IES Energy User Manual
Contents
1. mode the master fader where the leds indicate the cross direction The green leds indicate the stored data the red leds the actual level send across the DMX 512 output PROGRAMMING A CUE load bank X There are 8 cue s available behind the faders of preset A To store these use the following steps Press load together with bank the point from the bank digit is on Make the desired light setting and press the flash button where you want to store this cue together with a pulse on the load button the matching led is on Repeat this for the other cue s When finished double click on the load button to leave this menu You can recall this cue b m o the corresponding fader or flash button The master level is controlled by the master fader if the master led is on The fade time is set by means of the speed fader 2002 IES BV Veenendaal 21 01 02 7 ENTERING A PATCH FIELD load step power X X X The Energy provides a possibility to enter a patch for the outgoing DMX channels to easily relocate you light fixtures To do so proceed as follows Press load together with step and power the 3 points in the bank and step display are on The step display now shows the DMX channel number and the bank display shows to which desk channel it is assigned Select the DMX channel which you would like to alter b m o the step button and assign the desk channel by2. ENERGY No 2 ea FUSE 400mA _ ae g sn IN MAINS INPUT DMX 512 230V 50 60Hz OUTPUT OPTION PORT 1 DMX 512 XLR output PIN un amp U I mm FUNCTION SHIELD RS 485 in Rs485 in COMPLEMENT COMPLEMENT 2002 IES BV Veenendaal SUB D CONNECTIONS Bank up 9p Sub D female Eo f 5 o T Slep up Ne 2 EE a Hold auto step X En i Black out rcp GND signal audio Input 0 5 50V 21 01 02 5 INTERNAL CONNECTIONS SrFACSCT IOAMMoOOWDY Memory EPROM 1MB EPROM which contains the main program version 1 11 78HC11 8Mhz processor board 40 pole Flat cable for communication between boards Pot for level speed and sound level Dipswitch 4 clears the memory EPROM Back up battery witch guaranties a reliable back up for over 3 months Power supply Mains input with 2 x fuse 400mA DMX 512 output 5 pole XLR Special sub d output for external control Device address setting 16 pole flat cable connector 16 pole flat cable connector 2002 IES BV Veenendaal 21 01 02 PRESET CONTROLS MANUAL MODE bank load step XX start up mode In manual mode the row of faders are controlling the individual channels for an independent cue In automatic mode these faders all contain a cue MASTER Sets the maximum level for preset A In automatic mode the master fader can also be used as a
3. dipless cross fader by switching the sound knob in cross position After a completed cross the bank step is incremented by one In this mode the level fader functions as a master level control FLASH BUTTONS Whilst pressed individual cue s or channels are flashed The flash level is controlled by means of the LEVEL fader PROGRAMMING A BANK chaser load step X X X The memory is capable of storing 10 chasers each containing 99 steps with a programmable end position The levels are real and can be controlled in total level b m o the level fader To enter a program the following steps should be followed Press load together with step the 2 points from the step digits are on Select the desired bank step number and make a light setting via the channel faders Store these settings by pressing load The step counter is now incremented by one Make a new light setting and press load once again If you have entered all steps press load for 3 seconds until the points are flashing to define a end marker By means of the step button it is possible to walk through the chaser to check the programmed steps To leave this program mode double click the load button within 1 second To recall a chaser turn the chaser on The speed can be controlled by the speed fader between 0 1 and 10 seconds To step manually switch the speed off and use the step button or in cross
4. bank number In patch mode it displays the channel number The button enables the speed G gt Step display 0 99 This shows the actual step number In patch mode it shows the DMX channel number were a desk channel number could be assigned to H gt Cue channel flash Whilst pressed individual stored cues are flashed in manual mode or when set by the internal dipswitch the channels are flashed l gt Master cross fader This fader has a double function In manual mode and when the audio knob is not in the position CROSS it functions as a master fader for fader 1 to 8 The M led now indicates the master status lf the cross mode is selected the A and B leds indicate the cross status EXAMPLE The step display shows 14 and the master is positioned on the top the A led is now full If the master now goes towards B cue 14 is recalled Led A is decreased and B is increased in intensity If the master is completely down the step counter is increased by one Sliding the master up these steps are repeated J gt Level fader This fader functions as a master for the sequencer It also allows the possibility to program a sequence during a performance by turning on the blind mode The present DMX output is now frozen In cross mode it functions as an overall master control K gt Speed fader Controls the step frequency and also the cross fade time When switched off only the step button can inc
