BLDC Motor Control with Hall Effect Sensors Using the 9S08MP
Contents
1. Freescale Semiconductor Application Note Document Number AN4058 Rev 0 4 2010 BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP by Eduardo Viramontes Systems and Applications Engineering Freescale Technical Support 1 Introduction This application note describes a brushless DC BLDC motor control system using a predefined hardware reference design It explains the hardware concept not in detail for further details about the hardware look for the user guide titled 3 Phase BLDC PMSM Low Voltage Motor Control Drive document LVMCDBLDCPMSMUG and the user manual titled MC9SO8MP16 Controller Daughter Board for BLDC PMSM Motor Control Drive document LVBLDCMP16DBUM at www freescale com This application uses the MC9SO8MP 8 bit microcontroller The device has specialized control hardware that allows for reduced software overhead and higher control efficiency BLDC motors are more frequently used over traditional brushed motors for their increased efficiency and reduced maintenance needs mainly through elimination of wearable and friction causing brushes The reduced cost of embedded systems plus the features in microcontrollers like the MC9SO8MP make it more convenient to offer motor control systems for BLDC motors even with their incremented cost because of the need for permanent magnets The benefits in ease of control usually outweighs the added cost of BLDC motors Their speed is directly proportional to the2. No 118 Jianguo Road Chaoyang District Beijing 100022 China 86 10 5879 8000 support asia freescale com For Literature Requests Only Freescale Semiconductor Literature Distribution Center 1 800 441 2447 or 1 303 675 2140 Fax 1 303 675 2150 LDCForFreescaleSemiconductor hibbertgroup com Document Number AN4058 Rev 0 4 2010 Information in this document is provided solely to enable system and sofware implementers to use Freescale Semiconductors products There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document Freescale Semiconductor reserves the right to make changes without further notice to any products herein Freescale Semiconductor makes no warranty representation or guarantee regarding the suitability of its products for any particular purpose nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit and specifically disclaims any liability including without limitation consequential or incidental damages Typical parameters that may be provided in Freescale Semiconductor data sheets and or specifications can and do vary in different applications and actual performance may vary over time All operating parameters including Typicals must be validated for each customer application by customer s technical experts Freescale Semiconductor
3. Phase BLDC PMSM Low Voltage Motor Control Drive board is a under the number LYMCDBLDCPMSMUG The user guide contains the schematic of the board a description of individual function blocks and a bill of materials i Miti itiiti jfi EAN n E E n a bi ei a S Figure 1 Three phase BLDC PMSM low voltage motor control drive 2 1 BLDC Basics The BLDC basics are e The 3 Phase BLDC motor e Commutation Moving the BLDC motor e Controlling speed and torque 2 1 1 Three Phase BLDC Motor The brushless BLDC motor is also referred to as an electronically commuted motor There are no brushes on the rotor and at certain rotor positions commutation is performed electronically The stator magnetic circuit is usually made from magnetic steel sheets Stator phase windings are inserted in the slots distributed winding as shown in Figure 2 or wound as one coil on the magnetic pole Magnetization of the permanent magnets and their displacement on the rotor are chosen in such a way that the back EMF the voltage induced into the stator winding due to rotor movement shape is trapezoidal This allows a rectangular shaped 3 phase voltage system see Figure 3 to create a rotational field with low torque ripples BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 2 Freescale Semiconductor Inc System Description Stator _ Stator winding in slots Shaft Air gap Per
4. does not convey any license under its patent rights nor the rights of others Freescale Semiconductor prodcuts are not designed intended or authorized for use as components in systems intended for surgical implant into the body or other applications intended to support or sustain life or for any other application in which failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application Buyer shall indemnify Freescale Semiconductor and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unauthorized use even if such claims alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part RoHS compliant and or Pb free versions of Freescale products have the functionality and electrical characteristics as their non RoHS complaint and or non Pb free counterparts For further information see http www freescale com or contact your Freescale sales representative For information on Freescale s Environmental Products program go to http www freescale com epp Freescale and the Freescale logo are trademarks of Freescale Semiconductor Inc
