Manual - Premier Mounts
Contents
1. Attaching the Mount Carriage section Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions 4 EST150 A Attaching the Mount Carriage Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 allowance mark on the small straw or toothpick as shown pe in Figure 2 and Figure 3 do not use this screw The Marking the Depth screw length must not bypass the mark X Threaded Insert 6 Test each size of the screws provided The correct screws should thread easily into the mounting point and not pull out Small Straw or Toothpick when tension is applied 2 Does your projector have multiple mounting points or a single mounting point If your projector has multiple mounting points P proceed to the Multiple Mounting Point l Installation section or Toothpick Mae or Toothpick If your projector has a single mounting point skip to the Sin2. SAFE INSTALLATION EST150 Installation lt lt Wood Stud Use an electronic stud finder not supplied to locate the center of the stud that is in the wall Stud finder Use a pencil to mark the first mounting point just above your height mark from page 5 X4e Height Mark from page 5 Use the level to make sure the projector arm is level from side to side 2 Place the projector arm s second mounting hole over the first mounting point mark then use a pencil to mark the upper mounting point Marking I Projector Two 2 mounting points must be used Arm lt lt Wood Stud Page 6 Visit the Premier Mounts website at http www premiermounts com Installation Instructions EST150 22 Marking Once the mounting points have been marked use a 3 drill bit and portable drill to drill the pilot holes After the pilot holes have been drilled use two 2 14 x 2 wood screws to mount the projector Marking arm to the wooden stud 14 x 2 Wood Screw X Projector Arm lt Wood Stud Use two 2 M5 x 10mm security screws to attach the projector arm cover plate to the projector arm Go to the Throw Distance Calculation section on page 10 Wood stud not shown Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 7 24 EST150 Please review the Operator s Manual that came packaged with your projector before attachi
3. gt D PREMIER C4 MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Single Stud Short Throw Projector Wall Mount Model EST150 NORTH AMERICA EUROPE 3130 East Miraloma Avenue Unit 3 The Moorings Business Park Channel Way Anaheim CA 92806 USA Longford Coventry CV6 6RH UK USA and Canada Phone 44 0 24 7664 4105 Phone 1 800 368 9700 Fax 44 0 24 7664 4165 Fax 1 800 832 4888 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 9530 011 021 01 A EST150 A Table of Contents Weight Capacity sist it iccctnrnecdndanouaneanndnns Warning Statements a a Installation Tools oe Parts List ea ee eer eee Features oi cescsnnsmnnnmnnnnenennnnanenenin Determining the Installation Height se Wood Stud Installation Throw Distance Calculation Projector Installation Attaching the Mount Carriage ee ee Multiple Mounting Point Installation Single Mounting Point Installation Attaching the Mount Carriage to the eae Arm Cable Routing Optional Securing the Projector Optional Mount Adjustment n Technical Specifications Warranty Disclaimer OWDDMMRWWNND Mma E DONAKRRWNO Weight Capacity THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE Maximum projector weight 25 Ibs 5 TIMES THE WEIGHT OF THE PROJECTOR IF NOT THEN THE WALL STRUCTURE MUST BE REINFORCED Warning Statements aa PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INST
4. height and throw distance the mount carriage must be mounted to the projector Refer to the projectors User s Manual to determine the offset of the projector lens to the top of the screen whiteboard B j j Projector Lens Measure distance from center of lens to the top of the mount carriage C Add the distance from the ground to the top of the screen A Add the projector manufacturers recommended offset from the projector manual B Add the measurement from Step 1 C and then add the mounting screw offset D to the total Example A B C D Add the measurements to determine the mounting height mark Place a mark at the top of the total calculated height measurement starting from the ground up This height mark will determine your mounting points E Top of Screen gt Legend screen whiteboard viewable area measurement This measurement will be listed in the Users Manual A projector bracket the calculated total Proceed to the Wood Stud Installation section Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 5 gt 4 22 EST150 Wood Stud Installation Do NOT over tighten lag bolts when attaching the mount to the wall Improper installation may result in personal injury or damage to property THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND
