PHEV Add-on System User Manual
Contents
1. 5 8 5 Check Toyota battery orange high voltage service plug to ensure it is plug in correctly locked and secured 6 Check splice wires to make sure the connectivity is not compromised and the wire is correct Splice may occasionally cut off the original wire 7 Use scan tool to reset Error Code or disconnect the 12V battery and wait for 15 minutes to reset the Error Code 8 Re check your vehicle and confirm it is operational 9 Turn on Enginer PHEV circuit breaker while keeping HV output wires disconnected 10 Start your vehicle 11 Check if Enginer PHEV switch panel is only green light on when the switch is at ON position Also check the light on the converter output panel in the battery box 12 If the green light is not on use a meter to check if the Ignition 12V signal is 12V on the PHEV switch panel Also check the phone cable connector on the converter side to make sure pin 5 6 have 12V signal 13 Check OEM battery high voltage Pay attention to the polarity of the wire 14 Check PHEV converter output high voltage Pay attention to the polarity The voltage should be 5 10V higher than the OEM battery voltage 15 Turn off the car before connecting the converter high voltage to the OEM battery 16 Turn on the car in Park check PHEV battery voltage which should drop 1 5V when charging the OEM battery 17 If the PHEV voltage drops more than 5 volts check individual cell voltages to locate weak cell s that is are signific2. No manual shut off is necessary It takes about 5 hours to charge up from drained Lithium lon batteries should often be charged even if they have not been used up If the indicator is not on or flashing red check the charger fuse or contact your installer or Enginer for advice Lithium battery needs to be charged above freezing temperature 32F 0C If ambient temperature is under freezing point heating device is needed to avoid permanent battery damage With a working PHEV System the Prius Energy Monitor should stay in seven 7 green bars most of the time If it often shows eight 8 green bars or only six 6 or fewer blue bars please contact your installer or Enginer for advice It is recommended to have access to a scan tool such as Scangauge and a wattage monitor like Kill A Watt device to monitor and optimize your driving experience with this PHEV System Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius Product Overview The Enginer PHEV Add on System is a rechargeable battery set that supplements Prius OEM battery The System supplies stored electricity which was previously charged from an AC wall socket providing 40 miles of electrically assisted driving distance per charge sufficient for most daily commutes It is safe reliable and user environment friendly What is Included in this Product 4KWH Lithium lon batteries BMS monitoring and balancing batteries
3. Enginer PHEV Add on System User Manual for 1997 2003 Prius Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius Driving Techniques for Maximizing Enginer PHEV Mileage 1 Maintain as steady speed as possible at all times 2 When attaining the speed you desire on the road feather the accelerator or lifting your foot off entirely then very lightly easing back in to maintain a steady speed of under 34 miles or 70km per hour That motion activates your Prius EV feature to consume battery power only Tests in this driving style on Enginer Prius PHEV have shown way better than 100MPG or 100KM 2 83L with the best factory field test outcome of 160MPG or 100KM 1 7L for accumulated test drive distance of 165KM Attention 1 Please read and follow the instructions before and during installation 2 Please never connect wires improperly and do carefully check them for at least 3 times before switching the power on 3 New system batteries should be re charged to full and well balanced before driving 4 Please monitor individual cell voltages and balance them regularly 5 Please make sure the voltage as labeled on the charger matches that from your household electricity source 6 To extend battery life the System should be recharged to full each time especially before the System is to be left unused for over 10 days 7 To avoid possible battery failure please turn of
4. Even if it appears to function properly your actions may cause it to self destruct with collateral damage to surrounding properties other than your vehicle By utilizing these ideas and instructions in an attempt to enhance national security reduce gasoline consumption vehicle emissions your carbon footprint or smog you do so at your own risk amp peril Contacts US Distributor Enginer Inc Michigan USA Web www Enginer us Email CS Enginer us Toll Free 877 886 8897 Address P O Box 3 Troy MI 48099 USA Manufactured By Enginer Inc Shanghai Address 111 7580 Humin Road Shanghai China 201102 Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius Preparing and Assembling Enginer PHEV Add on System Please carefully read and understand these instructions before opening the product container Installation and Use 1 Prepare a flat area of at least 7x7 feet on the ground near the end of your Prius and cover the floor with a 5x5 feet soft and flat cloth or cardboard 2 The equipment is heavy and should be removed and carried by at least two adults As industry standard it is suggested that the System should be handled by a lifting machine Knock open the wooden box if there is one and then open the cardboard box in side 4 Take out accessories and place them in a place not impeding your later installation Take out the foam plastic cover from the c
