For your own safety, please read this user manual carefully before
Contents
1. KEEP THIS MANUAL FOR FUTURE NEEDS Ce For your own safety please read this user manual carefully before installing the device CAUTION amp K eep this device away from rain and moisture OD Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow carefully the instructions of this manual INTRODUCTION Thank you for having chosen this professional moving head You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find the fixture device a power cable an XLR connection cable a safety cable and this manual Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device Features e pan 540 tilt 265 e colors e color wheell with 4 dichroic glass panes 2 correction filter 1 UV filter e color wheel2 with 6 dichroic glass panes for a total of 7 colors static gobo wheel has 5 static gobos plus open with different speed gobo shaking rotating gobo wheel has 5 rotating gobos plus open all gobos can be easily replaceable and gobo indexing strobe effect 0 13 flashes per second or random strobe Stepless Zoom automatic program dis2. Before mounting make sure that the installation area can hold a minimum point load of 10 times the 5 GS SMS Y1200 V1 0 02NR device s weight Connect the fixture to the mains with the power plug installation via the Omega holders 1 Omega holders 2 Clamp 3 Safety rope 2 lecum Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective 4 Quick lock fastener aja tur holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw 6 GS SMS Y1200 V1 0 02NR DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX Ausgang DMX Eingang DMX Ausgang DMX Eingang XLR Einbaubuchse XLR Einbaustecker XLR Einbaubuchse XLR Einbaustecker
3. 1 Gnd 1 Gnd 2 Signal 2 Signal 3 Signal 3 Signal ANA 5 N A DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 PINS PIN2 a a aO CONTROLLER Address 39 Address 20 Address 1 Projector DMX start address selection All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device 7 GS SMS Y1200 V1 0 02NR You can set the same starting address for all fixtures or a group of fixtures or make different address for each fixture individually If you set the same address all the units will start to listen to the same control signal from the same channel number In other wo
4. 44 Fix gobo2 45 59 Fix gobo 3 60 74 Fixgobo4 75 89 Fix gobo 5 90 113 Gobo 1 shake slow to fast 114 137 Gobo 2 shake slow to fast 138 161 Gobo 3 shake slow to fast 162 185 Gobo 4 shake slow to fast 186 209 Gobo 5 shake slow to fast 210 255 Fix gobo wheel cont rotation slow to fast 11 GS SMS Y1200 V1 0 02NR Channel 5 PAN movement 8bit Channel6 TILT movement 8bit Channel 7 Speed pan tilt movement 0 14 max speed 15 225 max to min speed 226 235 blackout by movement 236 245 blackout by all wheel changing 246 255 no function Channel8 prism prisms macros 0 25 open 26 51 3 facet prism 52 77 bfacet prism 78 103 7 facet prism 104 127 trapezoid prism 128 135 Macro 1 136 143 Macro 2 144 151 Macro 3 152 159 Macro 4 160 167 Macro 5 168 175 Macro 6 176 183 Macro 7 184 191 Macro 8 192 199 Macro 9 200 207 Macro 10 208 215 Macro 11 216 223 Macro 12 224 231 Macro 13 232 239 Macro 14 240 247 Macro 15 248 255 Macro 16 Channel 9 Rotating prism index rotating prism rotation 0 127 Prism indexing 128 187 Forwards Prism rotation from fast to slow 188 193 No rotation 194 255 Backwards Prism rotation from slow to fast Channel 10 Shutter strobe 0 31 Shutter closed 32 63 Dimmer control shutter open 12 GS SMS Y1200 V1 0 02NR 64 95 Strobe effect slow to fast 96 127 No function shutter open 128 159 Pulse effect in sequences 160 191 No function shutter open 192 223 Random strobe effect sl
5. display may show XXer while there are problems with one or more channels XX stands for channel 1 2 3 5 6 7 who has the testing sensor for positioning For example when the display shows 02Er it means there is some error in channel 2 If there are some errors on channel 1 channel 2 channel 5 at the same time you may see the error message O1Er 02bEr OSEr flash repeated for 5 times and then the fixture will generate a reset signal all the stepper reset If the fixture remain error message after performing reset more than 3 times it will detect whether the fixture has more than 3 errors If the fixture has more than 3 errors including 3 errors all the channels can not work properly but if the fixture has less than 3 errors only the channels which have errors can not work properly others can work as usual 01Er Color wheell error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its drive circuit on the main PCB The color wheel is not located in the default position after the reset 02Er Rotating gobo wheel error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its drive circuit on the main PCB The rotating gobo wheel is not located in the default position after the