5. independently by turning the leveling barrels Secure the legs to the mount carriage by screwing M6 x 12mm security screws into the M6 square nut do not overtighten on the mounting legs Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the mount carriage If the M6 square nut is not aligned with any slot you Installation Instructions can use any thin implement such as a toothpick to nudge it into alignment Mounting Hardware M3 Washer Leveling Barrel Cutaway View Side to Side Center of Gravity Front to Back Center of Gravity Visit the Premier Mounts website at http www premiermounts com Sliding M6 Square Nut Page 11 EST150 1 Tighten the mounting screws which secures the mounting legs to the projector Do not overtighten the mounting screws 1 Insert one 1 Barrel Cap except for the security barrel into the end of each leveling barrel Go to the Attaching the Mount Carriage to the Projector Arm section on page 15 Single Mounting Point Installation A single 4 20 x 5 16 screw must be used to attach the mount carriage to the projector if your projector has only one mounting point A Do not overtighten the 20 x 5 16 screw Proceed to the Attach
6. Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 3 gt 4 EST150 The Single Stud Short Throw Projector Wall Mount EST150 is a simple and elegant tool for mounting a wide variety of short throw projectors Its design allows you to use the same mount even if you need to replace the projector with a different model Unique features include a mount carriage that easily slides along the projector arm for quick screen size adjustments integrated cable management and Lock It security screws and barrel for enhanced security Single Stud Mounts firmly to a single wood stud Projector Adjustment Position the projector anywhere along the projector arm Cable Routing Discreetly manage signal and power cables through the projector arm Radial Glide Up to 6 of smooth adjustment in any direction EST WP Optional The optional EST WP wall plate allows for mounting to 12 or 16 dual studs The back plate also allows lateral shift after installation Page 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions EST150 22 Determining the Installation Height A Distance from ground to the top of the B Manufacturers recommended offset C Center of the lens to the top of the D If single stud EST150 add 5 14 to This total distance will be the location for the lower mounting point In order to determine the installation
7. RUCTIONS SHOULD BE READ AND COMPLETELY UN DERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE mm PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR STOP PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR P MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS STOP SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER DPE P OOE SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the projector If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in all Cutting drilling into an electrical line may cause serious injury Make sure there are no water lines inside the wall where the mount is to be locate
8. d Cutting drilling into a water line may cause severe water damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www premiermounts com Installation Instructions EST150 24 Installation Tools The following tools may be required depending upon your particular installation They are not included A Drill Bit Electronic Stud Finder Phillips Screwdriver Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 EST150 Hardware Projector Arm Projector Arm Mount Carriage Qty 1 Cover Plate Qty 1 5 Qty 1 d M3 Flat Washer M2 5 x 8mm M2 5 x 10mm M3 x 16mm M4 x 12mm M5 x 10mm Qty 4 Security Screw Qty 4 Security Screw Qty 4 Security Screw Qty 4 Security Screw Qty 4 Security Screw Qty 3 a M5 x 12mm M6 x 12mm Security 14 x 2 Wood Screw Ye20 x 5 16 Security M5 Security Wrench Barrel Cap Security Screw Qty 4 Screw Qty 4 Qty 2 Screw Qty 1 Qty 1 Qty 4
9. g Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJEC TORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPON SIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM AGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing
10. gle Mounting Point Installation section on page 14 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9 EST150 1 Locate the projector s mounting points 2 Position the mounting legs on the projector The mounting legs are pre installed Depending on the requirements of your projector you may remove one of the mounting legs The number and placement of mounting points on projectors varies between projector manufacturers Refer to you projector s technical specifications for the number and location of the mounting points on your specific projector Attach the mounting legs to the projector using the corresponding mounting hardware A Do not tighten the mounting hardware at this time Screws shown for illustration purposes only If the mounting legs need to be leveled rotate the leveling barrels to level the mounting bracket To raise the mounting legs rotate the leveling barrel clock wise To lower the mounting leg rotate the leveling barrel counter clock wise Raise or lower each of the mounting legs by rotating the leveling barrels until all of the mounting legs are at an equal height Lower the mounting leg by rotating the leveling barrel counter clockwise Raise the mounting legs by rotating the leveling barrel clockwise 3 When the desired position is achieved tighten the mounting screws to the p
