WILD RIDE ™ SLIDE - Inter-Fab
Contents
1. 2 deep make sure you drill to the correct depth and make sure not to drill all the way through the deck Gently hammer the bolt into the hole in the deck with 3 4 1 of the bolt above the deck Gently lift and reposition the slide deck anchors and the L brackets over the bolts Put anti seize on the bolts then flat washer and nut secure the nuts on the bolts but do not over tighten See Fig 14 NOTE If you are Deck Anchor installing slide onto a deck using pavers refer to optional Wild Ride Paver Kit info on page 13 Deck Line Uim eae Fig 14 CHECK YOUR LOCAL ELECTRICAL CODE FOR BONDING REQUIREMENTS STEP THIRTEEN n Deck Installation Attach slide legs to the higher of the 2 bolt holes on the deck anchor hole make a mark with a marking pen or duct tape 4 1 4 from the bottom of the deck anchor shim the legs so the mark you made on the deck anchor is flush with the finished deck using a bubble level ensure the legs are plumb Pour concrete to secure legs ensure the proper footing depth Is maintained under the deck anchor See Fig 15 Deck Anchor P Concrete Deck Deck Line 9 3 16 Fig 15 WRS IM Rev 7 15 SBKINST WRS INSTALLATION MANUAL WILD RIDE SLIDE STEP FOURTEEN Attach Water Supply to Slide Olip the provided 1 flex pipe through the hose hanger rings along the underside of the step You can use either the right or the left hand side T2. Tips amp Tools for Slide 6 1 Measure the Pool LY eee e nena 7 Step Flume Assembly esses 3 Legs to Flume 7 Step 4 Attach Deck Anchors to otep a Assemble SteDpS Y LL FL Y LL LL RF YL LY Y dyu 6 Stand Up the Attach 1 Brackets to 8 Align Flume SectiOnS I Y LL eee 9 Attach Handrails to step 10 Attach Steps to Flume esses 11 Place Slide in Final 10 12 On Deck Installation YYY YY YL RR FF FY Y uad 10 13 In Deck InstallGtlOD Y Y YY LL RR RF Y Yu ud 10 Step 14 Attach Water 1 1 Step 19 Attach Protective 1 1 Step 16 Provide Homeowner with Owner s Manual 11 Inspection Check 1 1 olide amp Maintenance sss RG FF 12 Paver Kit INStall tion cece cece cec
3. nber fa LOM WILD RIDE SLIDE Assembly amp installation Instructions IMPORTANT THESE INSTRUCTIONS MUST REMAIN WITH THE SLIDE OWNER Visit inter fab com to view our installation help video Video does NOT replace installation instructions WARNING IMPORTANT INSTALLATION INFORMATION The installation of this product should be done only by a licensed and professional installer Installation should be done strictly in conformance with all local building codes electrical codes and other building and safety laws and regulations Among other things that your installer should carefully analyze the need to bond the product to prevent an electrical hazard Failure to properly install this product could result in a dangerous condition including but not limited to electrical or structural hazards Inter Fab Inc disclaims all liability arising from the installation and the user assumes all risk associated with the installation INTER FAB INC 3050 S ALVERNON WAY e TUCSON AZ 85713 920 790 7040 800 737 5386 FAX 520 790 7127 inter fab com WRS IM Rev 7 15 SBK INST WRS INSTALLATION MANUAL WILD RIDE SLIDE TABLE OF CONTENTS Intended Use Instructions LL FF cece c Water Safety mns 3 olde Placement amp Footprint Diagrams Left 4 Slide Placement amp Footprint Diagrams Right Turn
4. 2 years from the date of original shipment The battery charger receiver control box on rLift transmitter remote and actuator have a warranty period of one 1 year from the date of original shipment Unless expressly stated otherwise all products manufactured by Inter Fab are for residential installation single family residence inground pool use only Inter Fab Inc expressly disclaims any and all warranties and liability arising from the installation or use of its residential products for any non residential use such as semi public public or commercial applications Products expressly manufactured for commercial installation and use will be subject to this limited warranty This limited warranty is in lieu of all other