5. pressing the channel flash button Leave this menu by a double click on the load button To recall the original setting press the load button for 2 seconds DESK SETUP To modify the functions of the energy to your own wishes press flash button 1 and load for 5 seconds By means of the bank switch you can select the flash functions BANK FUNCTION dunas flash button works as a channel flash default Ds flash button works as a cue flash in solo mode e PER E E flash button works as a cue flash in add mode The step button is now used to select the cross function STEP FUNCTION Doors cross time 0 0 sec The step frequency is set b m o speed The cue s are recalled with the stored levels This mode is mend for rock and roll use The total level is still controlled b m o the level master Matt cross time step time Use this setting for theatre lighting together with the step switch as a GO button default AA scanner mode levels are recalled as recorded 2th DESK SETUP Press flash button 2 together with load for 5 seconds to enter the second setup menu BANK FUNCTION Diao blind programming disabled default Me e blind programming enabled STEP FUNCTION Ao cross function off default PAANI cross function possible e EATON ATOE cross function possible master functions as a up down selection during entering a bank and a patch ALL CLEAR It is possible to reset the ENERGY to t
6. IES USER MANUAL ENERGY PROGRAM SECTION Y CoN wv BLIND LI F F OFF CROSS EVEL SPEED SOUND BANK LOAD STEP POWER TU exit MANUAL MODE PROG CUE PROG BANK ENTER PATCH 2002 IES BV Veenendaal 21 01 02 Issue 1 Software version 1 11 CONTENTS Content page A A IR EOIN SIAR ICS IN page Dimensions amp specifications oooococnccnnnncccccccnnnccnnnnnarrnccnnn cnn nnnn nro page External connections ooocononccccccccnnncononnnnnncnnnnnnnananonnncnnnncnnnnnnnnnno page Internal CONNECTIONS coooccccnncccoccccnnnconnnananoncnnnncnnnnnnn nn nccnnn rra nnnnnnnnno page PresetiCONtO S issin againne eh sa nenin gh ea sain namaa rennir Sasain ha iain page Programming a Dank ooocccccnncccocccccnncconnnannnncnnnncnnnnnnnn nn ccnnnncnnnnnnn nn page Programming a CUE 000 2 cece eeecceeeee cette eeeeeeaaaeeeeeeeeeeeeaaaeeeeeeeeeeeeeaaaes page Entering a patch field oooonnncncccnnnnccnnnnccoocccnnncnonnnnrrn cnn cnn cn nnnnn nro page DOSK SOTUP EE T page 2 Th desk SClUDP mm mm rm r r rm ri page A airi ai ai geir ga ei sara ghra nia gin ai ai gh agis iain ai Shea page Declaration of conformity oooonncooccccnnncccnnncanonccnnnccnnnnnnn nn ccnnnncnnannnn anno page IES International Electronics Service Wageningselaan 52 54 3903 LA Veenendaal The Netherlands Tell 31 0 318 555495 Fax 31 0 318 555661 www ies nl CAUTION O 0 00 0000 Y Y Y O 01 2 ON To preven
7. he original factory settings by pressing flash button 8 together with load for 5 seconds 2002 IES BV Veenendaal 21 01 02 8 IES I E S B V DECLARATION OF CONFORMITY According to ISO IEC Guide 22 Manufacturer s name I E S B V Manufacturer s address Wageningselaan 52 54 3903 LA Veenendaal Netherlands Declares that the product Product name ENERGY Model number ENERGY no 9603 Conforms to the following product Specifications Emission EN 50081 1 EN 50081 2 EN 55011 EN 55014 Immunity EN 50082 1 EN 50082 2 EN 55024 2 6 kV Contact discharge 8 kV Air discharge EN 55024 3 3V m EN 55024 4 1 kV Signal lines 2 kV Power lines Supplementary information The product complies with the EMC Directive 89 336 EEC Veenendaal December 2000 J H D de Jonge Technical Manager 2002 IES BV Veenendaal 21 01 02
8. rement a step L gt Audio fader The audio output is provided with an automatic gain control and the compression is adjusted by means of this fader Beneath 10 the audio input is still blocked In cross mode the audio input is ignore and the master now work as a cross fader 2002 IES BV Veenendaal 21 01 02 3 DIMMENSIONS amp SPECIFICATIONS 302mm PROGRAM SECTION BLIND OFF CROSS LEVEL SPEED SOUND BANK STEP 155mm BANK LOAD STEP POWER uit Supply voltage iriran aaa ccoo nn a apaa aaia aoi 230V 20 FOQUGIICY iv ir aapa i 50 60 Hz A siiin n taconite 8 patched over 96 DMX512 RINKS coi ida rie cea 10 Steps real lSVOl cion aa rai e 99 Fader CUGES moi ias 8 Weight ins iisipan aa a aa EE TEE E aaa aaae 1 4kg Protection ClASS iii tic IP20 Output level ooooooonnnnconnncconnnccnnncccnnoccconanncnanaccnnnnnnnnn DMX512 optical isolated Audio IMP t sko ean aoin aa tr a a a a 0 5 50V RMS Low voltage Cir Ctive ccceceeceeeceeeeesteeeeeeeeeesteeeeaaes complies to EN 60204 EMG GMISSION aiii complies to EN 50081 1 EMC immunity complies to EN 50082 2 EN 55024 2 4kV cd 8kV ad EN 55024 3 3 V m EN55024 4 2kV line 1kV signal 2002 IES BV Veenendaal 21 01 02 EXTERNAL CONNECTIONS fh Mh D I s P1 bank up P2 step up SUES I P3 hold 70 I I P4 black out MADE IN HOLLAND P5 GND C TYPE
9. t fire or shock hazard do not expose the unit in rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only WARRANTY We warranty each of our products to be free from defects in material and workmanship Our obligation under this warranty is to repair or replace any instrument or part thereof which within two years after shipment proves defective upon examination External influences are excluded To exercise this warranty write or cal IES representative or contact the IES service department You will be given prompt assistance and if necessary shipping instructions 2002 IES BV Veenendaal 21 01 02 FUNCTIONS Fm Ainm BANK LOAD STEP POWER A gt Channel fader Controls the level of an individual channel gt Bank selection Selects the desired bank sequencer Pressing load together with bank selects the cue program mode Pressing bank load step together sets the Energy in manual mode Cc gt Load button During a program mode stores the present cue set by the faders in row mentioned in point A A double click leaves the program mode D gt Step button Increases the present step by one Load pressed together with step selects the bank program mode E gt Power button Turns the desk on Pressing it for more then 2 seconds turns it off and shows 3 Points Pressing load together with power selects patch mode F gt Bank display 0 9 Shows the
Download Pdf Manuals
Related Search