NT600 user manual english free
Contents
1. being tested Read understand and follow all safety messages and instructions in this manual 2 1 Conventions Used We provide safety messages to help prevent personal injury and equipment damage Below are signal words we used to indicate the hazard level in a condition No Signal Word Hazard Level Indicates an imminently hazardous 1 Situation which if not avoided will result ADANGER in death or serious injury to the operator or to bystanders Indicates a potentially hazardous 2 situation which if not avoided could AWARNING result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided may result 3 ACAUTION in moderate or minor injury to the operator or to bystanders 7 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 2 2 Important Safety Instructions And always use your scanner as described in the user s manual and follow all safety messages AWARNING Do not route the test cable in a manner that would interfere with driving controls Awarninc Do not exceed voltage limits between inputs specified in this user s manual AWARNING Always wear ANSI approved goggles to protect your eyes from propelled objects as well as hot or caustic liquids Awarninc Fuel oil vapors hot steam hot toxic exhaust gases acid refrigerant and other debris produced by a malfunction engine can ca2. Information gt Readiness Test 2 View readiness data and use ENTER to save the data EGR Sys FAIL Heated O2 PASS O2 Sensor s FAIL AIC PASS Sec Air Inject PASS EVAP Sys FAIL 5 2 6 Retrieve ECU Information The ECU Information function is used to view ECU information such as ECU part number hardware number and more Some vehicles may not support this function To retrieve ECU information 3 1 Use UP DOWN to select ECU Information from Function Menu screen Read Codes Clear Codes gt ECU Information Readiness Test 2 View ECU information and use ENTER to save the data ECU Information VAG Number 03C906057C NT600 AY Component MT 1 1_ AV JF7K W 5 2 7 Request VIN The VIN function is used to view vehicle identification number Some vehicles may not support this function To request VIN P 1 Use UP DOWN to select VIN from Function Menu screen Read Codes Clear Codes ECU Information gt VIN 2 View VIN information and use ENTER to save the data Vehicle Information Vehicle VIN 1GCEC14W5XZ214506 5 3 Review Data The Review Data function is used to review recorded test results N Depending on vehicle tested the scanner may have different types of data to review To review recorded data P 1 Use UP DOWN to select Review Data from Diagnostic menu 49 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 screen OBDII EOBD Asian Eu
3. Setting To reset the scanner to factory defaults 1 Use UP DOWN to select Default from System Setup screen 2 Press ENTER to confirm Language Contrast Measurement Unit Auto Power off gt Default 3 To reset the scanner to factory defaults use UP DOWN to select YES and press ENTER if the scanner not to set to factory defaults just select NO Are you sure to reset the scan tool to factory defaults NO 4 4Tool Information The Tool Information function is used to view tool information such as software version that may be needed when contacting customer 19 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 service To view tool information 3 1 Use UP DOWN to select Tool Information from Main Menu screen Diagnostics System Setup gt Tool Information 2 Press ENTER to view information Tool Information Serial No xxxxxxxx OS Ver V1 00 H W Ver V1 00 5 Diagnosis 5 1 OBDII EOBD Diagnosis OBDIVEOBD diagnostic menu allows you to e Read DTCs e Clear DTCs e View live datastream e View freeze data e View VM Readiness data e O2 sensor test information e View on board monitor test results e Perform component tests e Retrieve vehicle information e Read modules ID and protocol information e Lookup code definitions 20 NT600 AutoMaster Scanner User s Guide English Version_V1 00 To perform diagnosis on vehicles 3 1 Use UP DOWN to select Diagnostics from Main M
4. engine stopped N If the key is not in the KOEO position use LEFT RIGHT to select NO and return to the Mode Menu screen 3 Answer YES to continue if ECM PCM is to be reset ECM PCM Reset DTCs and freeze data are to be cleared Are you sure to continue YES NO N If ECM PCM is not to be reset answer NO to return 4 Turn the ignition off for 10s and turn it back on to reset the control module Communication The engine should NOT be running but the ignition should be ON Turn the ignition switch off CANCEL N If control module is not to be reset use CANCEL to return 5 When the control module is reset following screen shows 45 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 ECM PCM Reset The ECM has been Cleared Any key to continue N If ECM PCM is not reset make sure the scanner is securely attached to vehicle s DLC and the ignition key is on 5 2 4 View Freeze Data The Freeze Data function is used to view freeze frame data a snapshot of vehicle operating conditions recorded by the on board computer at the time of a fault Some vehicles may not support this function To view freeze frame data P 1 Use UP DOWN to select Freeze Data from Function Menu screen Read Codes Clear Codes gt Freeze Data ECU Information VIN 2 Press ENTER to confirm 3 View freeze frame data on screen If more than one screen of information is available use the LEFT
5. status is e OK vehicle was driven enough to complete the monitor 29 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 e INC Incomplete vehicle was not driven enough to complete the monitor e N A Not Applicable vehicle does not support that monitor N VM Readiness function is performed with the KOER or KOEO N There are two types of I M Readiness tests e Since DTCs Cleared shows status of the monitors since the DTCs were last cleared e This Drive Cycle shows status of monitors since the start of the current drive cycle N Below is a list of abbreviations and names of OBD II monitors supported by the scanner No Abbreviation Name 1 Misfire Monitor Misfire Monitor 2 Fuel System Mon Fuel System Monitor 3 Comp Component Comprehensive Components Monitor 4 Catalyst Mon Catalyst Monitor 5 Hid Catalyst Heated Catalyst Monitor 6 Evap System Mon Evaporative System Monitor 7 Sec Air System Secondary Air System Monitor 8 A C Refrig Mon Air Conditioning Refrigerant Monitor 9 Oxygen Sens Mon Oxygen Sensor Monitor 10 Oxygen Sens Htr Oxygen Sensor Heater Monitor Exhaust Gas Recirculation System 11 EGR System Mon Montor y NOTE Not all monitors are supported by all vehices To retrieve I M Readiness Status data P 1 Use UP DOWN to select I M Readiness from Diagnostic Menu screen Diagnostic Menu Read Codes Clear Codes Datastream F
