User Manual
Contents
1. 12 Fig 6 Mounting on the dash console etc Fig 5 Camera Connector Electrical Shrink Tape Applied Properly 13 POWER INPUT RED To Ignition Switched Accessory Fuse 2A 250V 5x29mm Example McMastar Carr P N 6978K749 Radio Shack P N 2103766 n GROUND WIRE BLACK To metal point of the vehicle CA2 cava WHITE Trigger Wire REVERSE CAM1 lx GREEN Trigger Wire REVERSE Note For typical single camera installation this trigger wire should be connected to the vehicle s back up lights circuit and the rear view camera should be attached to the connector marked REVERSE 14 VisionSystems 90 21 144th Place Jamaica NY 11435 www roscovision com Ph 1 800 227 2095 Fx 1 718 297 0323 ISO 2001120009 FM 78496 Century of QS 9000 March 1998 FM 78495 E Printed in China Automotive Safety Lit P N 042420122. 1 The camera to cable connection is waterproof Be sure to position the cable properly The male end attaches to the camera The female end attaches to the power video audio distribution harness typically located under the dashboard See Fig 7 IMPORTANT For typical rear view installation the rear camera MUST be connected to the distribution harness at the connector marked REVERSE 2 Do not run the cable over sharp edges or corners Do not kink the extension cable Keep the cable away from hot and rotating parts 3 Stretch and tightly wrap tape around section where connectors meet Cut excess tape if any Place hand over taped area and squeeze tightly This will ensure a tight fit Over time tape will tighten more See Fig 5 4 Fasten all cable runs and secure all excess cable 5 WIRING CAMERA AND MONITOR Monitor 1 Connect the red wire to an ignition switched accessory ex radio power source and connect the black wire to chassis ground See wiring diagram for connections See Fig 7 2 Monitor The monitor terminates in a 13 pin connector which should be connected to the mating 13 pin receptacle end of the power video audio distribution harness 3 For typical rear view installation connect the camera extension cable from the rear view camera to the harness s connector marked REVERSE 4 For multi camera installations be sure to mark each extension cable properly and connect to the appropria
3. 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation E 1 3 1 High voltages exist within the monitor Opening of monitor case is unsafe and never necessary for operating purposes 2 In case of any failure please tum off the display at once and notify our company or the corresponding dealer The monitor and camera are made up of many precise electronic components Any disassembly or modification may lead to damage and voiding of warranty ROSCOE VisionSystems C1 C2 MODE MENU VOL cl 2 POWER E Bro Front view 1 Mini Switches Turns mirror function on and off for Camera 1 and Camera 2 2 C1 C2 Switches from camera 1 to camera 2 and vice versa 3 Mode Day Night Dimming amp Menu Control 4 Menu Switches to setup mode See p 8 for options 5 Volume amp Menu Control Increases amp Decreases Volume amp Adjust Menu settings 6 Cam 1 Indicator amp Brightness Control 7 Cam 2 Indicator amp Contrast Control 8 Color Indicates dimming status amp Tint Control LED is lit orange if the monitor is operating in day mode 9 Power Switch Switches Monitor from Stand by to Steady on COLOR BACKUP CAMERA SYSTEM STSK5465 INTRODUCTION Please read this manual thoroughly This manual contains instructions to make the installation of the camera and monitor easier The color backup cam
4. selected when monitor is in Steady on green light mode When monitor is in standby mode and activated by trigger sig nal on screen menu commands are disabled Press the MENU button once to set desired brightness Press and hold to reduce the brightness Press and hold to increase the brightness Press the MODE button to exit setup mode Press the MENU button twice to set desired contrast Press and hold to reduce the contrast Press and hold to increase the contrast Press the MODE button to exit setup mode Press the MENU button three times to set desired tint Press and hold to reduce the tint Press and hold to increase the tint Press the MODE button to exit setup mode NOTE You can reset the monitor to the factory settings for brightness contrast tint and volume To do this proceed as follows Press the MENU button once The LED C1 starts flashing Press the C1 C2 button Factory settings are set SPECIFICATIONS STSC141 CAMERA PICK UP DEVICE TV SYSTEM PICTURE ELEMENTS SENSING AREA IMAGE SIZE SYNCHRONIZATION HORIZONTAL RESOLUTION REQUIRED ILLUMINATION SIGNAL TO NOISE RATIO POWER SUPPLY POWER CONSUMPTION CURRENT CONSUMPTION LENS ANGLE OPERATION TEMPERATURE STORAGE TEMPERATURE WEIGHT DIMENSIONS W x H x D STSM241 MONITOR SCREEN 5 0 inch 127mm DEFLECTION ANGLE POWER CONSUMPTION POWER SOURCE TV SYSTEM VIDEO INPUT OUTPUT RESOLUTION CON
