BTH-200 Bluetooth® Headphone User Manual
Contents
1. sizes One 1 USB charging cable Optional One 1 User manual CHARGING YOUR HEADPHONE Warning Use the supplied charger only One must fully charge the battery before first use Generally the process takes about two hours 1 Connect the USB cable to BTH 200 and USB car charger the computer or other power sources 2 While charging the status indicator light turns red constantly It will be turned off when charging is complete 3 Detach the USB cable from BTH 200 and USB car charger the computer or other power sources Warning For your safety if you need to answer the headphone please disconnect it from the power source LOW BATTERY The headphone needs to be recharged when it flashes red POWER ON OFF Power on Long press the multifunction button for about 3 4 seconds till the blue status indicator light is turned on Power off Long press the multifunction button and volume up for about 3 4 seconds till the red status indicator light is turned on Regulatory Notices FCC REQUIREMENTS PART 15 Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection agains2. the brand and models Please refer to the manuals of those devices for details 1 Make sure your BTH 200 is turned off 2 Turn on BTH 200 In standby mode Press and hold the multifunction button 5 seconds till the red blue status indicator lights flash alternatively 3 Follow the instruction of the phone manual to activate the Bluetooth function and search for Bluetooth devices When searching is done select BTH 200 voice device Enter the preset passkey 0000 and paring will be successful At this point the headphone enters the Stand by mode If the handset support simplified paring capability then there is no need to enter the passkey If paring fails then repeat steps 1 through 5 of the above procedure 6 Confirm to link to the BTH 200 and the headphone will enter the Connect mode When BTH 200 is turned on it will automatically be linked to the last device to which it was linked to on A
3. BTH 200 Bluetooth Headphone User Manual BTH 200 DIAGRAM 1 Charging port 3 Soft gel ear tips 5 Volume control button 7 Microphone 2 Ear loop 4 Multifunction button PTT 6 Status Indicator light EAR TIP SELECTION and ADJUSTMENT Ear y f f SSS at Za 1 2 3 4 z K USING BTH 200 Call answering Short press the multifunction button to answer an incoming call or to answer the call using the Bluetooth device and then transfer the call to BTH 200 Call termination Short press the multifunction button to terminate an active call or hang up the call using the Bluetooth device Make a phone call Make a phone call from the Bluetooth device Depending on the setup of the Bluetooth devices it might switch the call to the headphone Volume adjustment Push the Volume Control Button back and forth to change the volume level during the call PTT Press the multifunction button if link to a radio dongle The BTH 200 headphone comes with three large and small sizes soft gel ear tips and an optional ear loop The ear loop and large size ear tip are installed on the headphone 1 Turn the ear tip clockwise to position R and fix it on the right ear 2 Turn the ear tip counter clockwise to position L and fix it on the left ear 3 Hang the headphone on your ear and examine if it fits If not then replace it with a suitable one 4 Turn the ear tip to position N as shown in the diagram and it can be
4. removed To avoid damaging the ear tip hold the bottom of the ear tip as shown on the Marked spot before pulling Use a suitable ear tip hold it downward to position N and fix it on the headphone Then turn it to position R or L 6 When not in use please lock the ear tip at either R or L position to avoid drop off on Marked spot 4 EAR LOOP The ear loop enhances the stability of the headphone It was installed on the headphone If you would like to switch it to the other ear then you can remove it from the headphone turn it over to the other side and re install it on the headphone BTH 200 STATUS INDICATOR Status Status Indicator Light Stand by Blue light twice flashes every 2 seconds Connect Blue light flashes 3 times every 2 seconds Pairing mode Blue red lights flash alternativel Low batter Red light flashes Charging battery Red light on for charging light turns off when charging is done PRODUCT SPECIFICATIONS Version Bluetooth V3 0 EDR Class 2 Talk Time About 15 hours with SLP radio dongle Standby Time About 150 hours Charge Time About 2 hours Range About 10 meters Charger 5V DC 150 mA Battery Type Lithium ion battery CONTENT OF PACKAGE Examine the package and make sure that it contains the following items If any item is missing or damaged please contact your sales agent immediately e One 1 Bluetooth headphone One 1 ear loop Two 2 ear tips in large and small
5. t harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the radio or television off and on the user is encouraged to try to correct interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on another circuit 4 Consult the dealer or an experienced radio TV technician for help EXPOSURE TO RADIO FREQUENCY RADIATION This device and its antenna must not be collocated or operated in conjunction with any other antenna or transmitter To comply with FCC RF exposure requirements only use supplied antenna Any unauthorized modification to the antenna or device could void the user s authority to operate this device 7 PAIRING and LINK Before using the headphone for the first time one must pair it with other Bluetooth devices The following procedure describes how to do paring between BTH 200 and typical Bluetooth phones The pairing procedure to different Bluetooth devices may vary depending on
Download Pdf Manuals
Related Search