrect when Check if there is a battery on the main Calibrate the sensor sensitivity again Set the correct label size and gap size Use DiagTool to fine tune the parameter of Shift Y If using the software BarTender please set the vertical offset in the driver FL ENESKFERTE HE Skip labels when printing Please set the suitable density to have good print quality Make sure the label guides touch the edge of the media guide Page Setup Graphics Stock Options About Media Settings Media sensor sensitivity is not set properly The printing position of small Label siz
30. nostic Tool main screen Factory Default button This function will reset the IP subnet mask gateway parameters obtained by DHCP and reset the printer name Web setup button Except to use the Diagnostic Utility to setup the printer you can also explore and configure the printer settings and status or update the firmware with the IE or Firefox web browser This feature provides a user friendly setup interface and the capability to manage the printer remotely over a network 31 5 Power on Utilities There are six power on utilities to set up and test printer hardware These utilities are activated by pressing FEED button then turning on the printer power simultaneously and release the button at different status of LED Please follow the steps below for different power on utilities 1 Turn off the printer power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED indicates with different status color for different functions Power on utilities The LED color will be lt as following pattern Green Amber Amber 5 blinks 5 blinks Ribbon sensor calibration Release and gap black mark sensor calibration Gap black mark sensor Release calibration Self test and enter dump mode Set black mark sensor as Release media sensor and calibrate the black mark sensor Set gap sensor as media Release sensor and calibrate the gap sensor ae 5 1 Ribbon and Gap Black Mark
31. nto the rewind hub Align the notches on the left side and mount onto the spokes 5 Stick the ribbon onto the ribbon rewind paper core 6 Turn the ribbon rewind gear until the ribbon plastic leader is thoroughly wound and the black section of the ribbon covers the print head 16 7 Close the ribbon access cover and the top cover Loading path for ribbon Ribbon rewind roll J supply roll 17 3 4 Loading the Media 3 4 1 Loading the Media 1 Open the printer top cover by pulling the tabs located on each side towards the front of the printer then lift the top cover to the maximum open angle 2 Separate and hold open the media holders 3 Place the roll between the holders and close them onto the core 18 19 4 Press down the media holder lock switch to hold the label roll firmly 5 Place the paper printing side face up through the media sensor and place the label leading edge onto the platen roller Move the media guides to fit the label width by turning the guide adjuster knob 6 Disengage the top cover support and close the top cover gently 7 Use Diagnostic Tool or LCD menu function to set the media sensor type and calibrate the selected sensor Note Please calibrate the gap black mark sensor when changing media Please refer to the diagnostic utility guick start guide for more information Start the Diagnostic tool gt Select the P
32. o Head open sensor Oo o Automatic medati hon sensorseecing O o AmB Fat memory 6 128 MB Fast memos O WM O GAMBODREDAM SD card reader tor memory expansion upea O SD cara reader tor memory expansion upoe O RS 202 inerace Maxon O O USB 20 mertace Fulspeedmode O USB 20 med Hispeedmode O Internal Ethernet print server 10 100 Mbps o interface Parallel SPP mode _ o Standard industry emulations right out of the box o o including Eltron and Zebra language support Internal 8 alpha numeric bitmap fonts Oo bh o Fonts and bar codes can be printed in any one of i o o the four directions O 90 180 270 degree Internal Monotype Imaging true type font engine with one CG Triumvirate Bold Condensed scalable font Downloadable fonts from PC to printer memory Oo bh o Unicode UTF8 support o fo Bar code graphics image printing Supported bar code Supported image 1D bar code 2D bar code BITMAP Code128 CODABLOCK BMP PCX subsets A B C F mode Max 256 Code128UCC DataMatrix colors EAN128 Maxicode graphics Interleave20f PDF 417 5 Code 39 Aztec Code 93 EAN MicroPDF417 13 EAN 8 OR code Codabar RSS Barcode POSTNET GS1 Databar UPC A UPC E EAN and UPC 2 5 digits MSI PLESSEY China Post ITF14 EAN14 Code 11 TELPEN PLANET Code 49 Deutsche Post Identcode Deutsche Post Leitcode LOGMARS Supported code
33. odule is installed please remove the label If there is no peel off module in front of the printer please switch off the printer and install it Check if the connector is plugging correctly Re connect cable to interface or change a new cable f using serial cable Please replace the cable with pin to pin connected Check the baud rate setting The default baud rate setting of printer is 9600 n 8 1 Check if the Ethernet RJ 45 connector green LED is lit on Check if the Ethernet RJ 45 connector amber LED is blinking Check if the printer gets the IP address when using DHCP mode Check if the IP address is correct when using the static IP address Wait a few seconds let the printer get the communication with the server then check the IP address setting again Please reset the wireless device setting Select the correct printer port in the driver Print head s harness connector is not well connected with printheat Turn off the printer and plug the connector again Check your program if there is a command PRINT at the end of the file and there must have CRLF at the end of each command line Follow the instructions in loading the Label or ribbon is loaded not media and ribbon correctly Ribbon and media are not compatible Use wrong type paper or Verify the ribbon inked side ribbon The print density setting is incorrect Clean the print head Ribbon and m