5. TRAST BRIGHTNESS VIEWING ANGLE U x D x R L OPERATING TEMPERATURE STORAGE TEMPERATURE WEIGHT OUTER DIMENSIONS WxHxD DISCLAIMER INTERLINE TRANSFER TYPE CCD PAL NTSC 512 H x 582 V PAL 512 H x 492 V NTSC 0 2x0 1in 4 9mm x 3 7mm 1 4 inch INTERNAL 420 TV LINES 0 LUX MINIMUM F 1 2 MINIMUM 48dB AT AGC OFF 12Vde 3 5W AT 12Vdc MAX 200mA 120 D 88 H 66 V 22 F to 149 F 20 F to 176 F 0 6Kg 0 4115 3 x 2 x 2in 75 x 48 x 49mm COLOR TFT LCD 50 LEFT RIGHT 15 TOP 35 DOWN 8W 700mA MAXIMUM 12 30Vde PAL NTSC COMPOSITE VIDEO SINGLE 1VP P 75 OHM 960 H x 234 V 350 1 400cd m2 15 x 30 x 50 5 F to 149 F 13 F to 176 F 0 4Kg 0 8015 5 7 x 4 3 x1in 144 x 110 x 25mm without flush mount The use of the STSK5465 Vehicle CCTV system should not in any way be used as a substitute for careful and cautious driving Always obey traffic laws and motor safety regulations must always be adhered to Specifications subject to change without any notice Fig 1 7 Camera mount in suggested location Mount camera assembly high Centered Camera mounting hole pattern 60 30 THRU Fig 2 Position of camera Vehicles behind truck Street Rear Bumper Typical monitor image of view from properly installed camera 11 Fig 3 Optional wind deflector Fig 4 Back of Bracket fr lrn Front of Bracket
6. VisionSystems Safe T Scope 5 Rearview Backup Camera System INSTALLATION USER S MANUAL STSK5465 90 21 144th Place Jamaica NY 11435 1 800 227 2095 www roscovision com WARNING To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are dangerous voltages inside the monitor There are no user serviceable parts inside 2 Avoid exposing monitor to water rain moisture etc It is NOT waterproof Any moisture inside the monitor could cause extensive damage 3 Do not disassemble the camera This voids the warranty Disassembling the camera will compromise the waterproof seal 9 STORAGE 1 Do not expose the monitor to excessive heat or cold Storage temperature 15 170 F and operating temperature is 5 150 F 2 Do not store or operate in humid environments 9 GENERAL 1 This system is intended for use in automotive applications Power source should be an automobile storage battery 12V 24V 2 Make sure all cables are connected properly Improper cable connections may damage the monitor Remove the cable connection when you do not intend to use the unit for a long period of time 3 Please install this system according to the instructions in this manual 4 Connect the system to an ignition switched power source Connection to an unswitched battery source will reduce battery life This device complies with Part 15 of the FCC Rules Operation is C subject to the following two conditions
7. er to the wiring diagram Fig 7 and the particu lar vehicle s electrical schematic for selection of proper power and trigger connection points FUNCTIONS AND OPERATION MONITOR 1 MINI SWITCHES Both mini switches activate the mirror function for Camera 1 or Camera 2 2 POWER When the ignition is switched on the monitor will be in standby mode no image will be on the screen waiting for trigger signal When a trigger wire is energized by 12v power such as backup lights turning on the image captured by the selected camera will appear on the monitor 3 Pressing the power switch will change the monitor status from standby to steady on Steady on mode status will show rear cameras view 4 VOLUME Adjust Speaker Volume These buttons are also used to adjust the values within selected setting of menu option 5 MENU Button See p 8 Press the MENU button once to set desired brightness Press the MENU button twice to set desired contrast Press the MENU button three times to set desired tint 6 MODE Switching the monitor to day or night mode Press MODE The monitor is switched from day mode to night mode or vice versa The LED COLOR will be orange if the monitor is operating in day mode The LED COLOR will be green if the monitor is operating in night mode 7 C1 C2 Switches from Camera 1 to Camera 2 and vice versa HOW TO SET YOUR MONITOR TO YOUR REQUIREMENTS NOTE On screen menu commands may only be
