GPRS Tau User Manual En - Inova
Contents
1. a validation check is performed If there is invalid data in one or more fields they will be colored in red Additionally under the button Save Config a field will be generated Error List which describes in details the errors and how to fix them If all the input data are correct GPRS Tau will save the parameters and will reboot with the new configuration Inova bg Ltd 2012 Page 16 of 20 GPRS Tau User Manual v1 0 5 Username and password configuration Inova bg Ltd GPRS Tau GPRS amp Ethernet Security Login Configuration Device Config _ This page allows to configure Login Username and Password Login Config CAUTION You will need this information to access this page Use the Hard Reset button if you can t remember your Login information After Reset default Username and Password will be recovered Reboot Default Username root Password admin CAUTION Enter desired configuration and click Save Config This will cause the device to reboot with the new settings Enter the new Login settings below maximum 11 symbols Copyright 2012 Inowa bg Ltd In Login Config menu you can change the username and password used to access the web server Maximum length for both fields is 11 symbols If you forget your credentials you can perform a hardware reset to recover default settings Username root Password admin When you click the Save Config button a validation check is performed If there is invali2. is wrong on the Home page this information will be shown In that case a field for new PIN code will be shown on this page GPRS Current Status GPRS Operator Not connected GPRS Signal No signal Peery ere SIM PIN required J Wrong FIN code SIM PIN required SIM PUK required Wrong PUE code PUK code New PIN code Submit If the PIN code is incorrectly entered 3 times a PUK code will be requested GPRS Tau automatically recognizes this case and a field for the PUK code will be shown along with new PIN code field on the Home page Inova bg Ltd 2012 Page 19 of 20 GPRS Tau User Manual v1 0 9 Windows Network configuration If you want to access the web server your computer must be in the same IP subnet You must change the settings of your network adapter if they are different than needed If your computer is in a different network than 192 168 1 xxx with mask 255 255 255 0 you will need to change your current configuration of Windows network Start gt Control Panel gt Network and Sharing Center gt Change adapter settings gt Right Click on your network adapter gt Properties gt Right Click on Internet Protocol Version 4 gt Properties gt Use the following IP address IP Address 192 168 1 xxx xxx is between 2 and 254 and must be different than 230 Subnet Mask 255 255 255 0 Inova bg Ltd 2012 Page 20 of 20
3. settings Obtain an IP address automatically via DHCP IP address is received automatically from a DHCP server in the current network If you select this mode but after reboot the device cannot find a dhcp server for more than 10 seconds GPRS Tau will load the last saved static address In this case easy way to access the web server is by entering the following address http gprstau Use the following IP address IP address and network parameters are set to static IP Address IP address Gateway Gateway address Subnet Mask Subnet mask of the IP network Inova bg Ltd 2012 Page 10 of 20 GPRS Tau 4 3 Server settings Server 1 Settings Type Use IP communication _ IP Address 914 211 189 253 W Use Periodic Test on Server 1 Test Period 10 Sec Server 2 Settings i Enable Server 2 Type Use IP communication ae Use IP communication en Use GPRS communication Port Use IP f available and GPRS as backup Use Periodic Test on Server 2 5 Mlin User Manual v1 0 GPRS Tau can work with two independent IP servers The first group is corresponding to the first monitoring server The field Type sets the type of communication which must be used to connect to the server IP network GPRS network IP network 1f available and GPRS as a backup 1f IP fails This option is a good way to minimize the GPRS traffic IP address and the communication UDP port must be set Periodic tes
4. 2 Page 8 of 20 GPRS Tau User Manual v1 0 Inova bg Ltd GPRS Tau GPRS amp Ethernet Security GPRS Tau Configuration Device Confi 5 This page allows to configure GPRS Tau network settings Login Config About z gt Device Name GPRS Tau Reboot Using communicator with Ademco Contact ID i Not using communicator _ Protocol Inova bg Tau LARS over IP System 01 fe Account Number TTT Send message if DC is lower than 10V System System number must range 00 to 03 It is used in Inova bg Tau for compatibility with KP LARS protocol Account Number Site s number If working with Inova bg Tau protocol first three symbols must range O to 7 and the last symbol must range 0 to 9 or A to J In the monitoring software the last symbol can be set as a digit or letter the digits 0 to 9 correspond to the letters A to J If working with Ademco Contact ID protocol each of the four symbols must be from 0 to 9 and or from B to F Send message if DC is lower than 10V Option that enables disables generating of message if the input voltage drops under 10V Inova bg Ltd 2012 Page 9 of 20 GPRS Tau User Manual v1 0 4 2 General IP settings Obtain an IP address automatically via DHCP Use the following IP address _ IP Address 192 168 1 230 Gateway 192 168 1 1 Subnet Mask 955 955 255 IP