warranties whether express or implied Inter Fab Inc disclaims any warranty of merchantability or fitness for a particular use and noninfringement in relation to any of its products and Inter Fab Inc is not liable for consequential incidental or specific damages This warranty is limited to the repair or replacement of the manufacturing or material defect or refund of the original purchase price whichever is less at the sole option of Inter Fab Inc and expressly does not cover any labor or reinstallation expenses related to the replacement of any and all Inter Fab products This limited warranty shall be the sole and exclusive remedy of irrespective of whether the claims are made in contract tort warranty law
5. equity or by statue This warranty is to the original purchaser of the product only Inter Fab s limited warranty is neither transferable nor portable from consumer to consumer The effective coverage date begins at the date of retail purchase Product owner or representative must notify Inter Fab Inc or its wholesale agent in writing giving a full description of the nature of the product defect or failure along with proof of purchase serial number s of the product and photos within thirty 30 days of the expiration of the applicable warranty period Inter Fab Inc reserves the right to physically inspect damaged or defective products or components to determine the cause of the damage or defect prior to authorizing repair or replacement of its products ncer fau 3050 S Alvernon Way Tucson AZ 85713 220 790 7040 800 737 5386 Fax 520 790 7127 inter fab com WRS IM Rev 7 15 SBK INST WRS 18
6. INIMIZE SEIZING HARDWARE TIP Use the box the slide came in to assemble the flume sections and step sections to keep them from being scratched TIP Have rag handy to wipe the anti seize off your finger or you will get it on the slide and it is difficult to get off TIP Use vice grips or clamps to hold the flume sections as well as the step sections together during assembly For Technical Support or Assistance Contact Customer Service at INTER FAB INC 3050 S ALVERNON WAY TUCSON AZ 85713 800 737 5386 or visit www inter fab com WRS IM Rev 7 15 SBK INST WRS INSTALLATION MANUAL WILD RIDE SLIDE ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP ONE Measure the Pool Using the slide placement information on pages 4 and 5 choose the location and position for the slide Next measure the pool in front of where the slide will be installed and ensure it meets the minimum water safety envelope and clearance requirements Inter Fab highly recommends that only the fully assembled slide be utilized to mark the locations for the anchor bolts Fig 1 Fig 2 Fig 3 STEP TWO Assemble Flume Sections TIP Use the anti seize provided on all bolts to prevent hardware from seizing Align the bolt holes in the flume flanges use vice grips or clamps to hold the flanges in place Using hardware kit SH 102 55 in this order take bolt flat washer push through both flanges flat washer then nut See Fig 1 Fig 2 an
7. INST WRS 14 INSTALLATION MANUAL WILD RIDE SLIDE WILD RIDE SLIDE wns cn ss ALL CHART INFORMATION BELOW CORRESPONDS WITH THE DRAWING ON THE PREVIOUS PAGE lt SH 101 Handrails Step to Step H 102 Flume to Flume Leg to Flume SH 103 Step to Deck SH 104 Protective Caps SH 106 Deck Anchors to Legs Deck Anchor to Deck DRAWING REPRESENTS THE FOLLOWING PART NUMBERS SH 107 Deck Anchor SH 108 Step to Flume SH 107 HARDWARE KITS PARTS KITS QTY COUNTS DESCRIPTION WRS URUN W R WRS LRUN W R WRS USTEP W WRS HD RAIL WW 24 1 2 LEG WW 22 LEG WW 54 1 2 LEG H WRS WW GASKET DECK ANCHOR 463 X 310 CAP H 562 Y 390 CAP H 1 BALL VALVE H 1 SPA HOSE H 1 WHT CAP 750 X 1 GRAY NUT CAP H SS 1 2 F WAS 1 2 FLAT WASHER 5 5 H SS 1 2 13 BOL 1 2 X 1 1 2 HEX HEAD BOLT S S H SS 1 4 FL HEAD HSS 1 4 FLAT W H SS 1 4 H NUT HS 1 4 X 1 1 4 F H SS 1 4X2 1 4H 55 3 8 F NUT H SS 3 8 FLT WASHER 55 3 8 WEDGE MSS 3 8X1 H B HSS 3 8X1 3 4 BRACKET H SS 1 4 20 X 1 1 4 X 1 HEX HEAD BOLT S S BENI EE XN 3 O4 o9 0 0 OB Ou 16 OB 19 Om OH Om 3 NN o Lom i ISS Ww not pictured Comes with one 1 deck anchor and one 1 SH 106 kit Must order one for each leg of the slide 4 total 4 are included when ordering a complete slide NOTES Wild Ride Slides a