5. One DC DC converter mounted back left with a pair of red and black power inlet cores ending with an Anderson plug to battery packs It also contains a pair of power outlet red and black and a 6 pin cable m One power charger mounted on right back with a black power inlet cable on right hand side and a pair of outlet cores red and black on left linking an Anderson plug m BMS mounted above the power charger the side close to your body m Two ventilation fans attached on left top of the converter m One circuit breaker mounted on a side of the charger m One fire extinguisher fixed in the middle of the System and in between of the 2 battery packs Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius Right Pack Batteries Figure 1 Component Layout 7 Wiring Check Make sure circuit breaker is in the OFF position BMS interfaces off Charger and converter connections are appropriate solid and firm Black cores from batteries and to circuit breaker are connected correctly and firmly as shown below Circuit Breaker Figure 2 Connection of batteries 4KWH 8 Wiring Connect the Anderson plug labeled R to the R Right battery pack and L to the L Left pack Insert the R battery 9 pins white plug into the R connector on BMS and the L one to L connector Plug the 8 pin wire into BMS F
6. and unplug the orange OEM stock battery service plug Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius 3 Remove auxiliary battery negative terminal 4 Remove back seat and gain access to the OEM stock battery output terminals Reference HV 4 HYBRID VEHICLE CONTROL HV BATTERY for 2000 2003 Prius A Pull up the seat cushion pad front edge toward back B Remove back cushion screws and pull it up C Remove battery carrier catch bracket to access to power cable terminal The upper terminal is positive the lower is negative 7 8 81 70 in Ibf 5 Hog Ring Seat Cushion Cover 7 Hog Ring Seat Cushion Lock Hook EE Nm kgf cm ft Ibf Specified torque Non reusable part Seat Cushion Pad Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius 18 185 13 Bracket LH Battery Bracket Gs J iod amp Alf E 8 0 80 71 in Ibif 5 0 50 44 into Battery Carrier Catch Bracket Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius 5 Connect the System power cable to positive and negative terminals of the stock battery output power cable 6 Install on off switch panel A Take off the blank panel on the left hand side of your meter board B Loosen the switc
7. antly lower than the peer 18 Charging batteries 19 Wait overnight for the cells to be charged and balanced Final Stage Mounting Your Enginer PHEV Add on System A Mark eight mounting holes according to size and dimension of the System s mounting brackets B Drill two 13mm holes on the middle left of trunk floor plate all the way through the frame and three 13mm holes through the sheet metal C Put the rubber blankets under the brackets the long one for left bracket the short one for the end of right bracket D Tighten five mounting screws with washer and spring ring E Remove implements on the left side of trunk and put the vent pipe for circulating air inside PHEV F Tighten buckles on two sides of the enclosure box to mount the entire equipment Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius Remove this plastic tool hax Once all the above steps are completed and no defect occurs so tighten two screws on both sides of the steel lid you are now safe to drive your Enginer Plug in Hybrid Electric Vehicle Please dial Enginer Assistance Hotline at 877 886 8897 if you encounter difficulty or risk during and after installation Enginer appreciates your efforts to save our environment and wishes you safe and enjoyable driving with your new PHEV Enginer Inc 12 January 2011 User Manual for 1997 2003 Prius Enginer Plug in Hybrid Electric Vehi
8. ardboard box and pull out the steel box this requires at least two people with both hands carefully and steadily move out the entire steel box and place it gently on the floor Do not tilt or turn over the equipment 5 The equipment weights about 180 lbs Enginer strongly suggests you use professional lifting equipment or operators that are strong enough to lift this much weight Move the equipment slowly and carefully to avoid physical injury or equipment damage 6 After popping up the cover firmly and checking that it is safe with no risk of dropping down gently take out all insulating foam and check inside component and accessory bags against the following list m ECU signal wires green brown and white m One switch panel with On Off switch red and green LED lights m 6 pin phone wire m Converter high voltage core red and black core with blue bullet connectors m Power core for charger input m 2 sets of equipment mounting screws size M8 m One charger input bumper socket m One double sized spanner m One thread for converter and charger m 4pcs plastic clamps for connecting ECU signal wires to Prius m Two black rubber blankets the longer one for left hand side shorter one for the right hand side m One 50cm long vent pipe for left hand size corner ventilation fan m 1 1 mounting hole positions template m Steel box and cover 833 x 505 5 x 152mm m Batteries 4KWH in 2 packs Please make sure batteries match your order m
9. ciency or reduce gasoline consumption The PHEV switch should be in the ON position most of the time unless the PHEV red light is ON indicating low PHEV battery level or unless you wish to preserve the PHEV energy for later use When your vehicle and Enginer PHEV switch are both on the green indicator should also be on meaning the System is operational If the red light is on as well it means PHEV battery low or System error If the red light stays on all the time please contact your installer or Enginer customer service via Contact Us page on www Enginer us If your vehicle and PHEV switch are both on but green light is off please check the System circuit breaker by pressing it off and on again to make sure it is engaged If problem persists please seek support from Enginer or your installer Enginer Battery Management System BMS stores diagnostics information on an SD card inside and displays instant performance data on the dash LCD monitor Please refer to BMS User Manual for details and when making inquiry provide Enginer or your installer with the SD card data To charge the System it is recommended to use a Gauge 14 extension cord 15A and plug it into a standard 120VAC 220VAC power outlet with a 20A circuit breaker Its average current is 10A 120VAC or 5A 220VAC Once it is plugged in the external dual color LED indicator should turn solid red It turns green when batteries are fully charged and the charger stops automatically
