IEPM-LC_SLU_usermanual
Contents
1. 65 130VAC Return 2 2 Line High 280VAC 2 140VAC 280VAC Transfer 2 2 Line High 260VAC 2 30 260VAC Return 2 2 200 220 230 240Vac DUM re settable pane Voltage 100 110 115 120Vac t Settable re settable via LCD panel panel Voltage Regulation 3 RMS for entire battery voltage Batt Mode range Frequency Regulation 0 1 7 Output Batt Mode Pure Sinewave Overload Circuit Breaker Protection Battery 110 150 for 30 sec Mode gt 150 for 200ms lt 8 ms 24 48V dc Transfer Time 20 32 42 62 Battery Backup Time at full load long time available Max Charging Current 3 steps selectable 60 80 100 Amp Battery Voltage ui ua INVERTER INVERTER 4000W 6000W 8000W Charge Vlotage 27 7V 55 2V Solar Maximum Peak Voltage 59 0 100 Solar LU E solar Charge Working 24 0 44 0N Maximum Charging Current Polarity Protect UPS status I P amp O P Voltage Frequency LCD Load9 Battery Voltage amp Charge current Temperature Mode Normal Green Warning Yellow Fault Red Battery Mode Beeping every 4 seconds Audible arm Audible Noise Less than 55dBA at 1M Net Weigh Kgs 49 2Kg 51 4Kg 55Kg Physical WxHxD mm XI1X Wall Mounted 415 600 260415 600 260 415 600 260 Specifications are subjected to change without prior notice 322. Inverter Charger In battery operation mode press it with Up key at the same time to disable the buzzer Beside it 1s pressed to confirm and enter the item selected Fault LED red To indicate the Inverter Charger is in fault condition because of inverter shutdown or over temperature Warning LED yellow To indicate the Inverter Charger 1s in the status of overload bypass and battery back up Normal LED green To indicate Inverter Charger 15 operating normally ON TEST MUTE key It should be pressed with the control key simultaneously to switch on Inverter Charger do auto test in normal AC mode and turn off the buzzer in battery operation 4 2 Description 800W Rack Mount 800W Wall Mounted 1600W 2400W Wall Mounted miw 1298 4 i W 288mm 4 150mm Hi400mm 4000W 6000W 8000W Wall Mounted Type E i W 418mm iDpiz mm 2 z IL iHi amp 0mm BREAKER 800W Wall Mounted Type Black case W 298mm BATTERY BATTERY INTELLIGET SOLT REMOTE CONTROL BREAKER 1600W 2400W Wall Mounted Type Black Case Ww 2988mm BATTERY SOLAR TERM 5 OPERATION 5 1 Check Prior to Start Up 1 Ensure the Inverter Charger 15 in a suitable positioning 2 Check input cord is secured 3 Make sure
3. fault 5 Fan is damaged 2 Replace the fan LED lits up Buzzer beeps 3 Unknown 3 Restart continuously AC utility power is normal Overload Please reduce the but Inverter Charger is 100 lt load lt 125 critical load to lt 100 overloaded Warning LED lits up and buzzer beeps per second AC utility power is normal Overload Please reduce the Warning LED does not 125 lt load lt 150 critical load to lt 100 fade out and buzzer beeps per 0 5 second AC utility power is normal Overload Please reduce the Warning LED lits up and 150 lt load critical load to lt 100 buzzer beeps continuously 22 UPS STATUS POSSIBLE CAUSE AC utility power fails The 1 AC utility power load is supplied by battery failure power Buzzer alarm sounds gt input connection every 4 seconds may be not correct AC utility fails Inverter Battery power 1s Charger is in battery backup approaching low level mode Buzzer alarm beeps every second AC utility power fails Battery runs out Inverter Charger has shut down automatically 26 ACTION 1 Reduce the less critical load order to extend backup time 2 Please check the rated input or connected line Inverter Charger will shut down automatically Please save data or turn off the loads soon Inverter Charger will restart up when AC utility power 15 restored 7 OPERATION MODES 7 1 Inverter Charger System Blo
4. to AC INPUT HIGH LOW VOLTAGE Remark Low voltage 110V system Range 60 100 220V system Range 120V 200V High voltage 110V system Range 125 140 220V system Range 250V 280V 18 5 8 OUTPUT VOLTAGE AND FREQUENCY ADJUSTMENT SETTING After startup press the V in the middle and stop at VOLT FREQ SET Press the ENTER key lt at right arrow will appear at bottom before 100 VAC Press the V amp key to adjust the output voltage Press the ENTER key lt again the arrow will switch the position before SOHZ or 60HZ Press the V amp A key to adjust the output frequency After finishing setting press the ENTER key lt and move to save option 19 Press V key and switch NO to YES at save function and then press the ENTER key lt again to save Now we complete the setting for OUTPUT VOLTAGE AND FREQUENCY ADJUSTMENT Remark Four setup values for 110V 100V gt 115V 120V Four setup values for 220V 200V 220V 230V 240V Two options for frequency change 50HZ 60HZ 20 5 9 LOW VOLTAGE SHUTDOWN SETTING After startup press the V in the middle and stop at BAT SHUT Press the ENTER key lt at right the arrow will then appear between BAT SHUT and MIDDLE Press the V amp A key to set up the voltage value for shutdown protection After finishing setting press the ENTER k