6. 00 OBDII EOBD Asian gt European USA Review Data 3 Use UP DOWN to select a vehicle manufacturer from the Select Vehicle menu Select Vehicle Volvo gt VW AUDI N For vehicles such as GM and Mercedes you need to observe the menu title to make a series of menu selections to identify vehicle gt 7 2007 6 2006 5 2005 4 2004 3 2003 2 2002 4 When vehicle identified use UP DOWN to select a system to test 40 NT600 AutoMaster Scanner User s Guide English Version_V1 00 gt Engine ABS AT Airbag Instruments N If more than one type of computer modules is detected use UP DOWN to select the module equiped on your vehicle and press ENTER to confirm Engine System p gt 1 6 Cylinder 7 12 Cylinder 5 Wait a few seconds till the scanner establishes communication with the vehicle N If the scanner fails to establish connection with the vehicle make sure the scanner is securely attached to vehicle s DLC and the ignition key is on 5 2 1 Read Codes The Read Codes function is used to read DTCs which are used to help identify the cause of a trouble or troubles with a vehicle N This function can be performed with KOEO or KOER To read DTCs stored in the control module P 1 Use UP DOWN to select Read Codes from Function Menu screen and press ENTER to confirm 41 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 gt Read Codes Clear Codes ECU In
7. 4 3 3 Change Measurement UNI ee ee 17 4 3 4 Change Auto Power Off ee ee 18 4 3 5 Default Setting 2 0 00 ee Re RR ee ee 19 4 4 Tool Information 5 Diagnosis 5 1 OBDIVEOBD Diagnosis ese ee ee ee ee ee ee ee ee ee ee ee 20 5 1 1Read DIES Ee Ee Ee ed EE eg ene ese eg 22 5 41 2 Clear DU CS ress EES werent avers cess 24 5 1 3 Live DatastreaM sees ees ee Re ee ee 25 5 1 4 View Freeze Data sesse ee ee Re ee ee 28 2 NT600 AutoMaster Scanner User s Guide English Version V1 00 5 1 5 Read I M Readiness Status Data 5 1 6 O2 Monitor Test sees ee ee ee 5 1 7 On Board Monitor Test sees esse 5 1 8 Component Test ee 5 1 9 Request Vehicle Information 000 5 1 10 Modules Present seek ee ne 5 1 11 Code LOOKUP iernii ee aada 5 2 Non OBDII Diagnosis esse ee RA ee D2TRead GodeS ii EER ihe elidel 3 2 2 Clear Code EER VEER ees GEED OR Eg 5 2 3 Reset ECM PCM ees ee ee ee ee ee ee ee ee 5 2 4 View Freeze Data sesse esse ee ee ee 5 2 5 Read Readiness Test Data seke 5 2 6 Retrieve ECU Information sesse sees 5 2 7 Request VIN ccccccccseececeeeeeeeeeeeeeeeeeeeeeeaee 5 3 Review Data 6 Update and Print 6 1 Update the Scanner ee ee AA 6 2 Print Data as sii Ed e Be ER DE Ee ER ee nee es 3 NT600 AutoMaster Scanner User s Guide English Version V1 00 1 One Year Limited Warranty Subject to the conditions of this limited w
8. LIGHT RIGHT key to select YES and press ENTER Clear Codes Are you sure to clear codes N If codes and test data not to be deleted select NO and the message Command Cancelled is displayed Wait a few seconds or press any key to return to Diagnostic Menu 4 Wait a few seconds until the message Codes Cleared appears indicating codes are cleared successfully N If the scanner fails to clear the codes the message Clear Error Turn Key on with Engine off is displayed 5 Wait a few seconds or press any key to return to Diagnostic Menu 5 1 3 Live Datastream The Datastream function allows real time viewing of the vehicle s electronic control units PID data including sensor data operation of switches solenoids and relays To view live datastream 1 Use UP DOWN to select Datastream from Diagnostic Menu screen 25 NT600 AutoMaster Scanner User s Guide English Version_V1 00 Read Codes Clear Codes gt Datastream Freeze Data VM Readiness O2 Monitor Test 2 Press ENTER to confirm N If a vehicle does not have this function the message Not Support This Function is displayed View Complete PIDs Complete Data Set displays all supported PIDs of the vehicle being tested To view entire data list 3 1 Use UP DOWN to select Complete Data Set from View Data screen p gt Complete Data Set Custom Data Set 2 Press ENTER to confirm your selection 3 View PIDs on scanner U
9. Link Connector The Data Link Connector DLC is a standard 16 pin interface located under the dashboard on the driver s side of the passenger compartment If the DLC is not located under the dashboard as stated a decal describing its location should be attached to the dashboard in the area the DLC should have been located INOTE On some Asian and European vehicles the DLC is located behind the ashtray which must be removed to access it or on the far left corner of the dash If the DLC cannot be found consult the vehicle s service manual for the location BEHIND ASHTRAY OF DASH 4 1 3 Diagnostic Trouble Codes DTCs Diagnostic Trouble Codes DTCs are faults stored by vehicle computers when problems that affect engine performance and emissions are detected DTCs are used to help identify the cause of a trouble or troubles with a vehicle and determine the fault location s DTCs consist of a five digit alphanumeric code Please see below for the DTCs format and code types 11 NT600 AutoMaster Scanner User s Guide English Version_V1 00 Bx Body Cx Chassis Px Powertrain r EE Ux Network Comm Specific Fault Designation x 0 1 20r3 Vehicle Specific System Example P0101 Mass or Volume Air Flow Circuit Range Performance Problem Powertrain Codes Body Codes POxxx Generic SAE BOxxx Generic SAE Pixxx Manufacturer Specific B1xxx Manufacturer Specific P2xxx Generic SAE B2xxx Man