8. era system is a supplement to standard rear view mirror systems and will provide additional rear view vision when installed and maintained properly It is not intended in any way to be a substitute for careful and cautious driving All applicable traffic laws and motor vehicle safety regulations must still be obeyed FEATURES STSC141 CAMERA 270 000 pixel image sensor 0 1 Lux sensitivity 18 IR LED Field of view 120 Diagonal Back Light Compensation BLC Automatic electronic iris provides a clearer more consistent image in low and bright light Compact and lightweight design installs easily into most vehicles Waterproof dustproof IP67 rating Wind deflector reduces buildup of dirt on lens STSM241 TFT LCD COLOR 5 MONITOR Menu Control for Picture System and Options Camera 1 Camera 2 Power stand by switch Powerful built in speaker Expansion Capability System can Accept up to 2 Camera Inputs CONTENTS OF COMPLETE SYSTEM 1 Camera with Accessories Mounting Bracket w hardware Wind Deflector 65 Camera extension cable 1 Monitor with Accessories Sunshield Duckfoot universal bracket for surface mounting of monitor on dashboard or headliner including adhesive pad Power Video Audio Distribution harness for up to 2 Cameras IMPORTANT For typical rear view installation the rear camera MUST be connected to the distribution harness at the connector marked REVERSE N
9. ote The following instructions are for typical rear view application STSC141 CAMERA 1 Attach camera bracket close to rear marker lights centered on vehicle see Fig 1 Attachment point must be sturdy enough to support camera and bracket 2 We do not recommend mounting the camera near the lower area of the vehicle ex bumper This reduces the view of the camera and increases the chance of physical damage to the camera Before installing bracket to designated area place gasket on the back of the bracket Place screw grommet on both top and bottom positions then tighten screw to hold in place Fig 4 p 13 shows how the bracket gasket grommet amp screws should be installed Apply to vehicle and tighten to secure bracket into place Attach camera to bracket using screws provided Adjust angle as indicated in Fig 2 Use rear bumper and back of vehicle as a reference point 8 Wind deflector may be installed This deflector is designed to reduce the buildup of dust dirt and moisture on the camera lens See Fig 3 STSM241 MONITOR 1 Attach monitor inside vehicle in a location convenient to the driver ex center of dash overhead or flush mounted in dash 2 Attach the duckfoot bracket to the dashboard or to the headliner using self tapping screws and or adhesive pad N aooe 3 Fasten monitor to duckfoot and adjust mounting angle to allow optimum driver viewing comfort See Fig 6 STSH341 CAMERA EXTENSION CABLE
10. te harness connector marked CA1 or CA2 Bundle excess cable together using a cable tie or electrical tape 5 The green wire is the REVERSE trigger wire In typical rear view installations connecting this wire to the vehicle s backup light circuit will activate the rear view image whenever the vehicle shifts into reverse 6 Camera Drill a 20mm 0 8in diameter hole into vehicle body near the camera and bracket Insert camera cable into vehicle be careful not to kink cable and fit grommet into hole Apply sealant around grommet to increase resistance to water penetration Connect camera to the camera extension cable which runs inside the vehicle 7 Feed as much cable as possible into vehicle and clamp securely This reduces the possibility of it being hooked or snagged 8 Keep all cables away from HOT ROTATING and ELECTRICALLY NOISY components 9 FUEL TANKERS amp OTHER SPECIALTY VEHICLES All electrical equipment fitted to petroleum vehicles must be connected via battery master switch and must be isolated from the battery while the vehicle are loading and unloading For other specialty vehicles please check applicable code and regulations prior to installation 10 Always consult your dealer when fitting any electrical or electronic equipment to a vehicle fitted with a CAN bus or multiplex system IMPORTANT For installations requiring multiple cameras or for installations not requiring typical rear view images please ref
Download Pdf Manuals
Related Search