5. 1 5 5 GREEN POWER SETTING After the startup screen the LCD will display the main menu as shown in the photo Press the V key in the middle continuously until seeing the same display as shown in the photo Then press the enter key at right and there will be a cursor shown between SETTING and AC TO AC Press enter key again so the cursor will move down to the position between GREEN and OFF 12 13 Press V key in the middle once the LCD Display shall now display GREEN ON 30sec Press the enter key at right again and the cursor shall move to the right and now pointing 30sec There are 4 options 15sec 30sec 45sec 60sec for how often to run the detection After completing the setting press the enter key at right The LCD Display shall display FUNCTION SETTING SAVE NO as shown photo Press the V key in the middle the text shall now become YES then press the enter key again to confirm the setting Remark The same screen as shown in the photo shall be displaying and the inverter will automatically run the detection on GREEN POWER every 30 Sec When AC IN source is connected the Normal LED will light up when AC IN source is not connected the Warning LED will light up 14 5 6 DC TO AC SETTING After startup we can change the LCD display by the A amp V key Press the V key till you see the display sho
6. C 2 130VAC 2 OC H B re settable via LCD pane Voltage 100 110 115 120Vac re settable via LCD panel Voltage Regulation lt 3 RMS for entire battery voltage Batt Mode range Frequency Regulation Batt Mode Output 80 Circuit Breaker Overload Protection Battery 110 150 for 30 sec gt 150 for Mode 200ms Battery Voltage 60 3 2 Battery Backup Time at full load long time available Max Charging Current 3 steps selectable 60 80 100 Amp Battery Voltage Charge Vlotage 27 7V Solar Maximum Peak Voltage 59 0 Solar Charge Working M 24 0 Charging Back Flow Protect Model S an INVERTER INVERTER 1600W 2400W Solar Charge SLU UPS status I P amp O P Voltage Frequency LCD Battery Voltage amp Charge current Temperature Mode Normal Green Warning Yellow Fault LS Battery Mode Beeping every 4 seconds Audible arm nip ow oa B 298 400 150 298 450 190 298 450 190 Specifications are subjected to change without prior notice 30 INVERTER INVERTER INVERTER 4000W 6000W 8000W 5 6 SKVA V Watt 4000W 6000W 8000W Nominal Voltage 220Vac 110Vac 220Vac only Acceptable Voltage 120 280Vac 60 140Vac 120 280Vac Range SOHz 50Hz 60Hz 45Hz 60Hz Input 70Hz e Voltage Line Low 120VAC 2 60 120VAC Range Transfer 2 2 Line Low 130VAC 2
7. ck Diagram 7 2 Normal Operation AC Priority There are two main loops when AC utility 15 normal the AC loop and the battery charging loop The AC output power comes from AC utility input and passes through static switch to support power to load The battery charging voltage comes from AC utility input and converted by AC DC charger to support battery charging power 7 3 AC Utility Failure Battery Mode The AC output comes from battery passing through DC AC inverter and static switch within the battery backup time 27 7 4 Normal Operation DC Priority The AC output comes from battery passing through DC AC inverter and static switch within the battery backup time INVER TRE 7 5 DC Utility Failure Out Of Battery Mode The AC output power comes from AC utility input and passes through static switch to support power to load The battery charging voltage comes from AC utility input and converted by AC DC charger to support battery charging power AL CTP AL INPUT please refer to 17 5 6 DC to AC SETTING 28 SPECIFICATION INVERTER INVERTER INVERTER 800W 1600W 2400W 12KVA 2 4KVA 3 6KVA Capacity VA Watt 800W 1600W 2400W Nominal Voltage 220Vac 110Vac Acceptable Voltage 120 280Vac 60 140Vac Range SOHz 60Hz 45Hz 70Hz Input 120VAC 2 60VAC 2 Range Tine L 130VAC 2 65VAC 2 p 280VAC 2 140VAC 2 260VA
