Manual - Polywell Computers
Contents
1. 3 Installing extension interface card E Installing graphics card This motherboard provides one interface slot for PCIEx 16 graphics card When you install the PCIE graphics card you should note that throve of the golden finger must be exactly engaged into the interface slot In that process it is preferable that you be in grounded state and you should carefully take out the graphics card from the anti static bag Then align the graphics card to the PCIE interface slot and insert it After that tighten the screw on the metal baffle al Graphics Bracket a card Screw F ti ea i Motherboard gt f Po iA a 4 Setting motherboard s jump wire and inserts Note The user should note that all receptacles are marked with PIN1 The symbol indicates the ex factory default value of the motherboard f1 SATA1 SATA2 SATA3 SATA4 Serial ATA wire harness receptacle Serial ATA receptacle can offer a transmission speed of 300MB sec You can connect the Serial ATA devices to this receptacle 2 CPU_FANI SYS_FAN1 CPU fan s receptacle This receptacle can be used for connecting CPU system fan Its pins function are defined below The user shall make sure the fan is conforming 3 CLR_CMOS CMOS port The correct time system hardware and other information are saved in the CMOS memory of the motherboard The shutoff the computer s power supply won t cause the loss of this information for the CMOS is2. CLR_CMOS CMOS pin F_USB1 F_USB2 Frond end USB pin F_ AU DI O Pin for front end sound card A TX 24 P Power receptacle F_ PA NE L Front end control panel I D E 1 Wire harness receptacle for hard disk 5 Rear interfaces of motherboard 14 lll BIOS Setup 1 Main menu 16 2 Standard CMOS setup 18 3 Advanced BIOS setup 18 CPU Configuration 18 IDE Configuration 19 IO Chip Configure 20 PC Health Configuration 21 4 Power management 2P 5 BOOT setup 23 6 Security setup 25 ee 7 Chipset setup E s Exit D iV Installing software YP 1 Installing driver for motherboard Installing driver for main chip Installing driver for sound card Installing driver for on board network interface card Installing driver for video card HD AUDIO sound card setup 26 28 29 30 30 31 31 52 Chapter About the Product 1 1 Gratitude Thank you for purchasing ITX 945GC3B N330 Motherboard made by OEM Employing INTEL 945GC ICH7 and on board IN TEL A tom N330 CPU this product supports front end wire harness 1066MHz dual channel memory standards of DDR II 667 533 and USB2 0 and is built with on board HD AUIO sound card a 1 2 Accessories Your Mini ATOM N330 Motherboard consists of the following accessories If any of them is missing please contact your local distributor as soon as possible J 1 ITX 945GC3B N330 Motherboard One piece 2 User s Manual V1 0 for Mini ATOM N330 Motherboard One copy J 3 Warranty Card Q
3. Supports Director Sound and Sound Blaster Supports NPN and APM 1 2 Supports Win2000 XP Vista driver Supports Line in Line out and Mic in Supports front audio ports Power management 1 Supports APM and ACPT 2 Compatible with Green PC Extended interface One PCI Express x16 graphics card interface Chapter II Installing Hardware Warning The motherboard consists of a great number of ICs and other components These ICs are apt to be damaged by the static charge Therefore the user must make the following prepara tions before formal installation 1 Turn off the power of the computer It is preferable the power cord be unplugged 2 Take care not to contact the metal wires and theirs joints on the motherboard when handling it 3 Itis preferable that the anti static wrist strap be worn 4 Before the ICs are installed the components of the motherboard should be placed on the anti static mat or bag 5 When you remove the plug on the ATX power sup ply of the motherboard make sure the switch of the power supply is in OFF state Installing the motherboard onto the computer case For most of the computer cases the multiple fixing holes left on their bottoms can be used for securing the motherboard and no short circuit can occur therefrom During your operation take care not to allow the screws to contact any circuit or part on PCB When circuits on the surface of the motherboard get close to the fi
