See the Manual - Futureshop.co.uk
Contents
1. source and 3DTV Display 3D content can now be displayed on the 3DTV Display along with audio embedded in the HDMI signal OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE EXTENDER FOR HDMI 3DTV CAT 5 or CAT 6 cables should not exceed 330 feet 100 meters Shielded STP CAT 5 or CAT 6 is recommended However unshielded UTP CAT 5 or CAT 6 is acceptable NOTE Shielded cable has an advantage by providing immunity to Electromagnetic Interference EMI from cell phones and A C motors The Extender for HDMI 3DTV features the ability to generate compatible EDID and Hot Plug signals for troubleshooting purposes when dealing with difficult interfacing issues between Source devices and Displays Please see the section on pages 9 10 for troubleshooting purposes FEATURES Features Extends HDMI at 1080p up to 330 ft 100 m e Supports HDMI 1 3 with 3DTV Supports high bit rate multi channel audio formats Dolby TrueHD DTS Master Audio embedded in the HDMI 1 3 signal e Internal External EDID Management e Locking power connectors e Built in IR backchannel allows IR remote control of Source devices e Metal enclosure improves RF shielding e All digital signal transmission for zero signal loss e Optional IR Blaster allowing IR remote control of Hi Def source devices from the remote viewing location e This product is HDMI and HDCP compliant HDMI 1 3 Features e 225 MHz up to 12 bit2. Gefen TOOLBGX Extender for HOM SDTV GTB HDMI 3DTV BLK User Manual Extender for Extender for HDMI SDTV S HDMI SDTV R www gefentoolbox com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefentoolbox com support gefentoolbox com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice GefenToolbox Extender for HDMI 3DTV is a trademark of Gefen LLC 2010 Gefen LLC All Rights Reserved HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries All trademarks are the property of their respective owners Rev X4 O a A O0 Oo oOo N CONTENTS Introduction Operation Notes Features Sender Unit Layout Sender Unit Descriptions Receiver Unit Layout Receiver Unit Descriptions Connecting and Operating The Extender For HDMI 3DTV DIP Switch Configuration Network Cable Wiring Diagram Wall Mounting Instructions Specifications Warranty INTRODUCTION Congratulations on your purchase of the Extender for HDMI 3DTV Your complete satisfaction is very important to us GefenToolbox GefenToo
3. YUV 4 4 4 1080p60 e Dolby TrueHD amp DTS Master Audio e Deep Color Support x v Color e Lip Sync Pass Through e CEC Pass Though Package Includes 1 Extender for HDMI 3DTV Sender Unit 1 Extender for HDMI 3DTV Receiver Unit 2 6 ft Locking HDMI cables 2 5V DC Locking Power Supplies 1 User Manual SENDER UNIT LAYOUT Left Extender fo HDMI SDTV V R Right SENDER UNIT DESCRIPTIONS CAT 5 Output Jack Connects the Sender to the Receiver unit using CAT 5 cabling IR Blaster Port Connect an IR Blaster cable from this port to the Hi Def source to control the source from the viewing location IR Blaster not included 5V DC Locking Power Connector Connect the included 5V DC locking power supply to this connector Only use the power supply shipped with this unit Power Indicator This LED will turn bright red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supply has been connected to an available wall outlet Locking HDMI Port Connect a 3D Hi Def source device to this HDMI port Please see the Features section on page 3 for supported HDMI 1 3 features RECEIVER UNIT LAYOUT Left Extender for HDMISDTV R Right RECEIVER UNIT DESCRIPTIONS IR Extender Port Connect an IR extender to this port CAT 5 Input Port Connects the Receiver to the Sender unit using CAT 5 cabling IR Sensor Receives signals from the 3D s
4. ay device EDID features newer than HDMI 1 3 are removed when the display is read This provides a general EDID which is compatible with more displays DIP 2 Hot Plug Detect ON HPD Pass Through HPD follows upstream HPD towards the source The HPD signal will reflect the connection status between the display device and the source device If the source or display is temporarily disconnected then reconnected there will be a delay of 20 30 seconds before the A V content is restored to the display OFF default HPD Always High e The HPD signal remains high regardless of the downstream HPD state If the source or display device does not properly handle HPD no picture after connecting reconnecting source or display set this DIP switch to the OFF position DIP 3 Supports DVI Connections ON e Ifa DVI connection is used set DIP 3 to the ON position OFF default e If HDMI is connected set DIP 3 in the OFF position DIP switch is only functional when DIP switch 1 is set to OFF 10 NETWORK CABLE WIRING DIAGRAM Gefen recommends the TIA EIA 568 B wiring option Please adhere to the table below when field terminating cable for use with Gefen products mn cos 6 Gen pp 8 Brown 12345678 CAT 5 CAT 5e and CAT 6 cabling comes in stranded and solid core types Gefen recommends using solid core cabling CAT 6 cable is also recommended It is recommended to use one continuous run from one e
