User Manual
Contents
1. TURBO HD 1080P Dome Camera User Manual Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards as outlined in Ul s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING 0100001041016 THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits fora digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not instal2. that all the related equipment is power off during the installation Check the specification of the products for the installation environment eCheck whether the power supply is matched with your power output to avoid damage e Please make sure the wall is strong enough to withstand three times the weight of the camera and the mounting elf the wall is the cement wall you need to insert expansion screws before you install the camera If the wallis the wooden wall you can use self tapping screw to secure the camera elf the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself 2 1 Ceiling Mounting Steps 1 Drill the screw holes and the cable hole on the ceiling according to the supplied drill template Type II gt gt 1 p Drill Template Hold A for cables uted thi h the rough the wal A Hole A for cables routed through the celling Screw hole 2 for Mounting Base 2 1 2 Gf Figure 2 1 The Drill Template 2 Loosen the screws on the bubble of type 1 camera rotate the bubble of type2 camera to remove the bubble and the black liner Type I Type ll Figure 2 2 Remove the Bubble 3 Attach the back box of type 1 camera base plate of type2 camera to the ceiling and secure them with supplied self tapping screws 4 Route the cables through the cable hole 5 Align th
3. HARPNESS 25 4 CONTRAST 150 5 BRIGHT OFF 1 6 MIRROR ON 7 FLIP ON 8 RETURN RET Figure 3 5 EFFECT Color Gain Color gain adjust this feature to change the saturation of the color You can set the value from Oto 255 Color Hue You can adjust the image HUE from Oto 71 Sharpness Sharpness determines the amount of detail that an imaging system can reproduce You can set the value from 0 to 255 Contrast Contrast enhances the difference in color and light between parts of an image You can set the value from 0 to 255 Bright Off Bright Off refers to the brightness compensation of the image You can set the bright compensation value as Oor 1 Mirror You can set the Mirror status as ON OFF Flip You can set the FLIP status as ON OFF 3 3 7 SYSTEM SYSTEM 1 CAMERA ID 255 2 ID DISP ON 3 NAME DISP ON 4 LANGUAGE ENG 5 FACTORY INIT OFF 6 RETURN RET Figure 3 6 SYSTEM You can setthe camera ID from 0 to 255 Select the ID display and name display status as ON OFF Chinese and English are selectable for the language of the menu You can restore the camera to the default by setting the factory initialization status as ON 3 3 8 EXIT Exit and Save amp exit are selectable
4. e camera with the back box base plate and tighten the set screws to secure the camera with the back box base plate Type I LLLLLLLLLL Type II Figure 2 3 Fix the Camera to the Ceiling 6 Connect the corresponding cables 7 Adjust the camera according to the figure below to get an optimum angle 8 Fit the black liner on the camera and tighten the screws on the bubble of type 1 camera or rotate the bubble of type 2 camera to complete 0 355 os 0 340 P i P Di H R Diaeta E E Direction ge neater irection 0 355 2556 Figure 2 4 3 axis Adjustment 2 2 In ceiling Mounting You need to purchase an in ceiling mount separately if you adopt in celling mounting Steps 1 Drill the screw holes and the cable hole inthe ceiling according to the supplied drill template 2 Screw the bolts through the mount by aligning with the 2 bolt holes Fit the toggles onto the bolts 3 Push the two toggle bolts through the two screw holes on the ceiling Rotate the bolt till the toggle holds the ceiling tightly BT DERRY Figure 2 5 Install the Mount 3 Route and connect the corresponding cables 4 Fix the camera to the in ceiling mount with the supplied screws Figure 2 6 Fix the Camera to the Mount 5 Repeat steps 6 8 of the Ceiling Mounting section to complete the installation 2 3 In ceiling Mounting in ceiling mounting with gang box is supported by the both t
