Garage Door Remote Control Model KN-318
Contents
1. Console for 10 seconds until the PROG icon appears on the display 2 Press the PROG button again until the Q icon appears on the display 3 Activate the keypad transmitter For example 0000 for single door operation or 0000 Door Number for multiple door operation If a remote is programmed the Ry icon will stay on Remote Icon If additional remote needs to be programmed press the up button t the icon will flash again you may program additional remotes 5 INSTALLATION You can mount the keypad transmitter on a desired location with the screws provided Undo the screw from the bottom of the case Remove the back cover from the keypad Secure the back cover on a desired location with the screws Re install the keypad unit to the back cover Tighten the screw at the bottom of the case 6 TROUBLE SHOOTING Q Door opener does not react after pressing the button on the keypad transmitter A Ensure you hear 3 beeps from the keypad transmitter after entering the Password or Password Door Number for multiple door operation If you don t hear 3 beeps that means you have entered the incorrect password Re enter the password Ensure the keypad transmitter has been programmed to the Smart Button or garage door opener Refer to section 4 for how to program a keypad to the receiver 7 REMOVE THE KEYPAD TRANSMITTER FROM THE GARAGE DOOR RECEIVER You can delete the2. ANTY If within one year from date of purchase this product should become defective due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 13 CUSTOMER SERVICE If you would like to order Skylink s product or have difficulty getting your Skylink remote control to work or download information and user manual please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com P N 101Y106 are registered trademarks of their respective corporations 2013 SKYLINK GROUP
3. Garage Door Remote Control Model KN 318 1 INTRODUCTION Congratulations on your purchase of the Skylink Garage Door Remote Control Model KN 318 The Model KN 318 works with the Skylink Garage Door Receiver such as Smart Button and EQ IQ Garage Door Opener In this package you will find a keyless entry transmitter with screws Garage Door 2 pcs M3 5 x 20 screws Remote Control 2 OPERATING MODES SINGLE DOOR FACTORY DEFAULT SETTING The KN 318 can operate single Skylink garage door openers or single garage door opener receiver Smart Button This is the factory default setting If you plan to operate only one garage door opener or receiver proceed to Section 4 of this instructions to program the keypad KN 318 to the receiver MULTIPLE DOORS If you have multiple Skylink garage door openers or Smart Button receivers you can also set it up to operate multiple doors maximum up to 4 doors If you plan to operate multiple doors please refer to Section 3 below to setup your KN 318 to Multiple Door Operating Mode 3 MULTIPLE DOORS OPERATION ENABLE DISABLE THE MULTIPLE DOOR OPERATING MODE Model KN 318 can operate multiple Skylink garage door openers or multiple Smart Button Receivers It can operate up to 4 receivers To setup the KN 318 to operate multiple garage door openers or receivers please follow the instructions below 1 Enable the Multiple Door Operating Mode by entering the current password then p
4. keypad transmitter s from the garage door receiver Refer to the manual of the garage door receiver to erase the keypad transmitter 8 CHANGE PIN Follow the instructions below to change the PIN To change your PIN 1 Enter the current PIN factory default PIN 0 0 0 0 press 2 Enter new 2 to 8 digit PIN press 3 Enter new PIN again press For example if you are changing the PIN number from 0000 to 123456 enter the following sequence 0000 123456 123456 If the Keypad emits 3 beeps your pin has been successfully changed If the pin is different from step 2 the keypad will emit a long error beep and you have to re start from step 1 9 BATTERY One 1 5 volt Alkaline type AAA size battery required It is time to change the battery when the backlight no longer appearing 10 WARNING DO NOT let children use the garage door transmitter without adult supervision Children can injure themselves or others by the garage door 11 FCC The Garage Door Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules Its operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user s authority to operate the equipment 12 WARR
5. ord is accepted you will hear 3 beeps Before programming the keypad KN 318 to the garage door receiver you must decide which operating mode and which door you need to operate Follow the instructions below to program the keypad transmitter I PROGRAM KEYPAD TO SMART BUTTON 1 With the Smart Button connected on your existing wall button The red light on the Smart Button should flash after plugging in the power If the red light on the Smart Button is flashing slowly that indicates it is in standby mode 2 Press the learn button on the side of the Smart Button 3 Once the learn button is pressed the red LED will flash quickly You may release the learn button 4 Enter the default PIN 0000 or 0000 Door Number for multiple door operation within 5 seconds 5 Once the keypad transmitter is programmed the red LED will flash slowly in the same way as it flashes in standby mode Learn Button II PROGRAM KEYPAD TO EQ GARAGE DOOR OPENER 1 Press the Learn button on the EQ garage door opener yellow LED will flash for 30 seconds 2 Within 30 seconds activate the keypad transmitter For example 0000 for single door operation or 0000 Door Number for multiple door operation 3 Once the keypad is programmed the yellow LED will be off Learn and Set Button LED yellow LED red II PROGRAM KEYPAD TO IQ GARAGE DOOR OPENER 1 Press and hold the PROG button on the LCD Wall
6. ress Factory default password is 0000 2 Press 9 you will hear 2 beeps to confirm you have enabled the Multiple Door Operating Mode If you would like to disable the Multiple Door Operating Mode follow the steps below 1 Disable the Multiple Door Operating Mode by entering the current password then press Factory Default password is 0000 2 Press 0 you will hear 2 beeps to confirm you have disabled the Multiple Door Operating Mode OPERATIONS When you are in Multiple Door Operating Mode you can operate up to 4 garage door openers You need to program the 4 unique signals to the 4 receivers or door openers you plan to operate Password 1 Password 2 Password 3 Password 4 To send the signal for door 1 enter To send the signal for door 2 enter To send the signal for door 3 enter To send the signal for door 4 enter SS SS eS Ee You need to program these signals to the Skylink garage door openers or Smart Button in order for the KN 318 to operate them properly Please refer to section 4 to program the KN 318 Keypad to these receivers 4 PROGRAM A KEYPAD TO A GARAGE DOOR RECEIVER To operate the door under Single Door Operating Mode press Pass word factory default password is 0000 To operate the door under Multiple Doors Operating Mode press Password Door Number where Door Number can be 1 2 3 or 4 Factory default password is 0000 If the passw
Download Pdf Manuals
Related Search