5. lbox is a unique product line catering to the growing needs for innovative home theater solutions We specialize in total integration for your home theater while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line and hope you find your solutions Don t see what you are looking for here Please call us so we can better assist you with your particular needs The GefenToolbox Extender for HDMI 3DTV The GefenToolbox Extender for HDMI 3DTV extends HDMI and 3D content including multi channel digital audio at resolutions of up to 1080p Full HD up to 330 feet 100 meters from any Hi Def source using one CAT 5 cable This product also provides an IR backchannel to control AV sources using the same CAT 5 cable extension Using this remote IR back channel with an optional IR Blaster you can point to any one of the of the AV device sources by pointing towards the IR sensor to control Hi Def sources as if they were located in the same room or proximity to the display How It Works Connect the GefenToolbox Extender for HDMI 3DTV sender unit to the 3D Hi Def source using the supplied HDMI cable Connect the receiver unit to the 3DTV Display Use a single CAT 5 cable up to 330 feet 100 meters in length to connect the sender and the receiver units Connect the locking power supplies to both sender and receiver units and apply power to the 3D Hi Def
6. nd to the other In some cases connecting through a patch might not work 11 WALL MOUNTING INSTRUCTIONS The GefenToolbox Extender for HDMI 3DTV should be mounted vertically on a wall or inside outside a cabinet with wood drywall screws as shown in the diagram above There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the HDMI cable For installation on a drywall surface use a 6 drywall screw When installing it is recommended to use the center hole on a stud 12 SPECIFICATIONS Video Amplifier Bandwidth ersnnvreronvonnnvnrnnnvnvrnrervrnnrvnrenrenernrrrnrnerensnneenn 225 MHz Input Video Signalkauarmasdsnnniau dn rr penitent dina 1 2 Vp p Aput DDC Signal saae slaa uret 5 V p p TTL Maximum Video Resolution 1080p supports 3D HDMI signals HDMI Input Connector asrarvrvrvrnvvrerrnrnvrnenrnesvrnenvnsrrrnenvnsrnveennn Type A 19 pin F Link Connector iets utsatte RJ 45 Shielded Power indicator nica cid ae aia a eee AL eee LED red DIMENSIONS iia doit ctas 4 5 L x 3 25 W x 1 0 H Power SUPPLY iii 5V DC Power Consumption ccccescececeeseeeeeeeeeeeseeeseeeeeeeseeeeeeesaaes 10 W per unit max Operating Temperature nrnrnnrnnnnnvnnnnrnonvnnnnnnnnvonenrnnnnnnenrennnnnsnrensnrnnnrnnsnree 0 40 C Shipping Weight Am iia an ed Sas 2 lbs 13
7. ource IR remote control The IR signals are sent back to the source device when using an IR Blaster on the Sender Locking HDMI Port Connect a 3D display to this HDMI port Please see the Features section on page 3 for supported HDMI 1 3 features Power Indicator This LED will turn bright red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supply has been connected to an available wall outlet 5V DC Locking Power Connector Connect the included 5V DC locking power supply to this connector Only use the power supply shipped with this unit CONNECTING AND OPERATING THE EXTENDER FOR HDMI 3DTV How to Connect the Extender for HDMI 3DTV Position the Extender for HDMI 3DTV sender unit near the Hi Def source and the receiver unit next to the display Connect the Hi Def source to the sender with the provided locking HDMI cable Connect the HDTV display to the receiver unit with the supplied HDMI cable Connect the sender and receiver units together using a single user supplied CAT 5e or CAT 6 cables NOTE If terminating network cables in the field please adhere to the TIA EIA568B specification please see page 11 Connect a 5V DC locking power supplies to the sender unit Connect a 5V DC locking power supply to the receiver unit Do not overtighten the locking connectors Plug the two power supplies to an available wall outlet The LED on both the Sender and Recevier will turn b
8. right red indicating that both units are powered Power on the HDTV display and the Hi Def source A vibrant HDTV HD picture will be seen along with multichannel digital audio if the display supports audio NOTE If the source and display support 3D then the Extender for HDMI SDTV will pass through the 3D signal Wiring Diagram for the Extender for HDMI 3DTV Gefen CATS LINK CABLE TE T I g L R X HDMI CABLE EE HM Settop Box Receiver IR Blaster Sender HDMI Display GTB HDMI 3DTV DIP SWITCH CONFIGURATION DIP Swtich Location On the bottom of the Extender for HDMI 3DTV Receiver unit there are four 4 DIP switches The DIP switches allow advanced EDID management of the Extender for HDMI 3DTV which may be necessary when troubleshooting or using different brands of hardware The DIP switches allow control over the EDID and the HPD Hot Plug Detect status Receiver Unit bottom SEBA DIP Switch Bank 1 2 3 4 NOTE DIP switch 4 is not used Default settings for DIP switches DIP Switch Position 1 ON 2 OFF 3 OFF 4 NOT USED DIP SWITCH CONFIGURATION DIP 1 EDID Mode ON default External EDID Mode DDC and HPD are passed through Both the connection status and the full A V capabilities of the display The HPD status will also be detected by the source device OFF Internal EDID Mode e Local EDID is used instead of the EDID from the displ
Download Pdf Manuals
Related Search