8. ey lt and move to save option 21 Press V key switch NO to YES at save function and then press the ENTER key lt again to save Now we complete the setting for setup value to BATTERY LOW VOLTAGE SHUTDOWN Remark Three different setup values for low voltage shutdown protection HIGH 42V MIDDLE 40V LOW 38V Default Value MIDDLE 40V 22 5 10 BATTERY CHARGE CURRENT SETTING After startup press the V in the middle and stop at the CHG CURR display Press the ENTER key lt at right the arrow will then appear between BAT SHUT and MIDDLE Press the ENTER key lt again the arrow will switch to bottom between CHG CURR and MIDDLE Press the V amp A key to set up the charging current 23 After finishing setting press the ENTER key lt and move to save option Press the V key switch NO to YES at save function and then press the Enter key lt again to save Now we complete the setup value for BATTERY CHARGING CURRENT Remark Three different setup values for battery charging current HIGH 100A MIDDLE 80A LOW 60A Default Value MIDDLE 80 24 6 TROUBLE SHOOTING GUIDE 6 1 For LCD Model The following guideline may be helpful for basic problem solving No UPS STATUS POSSIBLE CAUSE ACTION AC utility power is normal 1 Charger PCB is Replace the charger Inverter Charger 15 damaged PCB running normally but
9. innovative energies LC Series 800W 8000W SLU Series 800W 8000W LCD Display Pure Sine Wave Inverter Charger ati ae l eu eto USER MANUAL L f Innovative Energies Ltd 1 Heremai Street Henderson 2 Tel 64 9 835 0700 info innovative co nz CONTENTS LINTRODUC SELON 1 2 SAFTY INSTRUCTION 3 3 CABLE CONNECTION 4 4 SYSTEM DESCRIPTION 5 JOPERA HON TN 9 6 TROUBLE SHOOTING GUIDE 25 17 OPERATION MODES vse 27 BOF BOLE IC Ne 29 1 INTRODUCTION 1 1 General Description The Inverter Charger solar charge controller as optional a powerful all in one solution delivers unsurpassed clean true sine wave output power and combines this with a selectable multistage battery charging current Applicable for any kind of loads such as air conditioner home appliances consumer electronic and office equipments This series features a durable amp continuous 24 operation The built in 5 stage intelligent charger automatically charges any type of batteries without the risk of overcharge The compact amp modular design makes utility interactive installations easier and more cost effective It 1s a high quality product that offers the best price performance ratio in the industry 1 2 Key features 1 Multiple microprocessor design base Compatible with both linear amp non linear load S
10. n 1 The system may be installed and wired only by qualified electricians in accordance with applicable safety regulations 2 When installing the electrical wiring please note the nominal amperage of your incoming feeder 3 Inspect the packaging carton and its contents for damage Please inform the transport agency immediately should you find signs of damage Please keep the packaging in a safe place for future use 3 2 Connection 1 Inverter Charger Input Connection If the Inverter Charger is connected via the power cord please use a proper socket with protection against electric current and pay attention to the capacity of the socket 2 Inverter Charger Output Connection The output of this model 15 with terminal block Simply wire the load power cord to output terminal to complete connection 4 SYSTEM DESCRIPTION 4 1Front Panel Description for LCD Model LCD Display This indicates Inverter Charger operation information including UPS status input output voltage input output frequency battery voltage battery capacity left output load inside temperature and the times of history events Up key Use to select upward the Inverter Charger status on LCD Display Down key Use to select downward the Inverter Charger status on LCD Display Beside press it simultaneously with the Up key to switch off the Inverter Charger Enter Key It 1s pressed with the Down key to turn on the
11. the load is disconnected or in the OFF position 4 Check 1f input voltage meets the Inverter Charger rating required 5 2 Storage Instruction Disconnect input power in rear panel if you will not use it for long period If the Inverter Charger 1s stored over 3 months please keep supplying power to the Inverter Charger for at least 24 hours to ensure battery fully recharged 5 3 Operation Procedure for LCD Model e Please follow the instructions below for Inverter Charger operation o 19 1 Once the AC source is connected the LCD Display shall light up immediately to display first the main menu of greeting context and the Normal LED 15 blinking to indicate ready to switch on the inverter 2 By pressing the Enter key and the Down key simultaneously for 3 seconds the Inverter Charger will start up after two beeps and Normal LED lights up to indicate the power is from its inverter to the load 3 When the Down key and the Up key are pressed simultaneously for 3 seconds the inverter will be turned off after two beeps and the Inverter Charger is on the standby status LCD display illuminates and Normal LED 15 blinking until AC source is disconnected 5 4 LCD Display Menu Use Up Down key to select menu displays of the LCD described below This screen will refresh once the system power is enabled Rated Spec Status Frequency 10 Battery Status Output Power Temperature History Record 1