4. control program saved in the Flash Memory Bridging the motherboard and the operating system BIOS is used for managing the setup of the related parameters between them When the computer is activated the system is first controlled by the BIOS program First a self detection called POST is per formed to check all hard devices and confirm the parameters of the synchronous hardware Once all detections are completed BIOS will hand over the controlling to the operating system OS The correct setup of BIOS plays a key role in stably running the system and optimizing its performance The CMOS Setup will save the set parameters in the built in CMOS SRAM on the motherboard When the power is shut off the lithium battery on the motherboard will supply power CMOS SRAM continuously The BIOS setup program will allow you to configure the following items i HD drive floppy drive and peripheral devices f2 Video display type and display items Bs Password protection f4 Power management characteristics A State of BIOS Setup When the computer is started up BIOS will run the self detection Post program This program includes series of diagnosis fixed in BIOS When this program is executed the following information will appear if any error is found Press F1 to Run Setup Press F 2 to Load default values and continue To enter BIOS you can press F1 to load the default values and enter the system you can press F2 After the self detection
5. is enabled you will be required to enter the password each time before the system goes to the set program of BIOS The user can set this item through the Security Option in advanced BIOS properties If the item Security Option is set as System the password will be required to be entered before the system guides and goes to the set program of BIOS If set as Setup the password will be required to be entered only before the system goes to the set program of BIOS To delete the password press lt Enter gt in the popped up window that requires to enter the password Then information for confirmation will appear on the screen to allow you decide whether the password is disabled Once the password is disabled you won t have to enter the password and can enter the setup program directly when the system is restarted Boot Sector Virus Protection This item is used for setting the alarm function in the case of virus attack in IDE disk sector If this item is set as Enable and some program wants to write informa tion in the sector BIOS will display alarm information on the screen and buzz ai 3 7 Chipset setup e Ari biip Coal ipri iam Figure 3 10 NorthBridge Configuration To set the north bridge chip J SouthBridge Configuration To set the south bridge chip E RX780 Configuration E USB Configuration To set the USB devices il 3 7 1 USB Configuration LES Part ipen E Barbs Figure 3 11 26 J Legac
6. process is completed you can press DEL to enter the BIOS interface if no error is found If the indicative information disap pears before you can act you can shut off the computer and turn on it again or you can press the key RESET on the machine case To restart your computer you can also simultaneously press lt Ctrl gt lt Alt gt lt Delete gt B Keys and functions Save the set values and exit the CMOS SETUP state C Auxiliary information Main interface When the system enters the main interface of Setup the major selected contents will be displayed at the lower part of the interface with the change of the options Set interface When you set the value for each column you can view the preset value of the column and the values that can be set if you press F1 for example the BIOS default values or CMOS Setup values To exit the interface for auxiliary information press ESC eee 3 1 Main menu When the system enters the interface of CMOS Setup menu you can see the main menu on the upper part of the screen as shown in Figure 3 1 In this main menu you can use the left and right direction keys to select the setup items Once the item is selected the lower part of the computer screen will show the details of setting Figure 3 1 The selections and their contents may be different from the actual selections so they are only used for reference 1 Main standard CMOS setup This item is used f
7. system can support f ACPI APIC support This item allows you decide whether acpi apic form to rsdt indication list Options are disabled and enabled Power Management APM This item is used for enabling or disabling the APM advanced power management function The default value is Enabled When enabled is selected BIOS can set the system as power saving mode in accordance with the later setup even if no operating system provides any support f Power Button Mode The defaulted value ON OFF indicates that the system will turn ATX switch into a common shutoff button if the ATX switch is in the pressed down state for less than four seconds If Suspend is selected it means the system will enter the sleeping mode if the ATX switch is in the pressed down state for less than four seconds Whatever option is selected the system will be shut off if the ATX switch is in the pressed down state for over four seconds Fi Restore on AC Power Loss This item is used for setting what state the system should be in when the AC power is restored after power interruption The options and their definitions are as follows Power Off To allow the system to be in shutoff state To allow the system to be started automatically To allow the system to keep the pre power off state Power On by PCI Card To start the PCI device J Wake Up by PCIE To wake up PCIE f RTC Resume If Enabled is selected you can start the system through rea
