Kadex - FingerTec
Contents
1. to con nect to the communication port of the terminal Select wires with label RS485 RS485 and GND and connect the other end of these wires to an RS232 485 data converter Connect the other end of the data con verter to a DB9 female connector Configure the device ID and baudrate of the terminal refer to the hardware user manual for details Step 5 Finalizing the installation 1 Check that all cable connections are done correctly 2 Attach the terminal to the corresponding back plates tighten the screws to secure the terminal on the wall 3 Switch on the power to the terminal 4 Start using the terminal Other Accessories Note All Accessories are offered at http accessory fingertec com Adaptec AdapTec AC The AdapTec ACis a 12VDC power supply inclusive of a 110 240VAC switching linear power The AdapTec supplies 12VDC power to the FingerTec terminal and door lock system as well as charges a 12VDC 7 0Ah backup battery simultaneously During an event of a power failure the back up battery automatically provides power to the terminal and maintains the door lock system The AdapTec AC also prevents a secured door from being opened if it has been tampered with Enclosures FingerTec offers enclosures to protect the terminals from being meddled with by unauthorized persons Door Lock Accessories FingerTec offers various door locks accessories to complement Fin gerTec door access product range Appendix Appen2. FING RIEC We Make Things Easy Installation Guide Kadex amp i Kadex Card Reader for Time Attendance amp Door Access Control System www fingertec com As ae Determine the Location and Positioning of the Installation e Avoid installing the terminals in locations with high moisture or condensation levels in the air e The recommended installation height of the terminal from the ground is 1 2 meter Step 2 Mounting of Terminals on A Wall REEE Back Plate q 4 feet 1 2 meter recommended e After determining the height of the terminal from the ground level and have made the relevant marks on the wall drill the screws into the wall to hang the back plate Refer to Appendix II for dimensions and measurements of instal lation Step 3 Wiring for Power Supply The power input ports for these models are located at the rear of the terminals There is no adapter plug supplied with the models instead you need to source for power cable red and black cables to connect the power from the terminal to the AdapTec USB Port Door Lock connector Refer to Appendix eejpeseseoooo TTT KIII tesos oeoooo 3rd party controller with 26 bits wiegand output 1 RS485 Single Connection RS232 RS485 Data Converter 3rd party controller with 26 bits wiegand RS232 RS485 f Data Converter power supply Connects to the master terminal and obtai
3. dix II Power Supply amp Door Lock System Wiring Diagrams Terminal Dimensions and Measurements gt Diagram1 Normally Close NC Door Lock Connectors WIRING PORT USAGE EM Lock NC Alarm System z T NO or NC Type Check mergency Breal 3 2 Glass Type NC in Advance Options Dry Contact independ Overwrite Switch Type NC ent power supply for door lock NO type door lock NO COM NC type door lock NC COM Power Contact using power from terminal to power on door lock NO type door lock NO GND NC type door lock NC GND DC12V 3A Power Supply Dry Contact independ ent power supply for door lock NO type door lock NO COM NC type door lock NC COM EM Lock NO Emergency Break Glass Type NO Power Contact using e power from terminal to Overwrite Switch power on door lock Type NO Type NO COM1 12V Release Button Door Sensor SEN GND Release button BUT GND DC12V 3A Power Supply Door Bell eran The terminal will trigger the alarm Front View of Kadex Front View of i Kadex output NO or NC for the follow ing situations Alarm device T NO or NC Dry contact Door forced open A door sen sor must first be installed Door open time out A door sen sor must first be installed e Terminal has been il
4. legally dis Door Sensor mantled Doorbell DC12V 3A Power Supply
5. ns 485B NC2 485A coM2 GND N02 2327 NCI 232R COM1 i GND NOt l WD1 BUT woo GND RJ45 1 RJ45 2 DC 12V 3A GND RJ45 3 Power Supply HOV RI45 4 Back of a Master Terminal Connection of i Kadex to Kadex Step 4 a Setting Up Data Communications Skip this step if you are using USB flash disk to transfer data The data communication ports are positioned at the rear of the terminals please refer to the diagrams shown on Step 3 to deter mine the wiring Plug the communication jacks TCP IP RS232 or RS485 to the corresponding ports TCP IP LAN Connection For TCP IP connection plug the special RJ45 jack into the TCP IP LAN Port of the terminal Connect the other end normal RJ45 jack to the local area network hub or a PC Configure the device ID IP address subnet mask and Gateway in the terminal refer to the hardware user manual for details RS232 Serial Port Connection Plug the communication jack that is provided in the package to connect to the communication port of the terminal Select wires with label RX TX and GND and connect the other end of these wires to a DB9 female connector Configure the device ID and baudrate of the terminal refer to the hardware user manual for details Use the normal RS232 cable to plug into the RS232 port of the termi nal RS485 Serial Port Connection Plug the communication jack that is provided in the package
Download Pdf Manuals
Related Search