5. GPRS Tau User Manual v1 0 Inova bg Ltd GPRS Tau Inova bg Ltd 2012 GPRS Tau User Manual v1 0 Table of contents l 2 3 4 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 Se ee Ge A MID AS AUS As 3 Start Working with CO PRS Tia 5 Home a Esa 6 Contisurationmot the mam parame lets ES MERS En SR ER esate At ne actina dee ee 8 General Cline cordel della 8 TC iN are ctl te eet nce cance at ne nate ea cee samen dicate ene dine een eat AEE 10 DEVEL SOUIN OS a ncean Aste a tatuaact ewe ahumnalvaaataeiias tastuaaduculu ty uaabsanu seeds uitaeadculusyomautenniens 1 CPR SR Nan O 12 PENTOUDULS TNES satis lili lr 13 A AePOr PP ae be needa anette connate E 14 Senes tor the distal la ladies 15 save the NSW COMM OU AM OM asic D se rss code den cie ae desserte ete te ae tennis e con 16 Username and password CONSUL ION sen redemande ets 17 R DOORE nl li 18 CATIA load 18 romo PIN Cod PUR CO ra ias 19 Windows NetWork CON SUTAON iii iii 20 Inova bg Ltd 2012 Page 2 of 20 GPRS Tau User Manual v1 0 1 Main features GPRS Tau is a communication device with the main purpose to transmit data from security panels and or sensors through GPRS and or IP based network Combining the advantages of those two advanced communication technologies GPRS Tau provides the most secure connection with monitoring center Features e Power supply 12VDC 8 5V to 16V e Low power consumption e Capability to use communicator as input using Ad
6. Welcome to GPRS Tau home page Device Config e Login Config Device Information Device Name GPRS Tau About o Account number 01 777 Device MAC 00 04 A3 4F 00 00 Reboot Firmware version 0 9 Power Supply DC Voltage 14 2V Last 5 Received Ademco Messages Last Message none Message 2 none Message 3 none Message 4 none Message 3 none Digital Input Current Status Digital Input 1 High Digital Input 2 High Digital Input 3 Not Used Digital Input 4 Not Used Digital Input 5 Not Used Digital Input 6 Not Used PGM Output Current Status PGM Output Not Used GPRS Current Status GPRS Operator M TEL GSM GPRS Signal ssses 77 dBm Initializating Checking SIM SIM PIN OK Searching for network GPES netrork connected Copyright 2012 Inowa bg Ltd Inova bg Ltd 2012 Page 6 of 20 GPRS Tau User Manual v1 0 On the homepage you can find main information about the device current status of the input voltage last 5 messages received from the communicator current state of each digital input PGM state GPRS status information about the operator and the signal strength Through the menu you could select one of the following actions Home Homepage Device Config Configuration of the main parameters Login Config Configuration of username and password for web server access About Contact information Reboot Restart the device Inova bg Ltd 2012 Page 7 of 20 GPRS Ta
7. d data in one or more fields they will be colored in red If all the input data are correct GPRS Tau will save the parameters and will reboot with the new configuration Inova bg Ltd 2012 Page 17 of 20 GPRS Tau User Manual v1 0 6 Reboot O Z al O ije a a GPRS Tau GPRS amp Ethernet Security Home a dd Device is rebooting Device Confi a Your settings were successfully saved and the device is now rebooting to Login Config configure itself with the new settings Your board is now located at http 192 168 1 230 About Reboot Copyright 2012 Inowa bg Ltd If you choose the Reboot menu this will cause the device to restart 7 Hardware reset In case you changed the settings and can t reach the device or 1f you forgot your username or password GPRS Tau is capable to return to its factory defaults For this purpose you must disconnect from power supply push and hold the button for hardware reset and reconnect to the power supply Hold the button for 5 seconds until the green LED is blinking Once the LED goes off you can release the button and connect to the device Inova bg Ltd 2012 Page 18 of 20 GPRS Tau User Manual v1 0 8 Wrong PIN code PUK code GPRS Current Status GPRS Operator Not connected GPRS Signal oe No signal Initializating Checking SIM SIM PIN required Wrong PIN code Enter PIN code Submit If the PIN code entered in Device Config menu