8. via BIOS E IDE Detect time out Sec This item is used for setting the time the system should wait for automatic detection of ATA ATAPI device The options are 0 5 10 15 20 25 30 and 35 E 3 3 3 IO Chipset Configure TU UL LITT Serial Port Address Figure 3 5 f Serial Port 1 Address To set the built in serial port 1 COM1 port The options are Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 and Auto The default value is 3F8 IRQ4 Serial Port 1 Mode If this mode is set as Normal 1 it will be used for the mouse and modem If IR device is available IrDA it is recommended this item be set as IrDA ADKIR Parallel Port Address To set the address for the parallel port a Parallel Port Mode To select the transmission mode for the parallel port ECP EPP Normal The default mode is Normal J Parallel Port IRQ To set the parallel port IRQ It is recommended this item be set as 7 20 f 3 3 4 PC Health Configuration WU Health Fusrt ina lEsab led Figure 3 6 f H W Health Function Through this item you can view the state of the system hardware You can view the speed of the CPU fan temperature of CPU and other values CPU Fan Speed Control To set the CPU fan s mode Options include Manual Mode and thermal Cruise Mode 3 4 Power power management E waal BOF Caaf ieee at ban Figure 3 7 f ACPI Version Features To set the power type the
9. A Card One for each g 4 Data cable for hard disk 80 Pin One piece Be 5 SATA hard disk cable One piece 6 Driver s disk One piece EE 3 Picture of the motherboard Note The above figure is the picture of ITX 94GC3B motherboard This picture is only used for reference and the physical object shall prevail 4 Features f System processor 1 Built with on board INTEL Atom N330 CPU System memory 1 Supports one 240 Pin DDR II 667 533 memory 2 Supports 2GB of memory at maximum 3 Supports single channel memory mode System BIOS 1 Supports PNP APM and ATAPI 2 Supports ACPI and DMI 3 Automatic detection and supporting hard disk the LBA mode of which is over 160G 4 Easy for end users to upgrading the motherboard with BIOS Interface of peripheral equipment 1 One quick IDE port supporting DMA33 66 100 hard disk CD ROM ZIP LS120 and other drivers 2 Integrated with PCIE kilo mega network interface card RTL8111C 3 One 16650 compatible UART serial interface 4 Supports 4 SATA II hard disk interface 5 6 high speed transmission ports max 480Mb s which sup port USB2 0 compatible with USB1 1 6 One PS 2 keyboard connector 7 One PS 2 mouse connector 8 One CMOS pin 9 One receptacle for system fan 10 One interface for case panel compatible with HDD LED and Speaker 11 On board HD AUDIO sound card 1 2 3 4 5 6 Integrating HD AUDIO sound effect controller
10. OEM ITX 945GC3B N330 Motherboard User s Manual V1 0 The ownership of all parts of this product including the accessories and software is enjoyed by OEM production Electronics Co Ltd Imitating replicating abstracting or transferring of the product is not permitted without the consent of OEM The product specifications and other in formation provided in this Manual are only used for refer ence and shall be subject to change without prior notice The names mentioned in this Manual are only used for purpose of identification Some of them may be the trade marks of other companies or their copyrights are owned by those companies We will be appreciate if we are informed about any error or ambiguous description in whichever part of this Manual including that of the hardware and software Service hot line US 800 664 8917 Email info OEMproduction com All rights reserved i About the product 1 Gratitude 1 2 Accessories 1 3 Picture of the motherboard 2 4 Features 3 System processor System memory System BIOS Interface of peripheral equipment Power management Expansion slot Il Installing hardware 1 Layout of motherboard 6 2 Installing memory card ii 3 Installing extension interface card 8 Installing PCIE video card 4 Setting motherboard s jump wire and inserts 9 SATA 1 SATA2 SATA3 SATA4 Serial ATA wire harness receptacle CPU_FAN1 SYS_FAN1 CPU fan s receptacle system fan s receptacle
