38 Series Cordless Phone
Contents
1. Ho USER MANUAL Cover Models e HWD9888 38 TSD S 1 line HWD9888 38 TSD T 2 line Table of Contents 1 Introduction to Bittel 38 Series Cordless Phone 1 1 Unique Features 1 1 2 Main Features 1 2 Installation 2 3 Operation 3 1 Off Hook 3 2 On Hook 3 3 Answer New Call 3 4 Adjust the Call Volume 3 5 Using the Hold Key 3 6 SPKR handset and Wireless Base Handset calling changeable 3 7 Three way conference Two line model only 3 8 To redial the last number dialed 3 9 Mute 3 10 Adjust ringer volume 3 11 Memory keys Only work when outside power is available WwWwwwwh WwW www 1 Introduction to the Bittel 38 Series Cordless Phone This series product is professionally designed and produced for hotels which compile with the standard of indoor digital cordless phone technology requirements According to different frequency standard of each countries can be adjusted to 2 4GHz 1 8 1 9GHz DECT6 0 1 1 Unique Feature gt Auto Registration of the handset to the base Registers the cordless handset to the phone base automatically for any handsets put to the base for power charging gt Both the phone base and cordless handset have speaker functions gt Better sound quality and longer work distance Working distance up to 200 meters in open area gt Dual Channel Conversation function Both of the two line cordless phone can be used simultaneously 1 2 Main Features gt There are one or two2. 20 CONF Button of the handset On hook this button can achieve redial feature and when it s off hook it can be used to adjust the ringer volume 21 FLASH The default is 600ms 22 23 VOL Adjust the volume of the reception when the handset is off hook and the volume of ringer when the handset is on hook 26 DATA Port 27 To Tel port connect the T cable 3 Operation 3 10ff hook a For One line phone pick up the handset or press SPKR of the Base or the handset or press ON key of Handset b For two line model pick up the handset or press SPKR key or the relevant LINE button of the base or handset Note Without outside power if the PBX s current is higher than 35mA the base of one line phone and the LINE 1 of the base of two line phone can work through the Speaker 3 2 On hook a For one line phone put the handset back to the base or press OFF of the handset can finish the call For base it needs press SPKR button b For two line phone put the handset back to the base or press the relevant LINE button can finish the call For the base it needs press the relevant LINE button 3 3 Answer new call a For one line phone pick up the handset or press the SPKR to answer the call for two line phones pick up the handset or press the SPKR or the relevant LINE button b For two line model when there is a new call coming just press the relevant LINE of Handset or Base to answer it When the base handse
3. carefully one by one First please connect the T Cable s power jack Marked 1 in the below figure with the power adaptor Then please connect the T Cable s RJ11 4 pin Marked 2 in the below figure with the telephone line jack in the room Finally please connect the T Cable s RJ11 port 6 pin Marked 3 in the below figure to telephone set s TO TEL port which is on the back of the phone Then install the charge battery into the Handset open the battery cover of Handset and insert the battery plug into the socket Pay more attention to the polarity then put the cover on the battery box When user chooses new battery also need to care the polarity SCHEMAS HWD38TSD S One line J o fo ja aw o l IN ga a 1 Memory keys 2 Charge Indicator 3 Digital keys of the base 4 In USE Indicator Indicator for cordless handset and base off hook state 5 6 VOL Adjust the volume of the reception when the base is off hook and the volume of ringer when the base is on hook 7 22 SPKR speaker key 8 REDIAL Redial the last dialed number which will disappear in five minutes and call the handset when the base is o
4. center 4 4 About Battery a lf the battery hasn t been used for over 5 months after first charging or stored it needs charge last 8 hours for normal use b The new battery must pass 3 4 times charging and using will reach the peak performance c If the device does not use for long time please unplug the battery from the socket and stored in dry environment d If long time no use it will recover after fully charged and discharged for several times e Don t discharge by man made f Please change the battery after using 20 months Suggest to buy from our factory directly Note 1 We won t supply the warranty if the battery are damaged by not charging for long time 2 Please make sure that the batteries are installed before charging 5 Approval 5 1 FCC APPROVAL Complies with Part 68 of the FCC rules On the bottom of this telephone is a label that contains among other information the FCC registration number and the ringer equivalence number REN for this telephone If requested you must provide this information to the Telephone Company 5 2 CE APPROVAL Complies with CE approval 5 3 JACKS Uses RJ11C USOC standard modular jacks 6 Service 6 1 WARRANTY This product is warranted for a period of 12 months from the date of purchase against faulty materials or workmanship If during this period a defect arises we may repair or replace the product at Bittel s discretion provided that 1 The produ