5. the PWM only on one side of the phase The complementary approach modulates both sides The complementary and independent approaches allow the control to address either a 2 or 4 quadrant operation as shown in Figure 8 BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 6 Freescale Semiconductor Inc nn eeeeees testsC SNCSCSC agO System Description ja Second Quadrant gt negative speed positive torque 6 reverse braking Generating Motoring Third Quadrant negative speed negative torque reverse accelerating Torque IV First Quadrant positive speed positive torque forward accelerating Motoring voltage speed Generating Fourth Quadrant positive speed negative torque forward braking Figure 8 Four quadrants of motor operation The 2 quadrant operation provides a defined voltage and current of the same polarity positive voltage with positive current or negative voltage and negative current operating quadrants I and III in Figure 8 The 4 quadrant PWM switching covers the operation of the generated voltage in all four quadrants This is provided using complementary switching of the top and bottom transistors The benefits of the 4 quadrant PWM operation are e Motoring and generating mode control there is a possibility of braking the motor via the 0 to 50 duty cycle which is not used in rotating the motor e Linear operation in all f
6. the processor to determine the next commutation with the six step process and the Hall effect sensor outputs Table 1 shows an example of this concept Table 1 Hall effect switches Hall Sensor A Hall Sensor B Hall Sensor C C r p r ea e e a C a C Cs ee LE e eN e With this table in the memory the commutation software driver becomes simple making a small code memory footprint as opposed to the sensorless approach that requires more software bandwidth and memory space More information on the sensorless approach with the 9S08MP16 can be found in the design reference manual titled 3 Phase Sensorless BLDC Motor Control Using MC9SOSMP16 document DRM117 at www freescale com Figure 7 shows a single 60 commutation taking place As shown in the six step process here two motor phases are activated for each commutation VOC VOC Phase A Phase A P Phase C Phase B Phase C hase B u a WOC OG Actual fug Maw fuz vector vector Figure 7 One step of six step commutation process Notice in the first instance only phases A and C are turned on with current flowing into A and out of C After the commutation the current is flowing into A and out of B with no current flowing into or out of C BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 Freescale Semiconductor Inc 5 System Description 2 1 3 Controlling Speed and Torque Commutation allows the movement of the motor and gets the motor turning Th
7. this application note By monitoring the speed and current in the motor while the commutation process is running the average voltage input into the motor is incremented and decreased this directly affects the speed and torque of the motor The six step controller uses one of two PWM techniques 1 Unipolar PWM switching This technique refers to motor phases being switched in such a way that one of the phases returns current while the PWM modulation is happening in another phase this is unipolar 2 Bipolar PWM switching This technique refers to the voltage passing through the two phases as being modulated with the PWM both the input and output of current are being modulated Unipolar and bipolar switching have specific advantages Unipolar switching reduces electromagnetic noise and the DC bus ripple because there is less switching Bipolar switching is better suited for sensorless approaches where it is necessary to sense back electromagnetic forces BEMF The bipolar approach has the zero volt point at a 50 duty cycle therefore there is more time to sense the BEMF For more information on sensorless approaches look for document DRM117 at www freescale com Both unipolar and bipolar approaches can be either independent or complementary Unipolar and bipolar approaches refer to the relationship of the two phases The complementary approach refers to the relationship of the two signals controlling one phase The independent approach applies to
8. 0 to the next position The six steps cause a full revolution 6 steps x 60 360 Figure 3 and Figure 5 are the same but Figure 5 shows the six steps For each step positive position U means high side transistor on and low side off negative position U means high side transistor off and low side on and neutral position means both transistors are on Voltage L Phase A U Phase B Phase C p 60 g 120 10 180 270 240 270 300 3 0 Electrical angle T 1 2 4 Figure 5 Three Phase voltage system with six step commutation vectors The previous image shows the six step process in a time based system Figure 6 shows it in a rotational system i ABC ABC 011 Phase B ABC 001 ABC 101 ABC Hall Sensors Oulpul Figure 6 Six step commutation process in a rotational representation Notice the six vectors pointing to six distinct directions and separated by 60 The image also introduces the concept of sensors There has to be a sensor giving feedback to the system indicating when the rotor has reached the desired position If commutation is done faster than this the rotor magnets go out of sync with the stator magnetic field and the rotor vibrates instead of rotating There needs to be a sensing method to determine if the position of the rotor is in sync with the stator so that the next commutation can be made There are many types of sensors used in motors encoders
9. All other product or service names are the property of their respective owners 2010 Freescale Semiconductor Inc s 2 freescale smcoiductor