6. menu You can change the selection by pressing the Up button Confirm every selection by pressing the Enter button You can leave every mode by pressing the Mode esc button The functions provided are described in the following sections amp GS SMS Y1200 V1 0 02NR Function Set DMX address DMX setting Mode Value display DMX value display Set to Slave Set to slave Auto program Auto program Music control Music control Informat Time information Power on time XXXX Individual fixture running ion time Machine on time XXXX Fixture running time Lamp on time XXXX Lamp running time Lamp off time XXXX Lamp closed time Clear Lamp time Please wait 7 Clear lamp time Temp Info System Temp XX C Ambient time Near lamp Temp XXX C Temp in lamp chamber Product Info Unit model Unit model Unit code Unit code Company WEB Company WEB Company Tel Company Tel Software version ICOI Verl 0 Software version of each IC ICXX Ver9 9 Personali Effect Set Pan Reverse ON OFF ty Tilt Reverse ON OFF Reverse movement Blackout moving ON OFF Blackout colors ON OFF Blackout while pan tilt Blackout Gobos ON OFF moving or color gobo wheel Scan fine select ON OFF moving Status choose Addr via DMX ON OFF Add resetable via DMX Master or Alone Master Alone Master Alnow switch Auto if no DMX ON OFF Auto run if no DMX Music if no DMX ON OFF Music control if no DMX Lamp co
7. reset 03Er Rotating gobo indexing error This message will appear after the reset of the fixture and if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The rotating gobo is not located in the default position after the reset 04Er Static gobo wheel error This message will appear after the reset of the fixture if the yoke s magnetic indexing 14 GS SMS Y1200 V1 0 02NR circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Static gobo wheel error is not located in the default position after the reset 05Er PAN yoke movement error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The PAN yoke is not located in the default position after the reset 06Er TILT head movement error This message will appear after the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The TILT head is not located in the default position after the reset 08Er Prism wheel error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunctio
8. the installation The installation must only be carried out by a qualified person The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year A CAUTION B efore taking into operation for the first time the installation has to be approved by an expert Cautions The effect should be installed outside areas where persons may reach it walk by or be seated CAUTION W hen installing the device make sure there is no highly inflammable material within a distance of min 0 5m Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury A CAUTION The electric connection must only be carried out by a qualified electrician
9. C 50Hz L1230VAC 50Hz L 240V AC 50Hz 208VAC 60Hz L1220VAC 60Hz L1230VAC 60Hz L1240VA C 60Hz Power consumption max 1500 W Lamp MSR 1200 SA GY 22 socket Metal Halide Motors 16 micro motors Flight case dimensions 65 x 60 x 72 cm Net weight 58 KGS Gross weight 63 KGS Carton packing 98 KGS Flight case packing Remark errors and omissions for every information given in this manual excepted All information is subject to change without prior notice 16 GS SMS Y1200 V1 0 02NR
10. he technical specifications in the last page of this manual the device was designed for indoor use only Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 5 meter Always fix the fixture with an appropriate safety cable if you use the clamp to hang up the fixture When fixing the device on a raised from the ground support be sure to use no less than screws and nuts of M10 x 25 mm and insert them in the pre arranged screw holes in the base of the fixture If you use the quick lock cam in hanging up the fixture please make sure the 4 quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported 3 GS SMS Y1200 V1 0 02NR For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way d