5. ct has not been used for any purpose other than normal use 2 Unauthorized product repair or modifications have not been attempted 3 The product has never been used in a harsh or corrosive environment 4 No damage in transit Page 4 THIS LIMITED WARRANTY GIVES THE BUYER SPECIFIC LEGAL RIGHTS THE BUYER MAY ALSO HAVE OTHER RIGHTS WHICH VARYFROM JURISDICTION TO JURISDICTION This warranty is only valid for merchandise purchased directly from Bittel or dealers or distributors Bittel Co authorized 6 2 FCC WARNING This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 6 3 CUSTOMER SERVICE CENTER Telephone 86 633 2212160 2212103 2212125 Internet www bittelgroup com Email info bittelgroup com Address No 1 Rizhao North Road Rizhao Shandong 276800 China Copyright 2012 Bittel Inc All rights reserved Page 5
6. e nother LINE 3 8 To redial the last number dialed a Base and Handset off hook press REDIAL key for base and one line it s REDIAL button for two line its CONF R button to dial the last number dialed b Default mode After on hook the last dialed number will disappear automatically within five minutes c Setting the Redial to disappear Press HOLD HOLD REDIAL PG d Setting the Redial NOT to disappear Press HOLD HOLD REDIAL PG e Base calls handset on hook press the REDIAL of the base the handset will ring twice Page 3 3 9 Mute Off hook mode press MUTE key to stop the sending re press MUTE remove the mute mode The MUTE indicator of the base will turn on 3 10 Adjust ringer volume On hook press VOL VOL to adjust the ringer volume Note Pressing VOL won t adjust the volume if the reception is set to auto recover 3 11 Memory keys Only work when outside power is available a How to Store On hook mode press HOLD for one line hold indicator will turn and for two line CONF indicator will turn on Desired number twenty four number at most MEMORY key MWL key b How to use The use of the memory keys of the base The handset is in off hook status press the memory key of the base the number will be dialed out The base is in off hook status just need directly press certain memory keys On hook status directly press the memory buttons the base will auto off hook and dial out th
7. e number of the memory key which can be set as followed Base is in on hook status press HOLD Memory key will make the base auto off hook and dial out the number stored in the memory keys c How to delete the stored number in the memory key With outside power press the HOLD Memory keys MWL of the base can delete the stored number 3 12 MWL When there is new message the MWL will flash press MWL key can retrieve the message 3 13 Register and delete the Handset First please connect the outside power and correctly install the battery into the handset then correctly put the handset into the base Please put the handset back to the base when the base in on hook status The charging indicator should be on then off then on After 5 10 seconds please press REDIAL of the base if the handset rings it means the registration succeeds 4 Maintenance and troubleshooting 4 1 No ringing or no continually ringing Check the telephone line Check the quantity of parallel phone set Check the ringer switch position 4 2 Handset doesn t work Press LINE key and the indicator sound Handset not register and need register again The distance is far from Base to Handset back to around Base Power low and need recharge 4 3 Handset not work momentary Poor signal for Handset wait a moment will resume automatically When the device met some trouble don t open by yourself it s better to contact your distributor or local service
8. ill turn off In this case the line will be held e For one line phone re press HOLD then press SPKR of the base of the ON SPKR button of the handset the held line will be released f For two line phone re press the relevant held Line button of the base or the handset the held line will be released If both lines are held then please press the SPKR button of the base or handset to release LINE 1 3 6 SPKR handset and Wireless Base Handset calling changeable a The communication can be changed between speaker status and non speaker status of the handset through the SPKR button on the handset a The communication can be changed between speaker status and non speaker status of the handset through the SPKR button on the handset b Change the communication from base to handset When the base is in use press HOLD button to held the current line then press ON or SPKR button of the handset for one line or press the relevant held LINE for two line then the communication will be changed to the handset and the base will be released when the base is in use directly press the ON or SPKR button of the handset for one line or press the relevant held LINE button for two line the communication will be changed to handset Then please SPKR for one line or relevant LINE for two line to end the communication through the base c Change the communication from handset to base when the handset is in use press HOLD button to h