10. M with the comparison window of the analog comparators and PWM output synchronizes with the FTM PWM output e One serial peripheral interface SPI e One serial communications interface SCI with LIN slave functionality One inter integrated circuit C port e On board 3 3 V to 2 5 V voltage regulator for powering internal logic and memories e Integrated power on reset and a low voltage interrupt module e Multiplexing of all pins with the general purpose input output GPIO pins e Computer operating properly COP watchdog timer e External reset input pin for hardware reset e Internal clock source ICS Containing a frequency locked loop FLL controlled by an internal or external reference 2 3 System Block Diagram Figure 12 shows the full application hardware structure including internal MCU connections and external circuitry BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 Freescale Semiconductor Inc 9 Software Description 3 Phase BLDC PMSM Low Voltage Motor Control Drive 3 Phase Inverter AAM DOC Power Input Ov er currert FAULT fo Parts superior system Application Monitoring and Control Hall sensor Period LT Es Desired Actual speed _ speed gt Required speed Limitations DC Bus Current irishi d rite b nu oa Required 4 ae torque SOSMP16 Figure 12 System block diagram 3 Software Description These a
11. applied voltage low maintenance and ease of customization of control parameters 2 System Description This application consists of three parts 2009 Freescale Semiconductor Inc n Contents PAU e aC asinine 1 arem DE an 1 Al BLOC i ecco eee earns 2 2 1 1 Three Phase BLDC Motot 0 000 2 2 1 2 Commutation Moving the BLDC BOT ie eauaigekaetiateyaaieneieaial 3 2 1 3 Controlling Speed and Torque 6 2 2 9SO8MP16 Controller Advantages and POR TG Gd racer een 9 2 3 System Block Diagram viccisircisouisecuscensese 9 Saltware Det eines 10 AOC Seara 11 a cases remienaniorceeonanas 12 P od freescale STMCINTOtor System Description e This document Describing the application and its usage e Application code Included as an attachment to the application note e FreeMaster control page Also included as an attachment to the application note As mentioned before the hardware used in this application note is covered elsewhere It is based on a 3 phase BLDC PMSM low voltage motor control drive board module that provides a broad solution for testing and developing low power drives and demos with a list of microcontrollers and DSC daughter boards See Figure 1 It demonstrates the MC9SO8MP16 abilities and provides a hardware tool to help develop applications using the MC9SO8MP16 targeted at motor control applications See a detailed description including the hardware specification of the users manual 3
12. e already lengthy matter of calculating the control outputs this also affects the maximum attainable speed In conclusion the decision to go for a sensorless or sensor approach must be weighed between total system cost including available components and space and desired performance The SO8MP16 has enough resources to do both sensorless and sensor BLDC motor control having such a low cost and a need for a small amount of external components it is an ideal option for any of the two options BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 12 Freescale Semiconductor Inc How to Reach Us Home Page www freescale com Web Support http www freescale com support USA Europe or Locations Not Listed Freescale Semiconductor Technical Information Center EL516 2100 East Elliot Road Tempe Arizona 85284 1 800 521 6274 or 1 480 768 2130 www freescale com support Europe Middle East and Africa Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen Germany 44 1296 380 456 English 46 8 52200080 English 49 89 92103 559 German 33 1 69 35 48 48 French www freescale com support Japan Freescale Semiconductor Japan Ltd Headquarters ARCO Tower 15F 1 8 1 Shimo Meguro Meguro ku Tokyo 153 0064 Japan 0120 191014 or 81 3 5437 9125 support japan freescale com Asia Pacific Freescale Semiconductor China Ltd Exchange Building 23F
13. e purpose of moving a motor is controlling speed and torque Speed in a BLDC motor is directly proportional to the voltage applied to the stator While commutation keeps the magnetic flux vector rotating the speed at which the actual rotor is forced to the next position is determined by the strength of this magnetic force and this is determined by the voltage applied to the stator windings By using PWMs at a higher frequency than the commutations the amount of voltage applied to the stator can be easily controlled therefore the speed of the motor can be controlled Torque is also controlled by reducing stator voltage when the torque load of the motor is higher than indicated These control parameters require sensors The Hall effect sensors that are used to detect the position of the rotor are also used to detect speed by measuring the time it takes for the sensors to switch An input capture channel from the microcontroller timer is used to measure the length of a pulse for one of the Hall effect sensors The measured time is converted into revolutions per minute RPM Torque is sensed as a relationship of the current consumed by the motor Torque can be measured individually for each of the three phases or as an average in the DC bus feeding the motor The measurement of torque in the DC bus is simpler because it requires only one ADC channel and the software resources to treat this single channel This added simplicity is the reason why it is used in