12. tronger charger to support batteries of 500AH up 24 hours operation on the inverter DC start and automatic self diagnostic function THD less than 39 High efficiency design to save electricity Low heat dissipation in long time operation t A 92 N Design to operate under harsh environment 10 3U 19 Rack Mount or WALL Mounted design 11 DC priority or AC priority selectable 1 3 Important Notices 1 Read instructions carefully before operating the Inverter Charger 2 Inverter Charger power connect instruction should be followed 3 Please don t open the case to prevent danger 4 Maximum solar charging current 50 5 Retain the load within the rating of Inverter Charger to prevent faults 6 Keep the Inverter Charger clean and dry 2 SAFTY INSTRUCTION 2 1 Transporting 1 Disconnect all power cables if necessary 2 Be careful not to damage the Inverter Charger while transporting 3 Don t move the Inverter Charger upside down 4 Please transport the Inverter Charger system only in the original packaging to protect against shock and impact 2 2 Positioning 1 Do not put the Inverter Charger on rugged or declined surface 2 Do not install the Inverter Charger near water or in damp environments 3 Do not install the Inverter Charger where it would be exposed to direct sunlight or near heat 4 Do not block off ventilation openings in the Inverter Charger system s ho
13. using and don t leave objects on the top of the Inverter Charger 5 Keep the Inverter Charger far away from heat emitting sources 6 Do not expose it to corrosive gas 7 Ambient temperature OC 40 C 2 3 Installation 1 Connect the Inverter Charger only to an earthed shockproof socket outlet 2 Place cables in such a way that no one can step on or trip over them 2 4 1 Do not disconnect mains cable on the Inverter Charger or the building wiring socket outlet during operations since this would cancel the protective earthing of the Inverter Charger and of all connected loads 2 Ensure that no fluids or other foreign objects can enter the Inverter Charger system 2 5 Maintenance and Service 1 Caution risk of electric shock Even after the unit 15 disconnected from mains power supply building wiring socket outlet components inside the Inverter Charger are still connected to the battery and are still electrically live and dangerous Before carrying out any kind of servicing and or maintenance disconnect the batteries and verify that no current is present 2 Batteries may cause electric shock and have a high short circuit current Please take the precautionary measures specified below and any other measures necessary when working with batteries remove wristwatches rings and other metal objects use only tools with insulated grips and handles CABLE CONNECTION 3 1 Inspectio
14. wn picture Press the Enter key lt at right and then you will be able to see an arrow between SETTING and AC TO AC Press the V key and switch AC TO AC to DC TO AC 15 After finishing setting press the ENTER key lt and move to save option Press the V key and switch NO to YES at save function and then press the ENTER key lt again to save Now we complete the setting for DC TO AC mode Remark In DC TO AC mode AC will not be operated until the DC IN is shut down in other words AC will not start working such as charging or outputting until switching back to AC IN When the system detects that the AC IN is it will switch back to DC TO AC automatically It is running as loop 16 5 7 INPUT VOLTAGE SETTING 17 After startup press the V in the middle and stop at I P VOLT SETTING Press the ENTER key lt at right the arrow will appear at bottom before LO Press the V amp A key to adjust the AC input value for low voltage Press the ENTER key lt again the arrow will switch the position before HI Press the WV amp key to adjust the AC input value for high voltage After finishing setting press the ENTER key lt and move to save option Press the V key switch NO to YES at save function and then press the ENTER key lt again to save Now we complete the setting for adjusting the value
Download Pdf Manuals
Related Search