8. UAL WILD RIDE SLIDE SLIDE PLACEMENT DIAGRAM amp FOOTPRINT DIAGRAM Wild Ride Slide Right Turn DIAGRAM F ALWAYS ALONG THIS ARC NOT TO SCALE GRID INCREMENTS IN FEET BENE Llu LL _ N I Le ADD LLEW CR AN Y ATI INI I NNLLA WA 9 eee LE ALLA LEA ae AF 3 MINIMUM etek Xe s OVERHANG DIAGRAM G NOT TO SCALE EE REN DIN DECK AREA 12 0 a T 5 10 3 4 d i Fa 9 3 4 2 7 1 4 EL Eus ns 4 1 I Seen i 2 6 5n E SUGGESTED STUB UP 740 9 1 4 ct hol LOCATION c 1 6 MIN y Y y y POOL EDGE ROTATE ABOUT THIS POINT AS DESIRED RECOMMENDED MAINTAIN MINIMUM MIN DECK AREA DISTANCES AS SHOWN 12x 5 10 5 3 4 a 10 11 WRS IM Rev 7 15 SBK INST WRS 5 INSTALLATION MANUAL WILD RIDE SLIDE RECOMMENDED TOOLS FOR ASSEMBLY AND INSTALLATION OF G FORCE SLIDE ASSEMBLY TOOLS e Socket wrench e 16 9 16 amp 3 4 sockets and extensions e 16 S 9 16 wrenches e 5 32 Allen wrench e Hammer Drill e 3 8 masonry drill bit not shown e Vice Grips or Clamps Optional not shown e Step stool ladder not shown e Center Punch NOTE USE PROVIDED ANTI SEIZE ON ALL BOLTS READ THIS ENTIRE INSTALLATION MANUAL BEFORE ATTEMPTING THE INSTALLATION TIP USE ANTI SEIZE PROVIDED OM ALL BOLTS TO M
9. d Fig 3 Hand tighten only at this point Fig 4 Fig 5 STEP THREE Attach Legs to Flume TIP Use the anti seize provided on all bolts to prevent hardware from seizing The 2 longer legs attach to the upper flume section The shortest leg attaches to the inside curve of the lower flume See Fig 5 Using hardware kit SH 102 98 slip leg over the leg receiver on the flume Align the predrilled holes then in this order take bolt flat washer push through leg and receiver then flat washer then nut INTER FAB WILD RIDE SLIDE MUST BE INSTALLED USING THE PROVIDED STEEL DECK ANCHORS OR YOU WILL VOID THE WARRANTY WRS IM Rev 7 15 SBKINST WRS 7 INSTALLATION MANUAL WILD RIDE SLIDE STEP FOUR Attach Deck Anchors to Legs TIP Use the anti seize provided on all bolts to prevent hardware from seizing For On Deck Installation slip the leg over a deck anchor as shown See Fig 6 Align the predrilled holes in the leg with the lower hole in the deck anchor using hardware kit SH 106 S8 In this order take bolt flat washer push bolt through the leg and anchor then add flat washer then nut Repeat this step for all 4 legs and tighten nuts Fig 6 Fig 7 STEP FIVE Assemble Steps TIP Use the anti seize provided on all bolts to prevent hardware from seizing Align the holes in the step sections using a vice grip hold the 2 sections together then using hardware kit SH 101 S5 in this order take bolt flat washer pus
10. e cece eee RL e 13 Exploded View of White Water 14 Parts List corresponds with exploded view 19 Hardware Kit InformatiODn IL cece LL FF 16 inr Y ee ee 17 Inter Fab Inc Limited VVarranbty FFFFF RR YY Y nuu 18 WRS IM Rev 7 15 SBKINST WRS 1 INSTALLATION MANUAL WILD RIDE SLIDE INTENDED USE INSTRUCTIONS 1 Everyone who uses this slide must know understand and follow these instructions 2 The ANSI APSP ICC 5 2011 standard for above ground pools prohibits the use of slides or diving boards on above ground pools 3 This Slide is designed for residential inground pool use ONLY This slide may not be used on any above ground pool Such use of this slide may result in serious injury or death 4 This slide should never be installed on above ground pools ponds floating docks or platforms boat docks or houseboats or any natural body of water o This slide should never be installed on any commercial public or semi public pool 6 Be Familiar with the shape and depth of the pool before you slide This slide should only be used with the proper water safety envelope as described in Diagrams A B and C page 3 and in accordance with the slide positioning instructions as described in Diagrams D E F and G on pages 4 and 5 Because the slide may only be used in water 4 deep or greater all slide users must be able to swim in d