14. ith Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 8 Freescale Semiconductor Inc System Description 2 2 9SO8MP16 Controller Advantages and Features The MC9SO8MP16 is a member of the low cost high performance HCS08 Family of 8 bit microcontroller units MCUs All MCUs in this family use the enhanced HCS08 core and are available with a variety of modules memory sizes memory types and package types The Freescale MC9SO8MP16 microcontroller is well suited for digital motor control offering many dedicated peripherals such as Flextimer FTM modules analog to digital converters ADC timers communications peripherals SCI SPI PC and on board flash and RAM The MC9S08MP16 device provides the following features e Two Flextimer modules with a total of eight channels e One analog to digital converter ADC 13 channel 12 bit resolution 2 5 us conversion time e One 8 bit modulo counter with an 8 bit prescaler and overflow interrupt e Interrupt priority controller IPC with four programmable interrupt priority levels e One differential programmable gain amplifier PGA with a programmable gain x1 x2 x4 x8 x16 or x32 e Three fast analog comparators HSCMP1 HSCMP2 and HSCMP3 with both positive and negative inputs e Three 5 bit digital to analog converters DAC used as a 32 tap voltage reference e Two programmable delay blocks PDB PDB1 synchronizes the PWM with the samples from the ADC PDB2 synchronizes the PW
15. ling through the programmable delay block module PDB This provides measurements at constant and adequate intervals Fault checking process Manages the hardware over current detection provided by the FTM timer module as well as monitoring for DB bus voltage and other variables e Commutation process Manages reading the hall effect sensors to determine when the next commutation will take place and what signals will be switched It uses the 3pps_bldc driver to define the next stage of commutation 4 Application Setup Figure 14 shows the basic system connections BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 Freescale Semiconductor Inc 11 Conclusion USE BDM interface Figure 14 Basic system connections e 6 pin BDM connector J3 Is located on the MP16 daughter card It is used to program and debug the MCU with this application software or other software via Code Warrior e USB connector J10 Contains a Freescale MCU that emulates a COM port via USB This is connected to the serial communications interface in the SO8SMP16 to run FreeMASTER communications The USB port connected to the PC installs itself as a COM port e Jl Is the powered PWM output to the BLDC motor e J6 Is the Hall effect sensor input from the motor sensors 5 Conclusion This document demonstrates a BLDC motor control application using Hall effect sensors as a feedback mechanism to measure speed and positi
16. manent magnets Figure 2 BLDC motor cross section Voltage l Phase A Phase C T 30 60 90 120 150 180 210 240 270 300 330 electrical angle Figure 3 Three phase voltage system 2 1 2 Commutation Moving the BLDC Motor BLDC motors can be driven with simple rectangular waveforms while other motors such as AC induction motors require the generation of sinusoidal waveforms This is due to the synchronous nature and trapezoidal winding of the stator poles of the BLDC motor To drive this rectangular waveform only general purpose in out GPIO pins and a 3 phase H bridge is needed The H bridge system uses a high side and low side transistor for each of the phases allowing it to control the direction of the current flowing into and out of the motor winding This creates positive and negative magnetic flows that placed in the proper order create flow vectors that cause movement Uice GNO Phase A Pha se B Phase C Figure 4 Three phase H bridge BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 Freescale Semiconductor Inc 3 System Description Commutation is the process where voltage is applied to the motor phases in such a way that it keeps the motor rotating magnetic flux vector rotating Commutation for BLDC motors are a six step process All six sides of the 3 phase H bridge are turned on and off to create the six flow vectors These vectors make the BLDC motor point 6
17. me insertion is typical for all 4 quadrant power stage operations The 4 quadrant operation is enabled by the complementary operation from the top and bottom switches This requires a dead time insertion because the switching transient causes a DC Bus short circuit with fatal power stage damage The bipolar PWM switching is not as popular as the unipolar switching due to a bad electromagnetic emission of the motor This is because the PWM ripple is twice that of the DC Bus voltage On the other hand this switching is better for sensorless rotor position sensing This switching can be implemented using the MC9SO8MPI16 2 1 3 2 3 Phase BLDC 6 Step Control with Unipolar Soft PWM Switching The most common 6 step commutation with unipolar complementary 4 quadrant PWM switching techniques is shown in Figure 11 Oo rrinnu tabior commutation commutaban COMTI Teta COMMU TET COTM camm bation gamn helio 120 i Bg i N i i 1 H Figure 11 Unipolar PWM switching The unipolar PWM switching can control the BLDC motor with an almost identical linear voltage and current performance The only difference is that the PWM duty cycle 0 creates an average voltage of 0 The main advance of the unipolar PWM switching has better EMC compatibility due to half of the voltage ripple compared to the bipolar switching This switching is implemented as default for this application by using the MC9SO8MP16 BLDC Motor Control w
