Car amplifier JBL GTO24001 1
Contents
1. s output circuit has failed DC voltage is present in the amplifier s output Setting Input Level EN Turn Input Level control counterclockwise to 6V minimim E With a dynamic music track playing turn the head unit s volume control to the 3 4 position Turn Input Level control clockwise until the bass output is proportionate to the output of the high frequency speakers according to your preference BD Input level is now adjusted correctly Setting the Crossover FN Crossover setting for subwoofers Note Acceptable frequency ranges are indicated in gray Remote Level Control Optional The Remote Level Control if installed will allow you to adjust the level of bass while seated in the listening position This product is designed for mobile applications and is not intended for connection to the mains A valid serial number is required for warranty coverage Features specifications and appearance are subject to change without notice JB www jbi com Car audio and car goods internet store Winauto Harman International Consumer Division 8500 Balboa Boulevard Northridge CA 91329 USA www jbl com 2009 Harman International Industries Incorporated All rights reserved JBL is a trademark of Harman International Industries Incorporated registered in the United States and or other countries Y Part No GT0240010M 7 09 H Harman International Declaration of Conformit2. Wa be Nay SN hd i Gib User s Manual Car amplifier JBL GTO24001 1 channel In the online store Winauto you also can buy car amplifier JBL GTO24001 Delivery in Kiev and throughout Ukraine with payment upon receipt http winauto ua j dandana cgl A Sa a a TSS i 4 Car Receivers Facia Plates Head Units TV and Monitors Car Antennas Car Audio Car DVRs GPS Navigation Trip Computers Security Systems Mechanical Locking Car Park Systems Cameras Optic and Light Car Tuning Car Heating Marine Audio and Electronics Car Accessories Car Isolation Car Installation Components Car Batteries Liquid and Oil MEGA o seve camino SCastrol Car audio and car goods internet store Winauto GTO24001 OWNER S MANUAL Car audio and car goods internet store Winauto rll POWER GTO24001 Car audio and car goods internet store Winauto GTO24001 CAR AUDIO SUBWOOFER AMPLIFIER OWNER S MANUAL Installation Warnings and Tips e Disconnect the negative lead from your vehicle s battery e At the insta
3. h pieces of 4 gauge 4 AWG 22mm wire through the car using rubber grommets in all locations where the wire must pass through metal Connect the other end of the 4 gauge 4 AWG 22mm wire to the two terminals on the amplifier s power connectors refer to illustrations page Figure 1 Fuse Holder 22mm 150A Inside Engine Compartment e For competition installations replace the fuse with a 300A ANL not included Connect a single piece of 0 gauge 0 AWG 53 5mm wire to the other end of the fuse holder as in Figure 2 Route the 0 gauge 0 AWG 53 5mm wire through the car using rubber grommets in all locations where the wire must pass through metal Connect the other end of the 0 gauge 0 AWG 53 5mm wire to the input terminal of a power distribution block not included designed to accept 0 gauge 0 AWG 53 5mm wire Connect two pieces of 4 gauge 4 AWG 22mm wire to the distribution block and connect the other ends of the wire to the two terminals on the amplifier s power connectors refer to illustrations page Figure 2 Factory Bolt Ring Connector Ground Wire y Note Remove any paint Star Washer below ring connector e REM Connect to the Remote Out lead from the source unit or to a source of switched 12V ACC Aux Output Connectors RCA e Nonfiltered pass through output Connect to the input of an additiona
4. l amplifier Input Connectors RCA e Connect to the RCA outputs from the source unit or signal processor Input Level Control e Used to match the input level of the amplifier to the output level of the source unit e See for the adjustment procedure Low Pass Filter Frequency Control e 12dB octave low pass filter variable from 32Hz to 320Hz e See for the adjustment procedure DBO Dynamic Bass Optimization Variable Subsonic High Pass Filter With Variable Boost Q e For woofers in tuned vented enclosures set the Frequency control to a value 10Hz below the enclosure s resonance tuned frequency e For woofers in sealed boxes set the control to any value you prefer between 30Hz and 50Hz e Set the Boost control according to your preference being careful not to apply enough boost to damage your woofer s N DBO High Pass Filter Frequency control variable between 10Hz and 100Hz See above for appropriate settings E DBO Boost control provides up to 12dB of boost slightly above the high pass filter s frequency See above for appropriate settings Optional Remote Level Control RLC Connector e Connect the Remote Level Control RLC here using the RJ 11 cable supplied with the RLC Power On LED e Illuminated when the amplifier is on Protect LED e Illuminated under any of the following fault conditions battery over under voltage short circuit in speaker wires amplifier is too hot amplifier
5. llation sites locate and make a note of all fuel lines hydraulic brake lines vacuum lines and electrical wiring Use extreme caution when cutting or drilling in and around these areas e Choose a safe mounting location away from moisture e Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself e Mount the amplifier using the supplied hardware Specifications e 1700W RMS x 1 channel 4 ohms and lt 1 THD N e 2400W RMS x 1 channel 2 ohms 14 4V supply and lt 1 THD N e Frequency response 20Hz 330Hz 3dB e Maximum input signal 6V e Maximum sensitivity 200mV e THD N 0 5 e Signal to noise ratio 65dBA reference 1W into 4 ohms e Signal to noise ratio 97dBA reference rated power into 4 ohms CEA 2006A compliant Speaker Output Connectors e Connect the speakers to these terminals observing proper polarity Either or terminal may be used Minimum total impedance is 2 ohms Fuse Holder 12V Connection e Replace fuse only with the same type and rating e Mount the fuse holder within 18 45cm of the vehicle s battery inside the engine compart ment and connect one end of the fuse holder to the battery s terminal using a single piece of 0 gauge 0 AWG 53 5mm wire as shown in Figures 1 and 2 e For normal installation connect two pieces of 4 gauge 4 AWG 22mm wire to the other end of the fuse holder as in Figure 1 Route bot
6. y cE We Harman Consumer Group Inc 2 route de Tours 72500 Ch teau du Loir France declare in own responsibility that the product described in this owner s manual is in compliance with technical standards EN 55013 2001 A1 2003 EN 55020 2002 A1 2003 Klaus Lebherz Harman Consumer Group Inc Ch teau du Loir France 12 08
Download Pdf Manuals
Related Search