11. e owner s manual to the customer and go over the INTENDED USE INSTRUCTIONS with them WRS IM Rev 7 15 SBKINST WRS 11 INSTALLATION MANUAL WILD RIDE SLIDE SLIDE CARE amp MAINTENANCE ACRYLIC amp POLYETHYLENE COMPONENTS 1 General Cleaning e Use nonabrasive soap and water when possible e Review cleaner s label instructions before applying to acrylic surface e Avoid harsh chemicals and disinfectants You may safely use e Chlorox e Spic amp Span Powder e Mr Clean e Formula 409 e Windex e Glass Plus e Calgon Bath Oil Beads Do not use e Lysol Disinfectant Spray e Dow Disinfectant Bathroom Cleaner e Pinesol e Whitecap e estoil 2 Light scratches abrasions gloss etc Light abrasions and scratches may be removed and original gloss fully restored using the following materials e Novus Plastic Polish Novus Inc e Mirror Glaze Professional Formula 17 Mirror Bright Polish Co Irvine CA e Permatex Plastic Cleaner 403D Permatex Co Kansas City KS e J Wax or Kit Automotive Cleaner Waxes S C Johnson amp Son e DuPont or Turtlewax White Polish automotive polishing compound Light Scratches Very light scratches scuff marks and haze can be hand polished with Permatex Plastic Cleaner or Gel Glass Follow the manufacturer s guidelines Clean cotton cloth works best for applying the polish and buffing These suggestions and data based on information we believe to be reliable from o
12. eep water Weight limit for this slide is 250 pounds no slider weighing more than 250 pounds may use this slide 9 The surface of the slide is very slippery when wet USE CAUTION when entering the slide and when transitioning from standing to sitting 10 Slide in a feet first sitting position ONLY 11 IMPORTANT sliding headfirst is prohibited serious spinal injury resulting in paralysis or death can result 12 Maintain adult supervision at all times 13 Only one person at a time Is allowed on the slide this includes the ladder 14 Be sure the water delivery system is on and lubricating the slide prior to use 19 Collision with another swimmer or a diver can result in serious injury or death for one or both persons Before sliding always make sure that the path in front of the slide is free from any including submerged obstructions including other people or objects in the pool such as rafts inner tubes etc When a diving board is also present make sure you do not use the slide while someone is on or using a diving board Take turns 16 No roughhousing or horseplay should be allowed on the slide at any time 17 Do not stand jump or dive from any part of the slide 18 Do not slide on objects such as rafts or inner tubes doing so greatly increases your risk of injury 19 Do not slide through or at objects such as rafts or inner tubes doing so greatly increases your risk of injury 20 Do not use this slide if physically i
13. exposed above the final deck surface The 3 8 wedge anchors must be drilled to a depth of 6 with 1 of the bolt left remaining above the final deck surface The 3 8 x 7 wedge anchors 14 ea replace the 3 8 x 2 3 4 wedge anchors ea from hardware kit SH 108 and the 3 8 x 2 3 4 wedge anchors 12 ea from hardware kit SH 106 You will need to factor in the thickness of your paver 3 MAX and the thickness of your setting material 3 8 MAX for your individual installation You will need a 3 8 masonry bit for the or Wild Ride slide Inter Fab Inc will not be responsible for damage to pavers caused by drilling or mechanically attaching to concrete pad Refer to paver manufacturer s specific installation instructions before beginning Minimum Concrete Pads Wild Ride Slide Example of Deck Anchor on Concrete Pad Side View Plan View NOT to Scale HEIGHT OF WEDGE ANCHOR ABOVE O concrete pads are needed FINAL DECK 1 12 wide x 32 long x 12 deep SURFACE 4 16 wide x 16 long x 12 deep Center feet on pads Layer of setting material to secure pavers to concrete from edge ANCHORS Pool Edge DAW 7 NN 16 min NOT To Scale CONCRETE Fig 19 Fig 20 WRS IM Rev 7 15 SBKINST WRS 13 INSTALLATION MANUAL WILD RIDE SLIDE WILD RIDE SLIDE wns cn ss DETAIL C DETAIL F N DETAILE gt B DETAIL D DETAIL G WRS IM Rev 7 15 SBK