11. ing the Mount Carriage to the Projector Arm section on page 15 Page 12 Visit the Premier Mounts website at http www premiermounts com Installation Instructions 4 EST150 CA Attaching the Mount Carriage to the Projector Arm Insert and slide the mount carriage along the projector arm to the desired position Shown with optional EST WP dual stud plate Projector not shown Once you have the desired position use one 1 M5 x 10mm security screw to tighten the mount carriage in place M5 x 10mm Security Screw Proceed to the Cable Routing Optional section on page 16 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 13 gt 4 cD EST150 Cable Routing Optional 1 Remove the plastic cover s from the cable routing openings 2 Route cables and wiring through the openings then out the back or bottom near the wall Proceed to the Securing the Projector Optional section Plastic Cover Route cables and wiring through the projector arm openings then out the back or bottom near the wall Securing the Projector Optional Your EST150 includes one 1 Security Barrel which can provide additional theft deterrence for your projector Shown below are two examples of how you can use the security barrel to make your projector installation more secure the PCB CSL1 Security Cable sold separately or padlock combination or keyed sold separately Follo
12. ng the upper mounting bracket The correct throw distance the distance from the projector to the screen must be determined prior to mounting the projector Refer to the projectors User s Manual to determine the distance from the lens to the front of the screen X Measure the distance from the front of Calculations the lens to the center of the projector Y X Manufacturers recommended throw distance Measure the distance from the wall to the gt _ Distance from wall to face of face of the whiteboard screen Z whiteboard screen Front Lens Add all measurements X Y Z to determine projector placement on the Front Lens Throw Distance arm assembly This measurement X Y Z will determine where the center of the mount bracket will be located on the Rear Lens Throw Distance arm assembly Please make note of this X Y Z measurement The EST150 can be also used as a wall mounted standard projector mount as well as a short throw projector mount Align the projector facing the opposite direction from the wall plate to project the image Rear Lens across the room Please take into account the projectors throw capabilities prior to mounting in the projector opposite direction Proceed to the Projector Installation section Projector Installation Attaching the Projector to the Mount Carriage Locate the mounting points on the bottom of the projector see arrows Proceed to the
13. rojector and then tighten the hex head leg screws with the M5 Allen wrench Page 10 Visit the Premier Mounts website at http www premiermounts com Installation Instructions EST150 1 Mounting Hardware Too Long WJ The depth of some projector mount points may prevent you from tightening the M2 5 and M3 mounting hardware You can reduce the length of the M2 5 and M3 mounting hardware by stacking up toa maximum of five 5 M3 flat washers inside the leveling barrel Avoid stacking too many M3 washers the mounting hardware must thread into the projector mount point at least four 4 complete turns Identify the projector s approximate front to back center of gravity Place your hands on each side of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from front to back Mentally note the apparent center of gravity Identify the projector s approximate side to side center of gravity Place your hands on the front and back of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from side to side Mentally note the apparent center of gravity Make sure the mount carriage is as close as possible to the projector s center of gravity Position the legs accordingly for best configuration You may raise or lower each leg
14. to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE DIXA CULA Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Page 16 Visit the Premier Mounts website at http www premiermounts com Installation Instructions
15. w the instructions below to install and secure the security barrel Determine which leveling barrel will be removed Remove the mounting screw Remove the leveling barrel by turning the leveling barrel counter clockwise Thread in the security barrel clockwise Insert and tighten the mounting screw Attach theft deterrent device PCB CSL1 or padlock through the hole that is on the security barrel Proceed to the Mount Adjustment section on page 17 Padlock Combination or Keyed Page 14 Visit the Premier Mounts website at http www premiermounts com Installation Instructions EST150 Mount Adjustment After the projector has been installed the projector must then be adjusted To adjust the projector 1 Loosen the M5 set screw using the M5 Allen wrench both sides 2 Adjust the projector to the correct position Firmly grasp the projector in both hands and tilt either forward or backward to adjust the level OR Firmly grasp the projector in both hands and rotate side to side for orientation adjustment Tighten both M5 set screws using the M5 Allen wrench Technical Specifications All measurements are in inches mm Installation Instructions Visit the Premier Mounts website at http www premiermounts com M5 Set Screw Page 15 gt 4 cD EST150 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Lon
Download Pdf Manuals
Related Search