34. of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 111 Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 Cet appareil numerique de la classe B est conforme a la norme NMB 003 du Canada Note Continuous printing will cause printer motor overheat Printer will stop printin
35. on and the device is ready to use to use Green Flash This illuminates that the system is downloading data from PC to memory or the printer is paused Amber This illuminates that the system is clearing data from printer Red Solid This illuminates printer head open cutter error Red Flash This illuminates a printing error such as head open paper empty paper Jam or memory error etc 2 3 2 Button Function For TC200 series e Feed button When the printer is ready press the button to feed one label to the beginning of next label When the printer is printing press the button to pause a print job When the printer is paused the power LED will blink green Press the button again to continue the printing job For TC210series e Feed button When the printer is ready press the button to feed one label to the beginning of next label When the printer is printing press the button to pause a print job When the printer is paused the power LED will blink green Press the button again to continue the printing job When printer enter the menu press the button to enter select cursor located item e Menu button Enter the menu Exit from a menu or cancel a setting and return to the previous menu e Navigation button Scroll the menu list 12 3 Setup 3 1 Setting up the printer 1 Place the printer on a flat secure surface 2 Make sure the power switch is off 3 Connect the printer to the computer with the provided USB cable
36. or when changing media 25 4 Diagnostic Tool TSC s Diagnostic Utility is an integrated tool incorporating features that enable you to explore a printer s settings status change a printer s settings download graphics fonts and firmware create a printer bitmap font and send additional commands to a printer With the aid of this powerful tool you can review printer status and setting in an instant which makes it much easier to troubleshoot problems and other issues 4 1 Start the Diagnostic Tool Features tab Printer functions Printer Status 1 Double click on the Diagnostic tool icon to start the software 2 There are four features Printer Configuration File Manager Bitmap Font Manager Command Tool included in the Diagnostic utility ia Diagnostic Tool 1 63 Language Unit EL English inch mm USE Y Setup Interface Printer Configuration File Manager Bitmap Font Manager Command Tool Frinter Function Printer Configuration Printer Information Calibrate Sensor VEN Po Cutting Counter B qdo Ethernet Setup Serial No Mileage Km Check Sum ATC Setup Factory Default Reset Printer Print Test Page Configuration Page Dump Text lgnore AUTO EAS Exit Line Mode Password Setup Common Z D RS 232 Wireless Speed Ribbon Density Paper width Ribbon Sensor Ribbon Encoder Err Faper Height Code Fage Media Sensor Country Code Printer setup Gap H
37. ower switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns green amber after 5 green blinks Any green amber will do during the 5 blinks m The LED will be changed as following Green gt amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Release button 39 5 5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor Please follow the steps as below 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns red amber after 5 green amber blinks Any red amber will do during the 5 blinks m The LED will be changed as following Green gt amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Release button 40 5 6 Skip AUTO BAS TSPL2 programming language allows user to download an auto execution file to flash memory Printer will run the AUTO BAS program immediately when turning on printer power The AUTO BAS program can be interrupted without running the program by the power on utility Please follow the procedures below to skip an AUTO BAS program 1 Turn off printer power 2 Press the FEED button and then turn on power 3 Release the FEED button when LED becomes solid green m The LED will be changed as followin
38. printer LCD settings Display Brightness Menu Advanced Date amp Time Language Mem Description gt gt Display Brightness This item is used to setup the brightness for display Date amp Time This item is used to setup the date and time on display This item is used to setup the language on display 58 6 10 Service This feature is used to restore printer settings to defaults and checking information for printer Initialization Menu Service Printer Information Contact Us Mem Description gt gt gt Initialization This feature is used to restore printer settings to defaults Printer This ene is used to check the printer s serial number printed Information mileage m printed labels pcs and cutting counter Contact Us dia is used to check the contact information for tech support 59 7 Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer If the printer still does not function after all suggested solutions have been invoked please contact the tech support service of your purchased reseller or distributor for assistance Possible Cause Recovery Procedure Power indicator does not illuminate The power cord is not properly connected The printer status from Diag Tool shows Head Open The printer head is open The LCD shows Carriage Open