10. Provides connection between the Connector scanner and vehicle 4 2 4 Specifications No Item Specification Backlit 160 x 105 pixel display with i Display contrast adjustment Es 0 to 60 C 32 to 140T emperature Es 20 to 70 C 4 to 158 F emperature External 4 Power 8 18 Volts powered by vehicle battery 5 Internal Power 9V 6 Dimensions 185mm 85mm 35mm L W H 7 28 3 35 1 38in 7 Weight 1 0Kg 4 3 System Setup System Setup allows you to program the scanner to meet your specific needs e Select system languages e Change measurement unit e Adjust display contrast e Change automatic power off time e Resets the scanner to factory defaults N System Setup settings remain until changes to the existing setups are made 15 NT600 AutoMaster Scanner User s Guide English Version V1 00 To do system setups 1 Use UP DOWN to select System Setup from Main Menu screen Diagnostics p gt System Setup Tool Information 4 3 1 Change Language N The scanner is set to display English menus by default To change system language gt 1 Use UP DOWN to select Language from System Setup screen 2 Press ENTER to confirm p Language Contrast Measurement Unit Auto Power off Default 3 Use UP DOWN to select a language Deutsch Dutch gt English Espanol Francais 4 Press ENTER to save language setting and return 16 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 4 3 2 Adjust Displ
11. RIGHT key DTCFRZF 3 FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT ETC F 172 4 Press 46 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 5 2 5 Read Readiness Test Data The Readiness Test function is used to view a snapshot of the operations for vehicle emission system It is a VW AUDI specific function N The vehicle s computer performs tests on the emission system during normal driving conditions After a specific amount of drive time each monitor has specific driving conditions and time required the computer s monitors decide if the vehicles emission system is working correctly When the monitors status is e Pass vehicle was driven enough to complete the monitor e Fail vehicle was not driven enough to complete the monitor or vehicle does not support that monitor N Readiness Testfunction is performed with the KOER or KOEO N Below is a list of abbreviations and names of monitors No Abbreviation Name Exhaust Gas Recirculation System l EGR Sys Monitor i 2 O2 Sensor s Oxygen Sensor Monitor 3 Catalyst Catalyst Monitor 4 EVAP Sys Evaporative System Monitor 5 Sec Air Inject Secondary Air System Monitor 6 A C Air Conditioning Monitor 7 Catalytic Conv Catalytic Convertor Monitor 8 Heated O2 Oxygen Sensor Heater Monitor To retrieve Readiness test data P 1 Use UP DOWN to select Readiness Test from Function Menu screen Read Codes Clear Codes ECU
12. T600 AutoMaster Scanner User s Guide English Version_V1 00 6 1 Updating the Scanner 2 Connect the scanner to computer with the USB cable supplied and power it on 3 Start the application by selecting Review Data and all records will be loaded to your computer automatically 4 Select a test record to view ala Ml pdate id Review Data dEDA Diagnostic Date Ed vr wy B Record Record1 gt Engine gt ECU Information B Engine VAG Number 630986057 Be BCU Information Component MT 1 61 4U 77KW om 4576 Soft Cding 600071 LMP 896 wse 000000 5 To copy the data to clipboard use the icon Er 6 To edit the data in a text file use the icon 7 If data to be cleared use the icon 8 Click the icon to print the data through computer 53 NT600 AutoMaster Scanner User s Guide English Version V1 00
13. THIRD PARTIES INCLUDING CUSTOMERS AND 5 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 INJURY TO PROPERTY RESULTING FROM THE PURCHASE OR USE OF THE PRODUCT OR ARISING FROM BREACH OF THE WARRANTY BREACH OF CONTRACT NEGLIGENCE STRICT TORT OR ANY OTHER LEGAL OR EQUITABLE THEORY EVEN IF FOXWELL KNEW OF THE LIKELIHOOD OF SUCH DAMAGES FOXWELL SHALL NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE LIMITED WARRANTY OR LOSS OF USE DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED 6 Some states do not allow limitation of how long an implied warranty lasts so the one year warranty limitation may not apply to you the Consumer Some states do not allow the exclusion or limitation of incidental and consequential damages so certain of the above limitations or exclusions may not apply to you the Consumer This limited warranty gives the Consumer specific legal rights and the Consumer may also have other rights which vary from state to state 6 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 2 Safety Information For your safety and to prevent damage to the equipment and vehicles read this manual thoroughly before operating your scanner The safety messages presented below and throughout this users manual are reminders to the operator to exercise extreme care when using this device Always refer to and follow safety messages and test procedures provided by the manufacturer of the vehicle or equipment
14. Trademarks FOXWELL is trademark of Shenzhen Foxwell Technology Co Ltd All other marks are trademarks or registered trademarks of their respective holders Copyright Information 2012 Shenzhen Foxwell Technology Co Ltd All rights reserved Disclaimer The information specifications and illustrations in this manual are based on the latest information available at the time of printing Foxwell reserves the right to make changes at any time without notice Visit our website at www foxwelltech com For Technical Assistance send us email at support foxwelltech com 1 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 Table of Contents 1 One Year Limited Warranty 2 Safety Information 2 1 Conventions Used ee AR RA ee ee ee 7 2 2 Important Safety Instructions 3 Using This Manual 4 Introduction ese EE ge We ke ei EG S 4 1 About OBDIVEOBD 41 1 Whats OBD oo Es EE EG dresses ge aih 10 4 1 2 Data Link Connector ese ke ke neee 11 4 1 3 Diagnostic Trouble Codes DTCS see 11 4 2 About the Scanner eee eee eee ee ee ee ee ke ee 13 4 2 1 Scanner Controls ee ee ee 13 4 2 2 Display Indicators eeren 14 42 3 ACCESSOMES se oi EE GEES RE GESE ESE aes Gede GE ee EERS dee 15 4 2 4 Specifications ee Re Re ee 15 4 3 SYSTEM SetU EG ER EE SES E EG Ga gee R EE SE seek de ie 15 4 3 1 Change Language ee RA ee 16 4 3 2 Adjust Display Contrast ieke ee ee ee 17
15. arranty Shenzhen Foxwell Technology Co Ltd FOXWELL warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of one 1 year In the event this product fails to operate under normal use during the warranty period due to defects in materials and workmanship FOXWELL will at its sole option either repair or replace the product in accordance with the terms and conditions stipulated herein Terms and Conditions 1 If FOXWELL repairs or replaces the product the repaired or replaced product shall be warranted for the remaining time of the original warranty period No charge will be made to the customer for replacement parts or labor charges incurred by FOXWELL in repairing or replacing the defective parts 2 The customer shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable a The product has been subjected to abnormal use abnormal conditions improper storage exposure to moisture or dampness unauthorized modifications unauthorized repair misuse neglect abuse accident alteration improper installation or other acts which are not the fault of FOXWELL including damage caused by shipping b The Product has been damaged from external causes such as collision with an object or from fire flooding sand dirt windstorm lightning earthquake or damage from exposure to weather