14. h bolt through both step sections then place flat washer then nut Fully tighten the bolts but do not over tighten STEP SIX Stand the Slide Up Using 2 people to flip the slide over to its upright position When you flip the slide make sure you hold the flume DO NOT HOLD THE LEGS TO FLIP THE SLIDE OVER STEP SEVEN Attach the L Brackets to Steps Attach the L brackets to the inside bottom of the steps using hardware kit SH 103 GS See Fig 8 When installed correctly the brackets should sit flush with the bottom of the step sides See Fig 9 STEP EIGHT Align Flume Sections Align the flume sections for a smooth even sliding surface then tighten all the flume bolts Do not over tighten WRS IM Rev 7 15 SBK INST WRS 8 INSTALLATION MANUAL WILD RIDE SLIDE STEP NINE Attach Handrails to Steps TIP Use the anti seize provided on all bolts to prevent hardware from seizing Have one person lift the assembled steps then position the upper portion of the handrail over the hole located on the outer edge of the step seat See Fig 10 Then using hardware kit SH 101 SS and a 3 4 socket wrench with an extension take bolt then flat washer thread bolt up from the underside into the handrail Do not fully tighten at this time Repeat this process for the other 3 handrail attachment positions on this rail then repeat this process for the other handrail See Fig 11 Fig 10 Fig 11 STEP TEN Attach S
15. hen slip it through the underside of the seat See Fig 16 Using PVC glue attach the flex pipe to the water supply fitting under the flume See Fig 1 7 Using PVC glue attach on off ball valve near the deck above the water stub up See Fig 18 STEP FIFTEEN Attach Protective Caps Ensure that all bolts are securely tightened Place a protective rubber cap over each exposed bolt and nut STEP SIXTEEN Give the Owner s Manual to Homeowner Give the homeowner the Owner s manual and go over the intended use instructions with them FINAL amp ANNUAL INSPECTION CHECK LIST 1 Inspect the runway for visible cracks or tears 2 Inspect the edges of runway for sharpness loose cracks or tears 3 Inspect the slide for loose or corroded fasteners A Inspect all step attachment points for evidence of shear bending yield or fatigue Yield is evidenced by crystallization or fine cracking of the ladder tread or surface o Inspect the ladder handrails for rigidity and attachment can they be pulled out of their sockets 6 Inspect the slide for sharp edges or protrusions on the ladder deck flanges handrails or runway 7 Measure the depth of the water in front of the slide exit and measure height of exit and compare to Diagrams A B and C on page 3 Check the position of the slide exit to Diagrams D F and G on pages 4 and 5 9 Make sure the slide warning label is securely adhered to the slide 10 Personally Give th
16. int A The above described water depth profile shall extend a minimum of three feet three inches 3 3 on either side of the centerline of the slide See Diagrams A amp 6 6 3 3 3 3 1 3 6 DIAGRAM B NOT TO SCALE Minimum Slide Clearance Area DIAGRAM C NOT TO SCALE Minimum Water Safety Envelope 20 Max Water Level i DIAGRAM A NOT TO SCALE E IS i 3 J a fu ja 2 P m amp WATER SAFETY ENVELOPE Level Deck ALL SLIDES SHOULD BE GROUNDED Check your local electrical code requirements WRS IM Rev 7 15 SBK INST WRS 3 INSTALLATION MANUAL WILD RIDE SLIDE SLIDE PLACEMENT DIAGRAM amp FOOTPRINT DIAGRAM Wild Ride Slide Left Turn WATER STUB UP LOCATION ALWAYS ALONG THIS ARC DIAGRAM D NOT TO SCALE GRID INCREMENTS IN FEET 11 LOC eS MEN O7 AMENE er yN TH TF 18 MIN x a 3 MINIMUMI OVERHANG DIAGRAM E NOT TO SCALE RECOMMENDED MIN DECK AREA N 12 0 y 2 8 1 2 i RECOMMENDED MIN DECK AREA 12 x5 40 9 1 4 7 SUGGESTED STUB UP LOCATION MA N POOL EDGE ROTATE ABOUT THIS POINT AS DESIRED MAINTAIN MINIMUM DISTANCES AS SHOWN 10 5 3 4 10 11 WRS M Rev 7 15 SBKINST WRS A INSTALLATION MAN
