operating instructions
Contents
1. Computer to locate the disk name pz Disk Format Tool Free 3111 Format Disk Total 3770 MB Free 3111 NB i i Format successfully 4 After formatting successfully you may click Exit www LumenCam com PROPER RECORDING ORIENTATION Please ensure that the recording on off and flashlight on off buttons are facing upwards during recording otherwise video files will not display correctly NOTICE Turn off the LumenCam if not in use Do not put the battery in fire or water Dispose of properly Do not use metal objects to connect the battery polarities Do not open the battery www LumenCam com SPECIFICATIONS Model No LumenCarr Imaging Sensor 1 4 inch Color CMOS Video Resolution 640 x 480 Viewing Angle 56 Video Format AVI Video File Size gt 15M Byte minute Viewing Resolution 640 x 480 VGA Storage Medium Built in Memory with up to 32GB Power Supply Li battery 3 7V 2000mAH Charging Time 4 hours Max Data transmission USB 2 0 Working Time 3 5 hours Min LED Light Power 1W LED Light Color Temperature gt 5500K Consumption Current Max 560mA Charging Current gt 800mA Dimensions W x D x H 191 x 56 x 56 mm Approx Weight 300g Operating Temperature 09 50 Operating Humidity 15 85 RH All the specifications are subject to minor c2. 1 Unscrew the handle of LumenCam and locate the USB port 2 Using the included USB cable connect LumenCam to any computer with a USB port 3 Your computer should automatically recognize the new hardware which you may browse by double clicking on the My Computer icon on your desktop and then navigating into the Mobile Disk directory If your computer is unable to playback desired video files please first install the video player software from the included CD Installing Lithium Battery 1 Unscrew the handle of LumenCam and locate the handle 2 Insert the Li battery into the handle with proper orientation Recharging Lithium Battery 1 Locate and remove the waterproofing plug at the base of LumenCam 2 Connect the power adapter to LumenCam and an 100 240V 50 60Hz power source The indicator will illuminate green when charging and turn off when fully charged www LumenCam com 2 NOTES 1 The indicator LED flashing red signifies critically low battery recharge immediately If power is completely exhausted the file you are recording will be saved automatically before shutting down 2 lf your memory is full pressing the recording on off button will cause the blue Indicator LED to stop and recording will not take place 3 When LumenCam is connected to your computer via USB cable it acts as a separate drive where files may be stored Date Time Reset If the date time of y
3. 4 1 uu am k LJ IVI E INSA IVI ILLUMINATING THE EVIDENCE rz WITH BUILT IN DIGITAL VIDEO RECORDER DVR FE RoHS www LumenCam com WELCOME Congratulations on your purchase of the LumenCam This high quality flashlight with Digital Video Recorder DVR will add years of safety to what you do as well as document evidence inventory events people or activities Please read the user manual carefully before using this product PACKING LIST D LumenCam x 1 2 USB Cable x 1 3 Software CD x 1 4 Power Adapter x 1 5 Safety Strap x 1 6 Lithium Battery x 1 The pictures are for reference only please refer to actual product STRUCTURE Indicator LED Recording on off Flashlight on off Bright LED e Low light LED Lens Low light LED Charge Indicator Power Jack www LumenCam com E OPERATION GUIDE Basic Operation 1 Press the flashlight on off button once for ultra bright setting suitable for illuminating distant objects Press again for wide angle setting suitable for lighting nearby objects Press a third time to turn off flashlight 2 Press the recording on off button to start recording and once again to stop A flashing blue working indicator LED light indicates recording in progress TIP When recording objects up close at night it is recommended to use the wide angle LED setting Video Output
4. hange without prior notice www LumenCam com 6 FCC Information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment I E EAR I A A AT Lem LJ IVI EIN NAIVI ILLUMINATING THE EVIDENCE www LumenCam com 349 n Vinewood St Escondido CA 92029 800 959 2899 EU Environmental Protection Waste electrical products should not be disposed of with household waste Please IN recycle where facilities exist K 22 Check with your local authority or retailer for recycling advice PAP
5. our video does not match the local date time please follow the these steps 1 Set the date time on your computer to match the local date time 2 Connect LumenCam to your computer via the USB cable provided 3 Double click the My Computer icon on your desktop and then navigate into the Mobile Disk directory This is the directory that the LumenCam SD card uses 4 Insert the CD provided into your computer s CD drive 5 Search your CD drive for a file named getsystemTime exe copy and paste this file into the Mobile Disk folder 6 Double click the file and wait for your system to automatically produce a i readme txt Di kFo AAT mae d resatan Y UU skf ormat exe j 5 Wes WDiskFormat Mic 1 7 You may now close all folders and disconnect the USB cable set up has been successfully completed a Formatting Memory It is highly recommended to use the software on the CD provided to format LumenCam built in memory Using the functions of a Windows PC system to format LumenCam will alter certain values causing video file storage time to become slower Follow the instructions below to format 1 Insert the CD provided into your computer s CD drive and search your CD drive for a file named UDiskFormat exe and double click on this file www LumenCam com 3 2 In the dialogue window enter the disk name that LumenCam is given when it is connected to your computer e g H G etc open My
Download Pdf Manuals
Related Search