5. ery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info 1 Introduction 1 1 Product Features This camera adopts new generation sensor with high sensitivity and advanced circuit board design technology It possesses the features of high resolution low distortion and low noise etc It is extremely suitable for supervisory system and image processing system The main features are as follows High performance CMOS sensor and high resolution bring high quality image Low illumination Support IR cut filter with auto switch OSD menu parameters are configurable Support auto white balance auto gain control electronic shutter control and internal synchronization SMART IR mode Unit transmission control Advanced 3 axis design meets different installation requirements 1 2 Overview 1 2 1 Overview of Type Dome Camera Power Cable Black Liner Back Box Figure 1 1 Overview of Type I Dome Camera 1 2 2 Overview of Type Il Dome Camera Power Cable HD Video Cable Base plate Bubble Black Liner Figure 1 2 Overview of Type II Dome Camera 2 Installation Before you start e Please make sure that the device in the package is in good condition and all the assembly parts are included Make sure
6. led and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the i supplied accessories too are marked 3 with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European EE Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The batt
7. mode of AUTO you need to set the R G B G Gain and to select an indoor outdoor mode If the AWB mode is select as User You need to set the R G B Gain manually 3 3 4 AE You can set the AE mode as HOLD DC and ESC Brightness Brightness refers to the brightness of the image Shutter Shutter denotes the speed of the shutter You can set the shutter as AUTO 1 25 1 30 1 50 1 60 1 100 1 120 1 250 1 500 1 1k 1 3k and 1 10k Flicker You can set the flicker status as SOHZ 60HZ to prevent image flicking BLC BLC bases on the back area to enhance the brightness of the whole image You can set the BLC gain from Oto 16 AGC AGC optimizes the clarity of image in poor light scene The value of AGC can be set from 1 5 LSC LSC corrects the phenomenon where the image gets darkened or blurred on the periphery 3 3 5 SPECIAL SPECIAL 1 PRIVACY ZONE 2 MOTION 3 HLC 4 RETURN RET Figure 3 4 SPECIAL Privacy zone Select a PRIVACY area Set the MASK PAT as OFF GRAY WHITE or BLACK Set the SX EX SY EY value to define the position and size of the area Motion Set the Motion status as ON or OFF Set the SENSITIVITY from Oto 255 Set the alarm status as ICON TRANCE OFF Set the hold time from O second to 255 seconds HLC HLC supplements the brightness of the peripheral area of the image You can set the mask value and threshold from 0 to 255 3 3 6 EFFECT EFFECT 1 COLOR GAIN 200 2 COLORHUE 200 3 S
8. ypes of camera 1 Repeat steps 2 3 of the In ceiling Mounting section to secure the in ceiling mount supplied to the gang box T 1 Figure 2 7 Install the Mount 2 Route and connect the corresponding cables 3 Align the camera with the gang box and tighten the screws to secure the camera with the gang box 4 Repeat steps 6 8 of the Ceiling Mounting section to complete the installation 3 Menu Operation Menu vimeo our Pavannicut awe AE SPECIAL EFFECT SYSTEM EXIT FRAME auto DC PRIVAC COLOR ae COLOR Crone Can Cpo m S22 Ge o C Cons HOLD i AUTO HOLD HIE SHARPNESS 8000K EXT ET 0 NT RAST ancuace 0 on Figure 3 1 Main Menu A coaxial camera controller purchase separately is required to select the menu and adjust the camera parameters 3 1 VIDEO OUT You can set the frame rate as 25 fps 30fps 3 2 DAY NIGHT Color B W AUTO and EXT are selectable for DAY NIGHT switches Under the mode of the AUTO and EXT you can set the IR LED as Smart and CDS If the IR LED is selected as Smart you can set the bright ness of the IR LED DAY NIGHT AWB BORE AUC 1 MODE AUTO 2 D TON 63 2 R G GAIN 255 3 NTOD 63 3 B G GAIN 151 4 DELAY TIME 20 4 RETURN RET 5 RETURN RET Figure 3 2 DAY NIGHT Figure 3 3 AWB 3 3 3 AWB Auto User Push 8000k 6000k 4200k and 3000k are selectable for AWB Under the
Download Pdf Manuals
Related Search