17. mpaired or handicapped without your doctor s permission 21 Do not use this slide with a history of heart conditions seizures back problems fainting or fear of heights 22 Do NOT use this slide if you are pregnant 23 Do not drink alcohol and use this slide 24 Don t take chances inspect the slide at least once a year see the slide inspection list on page 11 do not use the slide if any part becomes loose damaged weakened or broken If necessary before using the slide again have it inspected and repaired by a competent professional familiar with pool slides WARNING SERIOUS INJURY OR DEATH CAN RESULT FROM THE IMPROPER INSTALLATION OR USE OF THIS SLIDE SLIDE IN A SITTING DO NOT SLIDE HEAD FIRST SERIOUS INJURY DEEP WATER POSITION ONLY d CAN RESULT AN SWIMMERS Face forward on the slide holding the legs and arms with the palms of your hands forward and tilted up When installed according to these instructions this slide conforms to Consumer Product Safety Standard Guidelines WRS IM Rev 7 15 SBK INST WRS 2 INSTALLATION MANUAL WILD RIDE SLIDE WILD RIDE WATER SAFETY ENVELOPE A minimum water depth of three feet 3 under the exit of the slide which increases to a depth of four feet 4 at point A which is located four feet six inches 4 6 from the back wall of the pool A minimum depth of four feet 4 must be maintained at a distance of nine feet 9 along the centerline of the slide from po
18. r products manufactured by Inter Fab Inc is three 3 years from the date of retail purchase except as specified below Echoes of Nature products are individually handcrafted and painted by skilled artisans and as a result dimensional differences and color variations are normal and are not a basis for warranty coverage The warranty period for pumps sold with the Echoes of Nature products is three 3 years from the date of retail purchase Water Sports sports equipment warranty periods are as follows Volleyball Poles Basketball Poles Basketball Rim and Basketball Backboard are one 1 year from date of retail purchase Volleyball Volleyball Net Basketball Basketball Net and pumps are warranted for ninety 90 days from date of retail purchase The Board Fall Board Fall L LED and Board Fall F fiber optic water features used for the Jump amp Splash T7 and aquaBoard products have a warranty period of one 1 year from the date of retail purchase Zoomerang slide products warranty period is one 1 year from the date of retail purchase Build Your Own Slide BYOS Build Your Own Slide 2 BYOS Garden Ride Series Pool Spa Table Pool Spa Seat and Pool Lifestyle products warranty periods are one 1 year from the date of retail purchase City 2 Slide and City Base products warranty period are one 1 year from the date of retail purchase Lift products warranty period are two
19. teps to Flume TIP Use the anti seize provided on all bolts to prevent hardware from seizing Gently place the steps against the upper flume then align the holes in the step section with the holes in the flume TIP Use a center punch or a screwdriver to gently align the bolt holes Then using hardware kit 5 108 55 insert the longer 3 allen head bolts in the 3 holes centered in the flume See Fig 12 Then from underneath in this order place flat washer then nut Then on the upper outside edge of the flume insert the shorter allen head bolts then add flat washer and nut Fully tighten all the step to flume bolts at this time but do not over tighten See Fig 13 Next fully tighten the handrail nuts u u UM EN WRS IM Rev 7 15 SBKINST WRS 9 INSTALLATION MANUAL WILD RIDE SLIDE STEP ELEVEN Place Slide in its Correct and Final Position Using 2 people gently move the fully assembled slide to its correct and final position on the deck CHECK YOUR LOCAL ELECTRICAL CODE FOR BONDING REQUIREMENTS STEP TWELVE Deck Installation Once the slide is in its final position then using a bubble level ensure the 4 legs are straight plumb next fully tighten the leg to flume bolts then using the deck anchor flange and the step L brackets as a template mark the locations for the anchor bolts Gently move the slide to one side Then using a 3 8 masonry drill bit and a hammer drill drill a hole 1 3 4