11. ifferent to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS a Installing or replacing the lamp h a higher wattage They generate higher temperatures than which the device was designed for For the installation you need one MSR 1200 SA GY22 lamp Procedure 1 Unscrew the 4 screws marked Y X W and Z on the back of the housing holding the plate where the lamp is underneath 2 Gently pull the socket holder of the lamp housing in the middle 3 Carefully insert the lamp into the socket Please remember there is only one way to insert the lamp Gently slide the lamp and its lamp holder back into place and fasten the 4 screws 4 On the access plate there are 3 small screws marked A B and C which are used to adjust the lamp holder in the lamp housing You can adjust the 3 screws to fine turn the position of the lamp to get the maximum light output as shown below Please remember the lamp is not a hot restrike type you must wait for approximately 10 minutes after having turned off the lamp before you can turn it back on again A CAUTION Do not operate this device with open cover b Mounting the device 4 GS SMS Y1200 V1 0 02NR AN CAUTION Please consider the EN 60598 2 17 and the other respective national norms during
12. n sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Prism wheel is not located in the default position after the reset 09Er prism indexing error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The prism indexing is not located in the default position after the reset 12Er Focus error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Focus is not located in the default position after the reset 13Er Zoom error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Zoom is not located in the default position after the reset 14Er Iris error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Iris is not located in the default position after the reset 15Er Color wheel2 error This message will appear after the rese
13. ntrol Lamp on or off ON OFF Lamp on off Lamp on by power on ON OFF Lamp on with power on Lamp on via DMX ON OFF Lamp on via DMX Lamp off via DMX ON OFF Lamp off via DMX Lamp off if no DMX ON OFF Lamp off if no DMX Lamp ignited temp XX Max lamp on temp Max lamp off temp XX Max lamp off temp Display set Display close time 05M Display close time Display intensity 20 9994 LCD brightness Init effect PAN Moving PAN Moving XXX Initial effect position Save and Active Please wait 7 GS SMS Y1200 V1 0 02NR Mic sensitivity 0 99 Sensitivity of Mic Reset default ON OFF Restore factory settings Reset Reset All Reset all motors amp return to home function Reset Scan Reset only motors for pan tilt Reset Colors Reset only motors for colors Reset Gobos Reset only motors for gobo Reset Shutter Reset only motors for shutter Reset Others and or dimmer Reset other motors Effect Test channel PAN Moving Automatically test the function Adjust Lamp adjustment PAN Moving PAN Moving XXX Lamp adjustment Save Active Please wait 7 Wheel adjustment Color wheel Color wheel XXX Wheel adjustment Save and Active Please wait 7 Users User mode User A seetings User s mode Mode User B settings Set User C settings Preset User mode PAN PAN CH NO 01 Preset User modes Save and Active Please wait 7 Edit Select Programs Pr
14. ogram 1 Select programs to be run Program H Program 10 Edit program Program 1 Program Test STEP Testing program Start step XX Program in loop Program 10 End step Start Save and exit step xxx End step xxx Edit scenes Edit Scene 001 Input by outside Save and automatically return Edit Scene 250 Save and Active manual scenes edit Secne Time TIME X Pan Tilt X XS Pan xxx Auto scenes Rec XX XX Automated recording scenes INSTRUCTIONS ON USE DMX channel s functions and their values 19 DMX channels Channel 1 0 13 14 27 28 41 42 55 Color Wheel Open white Light blue Salmon pink Blue LE 10 GS SMS Y1200 V1 0 02NR 56 69 Yellow Green 70 83 Light Yellow 84 97 Magenta 98 111 Orange 112 127 Purple 128 187 Forwards rainbow effect from fast to slow 188 193 No rotation 194 255 Backwards rainbow effect from slow to fast Channel 2 Rotating gobos cont rotation 0 14 Open 15 29 Rot gobo 1 30 44 Rot gobo 2 45 59 Rot gobo 3 60 74 Rot gobo 4 75 106 Gobo 1 shake slow to fast 107 138 Gobo 2 shake slow to fast 139 170 Gobo 3 shake slow to fast 171 202 Gobo 4 shake slow to fast 203 255 Rot gobo wheel cont rotation slow to fast Channel 3 Rotating gobo index rotating gobo rotation 0 127 Gobo indexing 128 187 Forwards gobo rotation from fast to slow 188 193 No rotation 194 255 Backwards gobo rotation from slow to fast Channel 4 Fixed Gobos 0 14 Open 15 29 Fix gobo 1 30