8. emco Contact ID protocol e Six digital inputs working simultaneously with GPRS and or IP transmitters e HTML server for easy configuration and status check protected with an username and a password e Easy configuration without the need of specialized software for programming using only a web browser Internet Explorer Google Chrome Firefox etc e Capability to use one or two fully independent servers Additional option to use GPRS only as a backup in case the IP network fails e SMS report of the status of the communicator and or digital inputs to up to 5 mobile numbers Inova bg Ltd 2012 Page 3 of 20 GPRS Tau User Manual v1 0 e Capability every digital input separately to be set to transmit SMS report e PGM output controlled by SMS or call e Capability to enter PIN or PUK code for the SIM card e Graphical display of the status of the GPRS network in the web interface e Encrypted connection with IP servers e Verification with an unique ID code e Capability to change the username and password of the html server e Indication 4 LEDs for LAN Status Ethernet available LAN Activity Network packets service GPRS LED ON when connected to GPRS network Server LED Established connection with server s when using 1 server ON when connection is established When using 2 servers ON when connection is established with both servers blinks if connection is established with only one ser
9. onnected to PGM or dry contact for 0 state 1s accepted value of the resistance to ground less than 300Q and for active 1 value more than 1 4KQ or open circuit the hysteresis is between 300Q and 1 4KQ If digital inputs are controlled by voltage for 0 state is accepted value of the voltage to ground less than 0 7V and for active 1 value more than 2 6V the hysteresis 1s between 0 7V and 2 6V In the settings for each input you can set the following parameters Type Choose a message which will correspond to the change of state of this input Partition two symbols each from 0 to 9 and from B to F and Zone three symbols each from 0 to 9 and from B to F determines the corresponding parameters for the messages generated from each digital input If in SMS Reporting settings Reporting Type is set to From Digital Inputs or From Communicator and Digital Inputs then for each input a checkbox for reporting enable disable will be shown Report SMS from this input Inova bg Ltd 2012 Page 15 of 20 GPRS Tau User Manual v1 0 4 8 Saving the new configuration Digital Input 6 Settings Active State N C Type 401 Open Close by User o Partition 097 Zone 906 Report SMS from this input Error List 2 Server Port must range 1 65535 l DigitalInput6 partition must be Maximum 2 symbols Symbols must range 0 9 and or B F When you click the Save Config button
10. s received from the communicator e From Digital Inputs SMS report will be sent to each phone number only when alarm message is received from digital inputs To each digital input sms report can be enabled disabled separately e From Communicator and Digital Inputs SMS report will be sent to each phone number when alarm message is received from the communicator or digital inputs To each digital input sms report can be enabled disabled separately Inova bg Ltd 2012 Page 14 of 20 GPRS Tau User Manual v1 0 4 7 Settings for the digital inputs Digital Input 1 Settings Active State NC a Type 140 General Alarm o Partition 99 Zone 901 Y Report SMS from this input Digital Input 2 Settings Active State N C Type by User Dee 110 Fire Alarm REE 120 Panic Alarm ae 130 Burglary Alarm 133 24 Hour Alarm Report SMS fror 157 Tamper RE lela Aa A ON 440 General Alarm e A 301 AC Loss Digital Input 3 Setti 302 Low System Battery E 309 Battery Test Failure 400 Open Close 401 Open Close by User Digital inputs can be connected to PGM outputs of security panles or to any different kind of sensors panic buttons tampers and etc In the Active State field you can set the working mode of each input normal close N O or normal open N C contact check for AC on this input Hardware AC or you can disable the input Not Used When digital input is c
11. t can be activated by selecting the checkbox Use Periodic Test on Server 1 and then setting the test period If you want to use the second server you must enable it Enable Server 2 and to set the parameters in the same way as for Serverl Inova bg Ltd 2012 Page 11 of 20 GPRS Tau User Manual v1 0 4 4 GPRS settings GPRS Settings SIM PIN Code 0000 APN APN Username APN Password In the GPRS Settings the parameters of the mobile operator must be entered If only IP network is used these fields can be empty In SIM PIN Code the PIN code must be entered If the sim card doesn t use PIN code this field has no role empty or not APN Access Point Name APN Username APN Password are parameters of the mobile network The mobile operator must provide them Inova bg Ltd 2012 Page 12 of 20 GPRS Tau User Manual v1 0 4 5 PGM output settings PGM Output Settings PGM Activation Call or SMS from specific numbers o SMS report when PGM status is changed Mobile number 1 4359998123456 Mobile number 2 Mobile number 3 Mobile number 4 Mobile number 5 GPRS Tau has one programmable output PGM It can be used for remote controlling of different devices and processes PGM Activation sets the working mode of the PGM It can have the following values e Disable PGM Deactivates the output e Call or SMS from any number The output can be controlled with call or SMS from any phone n