20. ur acrylic manufacturer They are offered in good faith but without guarantee as conditions and methods of use and procedures are beyond our control WRS IM Rev 7 15 SBKINST WRS 12 INSTALLATION MANUAL WILD RIDE SLIDE PAVER KIT INFO WILD RIDE SLIDE When installing an Inter Fab Wild Ride slide using a paver kit you must ensure that all standard installation requirements are met The slide must be compatible with the type of pool on the intended installation and all ANSI APSP ICC 5 2011 requirements must be met Refer to installation manual CHECK YOUR LOCAL ELECTRICAL CODE FOR BONDING REQUIREMENTS Figure 19 illustrates an example of the minimum concrete pads recommended for the and Wild Ride slides Specific slide position and concrete pad orientations may vary Make sure to allow for water stub up location near the ladder section of the or Wild Ride slide when pouring the concrete pad for the ladder section n order to ensure proper placement you will need to set the slide up first to determine where the concrete pillars will be located Figure 20 shows a side view illustration of the or Wild Ride slide foot deck anchor and wedge anchors used in a paver installation Pavers can be a maximum of 3 thick Pavers must be mechanically attached to the concrete pad using a setting material such as mortar or thinset for example that is no thicker than 3 8 1 of each 3 8 x 7 wedge anchor 14 ea needs to be
21. vailable in both right and left turns Check your local electrical code Wild Ride slides available with optional custom powder coated or thermo plastic coated handrails and legs requirements for bonding requirements WRS IM Rev 7 15 SBKINST WRS 15 INSTALLATION MANUAL WILD RIDE SLIDE WILD RIDE SLIDE HARDWARE KITS SH 101 SS STEP AND HANDRAIL ASSEMBLY QTY PART NUMBER COMPONENT DESCRIPTION H SS 1 4 20 X 1 1 4 x 1 hex head bolt s s H SS 1 2 13 BOL 1 9 x 1 172 hex head bolt s s H SS 1 4 H NUT 1 4 finish hex nut s s H SS 1 4 FLAT W 1 4 flat washer s s H SS 1 28 F WAS 1 29 flat washer s s OO COMPONENT DESCRIPTION 7700 oor H SS 1 4X2 1 4H 1 4 x 2 1 4 hex head bolt s s oo H SS 3 8X1 3 4 3 8 x 13 4 hex head bolt 8 5 H SS 1 4 H NUT 1 4 finish hex nut 8 5 mo oOO0 H SS 3 8 F NUT 3 2 finish hex nut s s H SS 1 4 FLAT W 1 4 flat washer s s H SS 3 8 FLT WASHER 3 8 x 1 flat washer s s SH 103 SS STEP TO DECK QTY PART NUMBER COMPONENT DESCRIPTION H SS 3 8X1 HB 3 8 x 1 hex head bolt s s H SS 3 8 F NUT 3 8 finish hex nut s s H SS 3 8 FLT WASHER 3 8 x 1 flat washer s s H SS 3 8 WEDGE 3 8 x 2 3 4 wedge anchor w nut amp flat washer s s O000 000 SH 104 GRAY PROTECTIVE CAPS PART NUMBER COMPONENT DESCRIPTION H 1 WHT CAP gray protective cap 1 2 bolt H 562 X 390 CAP gray protecti
22. ve cap 3 8 bolt nut H 463 X 310 CAP gray protective caps 1 4 bolts nuts SH 106 DECK ANCHOR HARDWARE QTY PART NUMBER COMPONENT DESCRIPTION 55 1 4X2e 1 4H 1 4 x 2 1 4 hex head bolt s s H SS 3 8 WEDGE 3 8 x 2 3 4 wedge anchor w nut amp flat washer s s H 463 X 310 CAP gray protective caps 1 4 bolts H 562 X 390 CAP gray protective cap 3 8 bolt nut 55 1 4 FLAT W 1 4 flat washer s s 55 1 4 H NUT 1 4 finish hex nut s s SH 107 DECK ANCHOR ASSEMBLY QTY PART NUMBER COMPONENT DESCRIPTION SH 106 SH 106 kit WIP WWS DA 9 s s deck anchor SH 108 SLIDE STEP ANCHOR QTY PART NUMBER COMPONENT DESCRIPTION WIP 108 PC Ladder anchor painted H SS 1 4 FL HEA 1 4 x 3 4 socket head cap screw painted H SS 1 4X1 1 4F 1 4 x 1 174 socket head cap screw painted WRS IM Rev 7 15 SBKINST WRS 16 INSTALLATION MANUAL WILD RIDE SLIDE NOTES WRS IM Rev 7 15 SBK INST WRS 17 INSTALLATION MANUAL WILD RIDE SLIDE LIMITED WARRANTY Inter Fab Inc will repair or replace at its option any product manufactured by Inter Fab Inc that fails during the applicable warranty period because of a manufacturing or material defect provided that the defect is not the result of improper installation improper use or care negligence alterations or modifications to the product or natural accidents acts of God The applicable warranty period fo
Download Pdf Manuals
Related Search