15. ow to fast 224 255 No function shutter open Channel 11 Dimmer intensity 0 255 Intensity 0 10096 Channel 12 Focus 0 255 Continuous adjustment from far to near Channel 13 Zoom 0 63 Zoom 1 64 127 Zoom2 128 191 Zoom3 192 255 Zoom 4 Channel 14 Iris 0 191 Max diameter to Min diameter 192 223 Pulse closing fast to slow 224 255 Pulse opening slow to fast Channel 15 Color Wheel 2 0 13 Open white 14 27 Red 28 41 Light blue 42 55 Pink 56 69 Dark Yellow 70 83 3200K correction filters 84 97 5600K correction filters 98 111 UV filter 112 127 Green 128 187 Forwards rainbow effect from fast to slow 188 193 No rotation 194 255 Backwards rainbow effect from slow to fast Channel 16 Frost 0 191 Frost 0 100 192 223 Pulse opening fast to slow 224 255 Pulse closing slow to fast 2 du GS SMS Y1200 V1 0 02NR Channel 17 Lamp on off reset internal programs 0 19 colour change normal by direction depend on distance 20 39 colour change to any position by direction depend on distance 40 59 Lamp on 60 79 Lamp switch off 80 99 Motor reset 100 119 Internal program 1 120 139 Internal program 2 140 159 Internal program 3 160 179 Internal program 4 180 199 Internal program 5 200 219 Internal program 6 220 239 Internal program 7 240 255 Internal program 8 Channel 18 Pan fine 16bit Channel 19 Tilt fine 16bit ERROR MESSAGE When you turn on the fixture it will make a reset first The
16. play digital address and function setting High speed pan amp tilt movements Control board with 4 digit display and foil keyboard for adjusting the DMX starting address Pan tilt Reverse Program Reset lamp on off operating hours and etc e digital display can be turn 180 reverse to fit for different installation position local or remote resetting e lamp switches ON OFF locally e auto test for all functions e value of each DM X channel can be displayed 1 GS SMS Y1200 V1 0 02NR e Editable program edit and save the program to the incorporated EEPROM through the front control panel or external controller can save maximum 48 scenes and run the saved program by the run menu from the front control panel SAFETY INSTRUCTIONS CAUTION Be very careful during installation Since you will be working with a dangerous voltage you can suffer a life threatening electric shock when touching live wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual IMPORTANT D amages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediatel
17. rds changing the settings of one channel will affect all the fixtures simultaneously If you set a different address each unit will start to listen to the channel number you have set based on the quantity of control channels of the unit That means changing the settings of one channel will affect only the selected fixture In the case of the spot head which is a 10 channel fixture you should set the starting address of the first unit to 1 the second unit to 20 19 1 the third to 39 20 19 and so on Note After switching on the machine will automatically detect whether DMX 512 data is received or not If the data is received the display will show A 001 with the actually set address If there is no data received at the DMX input the display flashes A001 with the actually set address This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the machine the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Control Board The Control Board offers several features you can simply set the starting address switch on and off the lamp run the pre programmed program or make a reset The main menu is accessed by pressing the Mode esc button until the display starts flashing Browse through the menu by pressing the Up button Press the Enter button in order to select the desired
18. t of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Color wheel is not located in the default position after the reset CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 1 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 2 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed 15 GS SMS Y1200 V1 0 02NR OD CAUTION Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the lamp Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer TECHNICAL SPECIFICATIONS Power supply 208VAC 50Hz L1220VA
19. y The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually 2 GS SMS Y1200 V1 0 02NR A CAUTION Never touch the device during operation The housing may heat up AN CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in t
Download Pdf Manuals
Related Search