9. line models The Base and Handset can make answer any calls freely One Base can work with 1 4 Handsets gt Support 2 4GHz 1 8 1 9GHz DECT6 0 standards Adopt HF numerical coding technical between Base and Handsets 3 12 MWL 3 13 Register and delete the Handset RA 4 Maintenance and troubleshooting 4 1 No ringing or no continually ringing 4 2 Handset doesn t work 4 3 Handset not work momentary 4 4 About Battery ARAL 5 Approval 5 1 FCC Approval 5 2 CE Approval 5 3 Jacks RRA 6 Service 5 1 Warranty 5 2 FCC Warranty 5 3 Customer Service Center ans gt Base can answer or dialing calls freely even without outside power For two line phone Line 1 can work normally if th PBX s current is higher than 35mA gt Ringer volume is adjustable gt Data port for connecting modem and fax machine gt Both the base unit and handset ringer volume five steps adjustable gt 10 memory keys stored phone numbers can provide good services for the guests gt Data port Hold Mute gt Both phone base and handset volume four level adjustable gt Default 600ms hook switch flash adjustable and store gt Redials the last number dialed and dialed number disappear within 5 minutes Special configurations optional to store the phone numbers gt Message waiting light compatible with main PBX MWL indicator and withdraw feature Page 1 2 Installation Kindly view the schemas and do following installation
10. n hook 9 19 FLASH The default is 600ms 10 MWL Message waiting Light 12 23 MUTE 13 15 HOLD 14 ON Press it to start turn on the handset 16 Off button press it to turn off the handset 17 Digital keys of the handset 20 21 VOL Adjust the volume of the reception when the handset is off hook and the volume of ringer when the handset is on hook 24 DATA Port 25 To Tel port connect the T cable Page 2 SCHEMAS HWD38TSD T Two line EJ e Alle AEN 1 Memory keys 2 4 VOL Adjust the volume of the reception when the base is off hook and the volume of ringer when the base is on hook 3 Charge Indicator It will light when the handset is charging 5 25 MUTE button 6 In USE Indicator Indicator for cordless handset and base off hook state 7 Redial Redial the last dialed number which will disappear in five minutes and call the handset when the base is on hook 8 24 SPKR 9 CONF Conference button 10 18 LINE 2 11 SPKR Speaker 12 MWL Message waiting Light 13 16 LINE 1 Button 14 17 HOLD 15 Digital button of the base 19 Digital button of the handset
11. old the call then press SPKR of the base for one line or the relevant held line for two line the communication will be changed to base the held line of the handset will be released when the handset is in use then press SPKR of the base for one line or the relevant held line for two line the communication will be changed to handset then please put the handset back to the base or directly press the OFF button of the handset for one line or the relevant held line for two line to end the communication of the handset 3 7 Three way conference Two line model only a Base three way conference Press the accordance line key to connect the call firstly then press HOLD key to hold the current line then connect another line after that press CONF key enter into three way conference mode Press SPKR key to finish the CONF mode b Handset three way conference Press the accordance line key to connect the call firstly then press HOLD key to hold the current line then connect another line after that press CONF key enter into three way conference mode Press accordance line key to finish the CONF mode and keep the current line call or press HOLD key to hold the two lines then press one line key to continue the call c Press the accordance LINE key to remove the CONF mode and enter into the accordance line key talking then press HOLD key to hold the two lines then press the accordance LINE key to talk with the LINE and hold th
12. t is in use the previous call will auto hang up if you press the relevant button of the base handset When the base handset in us use the previous call be held if you press the relevant button of the handset base Note For two line phone the base or the handset can work at the same time if they are using different line in different base or handset 3 4 Adjust the call volume a When Base is in use press VOL key to adjust the receiving volume level of speaker total four levels b When Handset is in use press VOL or VOL to adjust the receiving volume of Handset total 4 levels Note Press HOLD HOLD VOL VOL to recover the default volume level Press HOLD HOLD VOL VOL not to recover the default volume level 3 5 Using the hold key a For one line phone when the base is in use press HOLD button the HOLD indicator will flash IN USE SPkKRindicator will turn off In this case the line will be held b For two line phone when the base is in use press HOLD button the relevant LINE button will flash the IN USE SPKR will turn off In this case the relevant line will be held c For one line phone when the handset is in use press HOLD button of the handset the IN USE SPKR indicator of the base and the ON indicator will turn off In this case the line will be held d For two line phone when the handset is in use press HOLD button of the handset the relevant LINE indicator will flash IN USE SPKR indicator w
Download Pdf Manuals
Related Search