16. aulty component or system To request on board monitor test results P 1 Use UP DOWN to select On Board Mon Test from Diagnostic Menu screen Diagnostic Menu gt On Board Mon Test Component Test Vehicle Information Module Present DTC Lookup 2 Use ENTER to confirm 3 Use UP DOWN to pick desired test results 33 NT600 AutoMaster Scanner User s Guide English Version_V1 00 N For non CAN vehicles test screen is illustrated as below On Board Mon Test gt Test 01 Data Test 03 Data Test 05 Data N For CAN vehicles test screen is illustrated as below gt O2 Mon B1S1 O2 Mon B1S2 Catalyst Mon B1 EGR Mon Bank1 N If a vehicle does not have this function the scanner displays a Not Support This Function 4 Use ENTER to view details of selected test results When more than one screen of data is available use LEFT RIGHT N For non CAN vehicles test screen is illustrated as below Test 01 Data N For CAN vehicles test screen is illustrated as below 34 NT600 AutoMaster Scanner User s Guide English Version_V1 00 O2 Mon B1S1 Rich Lean Threshd mV MEAS 0 450 0 312 0 630 OK 5 Press the BACK key to return to On Board Mon Test 5 1 8 Component Test The Component Test allows the scanner to control operation of vehicle components tests or systems N Some manufacturers do not allow tools to control vehicle systems N The manufacturer sets the crit
17. ay Contrast To adjust display brightness 1 Use UP DOWN to select Contrast from System Setup screen 2 Press ENTER to confirm Language Contrast Measurement Unit Auto Power off Default 3 Use the LEFT RIGHT key to adjust contrast j Use LEFT or RIGHT to adjust brightness 4 Press ENTER to save contrast setting and return 4 3 3 Change Measurement Unit N Metric is the default measurement unit To change measurement unit 1 Use UP DOWN to select Measurement Unit from System Setup screen 2 Press ENTER to confirm Language Contrast gt Measurement Unit Auto Power off Default 17 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 3 Use UP DOWN to select a measurement unit p English Metric 4 Press ENTER to save measurement setting and return 4 3 4 Change Auto Power Off N The minimum auto power off time is 1 minute and the maximum is 30 minutes N The Auto Power Offfunction is available only when the scanner is powered by internal battery To change automatic power off time P 1 Use UP DOWN to select Auto Power Off from System Setup screen 2 Press ENTER to confirm Language Contrast Measurement Unit b Auto Power off Default 3 Use UP DOWN to increase or decrease time 18 NT600 AutoMaster Scanner User s Guide English Version_V1 00 01 Minute UP Increase time DOWN Decrease time ENTER Confirm 4 Use ENTER to save 4 3 5 Default
18. cle operating conditions recorded by the on board computer at the time of an emission related fault N If codes were cleared freeze data may not be stored in vehicle memory depending on vehicle To view freeze frame data 1 Use UP DOWN to select Freeze Data from Diagnostic Menu screen 28 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 Diagnostic Menu Read Codes Clear Codes Datastream gt Freeze Data VM Readiness O2 Monitor Test 2 Press ENTER to confirm 3 View freeze frame data on screen DTCFRZF 3 FUELSYS1 OL Drive FUELSYST2 SHRTFT1 N If more than one screen of information is available use the LEFT RIGHT key N If no freeze frame detected the message No Freeze Data Found is displayed N If a vehicle does not have this function the message Not Support This Function is displayed 4 Press the BACK key to return to Diagnostic Menu 5 1 5 Read I M Readiness Status Data The M Readiness function is used to view a snapshot of the operations for the emission system on OBDII EOBD vehicles N VM Readiness is a useful function used to check if all monitors are OK or N A N The vehicle s computer performs tests on the emission system during normal driving conditions After a specific amount of drive time each monitor has specific driving conditions and time required the computer s monitors decide if the vehicles emission system is working correctly When the monitors
19. conditions an Act of God or battery leakage theft blown fuse improper use of any electrical source or the product was used in combination or connection with other product attachments supplies or consumables not manufactured or distributed by FOXWELL 3 The customer shall bear the cost of shipping the product to FOXWELL And FOXWELL shall bear the cost of shipping the product back to the customer after the completion of service under this limited warranty 4 FOXWELL does not warrant uninterrupted or error free operation of the product If a problem develops during the limited warranty period the consumer shall take the following step by step procedure 4 NT600 AutoMaster Scanner User s Guide English Version_V1 00 a The customer shall return the product to the place of purchase for repair or replacement processing contact your local FOXWELL distributor or visit our website www foxwelltech com to get further information b The customer shall include a return address daytime phone number and or fax number complete description of the problem and original invoice specifying date of purchase and serial number c The customer will be billed for any parts or labor charges not covered by this limited warranty d FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product If FOXWELL cannot perform repairs covered under this limited warranty within 30 days or after a reasonable number o