11. ing one end of the wire harness of the floppy drive The other end of the wire harness will be connected to the floppy drive Normally Pin 1 of the wire harness is marked with red color Please insert into corresponding Pin 1 of this receptacle Hl 8 I D E 1 Wire harness receptacle for hard disk One IDE wire harness receptacle is set on this motherboard Each receptacle can be connected to one IDE wire harness and each wire harness can be connected to two IDE devices Insert the blue plug of the wire harness into the IDE1 receptacle on the mother board and insert the other end into the IDE device Normally Pin 1 of the wire harness is marked with red color Please insert into corresponding Pin 1 of this receptacle 40 39 Z l 5 Rear interfaces of motherboard HF iE 4 r E Bi Receptacle for PS 2 keyboard and PS 2 mouse This motherboard provides two receptacles respectively for PS 2 keyboard and PS 2 mouse You can connect the PS 2 devices through these receptacles J 2 COM interface VGA interface f 3 LPT interface J 4 USB interface g 5 USB interface RJ45 network card interface g 6 Audio interface Chapter Ill BIOS Setup Note The descriptions relating to BIOS in this Manual can only be used for reference as the BIOS version of the motherboard is upgraded continuously OEM provides no guarantee that the contents in this Manual be consistent with the information you acquire BIOS is a basic I O
12. l time clock Pe 3 5 Boot setup Figure 3 8 i Quick Boot If this item is set as Enabled the system can be started within five seconds and some detection items will be ignored The options are Disabled and Enabled f Quiet Boot Start the system quietly J Add On ROM Display Mode Force BIOS This item allows you to set the display mode of the device s firmware program The options are Force BIOS and Keep Current Bootup Num Lock To set the state of Num Lock Options are OFF and ON In other words this item can be used for setting the state of Num Lock for the time the system has been started It can be set on the basis of the needs of the user and poses no influence on the performance of the computer PS2 Mouse Support To set whether the system can support PS2 mouse The options are Auto and Disable The default value is Auto Wait for F1 if any Error The system waits the user to press F1 if any error occurs from the computer The options are Disable and Enable Normally it is set as Enable Then if the computer has any error a line of English words will appear on the screen reminding the user of pressing F1 to enter CMOS for setup If it is set as Disable that line of English words won t appear However if the words wait appear during the start up process and you press Del the system can also enter CMOS for setup Hit Del Message Display Information is displayed when the co
13. mputer is started suggesting the user can press Del to enter the state for CMOS setup The options are Disable and Enable Normally Enable is selected After Enable is selected the information on how to enter the state for CMOS setup will be displayed at the time the computer is started If Disable is selected such information won t be displayed However if you press Del when the character Wait appears at the time the com puter is started the system can also enter the state for CMOS setup Interrupt 19 Capture Disable If you use some PCI extension cards with built in firmware program like SCSI extension card and you want to start the system through Interrupt 19 you can set this item as Enabled The options are Disabled and Enabled Boot Device Priority To enable the priority order for setup Hard Disk Drives To enable the order setup for hard disk Removable Drives To enable the order setup for removable memory devices CD DVD Drives To enable the order setup for CD DVD memory devices 3 6 Security Setup P UTILITY Change Supervisor Password Figure 3 9 If this function is selected the following information will appear Enter New Password hhhhhh Then enter the password with not more than eight characters and press lt Enter gt BIOS will require entering the password again Once you enter it again BIOS will save the set password Once the password item