18. on of the motor rotor The SOSMP16 MCU is an ideal choice for controlling BLDC motors It is low cost and has all the resources to do such a task leaving enough software resources to run other tasks The advantage of using Hall effect sensors in BLDC motor control is that the feedback mechanism requires minimal CPU resources as opposed to sensorless approaches where more software and hardware resources are used for the detection of proper commutation and speed Hall effect sensors also offer an advantage of control at a near zero rpm speed range Sensorless approaches need the motor to start moving by moving it without any feedback to be able to detect back EMF and Hall effect sensors to always indicate the position of the motor to easily start running it in a closed loop from zero rpm Though the SO8MP16 is comfortably suited to do sensorless BLDC motor control the use of Hall effect sensors free up CPU resources for other tasks The SO8MP16 is also ready to generate adequate PWM signaling and is still a wise choice given the low price point it has An added advantage of using Hall effect sensors is that the maximum speed attainable is higher than with a sensorless approach Sensorless approaches depend greatly on the ADC comparator sampling frequency which is always slower than the MCU capacity to detect changes in GPIO pins There is also the matter of calculating when the next commutation should take place which also drains CPU resources and adds to th
19. our quadrants The MC9SO8MP16 is able to control the 3 phase power stage with a unipolar and bipolar PWM with a more advanced 4 quadrant operation In the following sections the transistor control pattern for the 4 quadrant PWM technique is discussed 2 1 3 1 3 Phase BLDC 6 Step Control with Bipolar Hard PWM Switching The PWM commutation pattern of the bipolar complementary 4 quadrant PWM switching technique is shown in Figure 9 COMMU tat cr commutation commutation commutation Sorin tati on commutation commutation Commu bat on 1 y i oy ral H i n AINA H nning m pjer Sphase Brushless C motor none Figure 9 Bipolar PWM switching BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 Freescale Semiconductor Inc System Description Dead Dead Dead Dead Dead Dead Time Tone Tone Time Tone Time Sua O TL i E i i g i Ei bi Ii i i ii i 1 i D i E bi iu F i i id lt a gt fo bE ig Dead Dead Swap o Dead Dead Time Time Time Tine Figure 10 Bipolar PWM switching Detail Details of the technique are shown in Figure 10 Notice the characteristic of the bipolar 4 quadrant complementary switching The bipolar switching requires that the top and bottom switch PWM signals be swapped Another important detail is the introduction of dead time insertion in the complementary top and bottom signals This dead ti
20. potentiometers switches and others The most common type of sensor used in BLDC motors is the Hall effect sensor The Hall effect sensor is a sensing switch that outputs a logic level based on the detection of a magnetic field Hall effect sensors are economical and because of the permanent magnets inside a BLDC motor are easy to install inside the motor The motor in this application note comes with the Hall effect sensors pre installed Because of the six step control scheme there is no need for a high resolution output from the sensor The BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 4 Freescale Semiconductor Inc System Description only thing you need to know 1s if the rotor advanced 60 This can be known with three Hall effect sensors one for each phase and the output combinations they generate Figure 5 shows for every 60 there is a specific combination output from the three Hall effect sensors NOTE The Hall effect sensors are usually positioned so that the magnets change its values before the rotor is actually in the next commutation position This allows for the next commutation to be made before the rotor actually becomes stuck at one position With Hall effect sensors a simple BLDC control system needs only 9 pins from a microcontroller six pins to control the H bridge and three pins to sense the Hall effect switches Software up to this point is also simple A table in the memory is enough for
21. re the main processes running in the BLDC motor control with HAII effect sensor applications e BLDC application main process Defined by the bldcStateIndex it controls the main application states This process manages both speed and torque controlling and runs most of the application s math see Figure 13 BLDC Motor Control with Hall Effect Sensors Using the 9SO8MP Rev 0 4 2010 10 Freescale Semiconductor Inc Application Setup DC Bus Current Limit Actual DC Bus Current Velocity Required rpm To PWM Velocity Actual rpm 60 6 p T Period from ha effect sensor Figure 13 Control scheme FreeMASTER process The FreeMASTER process provides communication between the application and a PC interface The communication protocol and requirements are defined by FreeMASTER This process is in charge of updating the variables that are sent to the PC application and managing the serial port communication to send them More information FreeMASTER can be found at www freescale com The attached project also includes the control pages that run integrated to the FreeMASTER software to externally control the application It is also used to tune application parameters like the acceleration ramp or the PI controller parameters e ADC sensing process Manages sampling values for bus DC voltage and current as well as temperature sensing for informative purposes The current sensing is synchronized with PWM signa
Download Pdf Manuals
Related Search