20. e examples only and actual test screen may vary for each vehicle being tested Example Diagnostics p System Setup Tool Information Arrow Icon P An arrow icon indicates a procedure Example To change menu language P 1 Use UP DOWN to select Language from System Setup screen 2 Press ENTER to confirm 4 Introduction NT600 is a multifunctional scan tool delicately designed for DIYers pros and enthusiasts to pinpoint engine transmission ABS and airbag faults 4 1 About OBDIVEOBD 4 1 1 What is OBD The first generation of On Board Diagnostics or OBD was introduced in early 1980 s to control engine functions and diagnose engine problems by vehicle manufacturers As the OBDI lacked standardization of protocols and interface it allowed different interpretations among vehicle manufacturers OBDII the second generation On Board Diagnostics improved in both capability and standardization is a system developed in mid 1990 s by the Society Automotive Engineers SAE to standardize automotive 10 NT600 AutoMaster Scanner User s Guide English Version_V1 00 electronic diagnosis EOBD is European version of OBDII required in Europe since2001 The OBDII standard specifies e A generic diagnostic port Data Link Connector and its pinout e The protocols and the messaging format e A standard list of vehicle parameters identifications e A standard list of diagnostic trouble codes DTCs 4 1 2 Data
21. e to be cleared Are you sure to continue YES NO N If test data are not to be deleted answer NO to return N On Honda vehicles you are asked to turn the ignition off for 10s and turn it back on to proceed to erase codes 43 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 Communication The engine should NOT be running but the ignition should be ON Turn the ignition switch off CANCEL N If codes and freeze data are not to be erased turn ignition off and then back on 10s later as instructed if they are not to be deleted use CANCEL to return 4 Use the Read Codes function to verify if codes are cleared N If codes are not cleared make sure the scanner is securely attached to vehicle s DLC and the ignition key is on 5 2 3 Reset ECM PCM The ECM PCM Reset is a Honda specific function It allows the scanner to delete DTCs freeze data and manufacturer enhanced data from vehicle s on board computer module N Perform this function only after systems have been checked completely N This function is performed with KOEO Do not start the engine To reset the engine powertrain control module gt 1 Use UP DOWN to select ECM PCM Reset from Function Menu screen and press ENTER to confirm Read Codes Clear Codes gt ECM PCM Reset 2 Answer YES to continue if the key is in the KOEO position 44 NT600 AutoMaster Scanner User s Guide English Version_V1 00 ECM PCM Reset Ignition on and
22. ehicle Information from Diagnostic Menu screen Diagnostic Menu On Board Mon Test Component Test gt Vehicle Information Module Present DTC Lookup 36 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 2 Press ENTER to confirm 3 Observe on screen instruction and wait a few seconds or press any key to continue Vehicle Information Turn key on with engine off Any key to continue N If a vehicle does not have this function the message Not Support This Function is displayed 4 Press ENTER to confirm 5 Use UP DOWN to select an available item from Vehicle nformation screen Vehicle Information gt Calibration ID 6 Press ENTER to view test information Calibration ID Cal ID 06A906032SD 6462 7 Press ENTER return NOTE Information can be requested may be different depending on vehicle tested 37 NT600 AutoMaster Scanner User s Guide English Version_V1 00 5 1 10 Modules Present The scanner identifies module IDs and communication protocols for OBD2 modules in the vehicle To view module IDs and communication types 1 Use UP DOWN to select Modules Present from Diagnostic Menu screen Diagnostic Menu On Board Mon Test Component Test Vehicle Information gt Module Present DTC Lookup 2 Press ENTER to view information Modules Present ID Protocol 10 ISO 9141 2 1A ISO 9141 2 5 1 11 Code Lookup This function is used to reque
23. enu screen gt Diagnostics System Setup Tool Information 2 Use UP DOWN to select OBDII EOBD from Diagnostic menu screen and press ENTER to confirm gt OBDIVEOBD Asian European USA Review Data N The scanner detects the communication protocol when it is connected to the vehicle and uses the protocol throughout the testing till another vehicle is diagnosed N If the scanner fails to communicate with the vehicle the message Communication Error is displays Make sure the OBDII connector is securely attached and the ignition key is on Turn vehicle key to off for 10 seconds then on N When the scanner links to vehicle it checks the status of I M Monitors and gives a summary report on the display as illustrated below MIL Status O Code Found Monitors N A Monitors OK NT600 A Monitors INC Any key to continue MELT N If vehicle is equipped with more than one computer module for example a powertrain control module PCM and a transmission control module TCM the scanner identifies them by their identification names ID assigned by manufacturer i e Engine or Module A4 Control Module gt Engine AIT 5 1 1 Read DTCs The Read Codes function is used to read DTCs stored codes which are used to help identify the cause of a trouble or troubles with a vehicle and pending codes from the vehicle s control modules N When emission related or drivability fault occurs the control module il
24. eria to automatically stop test Refer to appropriate vehicle service manual before using this function To do component test P 1 Use UP DOWN to select Component Test from Diagnostic Menu screen On Board Mon Test gt Component Test Vehicle Information Module Present DTC Lookup 2 Press ENTER to confirm 3 Use UP DOWN to pick an available system or component 35 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 Component Test gt Evap Leak Test 4 Press ENTER to start testing and the scanner displays the message Command Sent N If a vehicle does not have this function the scanner displays the prompt Not Support This Function 5 Press the BACK key to return to Diagnostic Menu 5 1 9 Request Vehicle Information The Vehicle Information function is used to request the vehicle s VIN number calibration ID s which identifies software version in vehicle control module s calibration verification numbers CVN s and in use performance tracking on model year 2000 and newer OBD II compliant vehicles VN CVNs are calculated values required by OBD II regulations They are reported to check if emission related calibrations have been changed Multiple CVNs may be reported for a control module It may take several minutes to do the CVN calculation N In use performance tracking tracks performance of key readiness monitors To request vehicle information P 1 Use UP DOWN to select V