14. or setting the date time specifications of hard disk and floppy disk and type of monitor ai 2 Advanced advanced BIOS setup This item is used for setting the advanced functions provided by BIOS such as the virus alarm and priority order of disks for startup process a 3 Power ACPI power management This item is used for setting ACPI advanced configuration and power management J 4 Boot startup configuration characteristics J 5 Security setting the administrator user password J 6 Chipset setting the performance of the chips This item is used for setting the voltage frequency and other items of Northbridge Southbridge USB and other devices 7 Exit option of exit This item includes load optimal defaults load failsafe defaults value discard changes discard changes and exit EE 3 2 Main standard CMOS setup Figure 3 2 i 1 System time hh mm ss To set the time for the computer with the format of hour minute second i 2 System date mm dd yy To set the date for the computer with the format of week month day year GE 3 3 Advanced Advanced BIOS setup E 3 3 1 CPU Configuration Fis CAG Gales Laii DE j ants ht Figure3 3 3 3 2 IDE Configuration P UTILITY Caf igure SATA as Figure 3 4 f Hard disk write protect This item is used for turning on or off the function of write protect This function can only be activated when the device is accessed
15. ou enter OK and press Enter the system will exit from the BIOS setup program If press Cancel return to the main menu Discard changes If you enter OK and press Enter the system will discard the changes If press Cancel or Esc return to the main menu Chapter IV Installing Software E 4 1 Installing driver for motherboard After you complete the installation of the operating system you should then install the driver for the motherboard To do that put the driver disk into the CD ROM The interface as shown in Figure 4 1 will appear Figure 4 1 Click Install Driver the interface as shown in Figure 4 2 will appear Figure 4 2 f 4 1 1 Installing driver for main chip After you click Install behind the Intel Main Chip in the inter face of Figure 4 2 a dialog box as shown in Figure 4 3 will be popped up Then you can click Next and wait till the driver is installed completely intel i Ghee fewer Sa herarr Intel Chipset Device Software Wakana bo tie Sarbum Pisce cit This HUD Diners Ral eed thes rel Cheapest e Saas ono thee one E E throngs receded Pt sou a all progr Conran Figure 4 3 4 1 2 Installing driver for sound card After you click Install behind the Realtek High Definition Audio Driver in the interface of Figure 4 2 a dialog box as shown in Figure 4 4 will be popped up Then you can click Next and wait till the driver is installed completel
16. powered by the battery on the motherboard Its settings are seen below 1 a Clear CMOS eoa Ezk e FE nE E TE ali i i eu pu HEHH 1 2 a Hi j HRE aim ea e r E f 4 F_USB1 F_USB2 frond end USB port In case the USB ports on the rear panel of the machine case are insufficient the user can use the extension USB ports provided by this motherboard These ports support USB 2 0 devices The definitions of the ports are described below Pin Defnition Pin Definition Pfs Ts Ta os m Felu i o e e Ce nouses Emoy 7 5 F_ AU DI O Port for front end sound card These sound card ports allow you to connect to the wire harness of the sound card After connection you can easily control the audio output microphone through the front panel of the host Note Don t connect the wire to Pin 4 The definitions of the ports are described below pra z Pin Definition Pin Ground 4 tote a 7 Ground 8 Empty 9 Output of left channel 6 ATX 24 P Power receptacle This receptacle is used for connecting the 24 pin outlet of the power supply The definitions of the ports are described below when power supply with 20 pin outlet is used please make sure the numbers are matched correctly 16 D aU 11 od OVUOOOVOOOO MNOOOOUOOU0O 10 l i 7 F_ PANE L Front end control panel Wire harness receptacle for floppy drive This receptacle is used for connect
17. t the corre sponding output ETA TAA TEHE DARHA ERM HH FRI EEUE Oe it SAATE FRB sree Figure 4 15
18. talled you can click the Audio Manager at the lower right corner The initial interface will be popped up as shown in Figure 4 10 and 4 11 Figure 4 10 oo ae o ine 2 dat Arae d Figure 4 11 2 Click the right upper part of the control interface Advanced Setup for Device the interface shown in Figure 4 12 will be popped up Then select separate all input jacks as independent input devices hs a ee Pb EI TE ba C ee Figure 4 12 3 Click OK the control interface will turn to one shown in Figure 4 13 ia E aa mon ee ee ee ae i I h F i Bi bihe prema Jart i Er ETIR 5 ae BATE il Figure 4 13 4 If a mic is used please select the corresponding front or rear mode and set the device as default In the above interface you can adjust the volume for recording and the playing volume for the mic 5 If you need to set the output of multi channel you should right click the mouse at the corresponding output interface A dialog box will be popped up as shown in Figure 4 14 T E Babri mni HY z i nme ira m ope pajni ran p er prai fiaj Fa me r hamp LES rr EJ ph ithil Eidi HEEE 7 umac BaT 5 a P kat oe i r Fra 7 Ga ni Ona et lt Fie lt pap GE Bhd re 4 ks it REALTEK d Figure 4 14 6 Select Redistribution of Connectors Then an interface will be popped up as shown in Figure 4 15 After that se