39. r receipts at up to 6 ips offering a price performance combination that is unmatched by other desktop thermal barcode printers on the market As with all TSC printers the TC200 210 series features the TSPL EZ printer control language which is fully compatible with other TSC printer languages while supporting TPLE Translation Printer Language Eltron and TPLZ Translation Printer Language Zebra The languages automatically decipher and translate the format of each label as it is sent to the printer TSPL EZ also features internal scalable True Type fonts based on the Monotype font engine which are typically found only in more expensive printers Applications e Point of sale e Product marking e Receipt coupon printing e Compliance labeling e Asset tracking e Document management e Shipping receiving e Inventory control e Specimen labeling e Patient tracking 1 2 Product Features 1 2 1 Printer Standard Features The printer offers the following standard features Tremas venster or rect tners T operating buton and 1 LED wih Score O S operating buttons and LED win3 colors 320 x 240 TFT LCD UI of operating menu 32 bit RISC high performance processor Atmel 9260 210 MHz 32 bit RISC high performance processor Atmel NE 9G25 400 MHz Center alignment holder with spiral spring Gap transmissive sensor Fixed center of offset 4 O from center NE oo Dom Do a Ze Ze Rbonercodersensor O
40. reiniger Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung 4 Die NetzanschluB Steckdose soll nahe dem Ger t angebracht und leicht zug nglich sein 5 Das Ger t ist vor Feuchtigkeit zu sch tzen 6 Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Besch digungen hervorrufen 7 Beachten Sie beim Anschlu ans Stromnetz die Anschlu Bwerte 8 Dieses Ger t kann bis zu einer Au entemperatur von maximal 40 C betrieben werden i 1 HAZARDOUS MOVING PARTS IN CUTTER MODULE KEEP FINGER AND OTHER BODY PARTS AWAY 2 THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY CR2032 INSTALLED RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE 3 DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER INSTRUCTIONS CAUTION Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions VORSICHT Explosionsgefahr bei unsachgem en Austaush der Batterie Ersatz nur durch denselben oder einem vom Hersteller empfohlenem hnlichen Typ Entsorgung gebrauchter Batterien nach Angabren des Herstellers WARNUNG GEF HRLICHE BEWEGLICHE TEILE FINGER UND ANDERE K RPERTEILE FERNHALTEN B 7 7 7232 245417 7 111771822 243 3 a SANJANE EE RES FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15
41. rinter Configuration tab gt Click the Calibrate Sensor button Please refer to the section 6 for LCD menu function Loading path for media Gap sensor Black mark Media holder sensor Platen roller 20 3 4 2 External Label Roll Mount Installation Option 1 Attach an external paper roll mount on the bottom of the printer N Insert a 3 label spindle into a paper roll And install it on the external paper roll mount 3 Open the printer s top cover and separate the media holders to fit the media width Press down the media holder lock switch to fix the media holder 21 4 Feeds the media through the rear external label entrance chute And place the paper printing side face up through the media sensor and place the label leading edge onto the platen roller Move the media guides to fit the label width by turning the guide adjuster knob 5 Disengage the top cover support and close the top cover gently 6 Use Diagnostic Tool or LCD menu function to set the media sensor type and calibrate the selected sensor Note Please calibrate the gap black mark sensor when changing media Please refer to the diagnostic utility quick start guide for more information Start the Diagnostic tool gt Select the Printer Configuration tab gt Click the Calibrate Sensor button Please refer to the section 6 for LCD menu function 22 3 4 3 Loading Media in
42. the action of the media when you turn on the printer Media Power Up determine length and feed label Length Printer determine length and feed label Printer will not move media This option is used to set the action of the media when you close jn the print head Head Close Printer will advance one label determine length and feed label This option is used to E ando o eee print position vertically on the label The Rit pr a A is 120 to 120 dots Left Position This option is used to adjust print position horizontally onthe 0000 Label Top 47 label The range is 9999 to 9999 dots Reprint Mode When reprint mode is enabled you can reprint the last label Disabled printer by pressing UP button on printer s control panel Selects the bitmap scaling factor The first number is the original Format Convert dots per inch dpi value the second the dpi to which you would like to scale Note If printing from enclosed software driver the software driver will send out the commands which will overwrite the settings set from the panel 48 6 5 Sensor This option is used to calibrate the selected sensor We recommend calibrate the sensor before printing when changing the media Gap Auto f Calibration Black Mark Continuous Gap Manual Setup Black Mark Menu Sensor Continuous Threshold Auio Detect Fixed Maximum
43. ust your density based on selected media The direction setting value is either 1 or 0 Use this item to setup the printout direction Direction UON ISA This item is used to set the print mode There are 5 modes as below Printer Mode None Next label top of form is aligned to the print head burn aii l a line location Tear Off Mode Batch Mode Once image is printed completely label gap black mark will be fed to the tear plate location for tear away 44 Peeler Mode Enable the label peel off mode Cutter Mode Enable the label cutter mode Cutter Batch Cut the label once at the end of the printing job This item is used to fine tune media stop location Available setting value is from to or O to 9 Shift X This item is used to fine tune print position Available setting value is Shift Y from to or 0 to 9 Reference X This item is used to set the origin of printer coordinate system horizontally Reference Y and vertically Available setting value is from 0 to 9 Code page Use this item to set the code page of international character set Country Use this option to set the country code Note If printing from enclosed software driver the software driver will send out the commands which will overwrite the settings set from the panel 45 6 4 ZPL2 This ZPL2 category can set up the printer settings for ZPL2 Mem Description O
Download Pdf Manuals
Related Search