25. f attempts to repair the same defect FOXWELL at its option will provide a replacement product or refund the purchase price of the product less a reasonable amount for usage e If the product is returned during the limited warranty period but the problem with the product is not covered under the terms and conditions of this limited warranty the customer will be notified and given an estimate of the charges the customer must pay to have the product repaired with all shipping charges billed to the customer If the estimate is refused the product will be returned freight collect If the product is returned after the expiration of the limited warranty period FOXWELL normal service policies shall apply and the customer will be responsible for all shipping charges 5 ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE SHALL BE LIMITED TO THE DURATION OF THE FOREGOING LIMITED WRITTEN WARRANTY OTHERWISE THE FOREGOING LIMITED WARRANTY IS THE CONSUMER S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED FOXWELL SHALL NOT BE LIABLE FOR SPECIAL INCIDENTAL PUNITIVE OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF ANTICIPATED BENEFITS OR PROFITS LOSS OF SAVINGS OR REVENUE LOSS OF DATA PUNITIVE DAMAGES LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT COST OF CAPITAL COST OF ANY SUBSTITUTE EQUIPMENT OR FACILITIES DOWNTIME THE CLAIMS OF ANY
26. following screen shows 23 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 Memory space is full Overwrite previous recording and save data from this test N To empty the memory space use LIGHT RIGHT to select YES otherwise select NO and press ENTER to quit NOTE Whenever you wish to save test results just press ENTER when viewing them 6 Use the BACK key to exit 5 1 2 Clear DTCs The Clear Codes function is used to delete DTCs and I M Readiness data from vehicle s control module s It may also erase freeze data and set monitors to incomplete or not ready N Perform Clear Codes function only after systems have been checked completely N After servicing the vehicle erase stored DTCs and verify no codes have been reset If a DTC returns problem has not been fixed or other faults are present N Depending on which monitor sets a code the vehicle may need to be driven and the monitor ran before concluding that the fault is repaired N This function is performed with KOEO Do not start the engine To erase codes from vehicle control modules O 1 Use UP DOWN to select Clear Codes from Diagnostic Menu screen 24 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 Diagnostic Menu Read Codes gt Clear Codes Datastream Freeze Data VM Readiness O2 Monitor Test 2 Press ENTER to confirm 3 If codes and diagnostic results are to be cleared use the
27. formation Readiness Test 2 View code definitions on screen use UP DOWN to view additional information and use LEFT RIGHT to scroll back and forth through different codes 00400 Signal Acoustic Return Message Sporadic 001 upper Limit exceeded N If no codes detected in the control module the message System pass No fault found appears 3 Use ENTER to save code definitions 5 2 2 Clear Codes The Clear Codes function is used to delete DTCs freeze data and manufacturer enhanced data from vehicles on board computer module N Perform Clear Codes function only after systems have been checked completely N After servicing the vehicle erase stored DTCs and verify no codes have been reset If a DTC returns problem has not been fixed or other faults are present N This function is performed with KOEO Do not start the engine To clear DTCs stored in the control module 1 Use UP DOWN to select Clear Codes from Function Menu screen and press ENTER to confirm 42 NT600 AutoMaster Scanner User s Guide English Version_V1 00 Read Codes gt Clear Codes ECU Information Readiness Test 2 Answer YES to continue if the key is in the KOEO position Clear Codes Ignition on and engine stopped N If the key is not in the KOEO position use LEFT RIGHT to select NO and return to the Mode Menu screen 3 Answer YES to continue if codes are to be cleared Clear Codes DTCs and freeze data ar
28. his function is not supported by vehicle Refer to On Board Monitor Tests on page 34 35 for O2 monitor data of CAN equipped vehicles To retrieve O2 monitor data P 1 Use UP DOWN to select O2 Monitor Test from Diagnostic Menu screen Diagnostic Menu Read Codes Clear Codes Datastream Freeze Data VM Readiness p gt O2 Monitor Test 2 Press ENTER to confirm 3 Use UP DOWN to pick a O2 sensor O2 Monitor Test gt O2 Bank1 Sensor1 O2 Bank1 Sensor2 N If a vehicle does not have this function the scanner displays the message Not Support This Function 32 NT600 AutoMaster Scanner User s Guide English Version_V1 00 4 Press ENTER to view data of selection O2 Bank1 Sensor1 81 Values MOD 10 126 90 255 N When more than one screen of data is available use the LEFT RIGHT key 5 Press the BACK key to return to O2 Monitor Test screen 5 1 7 On Board Monitor Test The On Board Monitor Test function is useful after servicing or after clearing a vehicle ECU s memory It receives test results for emission related powertrain components and systems that are not continuously monitored for Non CAN vehicles And for CAN vehicles it receives test data for emission related powertrain components and systems that are and are not continuously monitored It is vehicle manufacturer who is responsible for assigning test and component IDs NOTE Test results do not necessarily indicate a f
29. king up DTCs Scrolls back and forth through codes found and through different screens of data Also it is used to cancel all selections of PIDs when viewing custom PID list G ENTER Key confirms an action or movement and goes to next level and saves test data H BACK Key cancels an action and returns to previous screen or level HELP Key accesses to the Help function J Power Switch Turns on off the scanner to the update tool FoxLink pro to do upgrades and reboots the scanner when powered by vehicle battery IMPORTANT Do not use solvents such as alcohol to clean keypad or display Use a mild nonabrasive detergent and a soft cotton cloth IMPORTANT Do not soak keypad as water might find its way into the scanner 4 2 2 Display Indicators Below is a list indictors used to help navigate through menus No Indicator Description 1 Indicates the control module number 2 Indicates more than one screen of information is available 14 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 4 2 3 Accessories No Part Description Provides operation instructions for the 1 Users Manual usage of the scanner Provides connection between the scanner and a computer to update 2 USB Cable programs and DTCs and to load test data to the computer 3 Connection Connects the scanner with diagnostic Cable connector 4 Diagnostic