19. xing holes you can use the plastic sheet to sepa rate the screws from the board surface so as to avoid damage or failure of the motherboard 1 Layout of motherboard Tee 2 Installing memory card Please install the memory card in accordance with the following procedures 1 Remove the white tenon at the two ends of the interface slot for the memory card 2 Align the golden finger of the memory card to the throve of the interface slot and pay attention the concave hole of golden finger should be aligned to the convex point of the slot Remove outward the white tenon at 4 the two ends of the interface slot for module of the memory card 3 Finally insert the memory card into the interface slot gentlely If no error occurs at the moment insert the card forward in the slot till the white buckle is automatically engaged in the concave hole at the two sides of the memory card Note In order to avoid damages to the motherboard or the components the user must make sure the power supply to the computer is turned off before the memory card or other system component is installed or removed As the throve is set at the golden finger of the DDR DIMM memory card the memory card can only be inserted into the slot with one direction During installation the user only needs to align the golden finger and the dual channel throve of the interface slot and insert it gentlely To avoid damage never apply excessive force in that process
20. y Peed ri gs Le et i ees en es ead at le bra ai Sah san ls Paa gh Ee retin dee aa Fie Dic Er el Frat eget Jeera Tma arume LELE i up Figure 4 4 D 4 1 3 Installing driver for on board network interface card After you click Install behind the Realtek 10 100 1000 Network Interface Card Driver in the interface of Figure 4 2 a dialog box as shown in Figure 4 5 will be popped up Then you can click Next and wait till the driver is installed completely LE LLI G la Oh rH Fo HE ee eee Pe aire oe oe i aa EER LAE Cote T aT i m ie i Ibr seer anha e L H L Cil LTE l drer FPO HE Carr m n eee 2 le rmm star Epi Figure 4 5 4 1 4 Installing driver for video card To install the driver for the video card you can click Install behind nVIDIA Integrated Video Card Driver in the interface of Figure 4 2 complete the installation by following the indications in the popped up dialog boxes and then re start the computer ME 4 2 HD AUDIO sound card setup In the system of Windows XP SP2 1 The control panel of the sound card will appear after the driver is installed as shown in Figure 4 7 Figure 4 7 2 After the initial installation of the driver the default of mic is in mute state You need to turn it on manually as shown in Figure 4 8 and 4 9 Figure 4 8 Figure 4 9 In the system of Windows Vista 1 After the driver for the sound card is s
21. y USB Support This item is used for enabling or disabling the supports for USB devices If the default value Auto is selected the system will auto matically check whether USB device is available in its startup process If USB device is available USB controller will be activated If not it won t be activated If you set this item as Disabled the USB con troller inside the system will be in OFF state regardless of whether USB device is available The options are Disabled Enabled and Auto E USB2 0 Controller Mode This item is used for setting the transmission rate for USB2 0 devices The modes include HiSpeed 480Mbps and Full Speed 12Mbps The setup options are HiSpeed and FullSpeed 3 8 Exit LS SEF iLi Sey Daaa aml Exit Figure 3 12 f Exit Options The exit options include load optimal defaults load failsafe defaults value discard changes discard changes and exit Load failsafe defaults optimal defaults These two items can allow the user to restore all BIOS options to the failsafe defaults and optimal defaults The optimal defaults are set to optimize the performance of the motherboard The failsafe defaults are conservative values for the system If you enter OK and press Enter all set values will be saved to CMOS SRAM and the system will exit from the BIOS setup program If you don t want to save you can press Cancel or Esc to return to the main menu Discard changes and exit If y
Download Pdf Manuals
Related Search