AL003 User Manual - Factory Direct Medical
Contents
1. subjected to excessive loads imposed by rough driving Caution Do not enter steep driveways straight on Enter and leave at an angle to the street so that your Tilt and Tote platform does not drag on the ground Caution Do not attempt to move the vehicle with the Tilt and Tote platform in the down position If moved this way the lifting mechanism will be damaged MAINTENANCE Every 30 days oil the pivot points on all moving parts Check for paint chips and touch up any bare metal with a good gloss black enamel or lacquer to inhibit rust This may be necessary more frequently when subjected to salt air or road salt Troubleshooting Guide Problem Possible Cause Suggestions Hold down will not stay upright or Improper adjustment at pivot Tighten or loosen bolts until hold down arm or is difficult to move points platform operates smoothly with some resistance Lift platform is difficult to move The Red T Handle is hard to pull Lack of lubrication A lubricating spray WD 40 will loosen the linkage to the platform latch Lift up slightly on the platform to release pressure on the release latch The lift does not reach the ground Hitch adapter positioning or Check the connection of the hitch adapter to the when completely lowered incorrect hitch adapter hitch post Normal range of operation is 5 19 inches measured from the bottom of the hitch to the ground Higher vehicles require special hitch Lift bottoms out while enteri2. 2 S lt rlsatt installation and Owner Manual MOBILITY ALO003 Tilt N Tote A Read manual thoroughly before attempting to install or operate lift This manual has been provided to assist Dealer you with lift installation and operation For further assistance please contact you authorized Harmar Mobility dealer or Harmar s Technical Services department Tel 800 833 0478 Fax 866 234 0478 Email tech harmar com Serial Number Unpacking the Lift CARRIER ASSEMBLY STABILIZER OPTIONAL OPTIONAL CLASS 2 CLASS 3 Each Tilt and Tote is packaged with a Class 1 Hitch Adapter and Stabilizer If a Class 2 or Class 3 hitch adapter is required separate parts must be ordered Be sure and check the contents of the box against the package check list to be sure that all parts are included with the carrier that are required for proper installation If any parts are missing or if any damage is noted immediately contact the distributor from which you purchased your lift DO NOT attempt to install or use the lift with any missing or damaged parts Hitch Adapter Installation CLASS 1 CLASS 3 Bumper Mount Flat Bar Style 2x2 TUBE Be sure to comply with vehicle s bumper rating Refer to diagram below for proper orientatio
3. G SMALLER FRONT WHEELS OFF THE GROUND ROLL WHEELCHAIR OFF PLATFORM PUSH DOWN ON FRONT OF PLATFORM OR PULL UP ON YELLOW HANDLE TO ROTATE PLATFORM LEVEL PULL ON RED HANDLE GRAVITY WILL TILT THE PLATFORM TO THE GROUND TO RELEASE PRESSURE OFF LATCHING MECHANISM FOLD THE HOLD DOWN ARM BACK DOWN lt gt PULLUP ON RED AND PLACE KEEPER SLOT HANDLE b ONTO LOCKING TAB ROTATE z S U PLATFORM UPRIGHT PLATFORM WILL AUTOMATICALLY LATCH IN PLACE Safety Maintenance amp Troubleshooting SAFETY Caution Keep hands away from PINCH POINTS Inspect the condition of your Tilt and Tote often If any parts are worn or damaged DO NOT USE THE TILT and TOTE Immediately contact your Harmar Mobility Authorized Dealer Caution Keep hands feet and any other objects away from the platform as it lowers Caution Some chairs have