10. cle Add on System uid AI ONS AZ uomnubBi Les ECH SJ S E 9280 euoug azrH 28ds JapyeAu OF SYED Jano EL i8 ar ADEE OPE oF ref Oct Brit AOL L JOABSP T eag VOOL LS Sa eot E MODOP MODDE Jape AUD OO OO ARP Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius NOTE Enginer Inc 12 January 2011
11. f the BMS if the System is not to be used for over 10 days 8 The circuit breaker on the right hand side of the enclosure box will be switched off automatically whenever current exceeds the pre set limit 125A In the event that this breaker switches off you will need to manually press it back on before use You are suggested to report such errors to Enginer or your installer if this keeps happening 9 Please switch the equipment off immediately if any damage or defect occurs 10 Please do not disassemble the System if it is working properly and if you are not a qualified professional 11 Charger and converter fuses can be replaced if blown A Charger fuse Fuse block of the charger is inserted in the AC plug You can use a flat screw driver to pivot the block in the middle edge above the fuse sign and pull it outward 4 Seed LIN SY E LIII B A L LALULLLZZZI Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius B Converter fuse The fuse block is connected to the high voltage core You can open the block and replace the fuse User Guide Enginer Add on System is designed for PHEV blended mode operation and therefore EV mode switch is not required although it is an option This PHEV technology minimizes possible impacts on your to preserve your original warranty The primary goal of the System is to improve fuel effi
12. h bolt place it on through the panel hole and tighten it on the panel Before replace panel After replace panel eS EJ 1 E 7 Hook up ECU Ignition Ready signal to on off switch panel Reference DI 20 Terminals of ECM for 2000 2003 Prius CON2 H12 2 Grey Ignition Ready Connect to the Green wire of PHEV switch panel GND1 H14 31 White Black Ground Connect to the Brown wire of PHEV switch panel Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius m 5 MALI 7 E c te MM Hum Ee Li l z A PEE s 1 Cowl Side Trim Front Door Souf Plate 8 Hook up 6 Pin On Off switch panel cable to your Enginer battery box 9 Drill a hole and mount Bumper AC Outlet 10 Recover back seat and trunk panels Reposition the Service Plug Grip firmly before electric power resumes Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius Your Enginer PHEV Add on System installation is now complete Please test the equipment in the following steps 1 Turn the Enginer circuit breaker off 2 Disconnect the converter high voltage output to the OEM battery red and black wires with blue bullet connectors 3 Start your vehicle 4 f the vehicle does not start with the Check Engine light on do step
13. irmly link the high voltage cores red and black cores with blue bullet connectors with the converter output connectors Plug in the 6 pin phone wire to the converter 9 System assembly is completed and ready to be installed into your vehicle 10 Bumper outlet for charger connection Black wire Live line L White wire Null Line N Green wire Ground Line E Take the charger core through the back panel and reach to bumper outlet You need to get your hand in from under the car and tighten the silver ring of bumper plug Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius 11 Install the Charger LED into the tail light this LED shows charger operation Red LED Charging at about 15A Green LED Fully charged 12 PHEV switch panel operation ON Turn on PHEV DC DC Converter LED Green On Red Low Battery OFF Turn off PHEV DC DC Converter LED Off Connecting Enginer PHEV Add on System to your Prius Installation Time 4 hours by professionals Before installation please login to Toyota Technical Website techinfo toyota com for Reference Instructions 15 for two day usage as of June 2009 Preparation tools required Screw shell M6 M14 Crosshead screwdriver Electric drill Installation Procedure 1 Stop your Prius engine completely by taking away your car key 2 Remove trunk interior cover on the back of the back seat to gain access to
14. to avoid individual cells over charge discharge extending battery life 110VAC 48VDC 15A high power charger oKW DC DC converter and controller Fire extinguisher will be activated once the inside temperature exceeds 221F First of all please remove the cover and pull out the blue isolation inserter BO Crne Automatic DC circuit breaker to disconnect high voltage equipment operation in the event of a high current fault Steel enclosure O How the System Works 110VAC USA household electricity gt Enginer PHEV Add on System gt Prius OEM stock battery gt Jointly drive Prius electric motor Capacity Average Gas Mileage EV Mixed Range Charge time Batteries Lithiumon lon Use 110V AC source EN or other AC source matching PHEV charger only Enginer Inc 12 January 2011 Enginer Plug in Hybrid Electric Vehicle Add on System User Manual for 1997 2003 Prius Warranty Two year limited parts warranty applies If equipment defect occurs in normal use conditions Enginer shall repair the equipment or change the defective component in this System only Use this information at your own risk Other than as specified above there is no additional warranty expressed nor implied and Enginer shall not be liable for any of your past present nor future actions Even if you perform these modifications to the latter you could still damage any number of components in your vehicle causing it to no longer functional
Download Pdf Manuals
Related Search