30. luminates the malfunction indicator lamp MIL N Pending Codes are also referred to as continuous monitor or maturing codes that indicate intermittent faults If the fault does not occur within a certain number of drive cycles depending on vehicle the code clears from memory If fault occurs a specific number of times the code matures into a DTC and the MIL illuminates or blinks N This function can be performed with KOEO or KOER To read codes from vehicle control modules gt 1 Use UP DOWN to select Read Codes from Diagnostic menu screen 22 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 Diagnostic Menu P gt Read Codes Clear Codes Datastream Freeze Data VM Readiness O2 Monitor Test 2 Press ENTER to confirm 3 View DTCs and their definitions P0101 10 Mass or Volume Air Flow A Circuit Range Performance N If no DTCs are present the message No Pending Codes Found is displayed N If any manufacturer specific or enhanced codes detected select vehicle a make before viewing DTC information N If manufacturer of the vehicle being tested is not list select Other 4 Use the UP DPWN key to move to next screen when the code has more than one screen information Use LEFT RIGHT to move back and forth through codes when more than one code is detected 5 To save the fault data press ENTER and the message Data Saved is displayed N If there is not enough memory space
31. r e RAM 64MB or better e Hard Disk Space 30MB or better e Display 800 600 pixel 16 byte true color display or better e Internet Explorer 4 0 or newer IMPORTANT Do not disconnect the scanner from computer or power off the computer during the process of updating To update the scanner P 1 Download the update tool FoxLink Pro and update files from 51 NT600 AutoMaster Scanner User s Guide English Version_V1 00 our site www foxwelltech com by selecting Home gt Updates gt NT600 and save the applications and update file in computer disk 2 Unzip the update tool file Follow instructions on computer screen to install the tool and driver Double click the desktop icon to launch the application Connect the scanner to computer with the USB cable provided Turn on the scanner by pressing the power button Start the update application by selecting Update Use Select file to locate update file downloaded co NOOO HE Click Update to start updating Update Review Data Step 1 Connect the device to computer Step 2 Press the power button of the device to connect it with the software Step 3 Click lt Select File gt to locate update file Step 4 Click lt Update gt to start Select file Connect the device to computer 6 2 Print Data All test results are able to be printed through computer To print test results gt 1 Download and launch FoxLink Pro as instructed on page 51 of 52 N
32. reeze Data gt I M Readiness O2 Monitor Test 30 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 2 Press ENTER to confirm N If vehicle supports both types of monitors following screen displays I M Readiness gt Since DTCs Cleared This Drive Cycle N Use UP DOWN to select a monitor type and press ENTER to confirm 3 Depending on readiness test one of these 2 screens will be present Since DTCs Cleared MIL Status Misfire Monitor Fuel System Mon Comp Component Catalyst Mon Htd Catalyst This Drive Cycle MIL Status Misfire Monitor Fuel System Mon Comp Component Catalyst Mon Htd Catalyst N If more than one screen of information is available use the LEFT RIGHT key N If a vehicle does not have this function the message Not Support This Function is displayed 31 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 4 Press the BACK key to return to Diagnostic Menu 5 1 6 O2 Monitor Test OBD II regulations require certain vehicles monitor and test oxygen 02 sensors to isolate fuel and emissions related faults The O2 Monitor Test function is used to retrieve completed O2 sensors monitor test results N The O2 Monitor Test is not an on demand test O2 sensors are not tested when selected via the menu but tested when engine operating conditions are within specified limits N If the vehicle uses a controller area network CAN protocol to communicate t
33. ropean USA gt Review Data 2 Press ENTER to confirm 3 Use UP DOWN to select a vehicle and press ENTER Select Vehicle gt Ford EOBD Delete all data N If no data is recorded the message No Data available is displayed 4 Observe the menu title to make selection till recorded data are identified and view the test records P0101 10 Exhaust Gas Recirculation Sensor A Circuit Low N Record x indicates how many tests you have performed and Test x indicates how many times you have recorded from the same test 50 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 5 If all test records of test are to be cleared use UP DOWN to select Delete all data Select Vehicle Ford EOBD gt Delete all data 6 Use LEFT RIGHT to select YES to delete all records or select NO to cancel 6 Update and Print The scanner is able to be updated to keep you stay current with the latest development of diagnosis Also it allows you to upload recorded test results to your PC or laptop for analysis and printing 6 1 Update the Scanner N To update the scanner you need following tools e NT600 scanner e Update Tool FoxLink Pro e PC or laptop with USB ports and Internet explorer e USB cable N To be able to use update tool PC or laptop must meet the following minimum requirements e Operation System Win98 NT Win ME Win2000 Win XP VISTA and Windows 7 e CPU Intel PIII or bette