pneumatic air inflated tires If your chair has this type tire be sure the tires are properly inflated Improper inflation of the tires will affect how the unit fits on the platform and therefore change the amount of clamping force on the chair Caution Before driving off with your chair or scooter on the Tilt and Tote make sure that the chair is firmly held down on the platform Caution When driving with your chair on the Tilt and Tote slow down for potholes speed bumps railroad tracks etc Your Tilt and Tote could be damaged by abuse if
4. eature P REMOVE HITCH PIN ONCE PIN IS REMOVED THE y WHILE BRACING TILT AND TOTE CAN BE LOWERED dc TILT AND TOTE JUST BELOW PARALELL WITH THE UPRIGHT GROUND BEFORE RESTING ON ITS MECHANICAL STOPS TO ERECT THE TILT AND TOTE BACK TO ITS TRAVEL POSITION SIMPLY ROTATE UPRIGHT AND REPLACE THE HITCH PIN NEVER ATTEMPT TO TRANSPORT WITH THE TILT AND TOTE IN THE FOLDED DOWN POSITION FF X o O PULL UP ON RED HANDLE lt FLIP THE HOLD DOWNARM UPRIGHT ONCE LARGER WHEELS ARE SEATED IN THE PLATFORM CRADDLE PULL UP ONTO WHEELCHAIR HANDLES ONCE LEVEL PLATFORM CRADDLE Loading Wheelchair ROTATE PLATFORM DOWN WITH YELLOW HANDLE CONTINUE TO PULL ON RED HANDLE PUSH DOWN ON WHEELCHAIR HANDLES TILTING SMALLER FRONT WHEELS OFF THE GROUND ROLL WHEELCHAIR ONTO PLATFORM TILT PLATFORM TO THE GROUND CINCH HOLD DOWN ARM TIGHT AGAINST WHEELCHAIRS ARMREST BY TURNING RED HANDLE CLOCKWISE YOUR WHEELCHAIR IS NOW READY FOR TRANSPORT Unloading Wheelchair RELEASE PRESSURE OFF HOLD DOWN ARM BY TURNING RED HANDLE COUNTER CLOCKWISE PUSH DOWN ON WHEELCHAIR HANDLES TILTIN
5. n right side up or upside down Determines carrier s height from the ground d CLASS 2 1 25 x 1 25 Solid Bar Do not attempt to mount up from under DETERMINE BEST MOUNTING HEIGHT Harmar recommends maintaining 8 12 of ground clearance from the bottom of the unfolded platform while not exceeding 45 degrees of tilt 12 off the ground To achieve this a number of mounting options are available REMOVE REMOVE MOVE UP FLIP FLIP MOVE UP AS SHIPPED RE ATTACH m RE ATTACH RE ATTACH d A ae Measure from Hitch Bar to ground il y Zi li v ORIENTATION OF CLASS 2 and CLASS 3 HITCH ADAPTERS IS IDENTICAL SS 8 1 NOTE L IF FLIPPING HITCH ADAPTER FOR BETTER HEIGHT OR P BOTH PARTS MUST BE FLIPPED TOGETHER ORIENTATION OF THESE PARTS IS IMPORTANT FOR THE TILT AWAY FEATURE LIMITS Hold Down Arm Installation HOLD DOWN ARM HEIGHT CAN BE ADJUSTED SO THAT WHEELCHAIR s P ARMRESTS CLEAR ARM WHEN LOAD Hon ES ING ONTO A TILTED PLATFORM ARM EN WHEN PLATFORM IS TILTED UPRIGHT DESIRED HEIGHT THE ARMRESTS SHOULD BARELY CON TACT THE BOTTOM OF THE ARM TIGHTEN SET THE RED KNOB CAN THEN BE TURNED TO HOLD THE WHEELCHAIR DOWN TIGHT SCREWS Tilt Away F
6. ng adapters which can be obtained from a Harmar driveways or going over bumps Mobility Authorized Dealer Lift should be installed at the highest adjustment point possible 30 1035 HHCS A2 43x275 4 243 Nyoc Nut Bollo Washer 1 2 ID CAP for 1x1 Tubs CAP for 1x2 Tube 10 32 x 25 winter tooth wash HOLD DOWN INNER ARM MWC SAFETY PIN 1 2 da x 3 MIDDLE ASSEMBLY 38 18 x3 00 10 13 x 225 386 16 x 1 2 allen head Socket Head Cap 14 20 x 58 BEARING THRUST Snap In 38 D AL003 Tilt N Tote WARNING YOU MUST HAND WASH OR USE A TOUCHLESS AUTOMATIC CAR WASH TO PREVENT LIFT DAMAGE IF YOU HAVE ANY QUESTIONS REGARDING WASHING A CAR EQUIPPED WITH A HARMAR LIFT PLEASE CALL THE HARMAR TECHNINCAL SERVICES DEPARTMENT lt gt Harmar MN V OBILITY MADE EASY
Download Pdf Manuals
Related Search