12. u User Manual v1 0 4 Configuration of the main parameters 4 1 General settings Inova bg Ltd GPRS Tau GPRS amp Ethernet Security Home Device Config Login Config About GPRS Tau Configuration This page allows to configure GPRS Tau network settings Device Name GPRS Tau Reboot o Using communicator with Ademco Contact ID Not using communicator Phone Number g C Send message if DC is lower than 10V Device Name Enter the name of the device This value is used only for user convenience to identify devices if you have more than one connected to one network Maximum length 30 symbols Select working mode and protocol Using communicator with Ademco Contact ID In this mode the sixth input is used as a input for communicator on Ademco Contact ID protocol The site s number is received from the security panel Phone number must be entered Not using communicator In this mode the device is working without communicator and all the inputs can be used The phone number field is replaced with site s number and protocol selector fields The protocol can be Ademco Contact ID or Inova bg Tau The protocol Inova bg Tau sends Ademco Contact ID and KP LARS simultaneously That requires some restrictions on the site s number and additionally system number must be entered This protocol makes it possible to combine Radio GPRS and IP transmitters in one monitoring system Inova bg Ltd 201
13. umber When an incoming call is registered the output changes its state alternatively 1 to 0 and O to 1 If SMS with text ON is received the output state will be set to 1 and SMS with text OFF will set the state to 0 e Call or SMS from specific numbers The output can be controlled only by the five phone numbers that are entered When an incoming call is registered the output changes its state alternatively 1 to O and O to 1 If SMS with text ON is received the output state will be set to 1 and SMS with text OFF will set the state to 0 If the phone number which calls or send SMS is not one of the entered numbers the PGM status will not be affected SMS report when PGM status is changed Enables Disables SMS report when the PGM s state is changing After GPRS Tau change the PGM state it will send SMS to the number that initiate this action to confirm the changes Inova bg Ltd 2012 Page 13 of 20 GPRS Tau User Manual v1 0 4 6 SMS report settings _ SMS Reporting Settings Reporting Type From Communicator and Digital Inputs B Mobile number 1 4359999193456 Mobile number 2 Mobile number 3 Mobile number 4 Mobile number 5 SMS report can be sent to up to 5 phone numbers Reporting Type sets which of the signals to be sent as a SMS report e Disable SMS Reporting Deactivates the SMS reporting function e From Communicator SMS report will be sent to each phone number only when alarm message i
14. ver OFF when connection isn t established with both servers e Configurable working mode for every digital input Normal Open Normal Close Check for AC voltage from 5V to 20V Deactivated e Configurable parameters sent for events on each digital input to IP servers Inova bg Ltd 2012 Page 4 of 20 GPRS Tau User Manual v1 0 2 Start working with GPRS Tau The default IP address is 192 168 1 230 Make sure that your computer is in the same IP subnet see Chapter 9 Error Reference source not found To access the web server for onfiguration use Internet Explorer Chrome Firefox Opera or any other web browser and enter the GPRS Tau s address http 192 168 1 230 or the new one if you already change it Alternatively you could write http gprstau If the device is accessible from that computer a connection will be established and you will be prompt to enter username and password Authentication Required x The server 192 168 1 230 60 at Protected requires a username and password User Name root Password ss Cancel The default settings which will be recovered after hardware reset are IP Address 192 168 1 230 Username root Password admin If you enter the right credentials you will have access to the web page for configuration Inova bg Ltd 2012 Page 5 of 20 GPRS Tau User Manual v1 0 3 Homepage Inova bg Ltd GPRS Tau GPRS amp Ethernet Security detent
Download Pdf Manuals
Related Search