34. se the LEFT key when more than one screen of information is available DTC_CNT 3 FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT 0 0 ETC F SHRTFT1 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 4 Use the RIGHT key to view PID graph EES PET 4505 we 5 Use ENTER to save data Recording DTC_CNT 3 FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT ETC F 172 SHRTFT1 0 0 N The scanner stops saving live data once the memory space is full or the BACK key is pressed 6 Press the BACK key to return to previous level View a Customized List of PIDs Custom Data Set allows certain PIDs from Complete Data Set to be selected To view custom data list gt 1 Use UP DOWN to select Custom Data List from View Data screen Complete Data Set gt Custom Data Set 27 NT600 AutoMaster Scanner User s Guide English Version_V1 00 2 Press ENTER 3 Use UP DOWN to move up or down and press the RIGHT key to select or deselect PIDs to view To cancel all your selection use the LEFT key Selected parameters are marked with solid squares LIDTC_CNT E FUELSYS1 01 N FUELSYST2 02 N LOAD PCT 03 ETC F 04 E SHRTFT1 05 4 Press ENTER to view selected PIDs DTC_CNT 3 FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT 0 0 ETC F 172 SHRTFT1 0 0 5 Use the BACK key to return 5 1 4 View Freeze Data The Freeze Data function is used to view freeze frame data a snapshot of vehi
35. st DTC definitions stored in the scanner To look up DTCs 1 Use UP DOWN to select Code Lookup from Main Menu screen Diagnostic Menu On Board Mon Test Component Test Vehicle Information Module Present gt Code Lookup 38 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 2 Use ENTER to confirm 3 Use the LEFT RIGNT key to change highlighted character use the UP DOWN button to change value Code Lookup P0001 UP DOWN button to change value LEFT RIGHT button to change character 4 Press ENTER to view the DTC definition Use the LEFT RIGHT key to scroll back and forth through DTCs N If definition could not be found SAE or Manufacturer Specific the scanner displays DTC definition not found Please refer to vehicle service manual N For manufacturer specific codes select a vehicle make to look for DTC definitions 5 To quit Code Lookup press the BACK key 5 2 Non OBDII Diagnosis Non OBDII diagnosis function of this scanner is used to read and clear engine transmission ABS and airbag codes and view ECU information on major Asian American and European vehicles To perform diagnosis on vehicles P 1 Use UP DOWN to select Diagnostics from Main Menu screen gt Diagnostics System Setup Tool Information 2 Use UP DOWN to select a market area from Diagnostic menu screen and press ENTER to confirm 39 NT600 AutoMaster Scanner User s Guide English Version_V1
36. st of conventions we used in the manual Safety Information See Safety Information on page 8 Bold Text Bold emphasis is used in procedures to highlight selectable items such as buttons and menu options Example Use UP DOWN to select the desired measurement unit Bold ltalic Text Bold italic text is used in the procedures to highlight the menus on the scanner screen Example Use UP DOWN to select Language from System Setup screen Symbols and Icons V Check Note Additional information about the subject in the preceding paragraph is introduced by a N Check Note Example N The scanner is set to display English menus by default e Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot e Example System Setup allows you to e Select menu languages e Change measurement unit e Adjust display contrast IMPORTAN IMPORTANT indicates a situation which if not avoided may result in damage to the test equipment or vehicle Example IMPORTANT Do not soak keypad as water might find its way into the scanner NOTE NOTE provides helpful information such as additional explanations 9 NT600 AutoMaster Scanner User s Guide English Version V1 00 tips and comments Example NOTE Not all data are supported by all vehicles Screens Some help messages information and data displayed on the scanner are also shown in graphical text boxes The screens presented ar
37. ufacturer Specific P30xx P33xx Manufacturer Specific B3xxx Generic SAE tipi PIN Generic SAE Network Communication Codes Chassis Codes UOxxx Generic SAE COxxx Generic SAE Utxxx Manufacturer Specific C1xxx Manufacturer Specific U2xxx Manufacturer Specific C2xxx Manufacturer Specific U3xxx Generic SAE C3xxx Generic SAE 12 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 4 2 About the Scanner 4 2 1 Scanner Controls A B H C E F D J A Diagnostic Port provides communication for vehicle DLC B LCD Display shows menus test results and operation tips C UP Key moves selection up When a DTC has more than one screen of information moves up through the current screen to previous screens for additional data When looking up DTC it is used to change value of selected character D DOWN Key moves selection down When a DTC has more than one screen of information moves down through the current screen 13 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 to next screens for additional data When looking up DTC it is used to change value of selected character E LEFT SCROLL KEY goes to previous character when looking up DTCs Scrolls back and forth through codes found and through different screens of data Also it is used to make selection of PIDs when viewing custom PID list and to view PID graphs F RIGHT SCROLL KEY goes to next character when loo
38. use serious injury or death Do not use the scanner in areas where explosive vapor may collect such as in below ground pits confined areas or areas that are less than 18 inches 45 cm above the floor AWARNING Do not smoke strike a match or cause a spark near the vehicle while testing and keep all sparks heated items and open flames away from the battery and fuel fuel vapors as they are highly flammable AWARNING Keep a dry chemical fire extinguisher suitable for gasoline chemical and electrical fires in work area Awarninc Always be aware of rotating parts that move at high speed when an engine is running and keep a safe distance from these parts as well as other potentially moving objects to avoid serious injury Awarninc Do not touch engine components that get very hot when an engine is running to avoid severe burns AWARNING Block drive wheels before testing with engine running Put the transmission in park for automatic transmission or neutral for manual transmission And never leave a running engine unattended Awarninc Do not wear jewelry or loose fitting clothing when working on engine AcauTion Make sure to turn off ignition before connecting or disconnecting the scanner 8 NT600 AutoMaster Scanner User s Guide_English Version_V1 00 3 Using This Manual We provide instructions for the usage of your scanner in this manual Below is a li
Download Pdf Manuals
Related Search